To allow reusing ISA bridge emulation for vt8231_isa move the device
state of vt82c686b_isa emulation in an abstract via_isa class. This
change breaks migration back compatibility but this is not an issue
for Fuloong2E machine which is not versioned or migration supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <0cb8fc69c7aaa555589181931b881335fecd2ef3.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The VT8231 south bridge is very similar to VT82C686B but there are
some differences in register addresses and functionality, e.g. the
VT8231 only has one serial port. This commit adds VT8231_SUPERIO
subclass based on the abstract VIA_SUPERIO class to emulate the
superio part of VT8231.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <8108809321f9ecf3fb1aea22ddaeccc7c3a57c8e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Collect superio functionality and its controlling config registers
handling in an abstract VIA_SUPERIO class that is a subclass of
ISA_SUPERIO and put vt82c686b specific parts in a subclass of this
abstract class.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <fbcc8cc8baf83f327612a1ef1c14bcbcdb0e7edb.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When adding the Reset register in commit 5790b757cf we
forgot to migrate it.
While it is possible a VM using the PIIX4 is migrated just
after requesting a system shutdown, it is very unlikely.
However when restoring a migrated VM, we might have the
RCR bit #4 set on the stack and when the VM resume it
directly shutdowns.
Add a post_load() migration handler and set the default
RCR value to 0 for earlier versions, assuming the VM was
not going to shutdown before migration.
Fixes: 5790b757cf ("piix4: Add the Reset Control Register")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210324200334.729899-1-f4bug@amsat.org>
TYPE_VIA_PM calls apm_init() in via_pm_realize(), so
requires APM to be selected.
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Fixes: dd0ff8191a ("isa: express SuperIO dependencies with Kconfig")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210302080531.913802-1-f4bug@amsat.org>
Commit 6be8cf56bc made sure that SCI is enabled in PM1.CNT
on reset in acpi_only mode by modifying acpi_pm1_cnt_reset() and
that worked for q35 as expected.
This patch adds reset ACPI PM related registers on vt82c686 reset time
and de-assert sci.
via_pm_realize() initializes acpi pm tmr, evt, cnt and gpe.
Reset them on device reset.
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <0a3fe998525552860919a690ce83dab8f663ab99.1616532563.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VT82C686 south bridge provides a USB UHCI bus via a PCI function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210309190802.830969-2-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If SMM is not supported, ACPI fixed hardware doesn't support
legacy-mode. ACPI-only platform. Where SCI_EN in PM1_CNT register is
always set.
The bit tells OS legacy mode(SCI_EN cleared) or ACPI mode(SCI_EN set).
With the next patch (setting fadt.smi_cmd = 0 when smm isn't enabled),
guest Linux tries to switch to ACPI mode, finds smi_cmd = 0, and then
fails to initialize acpi subsystem. This patch proactively fixes it.
This patch changes guest ABI. To keep compatibility, use
"smm-compat" introduced by earlier patch. If the property is true,
disable new behavior.
ACPI spec 4.8.10.1 PM1 Event Grouping
PM1 Eanble Registers
> For ACPI-only platforms (where SCI_EN is always set)
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <500f62081626997e46f96377393d3662211763a8.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following patch will introduce incompatible behavior of SMM.
Introduce a property to keep the old behavior for compatibility.
To enable smm compat, use "-global ICH9-LPC.smm-compat=on" or
"-global PIIX4_PM.smm-compat=on"
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <47254ae0b8c6cc6945422978b6b2af2d213ef891.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
These functions are memory region callbacks so we have to check
against relative address not the mapped address.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 5/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 4/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
By returning earlier we can remove the 'can_write' boolean variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 3/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split patch original in 5, this is part 2/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove the separate index value from SuperIOConfig and store
the index at reg 0 which is reserved and returns 0 on read.
This simplifies the object state.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 1/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently the ISA devices that are part of the VIA south bridge,
superio chip are wired up by board code. Move creation of these ISA
devices to the VIA ISA bridge model so that board code does not need
to access ISA bus. This also allows vt82c686b-superio to be made
internal to vt82c686 which allows implementing its configuration via
registers in subseqent commits.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <bf9400cc8e4ddd3129aa5678de4d3cf38384805f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove unneeded variables and setting value to 0 on zero initialised
data and replace check for error with error_fatal. Rationalise loop
that sets PCI config header fields read only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <e4caf35ca10a68f5c74ae3f93fa0bcfa9457beea.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This device is part of the multifunction VIA superio/south bridge chip
so not useful in itself.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <d0a806fed5e8055aee4fcf5b2f4790e6dd0f9dc6.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use less confusing naming for superio config register handling related
parts that makes it clearer what belongs to this part.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <4d30a2b4b771b2ad651509885daae79d7c4fe7a8.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rename local variable holding object state for readability and
consistency.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <69655b23df2ecebbf0aff29726f4b4746f5b74de.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are not used or not needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <35cefcc3518a3395a796bb6ad6fbc308adc65266.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Drop DPRINTF and use trace functions instead. Two debug messages about
unimplemented registers could be converted to qemu_log_mask() but in
reality all registers are currently unimplemented (we just store and
return values of writable regs but do nothing with them). As we
already trace register access there's no need for additional debug
messages so these are just removed and a comment is added as a reminder.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <785854022a37035f66d89e70cb6ca1bc0e0d0163.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove legacy vt82c686b_pm_init() function and also rename
VT82C686B_PM type name to match other device names.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a70982b32f11222d335385b90749abb6cf2e2cce.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The via-[am]c97 code is supposed to implement the audio part of VIA
south bridge chips so it is better placed under hw/audio/. Split it
off into a separate file.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <af083634e3b9efe67e6c4247cf0185d3fa7b1810.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These are legacy init functions that are just equivalent to directly
calling pci_create_simple so do that instead. Also rename objects to
lower case via-ac97 and via-mc97 matching naming of other devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1c4373c8aeb6c4fb2a8df2c864b0e91a977a3d7b.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is really the ISA bridge part so name the type accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <78db2ced4b41a8a775dbc6c97a90db683952c2cb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There's no reason to suffix everything with _DEVICE when the names are
already unique without it and shorter names are more readable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <ea89683ebb3528c0f79ed99d3d3cfcefb63c3bfb.1609584216.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These parts are common between VT82C686B and VT8231 so can be shared
in the future. Rename them to VIA prefix accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <510ddb17836a2c2e68a27cf2dcaee420bc2efbc1.1609584215.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We already have a generic PCI_SLOT() macro in "hw/pci/pci.h"
to extract the PCI slot identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-5-philmd@redhat.com>
Keep CPU hotunplug with SMI disabled on 5.2 and older and enable
it by default on newer machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be reused by next patch to check validity of unplug
feature.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023121933.19227-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0x8400f841
outl 0xcfc 0xebed205d
outl 0x5d02 0xedf82049
EOF
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
hw/pci/pci.c:268: int pci_bus_get_irq_level(PCIBus *, int): Assertion `irq_num < bus->nirq' failed.
This is because ich9_lpc_sci_irq() returns -1 for reserved
(illegal) values, but ich9_lpc_pmbase_sci_update() considers
it valid and store it in a 8-bit unsigned type. Then the 255
value is used as GSI IRQ, resulting in a PIRQ value of 247,
more than ICH9_LPC_NB_PIRQS (8).
Fix by simply ignoring the invalid access (and reporting it):
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
ICH9 LPC: SCI IRQ SEL #3 is reserved
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: 8f242cb724 ("ich9: implement SCI_IRQ_SEL register")
BugLink: https://bugs.launchpad.net/qemu/+bug/1878642
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200717151705.18611-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the "smi_negotiated_features" field of ICH9LPCState as
a QOM property.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow firmware to notify QEMU that firmware requires SMI
being triggered on CPU hot[un]plug, so that it would be able to account
for hotplugged CPU and relocate it to new SMM base and/or safely remove
CPU on unplug.
Using negotiated features, follow up patches will insert SMI upcall
into AML code, to make sure that firmware processes hotplug before
guest OS would attempt to use new CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This makes the code consistent with the rest of QOM code in QEMU,
and will make automated conversion to type declaration macros
simpler.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200824215936.2961951-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
