Test that the FIS delivered after a nondata command has appropriately
updated registers, just as we'd expect a data command to do.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1434470575-21625-3-git-send-email-jsnow@redhat.com
The only guidance the AHCI specification gives on memory access is:
"Register accesses shall have a maximum size of 64-bits; 64-bit access
must not cross an 8-byte alignment boundary."
I interpret this to mean that aligned or unaligned 1, 2 and 4 byte
accesses should work, as well as aligned 8 byte accesses.
In practice, a real Q35/ICH9 responds to 1, 2, 4 and 8 byte reads
regardless of alignment. Windows 7 can be observed making 1 byte
reads to the middle of 32 bit registers to fetch error codes.
Introduce a wrapper to support unaligned accesses to AHCI.
This wrapper will support aligned 8 byte reads, but will make
no effort to support unaligned 8 byte reads, which although they
will work on real hardware, are not guaranteed to work and do
not appear to be used by either Windows or Linux.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1434470575-21625-2-git-send-email-jsnow@redhat.com
Introduce an API numa_get_node(ram_addr_t addr, Error **errp) that
returns the NUMA node to which the given address belongs to. This
API works uniformly for both boot time as well as hotplugged memory.
This API is needed by sPAPR PowerPC to support
ibm,dynamic-reconfiguration-memory device tree node which is needed for
memory hotplug.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Store memory address range information of boot memory in address
range list of numa_info.
This helps to have a common NUMA node lookup by address function that
works for both boot-time memory and hotplugged memory.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Start storing the (start_addr, end_addr) of the pc-dimm memory
in corresponding numa_info[node] so that this information can be used
to lookup node by address.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
HotplugHandlerClass::plug() shouldn't fail and hence use error_abort
to abort if it fails.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
pc_dimm_plug() has code that will be needed for memory plug handlers
in other archs too. Extract code from pc_dimm_plug() into a generic
routine pc_dimm_memory_plug() that resides in pc-dimm.c. Also
correspondingly refactor re-usable unplug code into pc_dimm_memory_unplug().
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move hotplug_memory_base and hotplug_memory fields of PCMachineState
into a separate structure so that the same can be made use of from
other architectures supporing memory hotplug.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add display and head properties for input routing to
virtio-input devices, update multiseat documentation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The section footer changes commit f68945d42b ("Add a protective
section footer") and commit 37fb569c01 ("Disable section footers
on older machine types") broke migration for any non-versioned
machines.
This pinpoints a problem of s390-ccw machines: it needs to
be versioned to be compatible with future changes in common
code data structures such as section footers.
Let's introduce a version scheme for s390-ccw-virtio machines.
We will use the old s390-ccw-virtio name as alias to the latest
version as all existing libvirt XML for the ccw type were expanded
by libvirt to that name.
The only downside of this patch is, that the old alias s390-ccw
will no longer be available as machines can have only one alias,
but it should not really matter.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1435742217-62246-1-git-send-email-borntraeger@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Whenever we touch the access control registers, we have to make sure that
the values will make it into kvm. Otherwise the change will simply be lost.
When synchronizing qemu and kvm, a normal KVM_PUT_RUNTIME_STATE does not take
care of these registers. Let's simply trigger a KVM_PUT_FULL_STATE sync,
so the values will directly be written to kvm. The performance overhead can
be ignored and this is much cleaner than manually writing these registers to kvm
via our two supported ways.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
commit fa92e218df ("s390x/ipl: avoid sign extension") introduced
a regression:
qemu-system-s390x -drive file=image.qcow,format=qcow2
does not boot, the bios states
"No virtio-blk device found!"
adding bootindex=1 does boot.
The reason is that the uint32_t as return value will not do the right
thing for the return -1 (default without bootindex).
The bios itself, will interpret a 64bit -1 as autodetect (but it will
interpret 32bit -1 as ccw device address ff.ff.ffff)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: qemu-stable@nongnu.org # v2.3.0
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We need to migrate the revision field as well. No compatibility
concerns as we already introduced migration of ->config_vector in
this release.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Support the new CCW_CMD_SET_VQ format for virtio-1 devices.
While we're at it, refactor the code a bit and enforce big endian
fields (which had always been required, even for legacy).
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Handle the virtio-ccw revision according to what the guest sets.
When revision 1 is selected, we have a virtio-1 standard device
with byteswapping for the virtio rings.
When a channel gets disabled, we have to revert to the legacy behavior
in case the next user of the device does not negotiate the revision 1
anymore (e.g. the boot firmware uses revision 1, but the operating
system only uses the legacy mode).
Note that revisions > 0 are still disabled.
[CH: assure memory accesses are always BE]
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJVlQAPAAoJEJykq7OBq3PIV7EH/iijbZ6q/i1UdinVsF09Dls3
f++CLEb2VUx25KqReDwUDjVsimBeb9jntLUyqHuHAYlCwrrJGcbTPQqw3d2k+MBB
pbWcaFyjGyHb7LOd1JOVRHK0z4QfjVNPu9IjGMsUXP3/JXtqkbIcLwg1UF6p/bzj
NXSaCv5NOSEpJdxCN/wYXCi78G9WfsSF0X1qCOLsJ/+sm8hung21T/o9CTph0Yua
6aiZodnB6vvk/YLPz1/RS37LabiMmgLeUdgbjxYhjBZBUQckmpOExm9gKRzujT/h
wZCuBeySdwqEDF0sLWOB9gDZRoTujStsnwpK6MmD/o0lXiWGbeYBtjakx93EY0c=
=HgNT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Thu Jul 2 10:10:39 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
block: remove redundant check before g_slist_find()
block/nfs: limit maximum readahead size to 1MB
block/iscsi: restore compatiblity with libiscsi 1.9.0
iotests: Use event_wait in wait_ready
qemu-iotests: Add test case for mirror with unmap
qemu-iotests: Make block job methods common
block: Remove bdrv_reset_dirty
block: Fix dirty bitmap in bdrv_co_discard
mirror: Do zero write on target if sectors not allocated
qmp: Add optional bool "unmap" to drive-mirror
block: Add bdrv_get_block_status_above
timer: Use a single definition of NSEC_PER_SEC for the whole codebase
timer: Move NANOSECONDS_PER_SECONDS to timer.h
blockdev: no need to drain+flush in hmp_drive_del
qapi: Rename 'dirty-bitmap' mode to 'incremental'
qcow2: Handle EAGAIN returned from update_refcount
block/iscsi: add support for request timeouts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An empty GSList is represented by a NULL pointer, therefore it's a
perfectly valid argument for g_slist_find() and there's no need to
make any additional check.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 1435583533-5758-1-git-send-email-berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
a malicious caller could otherwise specify a very
large value via the URI and force libnfs to allocate
a large amount of memory for the readahead buffer.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1435317241-25585-1-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
RHEL7 and others are stuck with libiscsi 1.9.0 since there
unfortunately was an ABI breakage after that release.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435313881-19366-1-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Only poll the specific type of event we are interested in, to avoid
stealing events that should be consumed by someone else.
Suggested-by: John Snow <jsnow@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This checks that the discard on mirror source that effectively zeroes
data is also reflected by the data of target.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Using this function would always be wrong because a dirty bitmap must
have a specific owner that consumes the dirty bits and calls
bdrv_reset_dirty_bitmap().
Remove the unused function to avoid future misuse.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Unsetting dirty globally with discard is not very correct. The discard may zero
out sectors (depending on can_write_zeroes_with_unmap), we should replicate
this change to destination side to make sure that the guest sees the same data.
Calling bdrv_reset_dirty also troubles mirror job because the hbitmap iterator
doesn't expect unsetting of bits after current position.
So let's do it the opposite way which fixes both problems: set the dirty bits
if we are to discard it.
Reported-by: wangxiaolong@ucloud.cn
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If guest discards a source cluster, mirroring with bdrv_aio_readv is overkill.
Some protocols do zero upon discard, where it's best to use
bdrv_aio_write_zeroes, otherwise, bdrv_aio_discard will be enough.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If specified as "true", it allows discarding on target sectors where source is
not allocated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Like bdrv_is_allocated_above, this function follows the backing chain until seeing
BDRV_BLOCK_ALLOCATED. Base is not included.
Reimplement bdrv_is_allocated on top.
[Initialized bdrv_co_get_block_status_above() ret to 0 to silence
mingw64 compiler warning about the unitialized variable. assert(bs !=
base) prevents that case but I suppose the program could be compiled
with -DNDEBUG.
--Stefan]
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We want to be able to reuse this define by making it common to
multiple QEMU modules.
This also makes it an integer since there's no need for it to be a
float.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 6375912849da2ab561046dd013684535ccecca44.1434113783.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_close already does that, and in fact hmp_drive_del would need
another drain after the flush (which bdrv_close does). So remove
the duplication.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1432822629-25401-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If we wish to make differential backups a feature that's easy to access,
it might be pertinent to rename the "dirty-bitmap" mode to "incremental"
to make it clear what /type/ of backup the dirty-bitmap is helping us
perform.
This is an API breaking change, but 2.4 has not yet gone live,
so we have this flexibility.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1433463642-21840-2-git-send-email-jsnow@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Fixes a crash during image compression
Signed-off-by: Jindřich Makovička <makovick@gmail.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
libiscsi starting with 1.15 will properly support timeout of iscsi
commands. The default will remain no timeout, but this can
be changed via cmdline parameters, e.g.:
qemu -iscsi timeout=30 -drive file=iscsi://...
If a timeout occurs a reconnect is scheduled and the timed out command
will be requeued for processing after a successful reconnect.
The required API call iscsi_set_timeout is present since libiscsi
1.10 which was released in October 2013. However, due to some bugs
in the libiscsi code the use is not recommended before version 1.15.
Please note that this patch bumps the libiscsi requirement to 1.10
to have all function and macros defined. The patch fixes also a
off-by-one error in the NOP timeout calculation which was fixed
while touching these code parts.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1434455107-19328-1-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Do not take the BQL before dispatching MMIO requests of KVM VCPUs.
Instead, address_space_rw will do it if necessary. This enables completely
BQL-free MMIO handling in KVM mode for upcoming devices with fine-grained
locking.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-10-git-send-email-pbonzini@redhat.com>
Accessing QEMU_CLOCK_VIRTUAL is thread-safe.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-9-git-send-email-pbonzini@redhat.com>
Do not take the BQL before dispatching PIO requests of KVM VCPUs.
Instead, address_space_rw will do it if necessary. This enables
completely BQL-free PIO handling in KVM mode for upcoming devices with
fine-grained locking.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-8-git-send-email-pbonzini@redhat.com>
This opens the path to get rid of the iothread lock on vmexits in KVM
mode. On x86, the in-kernel irqchips has to be used because we otherwise
need to synchronize APIC and other per-cpu state accesses that could be
changed concurrently.
Regarding pre/post-run callbacks, s390x and ARM should be fine without
specific locking as the callbacks are empty. MIPS and POWER require
locking for the pre-run callback.
For the handle_exit callback, it is non-empty in x86, POWER and s390.
Some POWER cases could do without the locking, but it is left in
place for now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-7-git-send-email-pbonzini@redhat.com>
The MMIO case is further broken up in two cases: if the caller does not
hold the BQL on invocation, the unlocked one takes or avoids BQL depending
on the locking strategy of the target memory region and its coalesced
MMIO handling. In this case, the caller should not hold _any_ lock
(a friendly suggestion which is disregarded by virtio-scsi-dataplane).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Frederic Konrad <fred.konrad@greensocs.com>
Message-Id: <1434646046-27150-6-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As memory_region_read/write_accessor will now be run also without BQL held,
we need to move coalesced MMIO flushing earlier in the dispatch process.
Cc: Frederic Konrad <fred.konrad@greensocs.com>
Message-Id: <1434646046-27150-5-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This introduces the memory region property "global_locking". It is true
by default. By setting it to false, a device model can request BQL-free
dispatching of region accesses to its r/w handlers. The actual BQL
break-up will be provided in a separate patch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Frederic Konrad <fred.konrad@greensocs.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-4-git-send-email-pbonzini@redhat.com>
This function will be used to avoid recursive locking of the iothread lock
whenever address_space_rw/ld*/st* are called with the BQL held, which is
almost always the case.
Tracking whether the iothread is owned is very cheap (just use a TLS
variable) but requires some care because now the lock must always be
taken with qemu_mutex_lock_iothread(). Previously this wasn't the case.
Outside TCG mode this is not a problem. In TCG mode, we need to be
careful and avoid the "prod out of compiled code" step if already
in a VCPU thread. This is easily done with a check on current_cpu,
i.e. qemu_in_vcpu_thread().
Hopefully, multithreaded TCG will get rid of the whole logic to kick
VCPUs whenever an I/O event occurs!
Cc: Frederic Konrad <fred.konrad@greensocs.com>
Message-Id: <1434646046-27150-3-git-send-email-pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The next patch will require the BQL to be always taken with
qemu_mutex_lock_iothread(), while right now this isn't the case.
Outside TCG mode this is not a problem. In TCG mode, we need to be
careful and avoid the "prod out of compiled code" step if already
in a VCPU thread. This is easily done with a check on current_cpu,
i.e. qemu_in_vcpu_thread().
Hopefully, multithreaded TCG will get rid of the whole logic to kick
VCPUs whenever an I/O event occurs!
Cc: Frederic Konrad <fred.konrad@greensocs.com>
Message-Id: <1434646046-27150-2-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Last month, we experienced several guests crash(6cores-8cores), qemu logs
display the following messages:
qemu-system-x86_64: /build/qemu-2.1.2/kvm-all.c:976:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.
After analysis and verification, we can confirm it's irq-balance
daemon(in guest) leads to the assertion failure. Start a 8 core guest with
two disks, execute the following scripts will reproduce the BUG quickly:
irq_affinity.sh
========================================================================
vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
for irq in {1,2,4,8,10,20,40,80}
do
echo $irq > /proc/irq/$vda_irq_num/smp_affinity
echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
done
done
========================================================================
QEMU setup static irq route entries in kvm_pc_setup_irq_routing(), PIC and
IOAPIC share the first 15 GSI numbers, take up 23 GSI numbers, but take up
38 irq route entries. When change irq smp_affinity in guest, a dynamic route
entry may be setup, the current logic is: if allocate GSI number succeeds,
a new route entry can be added. The available dynamic GSI numbers is
1021(KVM_MAX_IRQ_ROUTES-23), but available irq route entries is only
986(KVM_MAX_IRQ_ROUTES-38), GSI numbers greater than route entries.
irq-balance's behavior will eventually leads to total irq route entries
exceed KVM_MAX_IRQ_ROUTES, ioctl(KVM_SET_GSI_ROUTING) fail and
kvm_irqchip_commit_routes() trigger assertion failure.
This patch fix the BUG.
Signed-off-by: Wenshuang Ma <kevinnma@tencent.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need a possibility to run code when a subchannel gets disabled.
This patch adds the necessary infrastructure.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
We have to consume the outstanding service interrupt after each
service call, otherwise a correct implementation will return
CC=2 on subsequent service calls.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Our main channel_subsys structure is not a device (yet), but we need
to setup mss/mcss-e again if the guest had enabled it before. Use
a hack that should catch most configurations (assuming that the guest
will have enabled at least one device in higher subchannel sets or
channel subsystems if it enabled the functionality.)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>