This commit adds emulation of the magnetometer on the LSM303DLHC.
It allows the magnetometer's X, Y and Z outputs to be set via the
mag-x, mag-y and mag-z properties, as well as the 12-bit
temperature output via the temperature property. Sensor can be
enabled with 'CONFIG_LSM303DLHC_MAG=y'.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Message-id: 20220130095032.35392-1-kevin.townsend@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In most of the ITS command processing, we check different error
possibilities one at a time and log them appropriately. In
process_mapti() and process_mapd() we have code which checks
multiple error cases at once, which means the logging is less
specific than it could be. Split those cases up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-14-peter.maydell@linaro.org
When handling MAPI/MAPTI, we allow the supplied interrupt ID to be
either 1023 or something in the valid LPI range. This is a mistake:
only a real valid LPI is allowed. (The general behaviour of the ITS
is that most interrupt ID fields require a value in the LPI range;
the exception is that fields specifying a doorbell value, which are
all in GICv4 commands, allow also 1023 to mean "no doorbell".)
Remove the condition that incorrectly allows 1023 here.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-13-peter.maydell@linaro.org
In the MAPC command, if V=0 this is a request to delete a collection
table entry and the rdbase field of the command packet will not be
used. In particular, the specification says that the "UNPREDICTABLE
if rdbase is not valid" only applies for V=1.
We were doing a check-and-log-guest-error on rdbase regardless of
whether the V bit was set, and also (harmlessly but confusingly)
storing the contents of the rdbase field into the updated collection
table entry. Update the code so that if V=0 we don't check or use
the rdbase field value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-12-peter.maydell@linaro.org
Currently we track in the TableDesc and CmdQDesc structs the state of
the GITS_BASER<n> and GITS_CBASER Valid bits. However we aren't very
consistent abut checking the valid field: we test it in update_cte()
and update_dte(), but not anywhere else we look things up in tables.
The GIC specification says that it is UNPREDICTABLE if a guest fails
to set any of these Valid bits before enabling the ITS via
GITS_CTLR.Enabled. So we can choose to handle Valid == 0 as
equivalent to a zero-length table. This is in fact how we're already
catching this case in most of the table-access paths: when Valid is 0
we leave the num_entries fields in TableDesc or CmdQDesc set to zero,
and then the out-of-bounds check "index >= num_entries" that we have
to do anyway before doing any of these table lookups will always be
true, catching the no-valid-table case without any extra code.
So we can remove the checks on the valid field from update_cte()
and update_dte(): since these happen after the bounds check there
was never any case when the test could fail. That means the valid
fields would be entirely unused, so just remove them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-11-peter.maydell@linaro.org
Make the update_ite() struct use the new ITEntry struct, so that
callers don't need to assemble the in-memory ITE data themselves, and
only get_ite() and update_ite() need to care about that in-memory
layout. We can then drop the no-longer-used IteEntry struct
definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-10-peter.maydell@linaro.org
In get_ite() we currently return the caller some of the fields of an
Interrupt Table Entry via a set of pointer arguments, and validate
some of them internally (interrupt type and valid bit) to return a
simple true/false 'valid' indication. Define a new ITEntry struct
which has all the fields that the in-memory ITE has, and bring the
get_ite() function in to line with get_dte() and get_cte().
This paves the way for handling virtual interrupts, which will want
a different subset of the fields in the ITE. Handling them under
the old "lots of pointer arguments" scheme would have meant a
confusingly large set of arguments for this function.
The new struct ITEntry is obviously confusably similar to the
existing IteEntry struct, whose fields are the raw 12 bytes
of the in-memory ITE. In the next commit we will make update_ite()
use ITEntry instead of IteEntry, which will allow us to delete
the IteEntry struct and remove the confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-9-peter.maydell@linaro.org
The get_ite() code has some awkward nested if statements; clean
them up by returning early if the memory accesses fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-8-peter.maydell@linaro.org
In get_ite() and update_ite() we work with a 12-byte in-guest-memory
table entry, which we intend to handle as an 8-byte value followed by
a 4-byte value. Unfortunately the calculation of the address of the
4-byte value is wrong, because we write it as:
table_base_address + (index * entrysize) + 4
(obfuscated by the way the expression has been written)
when it should be + 8. This bug meant that we overwrote the top
bytes of the 8-byte value with the 4-byte value. There are no
guest-visible effects because the top half of the 8-byte value
contains only the doorbell interrupt field, which is used only in
GICv4, and the two bugs in the "write ITE" and "read ITE" codepaths
cancel each other out.
We can't simply change the calculation, because this would break
migration of a (TCG) guest from the old version of QEMU which had
in-guest-memory interrupt tables written using the buggy version of
update_ite(). We must also at the same time change the layout of the
fields within the ITE_L and ITE_H values so that the in-memory
locations of the fields we care about (VALID, INTTYPE, INTID and
ICID) stay the same.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-7-peter.maydell@linaro.org
Make update_cte() take a CTEntry struct rather than all the fields
of the new CTE as separate arguments.
This brings it into line with the update_dte() API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-6-peter.maydell@linaro.org
In the ITS, a CTE is an entry in the collection table, which contains
multiple fields. Currently the function get_cte() which reads one
entry from the device table returns a success/failure boolean and
passes back the raw 64-bit integer CTE value via a pointer argument.
We then extract fields from the CTE as we need them.
Create a real C struct with the same fields as the CTE, and
populate it in get_cte(), so that that function and update_cte()
are the only ones which need to care about the in-guest-memory
format of the CTE.
This brings get_cte()'s API into line with get_dte().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-5-peter.maydell@linaro.org
Make update_dte() take a DTEntry struct rather than all the fields of
the new DTE as separate arguments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-4-peter.maydell@linaro.org
In the ITS, a DTE is an entry in the device table, which contains
multiple fields. Currently the function get_dte() which reads one
entry from the device table returns it as a raw 64-bit integer,
which we then pass around in that form, only extracting fields
from it as we need them.
Create a real C struct with the same fields as the DTE, and
populate it in get_dte(), so that that function and update_dte()
are the only ones that need to care about the in-guest-memory
format of the DTE.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-3-peter.maydell@linaro.org
Currently the ITS accesses each 8-byte doubleword in a 4-doubleword
command packet with a separate address_space_ldq_le() call. This is
awkward because the individual command processing functions have
ended up with code to handle "load more doublewords out of the
packet", which is both unwieldy and also a potential source of bugs
because it's not obvious when looking at a line that pulls a field
out of the 'value' variable which of the 4 doublewords that variable
currently holds.
Switch to using address_space_map() to map the whole command packet
at once and fish the four doublewords out of it. Then each process_*
function can start with a few lines of code that extract the fields
it cares about.
This requires us to split out the guts of process_its_cmd() into a
new do_process_its_cmd(), because we were previously overloading the
value and offset arguments as a backdoor way to directly pass the
devid and eventid from a write to GITS_TRANSLATER. The new
do_process_its_cmd() takes those arguments directly, and
process_its_cmd() is just a wrapper that does the "read fields from
command packet" part.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-2-peter.maydell@linaro.org
We currently miss a bunch of register resets in the device reset
function. This sometimes prevents the guest from rebooting after
a system_reset (with virtio-blk-pci). For instance, we may get
the following errors:
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid read at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid write at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220202111602.627429-1-eric.auger@redhat.com
Fixes: 10a83cb988 ("hw/arm/smmuv3: Skeleton")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Starting the SysTick timer and changing the clock source a the same time
will result in an error, if the previous clock period was zero. For exmaple,
on the mps2-tz platforms, no refclk is present. Right after reset, the
configured ptimer period is zero, and trying to enabling it will turn it off
right away. E.g., code running on the platform setting
SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | SysTick_CTRL_ENABLE_Msk;
should change the clock source and enable the timer on real hardware, but
resulted in an error in qemu.
Signed-off-by: Richard Petri <git@rpls.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220201192650.289584-1-git@rpls.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Always call arm_load_kernel() regardless of kernel_filename being
set. This is needed because arm_load_kernel() sets up reset for
the CPUs.
Fixes: 6f16da53ff (hw/arm: versal: Add a virtual Xilinx Versal board)
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220130110313.4045351-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're using PSCI emulation, we add a /psci node to the device tree
we pass to the guest. At the moment, if the dtb already has a /psci
node in it, we retain it, rather than replacing it. (This behaviour
was added in commit c39770cd63 in 2018.)
This is a problem if the existing node doesn't match our PSCI
emulation. In particular, it might specify the wrong method (HVC vs
SMC), or wrong function IDs for cpu_suspend/cpu_off/etc, in which
case the guest will not get the behaviour it wants when it makes PSCI
calls.
An example of this is trying to boot the highbank or midway board
models using the device tree supplied in the kernel sources: this
device tree includes a /psci node that specifies function IDs that
don't match the (PSCI 0.2 compliant) IDs that QEMU uses. The dtb
cpu_suspend function ID happens to match the PSCI 0.2 cpu_off ID, so
the guest hangs after booting when the kernel tries to idle the CPU
and instead it gets turned off.
Instead of retaining an existing /psci node, delete it entirely
and replace it with a node whose properties match QEMU's PSCI
emulation behaviour. This matches the way we handle /memory nodes,
where we also delete any existing nodes and write in ones that
match the way QEMU is going to behave.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-17-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
The highbank and midway board code includes boot-stub code for
handling secondary CPU boot which keeps the secondaries in a pen
until the primary writes to a known location with the address they
should jump to.
This code is never used, because the boards enable QEMU's PSCI
emulation, so secondary CPUs are kept powered off until the PSCI call
which turns them on, and then start execution from the address given
by the guest in that PSCI call. Delete the unreachable code.
(The code was wrong for midway in any case -- on the Cortex-A15 the
GIC CPU interface registers are at a different offset from PERIPHBASE
compared to the Cortex-A9, and the code baked-in the offsets for
highbank's A9.)
Note that this commit implicitly depends on the preceding "Don't
write secondary boot stub if using PSCI" commit -- the default
secondary-boot stub code overlaps with one of the highbank-specific
bootcode rom blobs, so we must suppress the secondary-boot
stub code entirely, not merely replace the highbank-specific
version with the default.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-15-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Now that we have dealt with the one special case (highbank) that needed
to set both psci_conduit and secure_board_setup, we don't need to
allow that combination any more. It doesn't make sense in general,
so use an assertion to ensure we don't add new boards that do it
by accident without thinking through the consequences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-13-peter.maydell@linaro.org
Guest code on highbank may make non-PSCI SMC calls in order to
enable/disable the L2x0 cache controller (see the Linux kernel's
arch/arm/mach-highbank/highbank.c highbank_l2c310_write_sec()
function). The ABI for this is documented in kernel commit
8e56130dcb as being borrowed from the OMAP44xx ROM. The OMAP44xx TRM
documents this function ID as having no return value and potentially
trashing all guest registers except SP and PC. For QEMU's purposes
(where our L2x0 model is a stub and enabling or disabling it doesn't
affect the guest behaviour) a simple "do nothing" SMC is fine.
We currently implement this NOP behaviour using a little bit of
Secure code we run before jumping to the guest kernel, which is
written by arm_write_secure_board_setup_dummy_smc(). The code sets
up a set of Secure vectors where the SMC entry point returns without
doing anything.
Now that the PSCI SMC emulation handles all SMC calls (setting r0 to
an error code if the input r0 function identifier is not recognized),
we can use that default behaviour as sufficient for the highbank
cache controller call. (Because the guest code assumes r0 has no
interesting value on exit it doesn't matter that we set it to the
error code). We can therefore delete the highbank board code that
sets secure_board_setup to true and writes the secure-code bootstub.
(Note that because the OMAP44xx ABI puts function-identifiers in
r12 and PSCI uses r0, we only avoid a clash because Linux's code
happens to put the function-identifier in both registers. But this
is true also when the kernel is running on real firmware that
implements both ABIs as far as I can see.)
This change fixes in passing booting on the 'midway' board model,
which has been completely broken since we added support for Hyp
mode to the Cortex-A15 CPU. When we did that boot.c was made to
start running the guest code in Hyp mode; this includes the
board_setup hook, which instantly UNDEFs because the NSACR is
not accessible from Hyp. (Put another way, we never made the
secure_board_setup hook support cope with Hyp mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-12-peter.maydell@linaro.org
Change the highbank/midway boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit and start-powered-off
properties on the CPU objects in the board code, and instead set the
psci_conduit field in the arm_boot_info struct to tell the common
boot loader code that we'd like PSCI if the guest is starting at an
EL that it makes sense with (in which case it will set these
properties).
This means that when running guest code at EL3, all the cores
will start execution at once on poweron. This matches the
real hardware behaviour. (A brief description of the hardware
boot process is in the u-boot documentation for these boards:
https://u-boot.readthedocs.io/en/latest/board/highbank/highbank.html#boot-process
-- in theory one might run the 'a9boot'/'a15boot' secure monitor
code in QEMU, though we probably don't emulate enough for that.)
This affects the highbank and midway boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-10-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the virt board code, set the arm_boot_info psci_conduit
field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel or to the generic loader. (EL3 guest code started
via -bios or -pflash was already being run with PSCI emulation
disabled.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-9-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Change the Xilinx ZynqMP-based board xlnx-zcu102 to use the new
boot.c functionality to allow us to enable psci-conduit only if
the guest is being booted in EL1 or EL2, so that if the user runs
guest EL3 firmware code our PSCI emulation doesn't get in its
way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
Note that this means that EL3 guest code will have no way
to power on secondary cores, because we don't model any
kind of power controller that does that on this SoC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-7-peter.maydell@linaro.org
Change the allwinner-h3 based board to use the new boot.c
functionality to allow us to enable psci-conduit only if the guest is
being booted in EL1 or EL2, so that if the user runs guest EL3
firmware code our PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes sense
with.
This affects the orangepi-pc board.
This commit leaves the secondary CPUs in the powered-down state if
the guest is booting at EL3, which is the same behaviour as before
this commit. The secondaries can no longer be started by that EL3
code making a PSCI call but can still be started via the CPU
Configuration Module registers (which we model in
hw/misc/allwinner-cpucfg.c).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-6-peter.maydell@linaro.org
Change the iMX-SoC based boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
This affects the mcimx6ul-evk and mcimx7d-sabre boards.
Note that for the mcimx7d board, this means that when running guest
code at EL3 there is currently no way to power on the secondary CPUs,
because we do not currently have a model of the system reset
controller module which should be used to do that for the imx7 SoC,
only for the imx6 SoC. (Previously EL3 code which knew it was
running on QEMU could use a PSCI call to do this.) This doesn't
affect the imx6ul-evk board because it is uniprocessor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-5-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change exposes ACPI ERST support for x86 guests.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-8-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This builds the ACPI ERST table to inform OSPM how to communicate
with the acpi-erst device.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-7-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This implements a PCI device for ACPI ERST. This implements the
non-NVRAM "mode" of operation for ERST as it is supported by
Linux and Windows.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-6-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit [2] broke original '\0' padding of OEM ID and OEM Table ID
fields in headers of ACPI tables. While it doesn't have impact on
default values since QEMU uses 6 and 8 characters long values
respectively, it broke usecase where IDs are provided on QEMU CLI.
It shouldn't affect guest (but may cause licensing verification
issues in guest OS).
One of the broken usecases is user supplied SLIC table with IDs
shorter than max possible length, where [2] mangles IDs with extra
spaces in RSDT and FADT tables whereas guest OS expects those to
mirror the respective values of the used SLIC table.
Fix it by replacing whitespace padding with '\0' padding in
accordance with [1] and expectations of guest OS
1) ACPI spec, v2.0b
17.2 AML Grammar Definition
...
//OEM ID of up to 6 characters. If the OEM ID is
//shorter than 6 characters, it can be terminated
//with a NULL character.
2)
Fixes: 602b458201 ("acpi: Permit OEM ID and OEM table ID fields to be changed")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/707
Reported-by: Dmitry V. Orekhov <dima.orekhov@gmail.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-stable@nongnu.org
Message-Id: <20220112130332.1648664-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Tested-by: Dmitry V. Orekhov dima.orekhov@gmail.com
We already have a CONFIG_ISAPC switch - but we're not using it yet.
Add some "#ifdefs" to make it possible to disable this machine now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220107160713.235918-1-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patchset fixes some important bugs in the hppa artist graphics driver:
- Fix artist graphics for HP-UX and Linux
- Mouse cursor fixes for HP-UX
- Fix draw_line() function on artist graphic
and it adds new qemu features for hppa:
- Allow up to 16 emulated CPUs (instead of 8)
- Add support for an emulated TOC/NMI button
A new Seabios-hppa firmware is included as well:
- Update SeaBIOS-hppa to VERSION 3
- New opt/hostid fw_cfg option to change hostid
- Add opt/console fw_cfg option to select default console
- Added 16x32 font to STI firmware
Signed-off-by: Helge Deller <deller@gmx.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYfrIogAKCRD3ErUQojoP
X93ZAP9hqp/FCz/goH7Tpqce6FspHriJm6Ej2Rd7HxZWmh4bpQD/cMjY8qpcA/6r
Nx4bgRPT6kCZwwLx7v2jZ2QsA2KaZAM=
=c0qO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/hdeller/tags/hppa-updates-pull-request' into staging
Fixes and updates for hppa target
This patchset fixes some important bugs in the hppa artist graphics driver:
- Fix artist graphics for HP-UX and Linux
- Mouse cursor fixes for HP-UX
- Fix draw_line() function on artist graphic
and it adds new qemu features for hppa:
- Allow up to 16 emulated CPUs (instead of 8)
- Add support for an emulated TOC/NMI button
A new Seabios-hppa firmware is included as well:
- Update SeaBIOS-hppa to VERSION 3
- New opt/hostid fw_cfg option to change hostid
- Add opt/console fw_cfg option to select default console
- Added 16x32 font to STI firmware
Signed-off-by: Helge Deller <deller@gmx.de>
# gpg: Signature made Wed 02 Feb 2022 18:08:34 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* remotes/hdeller/tags/hppa-updates-pull-request:
hw/display/artist: Fix draw_line() artefacts
hw/display/artist: Mouse cursor fixes for HP-UX
hw/display/artist: rewrite vram access mode handling
hppa: Add support for an emulated TOC/NMI button.
hw/hppa: Allow up to 16 emulated CPUs
seabios-hppa: Update SeaBIOS-hppa to VERSION 3
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The draw_line() function left artefacts on the screen because it was using the
x/y variables which were incremented in the loop before. Fix it by using the
unmodified x1/x2 variables instead.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
This patch fix the behaviour and positioning of the X11 mouse cursor in HP-UX.
The current code missed to subtract the offset of the CURSOR_CTRL register from
the current mouse cursor position. The HP-UX graphics driver stores in this
register the offset of the mouse graphics compared to the current cursor
position. Without this adjustment the mouse behaves strange at the screen
borders.
Additionally, depending on the HP-UX version, the mouse cursor position
in the cursor_pos register reports different values. To accommodate this
track the current min and max reported values and auto-adjust at runtime.
With this fix the mouse now behaves as expected on HP-UX 10 and 11.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
When writing this code it was assumed that register 0x118000 is the
buffer access mode for color map accesses. It turned out that this
is wrong. Instead register 0x118000 sets both src and dst buffer
access mode at the same time.
This required a larger rewrite of the code. The good thing is that
both the linear framebuffer and the register based vram access can
now be combined into one function.
This makes the linux 'stifb' framebuffer work, and both HP-UX 10.20
and HP-UX 11.11 are still working.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: qemu-stable@nongnu.org
Signed-off-by: Helge Deller <deller@gmx.de>
Almost all PA-RISC machines have either a button that is labeled with 'TOC' or
a BMC/GSP function to trigger a TOC. TOC is a non-maskable interrupt that is
sent to the processor. This can be used for diagnostic purposes like obtaining
a stack trace/register dump or to enter KDB/KGDB in Linux.
This patch adds support for such an emulated TOC button.
It wires up the qemu monitor "nmi" command to trigger a TOC. For that it
provides the hppa_nmi function which is assigned to the nmi_monitor_handler
function pointer. When called it raises the EXCP_TOC hardware interrupt in the
hppa_cpu_do_interrupt() function. The interrupt function then calls the
architecturally defined TOC function in SeaBIOS-hppa firmware (at fixed address
0xf0000000).
According to the PA-RISC PDC specification, the SeaBIOS firmware then writes
the CPU registers into PIM (processor internal memmory) for later analysis. In
order to write all registers it needs to know the contents of the CPU "shadow
registers" and the IASQ- and IAOQ-back values. The IAOQ/IASQ values are
provided by qemu in shadow registers when entering the SeaBIOS TOC function.
This patch adds a new aritificial opcode "getshadowregs" (0xfffdead2) which
restores the original values of the shadow registers. With this opcode SeaBIOS
can store those registers as well into PIM before calling an OS-provided TOC
handler.
To trigger a TOC, switch to the qemu monitor with Ctrl-A C, and type in the
command "nmi". After the TOC started the OS-debugger, exit the qemu monitor
with Ctrl-A C.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This brings the hppa_hardware.h file in sync with the copy in the
SeaBIOS-hppa sources.
In order to support up to 16 CPUs, it's required to move the HPA for
MEMORY_HPA out of the address space of the new 16th CPU.
The new address of 0xfffff000 worked well for Linux and HP-UX, while
other addresses close to the former 0xfffbf000 area are used by the
architecture for local and global broadcasts.
The PIM_STORAGE_SIZE constant is used in SeaBIOS sources and
is relevant for the TOC/NMI feature.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Hi
This time I have disabled vmstate canary patches form Dave Gilbert.
Let's see if it works.
Later, Juan.
-----BEGIN PGP SIGNATURE-----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=F/ek
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/quintela-gitlab/tags/migration-20220128-pull-request' into staging
Migration Pull request (Take 2)
Hi
This time I have disabled vmstate canary patches form Dave Gilbert.
Let's see if it works.
Later, Juan.
# gpg: Signature made Fri 28 Jan 2022 18:30:25 GMT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/quintela-gitlab/tags/migration-20220128-pull-request: (36 commits)
migration: Move temp page setup and cleanup into separate functions
migration: Simplify unqueue_page()
migration: Add postcopy_has_request()
migration: Enable UFFD_FEATURE_THREAD_ID even without blocktime feat
migration: No off-by-one for pss->page update in host page size
migration: Tally pre-copy, downtime and post-copy bytes independently
migration: Introduce ram_transferred_add()
migration: Don't return for postcopy_send_discard_bm_ram()
migration: Drop return code for disgard ram process
migration: Do chunk page in postcopy_each_ram_send_discard()
migration: Drop postcopy_chunk_hostpages()
migration: Don't return for postcopy_chunk_hostpages()
migration: Drop dead code of ram_debug_dump_bitmap()
migration/ram: clean up unused comment.
migration: Report the error returned when save_live_iterate fails
migration/migration.c: Remove the MIGRATION_STATUS_ACTIVE when migration finished
migration/migration.c: Avoid COLO boot in postcopy migration
migration/migration.c: Add missed default error handler for migration state
Remove unnecessary minimum_version_id_old fields
multifd: Rename pages_used to normal_pages
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
-----BEGIN PGP SIGNATURE-----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=m7N5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220128' into staging
target-arm queue:
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
# gpg: Signature made Fri 28 Jan 2022 15:29:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220128: (32 commits)
target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
hw/arm: ast2600: Fix address mapping of second SPI controller
hw/intc/arm_gicv3_its: Implement MOVI
hw/intc/arm_gicv3_its: Implement MOVALL
hw/intc/arm_gicv3_its: Check table bounds against correct limit
hw/intc/arm_gicv3_its: Make GITS_BASER<n> RAZ/WI for unimplemented registers
hw/intc/arm_gicv3_its: Provide read accessor for translation_ops
hw/intc/arm_gicv3: Set GICR_CTLR.CES if LPIs are supported
hw/intc/arm_gicv3_redist: Remove unnecessary zero checks
hw/intc/arm_gicv3_its: Sort ITS command list into numeric order
hw/intc/arm_gicv3: Honour GICD_CTLR.EnableGrp1NS for LPIs
hw/intc/arm_gicv3_its: Don't clear GITS_CWRITER on writes to GITS_CBASER
hw/intc/arm_gicv3_its: Don't clear GITS_CREADR when GITS_CTLR.ENABLED is set
hw/intc/arm_gicv3: Initialise dma_as in GIC, not ITS
hw/intc/arm_gicv3_its: Add tracepoints
target/arm: Log CPU index in 'Taking exception' log
scripts: Explain the difference between linux-headers and standard-headers
MAINTAINERS: Remove myself (for raspi).
MAINTAINERS: Add an entry for Xilinx Versal OSPI
hw/arm/xlnx-versal-virt: Connect mt35xu01g flashes to the OSPI
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The migration code will not look at a VMStateDescription's
minimum_version_id_old field unless that VMSD has set the
load_state_old field to something non-NULL. (The purpose of
minimum_version_id_old is to specify what migration version is needed
for the code in the function pointed to by load_state_old to be able
to handle it on incoming migration.)
We have exactly one VMSD which still has a load_state_old,
in the PPC CPU; every other VMSD which sets minimum_version_id_old
is doing so unnecessarily. Delete all the unnecessary ones.
Commit created with:
sed -i '/\.minimum_version_id_old/d' $(git grep -l '\.minimum_version_id_old')
with the one legitimate use then hand-edited back in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
---
It missed vmstate_ppc_cpu.
Address should be 0x1E631000 and not 0x1E641000 as initially introduced.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/838
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Suggested-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220126083520.4135713-1-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
mrm
Clément RIVOLA
0xMirasio
Kevin Townsend
Peter Maydell
Eric Auger
Richard Petri
Edgar E. Iglesias
Francisco Iglesias
Eric DeVolder
Igor Mammedov
Thomas Huth
Sven Schnelle
Helge Deller
Cédric Le Goater