With the pc-q35-2.4 machine type, if the user creates an ISA FDC manually:
-device isa-fdc,driveA=drive-fdc0-0-0 \
-drive file=...,if=none,id=drive-fdc0-0-0,format=raw
then the board-default FDC will be skipped, and only the explicitly
requested FDC will exist. qtree-wise, this is correct; however such an FDC
is currently not registered in the CMOS, because that code is only reached
for the board-default FDC.
The pc_cmos_init_late() one-shot reset handler -- one-shot because the
CMOS is not reprogrammed during warm reset -- should search for any ISA
FDC devices, created implicitly (by board code) or explicitly, and set the
CMOS accordingly to the ISA FDC(s) with iobase=0x3f0:
- if there is no such FDC, report both drives absent,
- if there is exactly one such FDC, report its drives in the CMOS,
- if there are more than one such FDCs, then pick one (it is not specified
which one), and print a warning about the ambiguity.
Cc: Jan Tomko <jtomko@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Jan Tomko <jtomko@redhat.com>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract the pc_cmos_init_floppy() function from pc_cmos_init(). The
function sets two RTC registers: floppy drive types (0x10), overwriting
the earlier value in there), and REG_EQUIPMENT_BYTE (0x14), setting bits
in the prior value.
Cc: Jan Tomko <jtomko@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If the signal is sampled high, this indicates that the system is
strapped to the "No Reboot" mode (ICH9 will disable the TCO Timer system
reboot feature). The status of this strap is readable via the NO_REBOOT
bit (CC: offset 0x3410:bit 5).
The NO_REBOOT bit is set when SPKR pin on ICH9 is sampled high. This bit
may be set or cleared by software if the strap is sampled low but may
not override the strap when it indicates "No Reboot".
This patch implements the logic where hardware has ability to set SPKR
pin through a property named "noreboot" and it's sampled high by
default.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A few last minute PPC changes for 2.4:
- spapr: Update SLOF
- spapr: Fix a few bugs
- spapr: Preparation for hotplug
- spapr: Minor code cleanups
- linux-user: Add mftb handling
- kvm: Enable hugepage support with memory-backend-file
- mac99: Remove nonexistent interrupt pin (Mac OS 9 fix)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJVm/TZAAoJECszeR4D/txg0rUP/R1C5IAuY0vM7LOYRbp1jFmn
EO6AZpJaXvT2xP0wUd/rqJct/O41vDVbEmnhpUAQwZcgsyw1UaKhRQbnCtY9PHD2
d7NZiBdv3AAbh8pLFadRjDJr/HrfuWVfjKKep5cM87/o3zjVreeIX8Hs77xHia6/
90n3hcDF4QL8qx6fxCMT4mGpTtbxw85IcK2wyIU45cZSN0VYaTjDwcYokeSKqgxV
pi7UjZSM5nZcn7VI1Uray4NkgXGs92Lorrbg08OFQt0AoXROJOk4V/LX3HkHfDbI
BYUgaOQNdBkytkB3fJCsTgl2Up82bVP/tghMyZOIyBAU4MslnAOW6HAMX2TtNswx
7itnIb7DQsVDE/U234Xzf5qoH5x4nB9xKh2qLHPKSpgLChs6lAW37Af3N+V03JVb
k/WX6i0n70a6kUqCxcMTnVSINWandU2jdJ/S8woIqs6XhfLk7hh0ucg+VhgoQxW7
QpeD69c25eVHeZDoMKR/ZTigJg/EQGuV9B9OSx6SyA9WMS4dImt1m0PBdaUlIAFT
759lMMwQIb5sQYghJ63tgrOI5PBneGnelM1zDWt2SCS0rbSjLWIWP47pHoNmnzzp
vIhJX5GgVuzf0NrbZPSR7/6NuKKU6UW5CTGh3vFgRib/CWIbEgCE3yWQfflZKy5q
Q2xBuAjyWnBoipzI4hlz
=+Uma
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2015-07-07
A few last minute PPC changes for 2.4:
- spapr: Update SLOF
- spapr: Fix a few bugs
- spapr: Preparation for hotplug
- spapr: Minor code cleanups
- linux-user: Add mftb handling
- kvm: Enable hugepage support with memory-backend-file
- mac99: Remove nonexistent interrupt pin (Mac OS 9 fix)
# gpg: Signature made Tue Jul 7 16:48:41 2015 BST using RSA key ID 03FEDC60
# gpg: Good signature from "Alexander Graf <agraf@suse.de>"
# gpg: aka "Alexander Graf <alex@csgraf.de>"
* remotes/agraf/tags/signed-ppc-for-upstream: (30 commits)
sPAPR: Clear stale MSIx table during EEH reset
sPAPR: Reenable EEH functionality on reboot
sPAPR: Don't enable EEH on emulated PCI devices
spapr-vty: Use TYPE_ definition instead of hardcoding
spapr_vty: lookup should only return valid VTY objects
spapr_pci: drop redundant args in spapr_[populate, create]_pci_child_dt
spapr_pci: populate ibm,loc-code
spapr_pci: enumerate and add PCI device tree
xics_kvm: Don't enable KVM_CAP_IRQ_XICS if already enabled
ppc: Update cpu_model in MachineState
spapr: Consolidate cpu init code into a routine
spapr: Reorganize CPU dt generation code
cpus: Add a macro to walk CPUs in reverse
spapr: Support ibm, lrdr-capacity device tree property
spapr: Consider max_cpus during xics initialization
Revert "hw/ppc/spapr_pci.c: Avoid functions not in glib 2.12 (g_hash_table_iter_*)"
spapr_iommu: translate sPAPRTCEAccess to IOMMUAccessFlags
spapr_iommu: drop erroneous check in h_put_tce_indirect()
spapr_pci: set device node unit address as hex
spapr_pci: encode class code including Prog IF register
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ksVw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20150707' into staging
migration/next for 20150707
# gpg: Signature made Tue Jul 7 13:56:30 2015 BST using RSA key ID 5872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
* remotes/juanquintela/tags/migration/20150707: (28 commits)
migration: extend migration_bitmap
migration: protect migration_bitmap
check_section_footers: Check the correct section_id
migration: Add migration events on target side
migration: Make events a capability
migration: create migration event
migration: No need to call trace_migrate_set_state()
migration: Use always helper to set state
migration: ensure we start in NONE state
migration: Use cmpxchg correctly
migration: Add configuration section
vmstate: Create optional sections
global_state: Make section optional
migration: create new section to store global state
runstate: migration allows more transitions now
runstate: Add runstate store
Fix older machine type compatibility on power with section footers
Fail more cleanly in mismatched RAM cases
Sanity check RDMA remote data
Sort destination RAMBlocks to be the same as the source
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PCI device MSIx table is cleaned out in hardware after EEH PE
reset. However, we still hold the stale MSIx entries in QEMU, which
should be cleared accordingly. Otherwise, we will run into another
(recursive) EEH error and the PCI devices contained in the PE have
to be offlined exceptionally.
The patch introduces function spapr_phb_vfio_eeh_pre_reset(), which
is called by sPAPR when asserting hot or fundamental reset, to clear
stale MSIx table for VFIO PCI devices before EEH PE reset so that
MSIx table could be restored properly after EEH PE reset.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
When rebooting the guest, some PEs might be in frozen state. The
contained PCI devices won't work properly if their frozen states
aren't cleared in time. One case running into this situation would
be maximal EEH error times encountered in the guest.
The patch reenables the EEH functinality on PEs on PHB's reset
callback, which will clear their frozen states if needed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
There might have emulated PCI devices, together with VFIO PCI
devices under one PHB. The EEH capability shouldn't enabled
on emulated PCI devices.
The patch returns error when enabling EEH capability on emulated
PCI devices by RTAS call "ibm,set-eeh-option".
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
There's a call to object_dynamic_cast() in spapr_vty which uses the type
name "spapr-vty" directly, instead of the usual idiom of using the #defined
TYPE_VIO_SPAPR_VTY_DEVICE. Fix it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a guest passes the reg property of a valid VIO object that is not a VTY
to either H_GET_TERM_CHAR or H_PUT_TERM_CHAR, QEMU hits a dynamic cast
assertion and aborts.
PAPR+ says "Hypervisor checks the termno parameter for validity against the
Vterm IOA unit addresses assigned to the partition, else return H_Parameter."
This patch adds a type check to ensure vty_lookup() either returns a pointer
to a valid VTY object or NULL. H_GET_TERM_CHAR and H_PUT_TERM_CHAR will
now return H_PARAMETER to the guest instead of crashing.
The patch has no effect on the reg == 0 hack used to implement the RTAS call
display-character.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
* phb_index is not being used and if required can be obtained from sphb
* use helper to get drc_index in spapr_populate_pci_child_dt()
* Check if drc_index is zero
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Each hardware instance has a platform unique location code. The OF
device tree that describes a part of a hardware entity must include
the “ibm,loc-code” property with a value that represents the location
code for that hardware entity.
Populate ibm,loc-code.
1) PCI passthru devices need to identify with its own ibm,loc-code
available on the host. In failure cases use:
vfio_<name>:<phb-index>:<bus>:<slot>.<fn>
2) Emulated devices encode as following:
qemu_<name>:<phb-index>:<bus>:<slot>.<fn>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
All the PCI enumeration and device node creation was off-loaded to
SLOF. With PCI hotplug support, code needed to be added to add device
node. This creates multiple copy of the code one in SLOF and other in
hotplug code. To unify this, the patch adds the pci device node
creation in Qemu. For backward compatibility, a flag
"qemu,phb-enumerated" is added to the phb, suggesting to SLOF to not
do device node creation.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ Squashed Michael's drc_index changes ]
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
When supporting CPU hot removal by parking the vCPU fd and reusing
it during hotplug again, there can be cases where we try to reenable
KVM_CAP_IRQ_XICS CAP for the vCPU for which it was already enabled.
Introduce a boolean member in ICPState to track this and don't
reenable the CAP if it was already enabled earlier.
Re-enabling this CAP should ideally work, but currently it results in
kernel trying to create and associate ICP with this vCPU and that
fails since there is already an ICP associated with it. Hence this
patch is needed to work around this problem in the kernel.
This change allows CPU hot removal to work for sPAPR.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Keep cpu_model field in MachineState uptodate so that it can be used
from the CPU hotplug path.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Factor out bits of sPAPR specific CPU initialization code into
a separate routine so that it can be called from CPU hotplug
path too.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reorganize CPU device tree generation code so that it be reused from
hotplug path. CPU dt entries are now generated from spapr_finalize_fdt()
instead of spapr_create_fdt_skel().
Note: This is how the split-up looks like now:
Boot path
---------
spapr_finalize_fdt
spapr_populate_cpus_dt_node
spapr_populate_cpu_dt
spapr_fixup_cpu_numa_dt
spapr_fixup_cpu_smt_dt
ibm,cas path
------------
spapr_h_cas_compose_response
spapr_fixup_cpu_dt
spapr_fixup_cpu_numa_dt
spapr_fixup_cpu_smt_dt
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for ibm,lrdr-capacity since this is needed by the guest
kernel to know about the possible hot-pluggable CPUs and Memory. With
this, pseries kernels will start reporting correct maxcpus in
/sys/devices/system/cpu/possible.
Also define the minimum hotpluggable memory size as 256MB.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[agraf: Fix compile error on 32bit hosts]
Signed-off-by: Alexander Graf <agraf@suse.de>
Use max_cpus instead of smp_cpus when intializating xics system. Also
report max_cpus in ibm,interrupt-server-ranges device tree property of
interrupt controller node.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since we now require GLib 2.22+ (commit f40685c), we don't have to
work around lack of g_hash_table_iter_init() & friends anymore.
This reverts commit f8833a37c0.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The fact that these enums have matching values is pure coincidence. We
actually need to translate from the PAPR definition to the QEMU one.
This patch doesn't fix any bug, it is only code cleanup.
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The tce_list variable is not a TCE but the address to a TCE: we shouldn't
clear permission bits as we do now. And this is dead code anyway since we
check tce_list is 4K aligned a few lines above.
This patch doesn't fix any bug, it is only code cleanup.
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Device node names should encode the unit address as hex, while the
code was encodind it as integers.
Also, use FDT_NAME_MAX macro for allocating and composing the name.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Current code missed the Prog IF register. All Class Code, Subclass,
and Prog IF registers are needed to identify the accurate device type.
For example: USB controllers use the PROG IF for denoting: USB
FullSpeed, HighSpeed or SuperSpeed.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The properties reg/assigned-resources need to encode 64-bit memory
address space as part of phys.hi dword.
00 if configuration space
01 if IO region,
10 if 32-bit MEM region
11 if 64-bit MEM region
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently although we have an sPAPRMachineState descended from MachineState
we don't have an sPAPRMAchineClass descended from MachineClass. So far it
hasn't been needed, but several upcoming features are going to want it,
so this patch creates a stub implementation.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The sPAPRMachineState structure includes an entry_point field containing
the initial PC value for starting the machine, even though this always has
the value 0x100.
I think this is a hangover from very early versions which bypassed the
firmware when using -kernel. In any case it has no function now, so remove
it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The ram_limit field was imported from sPAPREnvironment where it predates
the machine's ram size being available generically from machine->ram_size.
Worse, the existing code was inconsistent about where it got the ram size
from. Sometimes it used spapr->ram_limit, sometimes the global 'ram_size'
and sometimes a local 'ram_size' masking the global.
This cleans up the code to consistently use machine->ram_size, eliminating
spapr->ram_limit in the process.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code for -machine pseries maintains a global sPAPREnvironment structure
which keeps track of general state information about the guest platform.
This predates the existence of the MachineState structure, but performs
basically the same function.
Now that we have the generic MachineState, fold sPAPREnvironment into
sPAPRMachineState, the pseries specific subclass of MachineState.
This is mostly a matter of search and replace, although a few places which
relied on the global spapr variable are changed to find the structure via
qdev_get_machine().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
XICS needs to know the upper value for cpu_index as it is used to compute
the number of servers:
smp_cpus * kvmppc_smt_threads() / smp_threads
When passing -smp cpus=1,threads=9 on a POWER8 host, we end up with:
1 * 8 / 9 = 0
... which leads to an assertion in both emulated:
Number of servers needs to be greater 0
Aborted (core dumped)
... and in-kernel XICS:
xics_kvm_realize: Assertion `icp->nr_servers' failed.
Aborted (core dumped)
With this patch, we are sure that nr_servers > 0. Passing the same bogus
-smp option then leads to:
qemu-system-ppc64: Cannot support more than 8 threads on PPC with KVM
... which is a lot more explicit than the XICS errors.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current macio implementation declares an interrupt that doesn't appear to
exist in the hardware or any other emulator implementation. OpenBIOS detects
this interrupt and generates an 'interrupts' property in the macio device tree
entry. Mac OS 9 halts boot when it detects this interrupt, so it has been
removed to permit further progress in the boot process.
Signed-off-by: Cormac O'Brien <i.am.cormac.obrien@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alexander Graf <agraf@suse.de>
It needs to be the first one and it is not optional, that is the reason
why it is opencoded. For new machine types, it is required that machine
type name is the same in both sides.
It is just done right now for pc's.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This section would be sent:
a- for all new machine types
b- for old machine types if section state is different form {running,paused}
that were the only giving us troubles.
So, in new qemus: it is alwasy there. In old qemus: they are only
there if it an error has happened, basically stoping on target.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
I forgot to add compatibility for Power when adding section footers.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: 37fb569c01
Signed-off-by: Juan Quintela <quintela@redhat.com>
For pkts copied to the CPU (to be processed by guest driver), mark the Rx
descriptor with flag "OFFLOAD_FWD" to indicate device has already forwarded
pkt. The guest driver will use this indicator to avoid duplicate
forwarding in the guest OS.
Examples include bcast/mcast/unknown ucast pkts flooded to bridged ports.
We want to avoid both the device and the guest bridge driver flooding these
pkts, which would result in duplicates pkts on the wire. Packet sampling,
such as sFlow, can also use this technique to mark pkts for the guest OS to
record but otherwise drop.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Message-id: 1435746792-41278-5-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435746792-41278-3-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Premature break in switch case block. This particular case (group L2 rewrite)
will be used for L2 LAG and L3 ECMP support, neither of which are enabled in
the guest driver at this time, but are under development.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435746792-41278-2-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 6e99c63 ("net/socket: Drop net_socket_can_send") changed the
semantics around .can_receive for sockets to now require the device to
flush queued pkts when transitioning to a .can_receive=true state. Rocker
device was not flushing the queue on .can_receive=true transition, so the
receiver was stuck.
But, turns out we really don't want any queuing at all on the port when the
port is disabled, otherwise when the port transitions to enabled, we'd
receive and forward stale pkts that really should have been dropped. So,
let's remove .can_receive so avoid queuing and drop the pkt in .receive if
the port is disabled.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1435717553-36187-1-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When running ESXi under qemu there is an issue with the ESXi guest
discarding packets that are too short. The guest discards any packets
under the normal minimum length for an ethernet packet (60). This
results in odd behaviour where other hosts or VMs on other hosts can
communicate with the ESXi guest just fine (since there's a physical NIC
somewhere doing padding), but VMs on the host and the host itself cannot
because the ARP request packets are too small for the ESXi host to
accept.
Someone in the past thought this was worth fixing, and added code to the
vmxnet3 qemu emulation such that if it is receiving packets smaller than
60 bytes to pad the packet out to 60. Unfortunately this code is wrong
(or at least in the wrong place). It does so BEFORE before taking into
account the vnet_hdr at the front of the packet added by the tap device.
As a result, it might add padding, but it never adds enough.
Specifically it adds 10 less (the length of the vnet_hdr) than it needs
to.
The following (hopefully "obviously correct") patch simply swaps the
order of processing the vnet header and the padding. With this patch an
ESXi guest is able to communicate with the host or other local VMs.
Signed-off-by: Brian Kress <kressb@moose.net>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
e1000_can_receive() checks the link up status register bit. If the bit
is clear, packets will be queued and the peer may disable receive to
avoid wasting CPU reading packets that cannot be delivered. The queue
must be flushed once the link comes back up again.
This patch fixes broken e1000 receive with Mac OS X Snow Leopard guests
and tap networking. Flushing the queue invokes the async send callback,
which re-enables tap fd read.
Reported-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1435223885-12745-1-git-send-email-stefanha@redhat.com
This interface provides some registers within a 32-byte range and can be
acessed through PCI-to-LPC bridge interface (PMBASE + 0x60).
It's commonly used as a watchdog timer to detect system lockups through
SMIs that are generated -- if TCO_EN bit is set -- on every timeout. If
NO_REBOOT bit is not set in GCS (General Control and Status register),
the system will be resetted upon second timeout if TCO_RLD register
wasn't previously written to prevent timeout.
This patch adds support to TCO watchdog logic and few other features
like mapping NMIs to SMIs (NMI2SMI_EN bit), system intruder detection,
etc. are not implemented yet.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MIPS doesn't need it, and including it creates problem as we are adding
dependency on ISA LPC bridge.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch over to virtio_instance_init_common. Drop duplicate properties
in virtio-gpu-pci and virtio-vga as they are properly aliased now. Also
drop the indirection via DEFINE_VIRTIO_GPU_PROPERTIES, we don't need it
any more as the properties are defined in a single place now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Update the device link of the QemuConsole, so it points to the
virtio-gpu-pci or virtio-vga device instead of virtio-gpu-device.
This is needed because we want to find the device by id, for
example for input routing, and the id specified on the command
line is attached to the pci proxy, not the virtio device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On ARM, commit ac9d32e396 postponed the
memory preparation for boot until the machine init done notifier. This
has for consequence to insert ROM at machine init done time.
However the rom_load_all function stayed called before the ROM are
inserted. As a consequence the rom_load_all function does not do
everything it is expected to do, on ARM.
It currently registers the ROM reset notifier but does not iterate through
the registered ROM list. the isrom field is not set properly. This latter
is used to report info in the monitor and also to decide whether the
rom->data can be freed on ROM reset notifier.
To fix that regression the patch moves the rom_load_all call after
machine init done. We also take the opportunity to rename the rom_load_all
function into rom_check_and_resgister_reset() and integrate the
rom_load_done in it.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reported-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-Id: <1434470874-22573-1-git-send-email-eric.auger@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit f5a5628cf0.
This was an old patch that had been already superseded by b0e5d90eb
("dataplane: endianness-aware accesses").
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Accesses to vring_avail_event and vring_used_event must honor the queue
endianness.
This patch allows cross-endian setups to use dataplane (tested with ppc64
on ppc64le, and vice-versa).
Suggested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Fix pba_offset initialization value for Chelsio T5 Virtual Function
device. The T5 hardware has a bug in it where it reports a Pending Interrupt
Bit Array Offset of 0x8000 for its SR-IOV Virtual Functions instead
of the 0x1000 that the hardware actually uses internally. As the hardware
doesn't return the correct pba_offset value, add a quirk to instead
return a hardcoded value of 0x1000 when a Chelsio T5 VF device is
detected.
This bug has been fixed in the Chelsio's next chip series T6 but there are
no plans to respin the T5 ASIC for this bug. It is just documented in the
T5 Errata and left it at that.
Signed-off-by: Gabriel Laupre <glaupre@chelsio.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On systems with guest visible IOMMU, adding a new memory region onto
PCI bus calls vfio_listener_region_add() for every DMA window. This
installs a notifier for IOMMU memory regions. The notifier is supposed
to be removed vfio_listener_region_del(), however in the case of mixed
PHB (emulated + VFIO devices) when last VFIO device is unplugged and
container gets destroyed, all existing DMA windows stay alive altogether
with the notifiers which are on the linked list which head was in
the destroyed container.
This unregisters IOMMU memory region notifier when a container is
destroyed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch aims at optimizing IRQ handling using irqfd framework.
Instead of handling the eventfds on user-side they are handled on
kernel side using
- the KVM irqfd framework,
- the VFIO driver virqfd framework.
the virtual IRQ completion is trapped at interrupt controller
This removes the need for fast/slow path swap.
Overall this brings significant performance improvements.
Signed-off-by: Alvise Rigo <a.rigo@virtualopensystems.com>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add a new connect_irq_notifier notifier in the SysBusDeviceClass. This
notifier, if populated, is called after sysbus_connect_irq.
This mechanism is used to setup VFIO signaling once VFIO platform
devices get attached to their platform bus, on a machine init done
notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The arm_gic_kvm now calls kvm_irqchip_set_qemuirq_gsi to build
the hash table storing qemu_irq/gsi mappings. From that point on
irqfd can be setup directly from the qemu_irq using
kvm_irqchip_add_irqfd_notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Anticipating for the introduction of new add/remove functions taking
a qemu_irq parameter, let's rename existing ones with a gsi suffix.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is system level code, and should only depend on the host page
size, not the target page size.
Note that HOST_PAGE_SIZE is misleadingly lead and is really aligning
to both host and target page size. Hence it's replacement with
REAL_HOST_PAGE_SIZE.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
size_t is an unsigned type, thus the error case is never reached in
the below call to pread. If bytes is negative, it will be seen as
a very high positive value.
Spotted by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The property can take values on, off or auto. The default is "off"
for KVM and pre-2.4 machines, otherwise "auto" (which makes it
available on TCG or on new-enough kernels).
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Q35's ACPI device is hard-coding SMM availability to KVM. Place the
logic where the board is created instead, so that it will be possible
to override it.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will enable SMM even if KVM is in use. Rename the field and
arguments.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These commands are handled entirely by QEMU. Do not raise an SMI
when they happen, because Windows (at least 2008r2) expects these
commands to work and (depending on the value of APMC_EN at
startup) the firmware might not have installed an SMI handler.
When this happens (e.g. the kernel supports SMIs, or you are using
TCG, but you have used "-machine smm=off") RIP is moved to 0x38000
where there is no code to execute.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* unlocked MMIO support in KVM
* support for compilation with ICC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVmnuoAAoJEL/70l94x66DKTUH/RFrc20KXRkn/Pb/8qHY/wFz
Wt3YaS5VYPHElHbxHSdpwlV3K50FAX4QaC25Dnw4dsTelyxe5k7od+I7x8PQxD9v
3N+mFFF1BV6PqXTPVnUCnb14EXprJX524E97O6Z3lDGcwSLHDxeveSCk3IvMFErz
JzP3vtigSvtdPPQXlGcndP/r1EXeVjgNIsZ+NKaI/kmoSz1fHFrCN8hTnrxA9RSI
ZPhfmgHI5EMFtAf/HiZID6GSHOHajgeRT2bIiiy1okS++no0uRZlVMvcnFNPZHoG
e9XCGBXJSdmCoi7sIgShXirKszxYkRTbCyxxjz6aYfhrQzo0h+Yn9OPuvQrgynE=
=+YEv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* more of Peter Crosthwaite's multiarch preparation patches
* unlocked MMIO support in KVM
* support for compilation with ICC
# gpg: Signature made Mon Jul 6 13:59:20 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
exec: skip MMIO regions correctly in cpu_physical_memory_write_rom_internal
Stop including qemu-common.h in memory.h
kvm: Switch to unlocked MMIO
acpi: mark PMTIMER as unlocked
kvm: Switch to unlocked PIO
kvm: First step to push iothread lock out of inner run loop
memory: let address_space_rw/ld*/st* run outside the BQL
exec: pull qemu_flush_coalesced_mmio_buffer() into address_space_rw/ld*/st*
memory: Add global-locking property to memory regions
main-loop: introduce qemu_mutex_iothread_locked
main-loop: use qemu_mutex_lock_iothread consistently
Fix irq route entries exceeding KVM_MAX_IRQ_ROUTES
cpu-defs: Move out TB_JMP defines
include/exec: Move tb hash functions out
include/exec: Move standard exceptions to cpu-all.h
cpu-defs: Move CPU_TEMP_BUF_NLONGS to tcg
memory_mapping: Rework cpu related includes
cutils: allow compilation with icc
qemu-common: add VEC_OR macro
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timer should fire the interrupt only if the IT (interrupt enable) bit
state of the control register is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The running timer can't be stopped because timer control code just
doesn't handle disabling the timer. Fix it by deleting the timer if
the enable bit is cleared.
The timer won't start periodic ticking if a ONE-SHOT -> PERIODIC mode
change happens after a one-shot tick was completed. Fix it by
re-starting ticking if the timer isn't ticking right now.
To avoid code churning, these two fixes are squashed in one commit.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
The interval interrupt is not set if the timer is in decrement mode.
This is because x >=0 and x < interval after leaving the while-loop.
Signed-off-by: Johannes Schlatow <schlatow@ida.ing.tu-bs.de>
Message-id: 20150630135821.51f3b4fd@johanness-latitude
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQIcBAABAgAGBQJVl3fQAAoJEH3vgQaq/DkOgNkP/0gkVzBeIhuJHEWJasX12zS4
VaXAKNc/haSvnT4nOOw2VfvyXvbawUgN1izBKhqrGu+Qdj9kZXMuQN/H8V7kLQeK
s9/c9FmiI4On9uheol294Ig9Q8R/NUc9Z69st0usEdAIlGOhzQlItwzQQecDWmd6
LIb0pVAId4jrW+bW5XbMEzCSKQkD5ETKAZ8cMh1+U60b8Oi0xZsY/q+SPhj/PHrX
vH98oOVT0rgQ9ZJPpSmxa2SpeeMINkROeer19rJY9tbcK4W52i4yt7c0NxhICYfP
bB75Zis0TUR9csuuW2801bejxhNhwDka5vur6q14h4wEawtPMV07zhmxTVyKFk89
Y1Jzt7ys2awotHy6/XrHU4eUBwpd1BAgZ8P5M0HzKdxH6+Xxg269zc/QmG3FqCVo
HKJ7e/vcmImYJZG1GhJrP4PUfXrLOciBzYhmaxwGNQLXrM1YUE6F/PvgIJyRGRdB
vXrFUifxHylgQUAdlHHAqT4LlfJZVjTVBVntGqoZgH7RiyK4lSmyUkdYRtlG+Fcm
SCCjRcCAh1nzSp7XI2QziNl/ezavOI4lpAv64ubXU3VGxudGgcq+WsYF4iEOdbNJ
W04QVCjR9PzvLabRLYzTtWTywYT79cg4xh/Lq+EyXAoWFRM2/CYliHJk4VSlk3Us
v8a6sWB9qc3dq6f6uUTX
=nQZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into staging
# gpg: Signature made Sat Jul 4 07:06:08 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB
# Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E
* remotes/jnsnow/tags/ide-pull-request: (35 commits)
ahci: fix sdb fis semantics
qtest/ahci: halted ncq migration test
ahci: Do not map cmd_fis to generate response
ahci: ncq migration
ahci: add get_cmd_header helper
ahci: add cmd header to ncq transfer state
qtest/ahci: halted NCQ test
ahci: correct ncq sector count
ahci: correct types in NCQTransferState
ahci: add rwerror=stop support for ncq
ahci: factor ncq_finish out of ncq_cb
ahci: refactor process_ncq_command
ahci: assert is_ncq for process_ncq
ahci: stash ncq command
ide: add limit to .prepare_buf()
qtest/ahci: ncq migration test
qtest/ahci: simple ncq data test
libqos/ahci: Force all NCQ commands to be LBA48
libqos/ahci: set the NCQ tag on command_commit
libqos/ahci: adjust expected NCQ interrupts
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are two things to fix here:
The first one is subtle: the PxSACT register in the AHCI HBA has different
semantics from the field it is shadowing, the ACT field in the
Set Device Bits FIS.
In the HBA register, PxSACT acts as a bitfield indicating outstanding
NCQ commands where a set bit indicates a pending NCQ operation. The FIS
field however operates as an RWC register update to PxSACT, where a set
bit indicates a *successfully* completed command.
Correct the FIS semantics. At the same time, move the "clear finished"
action to the SDB FIS generation instead of the register read to mimick
how the other shadow registers work, which always just report the last
reported value from a FIS, and not the most current values which may
not have been reported by a FIS yet.
Lastly and more simply, SATA 3.2 section 13.6.4.2 (and later sections)
all specify that the Interrupt bit for the SDB FIS should always be set
to one for NCQ commands. That's currently the only time we generate this
FIS, so set it on all the time.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-16-git-send-email-jsnow@redhat.com
The Register D2H FIS should copy the current values of
the registers instead of just parroting back the same
values the guest sent back to it.
In this case, the SECTOR COUNT variables are actually
not generally meaningful in terms of standard commands
(See ATA8-AC3 Section 9.2 Normal Outputs), so it actually
probably doesn't matter what we put in here.
Meanwhile, we do need to use the Register update FIS from
the NCQ pathways (in error cases), so getting rid of
references to cur_cmd here is a win for AHCI concurrency.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-14-git-send-email-jsnow@redhat.com
Migrate the NCQ queue. This is solely for the benefit of halted commands,
since anything else should have completed and had any relevant status
flushed to the HBA registers already.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-13-git-send-email-jsnow@redhat.com
cur_cmd is an internal bookmark that points to the
current AHCI Command Header being processed by the
AHCI state machine. With NCQ needing to occasionally
rely on some of the same AHCI helpers, we cannot use
cur_cmd and will need to grab explicit pointers instead.
In an attempt to begin relying on the cur_cmd pointer
less, add a helper to let us specifically get the pointer
to the command header of particular interest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-12-git-send-email-jsnow@redhat.com
While the rest of the AHCI device can rely on a single bookmarked
pointer for the AHCI Command Header currently being processed, NCQ
is asynchronous and may have many commands in flight simultaneously.
Add a cmdh pointer to the ncq_tfs object and make the sglist prepare
function take an AHCICmdHeader pointer so we can be explicit about
where we'd like to build SGlists from.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-11-git-send-email-jsnow@redhat.com
uint16_t isn't enough to hold the real sector count, since a value of
zero implies a full 64K sectors, so we need a uint32_t here.
We *could* cheat and pretend that this value is 0-based and fit it in
a uint16_t, but I'd rather waste 2 bytes instead of a future dev's
10 minutes when they forget to +1/-1 accordingly somewhere.
See SATA 3.2, section 13.6.4.1 "READ FPDMA QUEUED".
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-9-git-send-email-jsnow@redhat.com
Handle NCQ failures for cases where we want to halt the VM on IO errors.
Upon a VM state change, retry the halted NCQ commands.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-7-git-send-email-jsnow@redhat.com
When we add werror=stop or rerror=stop support to NCQ,
we'll want to take a codepath where we don't actually
complete the command, so factor that out into a new routine.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-6-git-send-email-jsnow@redhat.com
Split off execute_ncq_command so that we can call
it separately later if we desire.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-5-git-send-email-jsnow@redhat.com
We already checked this in the handle_cmd phase, so just
change this to an assertion and simplify the error logic.
(Also, fix the switch indent, because checkpatch.pl yelled.)
((Sorry for churn.))
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-4-git-send-email-jsnow@redhat.com
For migration and werror=stop/rerror=stop resume purposes,
it will be convenient to have the command handy inside of
ncq_tfs.
Eventually, we'd like to avoid reading from the FIS entirely
after the initial read, so this is a byte (hah!) sized step
in that direction.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-3-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
This value should not be size-corrected, 0 sectors does not imply
1 sector(s). This is just debug information, but it's misleading!
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-8-git-send-email-jsnow@redhat.com
Most of the time, these bits can be safely ignored. For the purposes
of debugging however, it's nice to know that they're not being used.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-7-git-send-email-jsnow@redhat.com
There's no real reason to have it bundled together, and this way
is a little nicer to follow if you have the AHCI spec pulled up.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-6-git-send-email-jsnow@redhat.com
Don't attempt the NCQ transfer if the PRDT we were given is not big
enough to perform the entire transfer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-5-git-send-email-jsnow@redhat.com
Set some appropriate error bits for NCQ for us.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-4-git-send-email-jsnow@redhat.com
Trivial cleanup that I didn't want to tack-on to anything else.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-3-git-send-email-jsnow@redhat.com
Several fields of the NCQFIS structure are ambiguously named. This patch
clarifies the intended (if unsupported) usage of the NCQ fields to aid
in creating more meaningful debug messages through the NCQ codepaths.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-2-git-send-email-jsnow@redhat.com
The only guidance the AHCI specification gives on memory access is:
"Register accesses shall have a maximum size of 64-bits; 64-bit access
must not cross an 8-byte alignment boundary."
I interpret this to mean that aligned or unaligned 1, 2 and 4 byte
accesses should work, as well as aligned 8 byte accesses.
In practice, a real Q35/ICH9 responds to 1, 2, 4 and 8 byte reads
regardless of alignment. Windows 7 can be observed making 1 byte
reads to the middle of 32 bit registers to fetch error codes.
Introduce a wrapper to support unaligned accesses to AHCI.
This wrapper will support aligned 8 byte reads, but will make
no effort to support unaligned 8 byte reads, which although they
will work on real hardware, are not guaranteed to work and do
not appear to be used by either Windows or Linux.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1434470575-21625-2-git-send-email-jsnow@redhat.com
Start storing the (start_addr, end_addr) of the pc-dimm memory
in corresponding numa_info[node] so that this information can be used
to lookup node by address.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
HotplugHandlerClass::plug() shouldn't fail and hence use error_abort
to abort if it fails.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
pc_dimm_plug() has code that will be needed for memory plug handlers
in other archs too. Extract code from pc_dimm_plug() into a generic
routine pc_dimm_memory_plug() that resides in pc-dimm.c. Also
correspondingly refactor re-usable unplug code into pc_dimm_memory_unplug().
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move hotplug_memory_base and hotplug_memory fields of PCMachineState
into a separate structure so that the same can be made use of from
other architectures supporing memory hotplug.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add display and head properties for input routing to
virtio-input devices, update multiseat documentation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The section footer changes commit f68945d42b ("Add a protective
section footer") and commit 37fb569c01 ("Disable section footers
on older machine types") broke migration for any non-versioned
machines.
This pinpoints a problem of s390-ccw machines: it needs to
be versioned to be compatible with future changes in common
code data structures such as section footers.
Let's introduce a version scheme for s390-ccw-virtio machines.
We will use the old s390-ccw-virtio name as alias to the latest
version as all existing libvirt XML for the ccw type were expanded
by libvirt to that name.
The only downside of this patch is, that the old alias s390-ccw
will no longer be available as machines can have only one alias,
but it should not really matter.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1435742217-62246-1-git-send-email-borntraeger@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
commit fa92e218df ("s390x/ipl: avoid sign extension") introduced
a regression:
qemu-system-s390x -drive file=image.qcow,format=qcow2
does not boot, the bios states
"No virtio-blk device found!"
adding bootindex=1 does boot.
The reason is that the uint32_t as return value will not do the right
thing for the return -1 (default without bootindex).
The bios itself, will interpret a 64bit -1 as autodetect (but it will
interpret 32bit -1 as ccw device address ff.ff.ffff)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: qemu-stable@nongnu.org # v2.3.0
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
