(In QEMU, we call this the "select" register.)
My memory isn't good enough to memorize what these magic runes
do. Label them to prevent mixups from happening in the future.
Side note: I assume it's safe to always set 0xA0 even though ATA2 claims
these bits are reserved, because ATA3 immediately reinstated that these
bits should be always on. ATA4 and subsequent specs only claim that the
fields are obsolete, so I assume it's safe to leave these set and that
it should work with the widest array of guests.
Signed-off-by: John Snow <jsnow@redhat.com>
I have been staring at this FIXME for years and I never knew what it
meant. I finally stumbled across it!
When writing to the command registers, the old value is shifted into a
HOB copy of the register and the new value is written into the primary
register. When reading registers, the value retrieved is dependent on
the HOB bit in the CONTROL register.
By setting bit 7 (0x80) in CONTROL, any register read will, if it has
one, yield the HOB value for that register instead.
Our code has a problem: We were using bit 7 of the DEVICE register to
model this. We use bus->cmd roughly as the control register already, as
it stores the value from ide_ctrl_write.
Lastly, all command register writes reset the HOB, so fix that, too.
Signed-off-by: John Snow <jsnow@redhat.com>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QEMU's kvmclock device is only created when KVM PV feature bits for
kvmclock (KVM_FEATURE_CLOCKSOURCE/KVM_FEATURE_CLOCKSOURCE2) are
exposed to the guest. With 'kvm=off' cpu flag the device is not
created and we don't call KVM_GET_CLOCK/KVM_SET_CLOCK upon migration.
It was reported that without these call at least Hyper-V TSC page
clocksouce (which can be enabled independently) gets broken after
migration.
Switch to creating kvmclock QEMU device unconditionally, it seems
to always make sense to call KVM_GET_CLOCK/KVM_SET_CLOCK on migration.
Use KVM_CAP_ADJUST_CLOCK check instead of CPUID feature bits.
Reported-by: Antoine Damhet <antoine.damhet@blade-group.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200922151934.899555-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PCMachineState type is only used under hw/i386/.
We don't need to forward-declare it for all architectures,
restrict it to the X86 one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xen_hvm_init() is restricted to the X86 architecture.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As this header use the ram_addr_t type, it has to include
"exec/cpu-common.h" to avoid odd errors such:
include/sysemu/xen.h:35:44: error: unknown type name 'ram_addr_t'; did you mean 'in_addr_t'?
35 | static inline void xen_hvm_modified_memory(ram_addr_t start, ram_addr_t length)
| ^~~~~~~~~~
| in_addr_t
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xen_hvm_init() is only meanful to initialize a X86/PC machine,
rename it as xen_hvm_init_pc().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the whole contents of the overview doc comment from object.h
to qom.rst.
This makes the documentation source easier to read and edit, and
also solves the backslash escaping issue at the typecasting macro
examples.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-10-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all example/codelisting markup to Sphinx code-block.
There are a few sections where backslashes at the end of lines
break code formatting. A comment was added noting that this is
an issue.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-8-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This indents existing code examples that are not indented yet,
just to make future conversion to Sphinx markup easier to review.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-7-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add DOC: section keyword to introduction doc comment, so it will
be rendered by kernel-doc.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-5-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kernel-doc syntax for indicating private and public struct
fields.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-3-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kernel-doc requires all function parameters to be documented, so
document them all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200910221526.10041-2-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Last uses of memory_region_clear_global_locking() have been
removed in commit 7070e085d4 ("acpi: mark PMTIMER as unlocked")
and commit 08565552f7 ("cputlb: Move NOTDIRTY handling from I/O
path to TLB path").
Remove memory_region_clear_global_locking() and the now unused
'global_locking' field in MemoryRegion.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200806150726.962-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the function that will compute a relocated version of the
directories in CONFIG_QEMU_*DIR and CONFIG_QEMU_*PATH.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just return the directory without requiring the caller to free it.
This also removes a bogus check for NULL in os_find_datadir and
module_load_one; g_strdup of a static variable cannot return NULL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several important steps during device scan depend on SCSI type of the
device. For example, max_transfer property is only determined and
assigned if the device has the type of TYPE_DISK.
Host-managed ZBC disks retain most of the properties of regular SCSI
drives, but they have their own SCSI device type, 0x14. This prevents
the proper assignment of max_transfer property for HM-zoned devices in
scsi-generic driver leading to I/O errors if the maximum i/o size
calculated at the guest exceeds the host value.
To fix this, define TYPE_ZBC to have the standard value from SCSI ZBC
standard spec. Several scan steps that were previously done only for
TYPE_DISK devices, are now performed for the SCSI devices having
TYPE_ZBC too.
Reported-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200811225122.17342-3-dmitry.fomichev@wdc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the "wakeup" property introduced in commit 9826fd597d
("suspend: make serial ports wakeup the guest") a boolean.
As we want to reuse the generic serial properties in the
ISA model (next commit), expose this property.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200907015535.827885-6-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
TYPE_SERIAL_IO is a subset of TYPE_SERIAL_MM, and it is
not used anymore. Remove it.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200907011538.818996-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
it was deprecated since 4.1
commit 4bb4a2732e (numa: deprecate implict memory distribution between nodes)
Users of existing VMs, wishing to preserve the same RAM distribution,
should configure it explicitly using ``-numa node,memdev`` options.
Current RAM distribution can be retrieved using HMP command
`info numa` and if separate memory devices (pc|nv-dimm) are present
use `info memory-device` and subtract device memory from output of
`info numa`.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200911084410.788171-2-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu will send GET_INFLIGHT_FD and SET_INFLIGH_FD to backend, and
the backend setup the inflight memory to track the io.
Change-Id: I805d6189996f7a1b44c65f0b12ef7473b1789510
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200909122021.1055174-1-fengli@smartx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the existing documentation comments of
IOMMUMemoryRegionClass to kernel-doc format so their contents
will appear in the API reference at docs/devel/memory.html.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200908201129.3407568-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Extracting the ACPI commands to their own schema reduces the size of
the qapi-misc* headers generated, and pulls less QAPI-generated code
into user-mode.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-8-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Restricting the memory commands to machine.json pulls less
QAPI-generated code into user-mode.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-7-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Only qemu-system-FOO and qemu-storage-daemon provide QMP
monitors, therefore such declarations and definitions are
irrelevant for user-mode emulation.
Restricting the balloon-related commands to machine.json pulls less
QAPI-generated code into user-mode.
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-4-philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Restricting LostTickPolicy to machine.json pulls slightly less
QAPI-generated code into user-mode.
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200913195348.1064154-2-philmd@redhat.com>
[Add rationale to commit message]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
With upcoming Spice server version 0.14.4, the monitor configuration can
contain additional fields for the monitor physical dimensions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200927145751.365446-6-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The following patch is going to introduce extra fields / details to
UIInfo. Add a getter and keep the current values, instead of memset(0)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200927145751.365446-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace dpi with width_mm/height_mm in qemu_edid_info.
Use it when set (non-zero) to compute the DPI and generate the EDID.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20200927145751.365446-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When CPU hotplug with SMI has been negotiated, describe the SMI
register block in the DSDT. Pass the ACPI name of the SMI control
register to build_cpus_aml(), so that CPU_SCAN_METHOD can access the
register in the next patch.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Expose the "smi_negotiated_features" field of ICH9LPCState as
a QOM property.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow firmware to notify QEMU that firmware requires SMI
being triggered on CPU hot[un]plug, so that it would be able to account
for hotplugged CPU and relocate it to new SMM base and/or safely remove
CPU on unplug.
Using negotiated features, follow up patches will insert SMI upcall
into AML code, to make sure that firmware processes hotplug before
guest OS would attempt to use new CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 9b3a35ec82 ("virtio: verify that legacy support is not accidentally
on") added a check that returns an error if legacy support is on, but the
device does not support legacy.
Unfortunately some devices were wrongly declared legacy capable even if
they were not (e.g vhost-vsock).
To avoid migration issues, we add a virtio-device property
(x-disable-legacy-check) to skip the legacy error, printing a warning
instead, for machine types < 5.1.
Cc: qemu-stable@nongnu.org
Fixes: 9b3a35ec82 ("virtio: verify that legacy support is not accidentally on")
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200921122506.82515-2-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Dumping one line of hexadecimal/ASCII from a buffer is often needed.
Move this part from qemu_hexdump() and use it
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200925091055.186023-2-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These were deprecated since 4.0, remove both HMP and QMP variants.
Users should use device_add command instead. To get list of
possible CPUs and options, use 'info hotpluggable-cpus' HMP
or query-hotpluggable-cpus QMP command.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200915120403.1074579-1-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user devices can get a disconnect in the middle of the VHOST-USER
handshake on the migration start. If disconnect event happened right
before sending next VHOST-USER command, then the vhost_dev_set_log()
call in the vhost_migration_log() function will return error. This error
will lead to the assert() and close the QEMU migration source process.
For the vhost-user devices the disconnect event should not break the
migration process, because:
- the device will be in the stopped state, so it will not be changed
during migration
- if reconnect will be made the migration log will be reinitialized as
part of reconnect/init process:
#0 vhost_log_global_start (listener=0x563989cf7be0)
at hw/virtio/vhost.c:920
#1 0x000056398603d8bc in listener_add_address_space (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2664
#2 0x000056398603dd30 in memory_listener_register (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2740
#3 0x0000563985fd6956 in vhost_dev_init (hdev=0x563989cf7bd8,
opaque=0x563989cf7e30, backend_type=VHOST_BACKEND_TYPE_USER,
busyloop_timeout=0)
at hw/virtio/vhost.c:1385
#4 0x0000563985f7d0b8 in vhost_user_blk_connect (dev=0x563989cf7990)
at hw/block/vhost-user-blk.c:315
#5 0x0000563985f7d3f6 in vhost_user_blk_event (opaque=0x563989cf7990,
event=CHR_EVENT_OPENED)
at hw/block/vhost-user-blk.c:379
Update the vhost-user-blk device with the internal started_vu field which
will be used for initialization (vhost_user_blk_start) and clean up
(vhost_user_blk_stop). This additional flag in the VhostUserBlk structure
will be used to track whether the device really needs to be stopped and
cleaned up on a vhost-user level.
The disconnect event will set the overall VHOST device (not vhost-user) to
the stopped state, so it can be used by the general vhost_migration_log
routine.
Such approach could be propogated to the other vhost-user devices, but
better idea is just to make the same connect/disconnect code for all the
vhost-user devices.
This migration issue was slightly discussed earlier:
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg01509.html
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg05241.html
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <9fbfba06791a87813fcee3e2315f0b904cc6789a.1599813294.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To speed up the memory mapping updating between vhost-vDPA and vDPA
device driver, this patch passes the IOTLB batching flags via IOTLB
API. Two new flags was introduced, VHOST_IOTLB_BATCH_BEGIN is a hint
that a bathced IOTLB updating may be initiated from the
userspace. VHOST_IOTLB_BATCH_END is a hint that userspace has finished
the updating:
VHOST_IOTLB_BATCH_BEGIN
VHOST_IOTLB_UPDATE/VHOST_IOTLB_INVALIDATE
...
VHOST_IOTLB_BATCH_END
Vhost-vDPA can then know that all mappings has been set and can do
optimization like passing all the mappings to the vDPA device driver.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-4-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch tries to switch to use new kernel IOTLB format V2. Previous
version may have inconsistent ABI between 32bit and 64bit machines
because of the hole after type field. Refer kernel commit
("429711aec282 vhost: switch to use new message format") for more
information.
To enable this feature, qemu need to use a new ioctl
VHOST_SET_BACKEND_FEATURE with VHOST_BACKEND_F_IOTLB_MSG_V2 bit. A new
vhost setting backend features ops was introduced. And when we try to
set features for vhost dev, we will examine the support of new IOTLB
format and enable it. This process is total transparent to guest,
which means we can have different IOTLB message type in src and dst
during migration.
The conversion of IOTLB message is straightforward, just check the
type and behave accordingly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-3-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Update against Linux 5.9-rc4.
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200907104903.31551-2-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
