Upstream NBD protocol recently added the ability to efficiently
write zeroes without having to send the zeroes over the wire,
along with a flag to control whether the client wants a hole.
The generic block code takes care of falling back to the obvious
write of lots of zeroes if we return -ENOTSUP because the server
does not have WRITE_ZEROES.
Ideally, since NBD_CMD_WRITE_ZEROES does not involve any data
over the wire, we want to support transactions that are much
larger than the normal 32M limit imposed on NBD_CMD_WRITE. But
the server may still have a limit smaller than UINT_MAX, so
until experimental NBD protocol additions for advertising various
command sizes is finalized (see [1], [2]), for now we just stick to
the same limits as normal writes.
[1] https://github.com/yoe/nbd/blob/extension-info/doc/proto.md
[2] https://sourceforge.net/p/nbd/mailman/message/35081223/
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-17-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upstream NBD protocol recently added the ability to efficiently
write zeroes without having to send the zeroes over the wire,
along with a flag to control whether the client wants to allow
a hole.
Note that when it comes to requiring full allocation, vs.
permitting optimizations, the NBD spec intentionally picked a
different sense for the flag; the rules in qemu are:
MAY_UNMAP == 0: must write zeroes
MAY_UNMAP == 1: may use holes if reads will see zeroes
while in NBD, the rules are:
FLAG_NO_HOLE == 1: must write zeroes
FLAG_NO_HOLE == 0: may use holes if reads will see zeroes
In all cases, the 'may use holes' scenario is optional (the
server need not use a hole, and must not use a hole if
subsequent reads would not see zeroes).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-16-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
NBD commit 6d34500b clarified how clients and servers are supposed
to behave before closing a connection. It added NBD_REP_ERR_SHUTDOWN
(for the server to announce it is about to go away during option
haggling, so the client should quit sending NBD_OPT_* other than
NBD_OPT_ABORT) and ESHUTDOWN (for the server to announce it is about
to go away during transmission, so the client should quit sending
NBD_CMD_* other than NBD_CMD_DISC). It also clarified that
NBD_OPT_ABORT gets a reply, while NBD_CMD_DISC does not.
This patch merely adds the missing reply to NBD_OPT_ABORT and teaches
the client to recognize server errors. Actually teaching the server
to send NBD_REP_ERR_SHUTDOWN or ESHUTDOWN would require knowing that
the server has been requested to shut down soon (maybe we could do
that by installing a SIGINT handler in qemu-nbd, which transitions
from RUNNING to a new state that waits for the client to react,
rather than just out-right quitting - but that's a bigger task for
another day).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-15-git-send-email-eblake@redhat.com>
[Move dummy ESHUTDOWN to include/qemu/osdep.h. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Checkpatch complains that 'return EINVAL' is usually wrong
(since we tend to favor 'return -EINVAL'). But it is a
false positive for nbd_errno_to_system_errno(). Since NBD
may add future defined wire values, refactor the code to
keep checkpatch happy.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-14-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NBD Protocol allows the server and client to mutually agree
on a shorter handshake (omit the 124 bytes of reserved 0), via
the server advertising NBD_FLAG_NO_ZEROES and the client
acknowledging with NBD_FLAG_C_NO_ZEROES (only possible in
newstyle, whether or not it is fixed newstyle). It doesn't
shave much off the wire, but we might as well implement it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alex Bligh <alex@alex.org.uk>
Message-Id: <1476469998-28592-13-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since we know that the maximum name we are willing to accept
is small enough to stack-allocate, rework the iteration over
NBD_OPT_LIST responses to reuse a stack buffer rather than
allocating every time. Furthermore, we don't even have to
allocate if we know the server's length doesn't match what
we are searching for.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-12-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The server has a nice helper function nbd_negotiate_drop_sync()
which lets it easily ignore fluff from the client (such as the
payload to an unknown option request). We can't quite make it
common, since it depends on nbd_negotiate_read() which handles
coroutine magic, but we can copy the idea into the client where
we have places where we want to ignore data (such as the
description tacked on the end of NBD_REP_SERVER).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-11-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NBD spec says that a client should send NBD_OPT_ABORT
rather than just dropping the connection, if the client doesn't
like something the server sent during option negotiation. This
is a best-effort attempt only, and can only be done in places
where we know the server is still in sync with what we've sent,
whether or not we've read everything the server has sent.
Technically, the server then has to reply with NBD_REP_ACK, but
it's not worth complicating the client to wait around for that
reply.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-10-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than open-coding each option request, it's easier to
have common helper functions do the work. That in turn requires
having convenient packed types for handling option requests
and replies.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-9-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NBD Protocol allows us to send human-readable messages
along with any NBD_REP_ERR error during option negotiation;
make use of this fact for clients that know what to do with
our message.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-8-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than open-coding NBD_REP_SERVER, reuse the code we
already have by adding a length parameter. Additionally,
the refactoring will make adding NBD_OPT_GO in a later patch
easier.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-7-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Our coding convention prefers CamelCase names, and we already
have other existing structs with NBDFoo naming. Let's be
consistent, before later patches add even more structs.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-6-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's better to use consistent capitalization of the namespace
used for NBD functions; we have more instances of NBD* than
Nbd*.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-5-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have both 'struct NBDRequest' and 'struct nbd_request'; making
it confusing to see which does what. Furthermore, we want to
rename nbd_request to align with our normal CamelCase naming
conventions. So, rename the struct which is used to associate
the data received during request callbacks, while leaving the
shorter name for the description of the request sent over the
wire in the NBD protocol.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-4-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Current upstream NBD documents that requests have a 16-bit flags,
followed by a 16-bit type integer; although older versions mentioned
only a 32-bit field with masking to find flags. Since the protocol
is in network order (big-endian over the wire), the ABI is unchanged;
but dealing with the flags as a separate field rather than masking
will make it easier to add support for upcoming NBD extensions that
increase the number of both flags and commands.
Improve some comments in nbd.h based on the current upstream
NBD protocol (https://github.com/yoe/nbd/blob/master/doc/proto.md),
and touch some nearby code to keep checkpatch.pl happy.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-3-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The NBD protocol allows servers to advertise a human-readable
description alongside an export name during NBD_OPT_LIST. Add
an option to pass through the user's string to the NBD client.
Doing this also makes it easier to test commit 200650d4, which
is the client counterpart of receiving the description.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1476469998-28592-2-git-send-email-eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the memory backend file is not large enough to hold the required 'size',
Qemu will report error and exit.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Message-Id: <20161027042300.5929-3-haozhong.zhang@intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20161102010551.2723-1-haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 35c5a52d "acpi: do not use TARGET_PAGE_SIZE" changed struct
NvdimmDsmIn from a variable-size structure to a fixed-size structure of
4096 bytes. It forgot to adjust an assert in
nvdimm_dsm_set_label_data(..., NvdimmDsmIn *in, ...):
assert(sizeof(*in) + sizeof(*set_label_data) + set_label_data->length <=
4096);
which could crash QEMU when guest writes NVDIMM labels.
Fix it by replacing sizeof(*in) by offsetof(NvdimmDsmIn, arg3).
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The initialization was missed before, resulting in some
bad data in the smbus case.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I misunderstood the workings of the power settings, the power off
is a force off operation and there needs to be a separate graceful
shutdown operation. So replace the force off operation with a
graceful shutdown.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The original commit:
commit 67aa56fc03
Author: Corey Minyard <cminyard@mvista.com>
Date: Thu Dec 17 12:50:06 2015 -0600
ipmi: Add an external connection simulation interface
defined a new variable CONFIG_IPMI_EXTERN, but then went
on to mistakely use the pre-existing CONFIG_IPMI_LOCAL
variable.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is allowed by the IPMI specification for graceful shutdown,
so implement it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When issuing a chassis 'powerdown' control command, the routine
qemu_system_shutdown_request() should be used to exit the guest.
qemu_system_powerdown_request() will initiate a soft shutdown which is
not what is required by the IPMI (28.3 Chassis Control Command):
0h = power down. Force system into soft off (S4/S45) state. This
is for 'emergency' management power down actions. The command does
not initiate a clean shut-down of the operating system prior to
powering down the system
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of the unnecessary mutex, it was a vestige
of something else that was not done. That way we don't
have to free it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No hotplug support, make sure it doesn't happen.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
_GPE.E04 is dedicated for nvdimm device hotplug
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
_FIT is required for hotplug support, guest will inquire the updated
device info from it if a hotplug event is received
As FIT buffer is not completely mapped into guest address space, so a
new function, Read FIT whose UUID is UUID
648B9CF2-CDA1-4312-8AD9-49C4AF32BD62, handle 0x10000, function index
is 0x1, is reserved by QEMU to read the piece of FIT buffer. The buffer
is concatenated before _FIT return
Refer to docs/specs/acpi-nvdimm.txt for detailed design
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The buffer is used to save the FIT info for all the presented nvdimm
devices which is updated after the nvdimm device is plugged or
unplugged. In the later patch, it will be used to construct NVDIMM
ACPI _FIT method which reflects the presented nvdimm devices after
nvdimm hotplug
As FIT buffer can not completely mapped into guest address space,
OSPM will exit to QEMU multiple times, however, there is the race
condition - FIT may be changed during these multiple exits, so that
some rules are introduced:
1) the user should hold the @lock to access the buffer and
2) mark @dirty whenever the buffer is updated.
@dirty is cleared for the first time OSPM gets fit buffer, if
dirty is detected in the later access, OSPM will restart the
access
As fit should be updated after nvdimm device is successfully realized
so that a new hotplug callback, post_hotplug, is introduced
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For each NVDIMM present or intended to be supported by platform,
platform firmware also exposes an ACPI Namespace Device under
the root device
So it builds nvdimm devices for all slots to support vNVDIMM hotplug
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are some names repeatedly used in acpi code, define them
as macros to refine the code
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rename it as dsm_out_buf_siz is more descriptive
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the arch dependent info, TARGET_PAGE_SIZE, has been dropped
from nvdimm acpi code, it can be compiled arch-independently
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the function only has 5 args, we use local7 instead of it
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As ARG3 is a reserved name, we rename it to FARG
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to ACPI 6.0 spec, "Memory Device Physical Address
Region Base" in memdev is defined as "This field provides the
Device Physical Address base of the region". This field should
be zero in our case
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Based on ACPI spec:
RegionOffset := TermArg => Integer
However, Named object is not a TermArg.
This patch moves OperationRegion to NCAL() and uses localX as
its RegionOffset
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, 'RLEN' is the totally buffer size written by QEMU and it is
ACPI internally used only. The buffer size returned to guest should
not include 'RLEN' itself
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch includes two parts: Cryptodev Backends
and virtio-crypto stuff. I can maintain cryptodev backends
which introduced by myself. For virtio-crypto stuff, I can
share the work with Michael (The whole virtio supporter).
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make crypto operations are executed asynchronously,
so that other QEMU threads and monitor couldn't
be blocked at the virtqueue handling context.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We use an opaque point to the VirtIOCryptoReq which
can support different packets based on different
algorithms.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduces VirtIOCryptoReq structure to store
crypto request so that we can easily support
asynchronous crypto operation in the future.
At present, we only support cipher and algorithm
chaining.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Realize the symmetric algorithm control queue handler,
including plain cipher and chainning algorithms.
Currently the control queue is used to create and
close session for symmetric algorithm.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Expose the capacity of algorithms supported by
virtio crypto device to the frontend driver using
pci configuration space.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds virtio-crypto-pci, which is the pci proxy for the virtio
crypto device.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the virtio crypto realization, I'll
finish the core code in the following patches. The
thoughts came from virtio net realization.
For more information see:
http://qemu-project.org/Features/VirtioCrypto
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The version of tcg_gen_ld8s_i64 for 32-bit systems does a load into
the low part of the return value - then attempts a sign extension into
the high part, but wrongly sets the high part to a sign extension of
itself rather than of the low part. This results in TCG internal
errors from the use of the uninitialized high part (in some GCC tests
of AArch64 NEON shift intrinsics, in particular). This patch corrects
the sign-extension logic, making it match other functions such as
tcg_gen_ld16s_i64.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Message-Id: <alpine.DEB.2.20.1610272333560.22353@digraph.polyomino.org.uk>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The typedefs we use for the TCGv_i32, TCGv_i64 and TCGv_ptr
types are somewhat confusing, because we define them as
pointers to structs, but the structs themselves are never
defined. Explain in the comments a bit more clearly why
this is OK and what is going on under the hood.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1477067922-26202-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use tcg_gen_mul_tl for muli and mul instructions.
Use tcg_gen_muls2_tl for mulh instruction.
Use tcg_gen_mulu2_tl for mulhu instruction.
Use tcg_gen_mulsu2_tl for mulhsu instruction.
Note that this last fixes a bug, in that mulhsu was
previously treating both operands as signed, instead
of treating rb as unsigned.
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1475011433-24456-3-git-send-email-rth@twiddle.net>