AST2400_A0_SILICON_REV is defined twice. Fix this by including the
definition in the header file as well as the routine to check if a
silicon revision is supported. It will useful to reuse in other
controllers.
Let's add also AST2500_A0_SILICON_REV for future use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467994016-11678-5-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By specifying the silicon revision we select the appropriate reset
values for the SoC.
Additionally, expose hardware strapping properties aliasing those
provided by the SCU for board-specific configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466744305-23163-3-git-send-email-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to the APB bus. They can be programmed as master or
slave but the propopsed model only supports the master mode.
On the TODO list, we also have :
- improve and harden the state machine.
- bus recovery support (used by the Linux driver).
- transfer mode state machine bits. this is not strictly necessary as
it is mostly used for debug. The bus busy bit is deducted from the
I2C core engine of qemu.
- support of the pool buffer: 2048 bytes of internal SRAM (not used
by the Linux driver).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1464704307-25178-1-git-send-email-clg@kaod.org
[PMM: removed unused functions aspeed_i2c_bus_get_state() and
aspeed_i2c_bus_set_state()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While the ASPEED AST2400 SoC[1] has a broad range of capabilities this
implementation is minimal, comprising an ARM926 processor, ASPEED VIC
and timer devices, and a 8250 UART.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-4-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
