bdrv_backing_overridden is only used in block.c, so there is
no need to leave it in block_int.h
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211215121140.456939-2-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently QEMU defaults to a resolution of 1024x768 when exposing EDID
info to the guest OS. The EDID default info is important as this will
influence what resolution many guest OS will configure the screen with
on boot. It can also potentially influence what resolution the firmware
will configure the screen with, though until very recently EDK2 would
not handle EDID info.
One important thing to bear in mind is that the default graphics card
driver provided by Windows will leave the display set to whatever
resolution was enabled by the firmware on boot. Even if sufficient
VRAM is available, the resolution can't be changed without installing
new drivers. IOW, the default resolution choice is quite important
for usability of Windows.
Modern real world monitor hardware for desktop/laptop has supported
resolutions higher than 1024x768 for a long time now, perhaps as long
as 15+ years. There are quite a wide variety of native resolutions in
use today, however, and in wide screen form factors the height may not
be all that tall.
None the less, it is considered that there is scope for making the
QEMU default resolution slightly larger.
In considering what possible new default could be suitable, choices
considered were 1280x720 (720p), 1280x800 (WXGA) and 1280x1024 (SXGA).
In many ways, vertical space is the most important, and so 720p was
discarded due to loosing vertical space, despite being 25% wider.
The SXGA resolution would be good, but when taking into account
window titlebars/toolbars and window manager desktop UI, this might
be a little too tall for some users to fit the guest on their physical
montior.
This patch thus suggests a modest change to 1280x800 (WXGA). This
only consumes 1 MB per colour channel, allowing double buffered
framebuffer in 8 MB of VRAM. Width wise this is 25% larger than
QEMU's current default, but height wise this only adds 5%, so the
difference isn't massive on the QEMU side.
Overall there doesn't appear to be a compelling reason to stick
with 1024x768 resolution.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211129140508.1745130-1-berrange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
vga_mmio_init() is used only one time and not very helpful,
inline and remove it.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211206224528.563588-5-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Introduce TYPE_VGA_MMIO, a sysbus device.
While there is no change in the vga_mmio_init()
interface, this is a migration compatibility break
of the MIPS Acer Pica 61 Jazz machine (pica61).
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211206224528.563588-4-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no ISA bus part in the MMIO VGA device, so rename:
* hw/display/vga-isa-mm.c -> hw/display/vga-mmio.c
* CONFIG_VGA_ISA_MM -> CONFIG_VGA_MMIO
* ISAVGAMMState -> VGAMmioState
* isa_vga_mm_init() -> vga_mmio_init()
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206224528.563588-2-f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Now that virtio-blk and virtio-scsi are ready, get rid of
the handle_aio_output() callback. It's no longer needed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-7-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The return value of virtio_blk_handle_vq() is no longer used. Get rid of
it. This is a step towards unifying the dataplane and non-dataplane
virtqueue handler functions.
Prepare virtio_blk_handle_output() to be used by both dataplane and
non-dataplane by making the condition for starting ioeventfd more
specific. This way it won't trigger when dataplane has already been
started.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The virtqueue host notifier API
virtio_queue_aio_set_host_notifier_handler() polls the virtqueue for new
buffers. AioContext previously required a bool progress return value
indicating whether an event was handled or not. This is no longer
necessary because the AioContext polling API has been split into a poll
check function and an event handler function. The event handler is only
run when we know there is work to do, so it doesn't return bool.
The VirtIOHandleAIOOutput function signature is now the same as
VirtIOHandleOutput. Get rid of the bool return value.
Further simplifications will be made for virtio-blk and virtio-scsi in
the next patch.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Adaptive polling measures the execution time of the polling check plus
handlers called when a polled event becomes ready. Handlers can take a
significant amount of time, making it look like polling was running for
a long time when in fact the event handler was running for a long time.
For example, on Linux the io_submit(2) syscall invoked when a virtio-blk
device's virtqueue becomes ready can take 10s of microseconds. This
can exceed the default polling interval (32 microseconds) and cause
adaptive polling to stop polling.
By excluding the handler's execution time from the polling check we make
the adaptive polling calculation more accurate. As a result, the event
loop now stays in polling mode where previously it would have fallen
back to file descriptor monitoring.
The following data was collected with virtio-blk num-queues=2
event_idx=off using an IOThread. Before:
168k IOPS, IOThread syscalls:
9837.115 ( 0.020 ms): IO iothread1/620155 io_submit(ctx_id: 140512552468480, nr: 16, iocbpp: 0x7fcb9f937db0) = 16
9837.158 ( 0.002 ms): IO iothread1/620155 write(fd: 103, buf: 0x556a2ef71b88, count: 8) = 8
9837.161 ( 0.001 ms): IO iothread1/620155 write(fd: 104, buf: 0x556a2ef71b88, count: 8) = 8
9837.163 ( 0.001 ms): IO iothread1/620155 ppoll(ufds: 0x7fcb90002800, nfds: 4, tsp: 0x7fcb9f1342d0, sigsetsize: 8) = 3
9837.164 ( 0.001 ms): IO iothread1/620155 read(fd: 107, buf: 0x7fcb9f939cc0, count: 512) = 8
9837.174 ( 0.001 ms): IO iothread1/620155 read(fd: 105, buf: 0x7fcb9f939cc0, count: 512) = 8
9837.176 ( 0.001 ms): IO iothread1/620155 read(fd: 106, buf: 0x7fcb9f939cc0, count: 512) = 8
9837.209 ( 0.035 ms): IO iothread1/620155 io_submit(ctx_id: 140512552468480, nr: 32, iocbpp: 0x7fca7d0cebe0) = 32
174k IOPS (+3.6%), IOThread syscalls:
9809.566 ( 0.036 ms): IO iothread1/623061 io_submit(ctx_id: 140539805028352, nr: 32, iocbpp: 0x7fd0cdd62be0) = 32
9809.625 ( 0.001 ms): IO iothread1/623061 write(fd: 103, buf: 0x5647cfba5f58, count: 8) = 8
9809.627 ( 0.002 ms): IO iothread1/623061 write(fd: 104, buf: 0x5647cfba5f58, count: 8) = 8
9809.663 ( 0.036 ms): IO iothread1/623061 io_submit(ctx_id: 140539805028352, nr: 32, iocbpp: 0x7fd0d0388b50) = 32
Notice that ppoll(2) and eventfd read(2) syscalls are eliminated because
the IOThread stays in polling mode instead of falling back to file
descriptor monitoring.
As usual, polling is not implemented on Windows so this patch ignores
the new io_poll_read() callback in aio-win32.c.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20211207132336.36627-2-stefanha@redhat.com
[Fixed up aio_set_event_notifier() calls in
tests/unit/test-fdmon-epoll.c added after this series was queued.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Its only callers are inside pnv_phb4.c.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220111131027.599784-6-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
At this moment, stack->phb is the plain PnvPHB4 device itself instead of
a pointer to the device. This will present a problem when adding user
creatable devices because we can't deal with this struct and the
realize() callback from the user creatable device.
We can't get rid of this attribute, similar to what we did when enabling
pnv-phb3 user creatable devices, because pnv_phb4_update_regions() needs
to access stack->phb to do its job. This function is called twice in
pnv_pec_stk_update_map(), which is one of the nested xscom write
callbacks (via pnv_pec_stk_nest_xscom_write()). In fact,
pnv_pec_stk_update_map() code comment is explicit about how the order of
the unmap/map operations relates with the PHB subregions.
All of this indicates that this code is tied together in a way that we
either go on a crusade, featuring lots of refactories and redesign and
considerable pain, to decouple stack and phb mapping, or we allow stack
update_map operations to access the associated PHB as it is today even
after introducing pnv-phb4 user devices.
This patch chooses the latter. Instead of getting rid of stack->phb,
turn it into a PHB pointer. This will allow us to assign an user created
PHB to an existing stack later. In this process,
pnv_pec_stk_instance_init() is removed because stack->phb is being
initialized in stk_realize() instead.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220111131027.599784-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The logic inside pnv_pec_phb_offset() will be useful in the next patch
to determine the stack that should contain a PHB4 device.
Move the function to pnv_phb4.c and make it public since there's no
pnv_phb4_pec.h header. While we're at it, add 'stack_index' as a
parameter and make the function return 'phb-id' directly. And rename it
to pnv_phb4_pec_get_phb_id() to be even clearer about the function
intent.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220110143346.455901-3-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Similar to what was happening with pnv-phb3 buses,
TYPE_PNV_PHB4_ROOT_BUS set to "pnv-phb4-root-bus" is a bit too long for
a default root bus name. The usual default name for theses buses in QEMU
are 'pcie', but we want to make a distinction between pnv-phb4 buses and
other PCIE buses, at least as far as default name goes, because not all
PCIE devices are attachable to a pnv-phb4 root-bus type.
Changing the default to 'pnv-phb4-root' allow us to have a shorter name
while making this bus distinct, and the user can always set its own bus
naming via the "id" attribute anyway.
This is the 'info qtree' output after this change, using a powernv9
domain with 2 sockets and default settings enabled:
qemu-system-ppc64 -m 4G -machine powernv9,accel=tcg \
-smp 2,sockets=2,cores=1,threads=1
dev: pnv-phb4, id ""
index = 5 (0x5)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.11
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(...)
dev: pnv-phb4, id ""
index = 0 (0x0)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.6
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(..)
dev: pnv-phb4, id ""
index = 5 (0x5)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.5
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(...)
dev: pnv-phb4, id ""
index = 0 (0x0)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.0
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220110143346.455901-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The TYPE_PNV_PHB3_ROOT_BUS name is used as the default bus name when
the dev has no 'id'. However, pnv-phb3-root-bus is a bit too long to be
used as a bus name.
Most common QEMU buses and PCI controllers are named based on their bus
type (e.g. pSeries spapr-pci-host-bridge is called 'pci'). The most
common name for a PCIE bus controller in QEMU is 'pcie'. Naming it
'pcie' would break the documented use of the pnv-phb3 device, since
'pcie.0' would now refer to the root bus instead of the first root port.
There's nothing particularly wrong with the 'root-bus' name used before,
aside from the fact that 'root-bus' is being used for pnv-phb3 and
pnv-phb4 created buses, which is not quite correct since these buses
aren't implemented the same way in QEMU - you can't plug a
pnv-phb4-root-port into a pnv-phb3 root bus, for example.
This patch renames it as 'pnv-phb3-root', which is a compromise between
the existing and the previously used name. Creating 3 phbs without ID
will result in an "info qtree" output similar to this:
bus: main-system-bus
type System
dev: pnv-phb3, id ""
index = 2 (0x2)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.2
type pnv-phb3-root
(...)
dev: pnv-phb3, id ""
index = 1 (0x1)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.1
type pnv-phb3-root
(...)
dev: pnv-phb3, id ""
index = 0 (0x0)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.0
type pnv-phb3-root
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used elsewhere so that's where it belongs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-10-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The powernv machine uses the object hierarchy to populate the device
tree and each device should be parented to the chip it belongs to.
This is not the case for user created devices which are parented to
the container "/unattached".
Make sure a PHB3 device is parented to its chip by reparenting the
object if necessary.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
PHB3 devices and PCI devices can now be added to the powernv8 machine
using :
-device pnv-phb3,chip-id=0,index=1 \
-device nec-usb-xhci,bus=pci.1,addr=0x0
The 'index' property identifies the PHB3 in the chip. In case of user
created devices, a lookup on 'chip-id' is required to assign the
owning chip.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220105212338.49899-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We want to create only the absolutely minimal amount of devices when
running with -nodefaults. The root port is something that the machine
can boot up without. But, to do that, we need to provide a way for the
user to add them by hand.
This patch makes pnv-phb4-root-port user creatable and then uses the
pnv_phb_attach_root_port() helper to add a pnv_phb4_root_port only when
running with default settings.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-5-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleanups the PHB3 model a bit more since the root port is an
independent device and it will ease our task when adding user created
PHB3s.
pnv_phb_attach_root_port() is made public in pnv.c so it can be reused
with the pnv_phb4 root port later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This reverts commit 8806237234.
Fixes: 8806237234 ("vhost: introduce new VhostOps vhost_set_config_call")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 081f864f56.
Fixes: 081f864f56 ("virtio: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit f7220a7ce2.
Fixes: f7220a7ce2 ("vhost: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 497679d510.
Fixes: 497679d510 ("virtio-net: add support for configure interrupt")
Cc: "Cindy Lu" <lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds the support of the '-cpu rv128' option to
qemu-system-riscv64 so that we can indicate that we want to run rv128
executables.
Still, there is no support for 128-bit insns at that stage so qemu fails
miserably (as expected) if launched with this option.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Co-authored-by: Fabien Portas <fabien.portas@grenoble-inp.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-8-frederic.petrot@univ-grenoble-alpes.fr
[ Changed by AF
- Rename CPU to "x-rv128"
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Addition of div and rem on 128-bit integers, using the 128/64->128 divu and
64x64->128 mulu in host-utils.
These operations will be used within div/rem helpers in the 128-bit riscv
target.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Co-authored-by: Fabien Portas <fabien.portas@grenoble-inp.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-4-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adding defines to handle signed 64-bit and unsigned 128-bit quantities in
memory accesses.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-3-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Renaming defines for quad in their various forms so that their signedness is
now explicit.
Done using git grep as suggested by Philippe, with a bit of hand edition to
keep assignments aligned.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-2-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux supports up to 32 cores for both 32-bit and 64-bit RISC-V, so
let's set that as the maximum for the virt board.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/435
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-9-alistair.francis@opensource.wdc.com>
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHY2zEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpCiEH/jv5tHUffDdGz5M2pN7FTWPQ9UAMQZXbn5AS
PPVutOI/B+ILYBuNjYLvMGeq6ymG4/0DM940/jkQwCWD4ku1OG0ReM5T5klUR8lY
df5y1SCDv3Yoq0vxpQCnssKqbgm8Kf9tnAFjni7Lvbu3oo6DCq77m6MWEapLoEUu
IkM+l60NKmHAClnE6RF4KobLa5srIlDTho1iBXH5S39CRF1LvP9NgnYzl7nqiEkq
ZYQEqkKO5XGxZji9banZPJD2kxt1iL7s24QI6OJG2Lz8Hf86b0Yo7XJpmw4ShP9h
Vl1SL3m/HhHSMBuXOb7w/EkCm59b7whXCmoyYBF/GqaxtZkvVnM=
=4VIN
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci,pc: features,fixes,cleanups
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 07 Jan 2022 04:30:41 PM PST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (55 commits)
tests: acpi: Add updated TPM related tables
acpi: tpm: Add missing device identification objects
tests: acpi: prepare for updated TPM related tables
virtio/vhost-vsock: don't double close vhostfd, remove redundant cleanup
hw/scsi/vhost-scsi: don't double close vhostfd on error
hw/scsi/vhost-scsi: don't leak vqs on error
docs: reSTify virtio-balloon-stats documentation and move to docs/interop
hw/i386/pc: Add missing property descriptions
acpihp: simplify acpi_pcihp_disable_root_bus
tests: acpi: SLIC: update expected blobs
tests: acpi: add SLIC table test
tests: acpi: whitelist expected blobs before changing them
acpi: fix QEMU crash when started with SLIC table
intel-iommu: correctly check passthrough during translation
virtio-mem: Set "unplugged-inaccessible=auto" for the 7.0 machine on x86
virtio-mem: Support VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
linux-headers: sync VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
MAINTAINERS: Add a separate entry for acpi/VIOT tables
virtio: signal after wrapping packed used_idx
virtio-mem: Support "prealloc=on" option
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE, we signal the VM that reading
unplugged memory is not supported. We have to fail feature negotiation
in case the guest does not support VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE.
First, VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE is required to properly handle
memory backends (or architectures) without support for the shared zeropage
in the hypervisor cleanly. Without the shared zeropage, even reading an
unpopulated virtual memory location can populate real memory and
consequently consume memory in the hypervisor. We have a guaranteed shared
zeropage only on MAP_PRIVATE anonymous memory.
Second, we want VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE to be the default
long-term as even populating the shared zeropage can be problematic: for
example, without THP support (possible) or without support for the shared
huge zeropage with THP (unlikely), the PTE page tables to hold the shared
zeropage entries can consume quite some memory that cannot be reclaimed
easily.
Third, there are other optimizations+features (e.g., protection of
unplugged memory, reducing the total memory slot size and bitmap sizes)
that will require VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE.
We really only support x86 targets with virtio-mem for now (and
Linux similarly only support x86), but that might change soon, so prepare
for different targets already.
Add a new "unplugged-inaccessible" tristate property for x86 targets:
- "off" will keep VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE unset and legacy
guests working.
- "on" will set VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE and stop legacy guests
from using the device.
- "auto" selects the default based on support for the shared zeropage.
Warn in case the property is set to "off" and we don't have support for the
shared zeropage.
For existing compat machines, the property will default to "off", to
not change the behavior but eventually warn about a problematic setup.
Short-term, we'll set the property default to "auto" for new QEMU machines.
Mid-term, we'll set the property default to "on" for new QEMU machines.
Long-term, we'll deprecate the parameter and disallow legacy
guests completely.
The property has to match on the migration source and destination. "auto"
will result in the same VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE setting as long
as the qemu command line (esp. memdev) match -- so "auto" is good enough
for migration purposes and the parameter doesn't have to be migrated
explicitly.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134039.29670-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's synchronize the new feature flag, available in Linux since
v5.16-rc1.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134039.29670-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For scarce memory resources, such as hugetlb, we want to be able to
prealloc such memory resources in order to not crash later on access. On
simple user errors we could otherwise easily run out of memory resources
an crash the VM -- pretty much undesired.
For ordinary memory devices, such as DIMMs, we preallocate memory via the
memory backend for such use cases; however, with virtio-mem we're dealing
with sparse memory backends; preallocating the whole memory backend
destroys the whole purpose of virtio-mem.
Instead, we want to preallocate memory when actually exposing memory to the
VM dynamically, and fail plugging memory gracefully + warn the user in case
preallocation fails.
A common use case for hugetlb will be using "reserve=off,prealloc=off" for
the memory backend and "prealloc=on" for the virtio-mem device. This
way, no huge pages will be reserved for the process, but we can recover
if there are no actual huge pages when plugging memory. Libvirt is
already prepared for this.
Note that preallocation cannot protect from the OOM killer -- which
holds true for any kind of preallocation in QEMU. It's primarily useful
only for scarce memory resources such as hugetlb, or shared file-backed
memory. It's of little use for ordinary anonymous memory that can be
swapped, KSM merged, ... but we won't forbid it.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134611.31172-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The ITS code has to check whether various parameters passed in
commands are in-bounds, where the limit is defined in terms of the
number of bits that are available for the parameter. (For example,
the GITS_TYPER.Devbits ID register field specifies the number of
DeviceID bits minus 1, and device IDs passed in the MAPTI and MAPD
command packets must fit in that many bits.)
Currently we have off-by-one bugs in many of these bounds checks.
The typical problem is that we define a max_foo as 1 << n. In
the Devbits example, we set
s->dt.max_ids = 1UL << (GITS_TYPER.Devbits + 1).
However later when we do the bounds check we write
if (devid > s->dt.max_ids) { /* command error */ }
which incorrectly permits a devid of 1 << n.
These bugs will not cause QEMU crashes because the ID values being
checked are only used for accesses into tables held in guest memory
which we access with address_space_*() functions, but they are
incorrect behaviour of our emulation.
Fix them by standardizing on this pattern:
* bounds limits are named num_foos and are the 2^n value
(equal to the number of valid foo values)
* bounds checks are either
if (fooid < num_foos) { good }
or
if (fooid >= num_foos) { bad }
In this commit we fix the handling of the number of IDs
in the device table and the collection table, and the number
of commands that will fit in the command queue.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The TableDesc struct defines properties of the in-guest-memory tables
which the guest tells us about by writing to the GITS_BASER<n>
registers. This struct currently has a union 'maxids', but all the
fields of the union have the same type (uint32_t) and do the same
thing (record one-greater-than the maximum ID value that can be used
as an index into the table).
We're about to add another table type (the GICv4 vPE table); rather
than adding another specifically-named union field for that table
type with the same type as the other union fields, remove the union
entirely and just have a 'uint32_t max_ids' struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
AST2600 Display Port MCU introduces 0x18000000~0x1803FFFF as it's memory
and io address. If guest machine try to access DPMCU memory, it will
cause a fatal error.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20211210083034.726610-1-troy_lee@aspeedtech.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's sense support and use it for preallocation. MADV_POPULATE_WRITE
does not require a SIGBUS handler, doesn't actually touch page content,
and avoids context switches; it is, therefore, faster and easier to handle
than our current approach.
While MADV_POPULATE_WRITE is, in general, faster than manual
prefaulting, and especially faster with 4k pages, there is still value in
prefaulting using multiple threads to speed up preallocation.
More details on MADV_POPULATE_WRITE can be found in the Linux commits
4ca9b3859dac ("mm/madvise: introduce MADV_POPULATE_(READ|WRITE) to prefault
page tables") and eb2faa513c24 ("mm/madvise: report SIGBUS as -EFAULT for
MADV_POPULATE_(READ|WRITE)"), and in the man page proposal [1].
This resolves the TODO in do_touch_pages().
In the future, we might want to look into using fallocate(), eventually
combined with MADV_POPULATE_READ, when dealing with shared file/fd
mappings and not caring about memory bindings.
[1] https://lkml.kernel.org/r/20210816081922.5155-1-david@redhat.com
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211217134611.31172-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The i440fx and Q35 machine types are both hardcoded to use the
legacy SMBIOS 2.1 (32-bit) entry point. This is a sensible
conservative choice because SeaBIOS only supports SMBIOS 2.1
EDK2, however, can also support SMBIOS 3.0 (64-bit) entry points,
and QEMU already uses this on the ARM virt machine type.
This adds a property to allow the choice of SMBIOS entry point
versions For example to opt in to 64-bit SMBIOS entry point:
$QEMU -machine q35,smbios-entry-point-type=64
Based on a patch submitted by Daniel Berrangé.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-4-ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This prepares for exposing the SMBIOS entry point type as a
machine property on x86.
Based on a patch from Daniel P. Berrangé.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-3-ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Rename the enums to match the naming style used by QAPI, and to
use "32" and "64" instead of "20" and "31". This will allow us
to more easily move the enum to the QAPI schema later.
About the naming choice: "SMBIOS 2.1 entry point"/"SMBIOS 3.0
entry point" and "32-bit entry point"/"64-bit entry point" are
synonymous in the SMBIOS specification. However, the phrases
"32-bit entry point" and "64-bit entry point" are used more often.
The new names also avoid confusion between the entry point format
and the actual SMBIOS version reported in the entry point
structure. For example: currently the 32-bit entry point
actually report SMBIOS 2.8 support, not 2.1.
Based on portions of a patch submitted by Daniel P. Berrangé.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-2-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move the pci_intx() definition to the PCI header file, so that it can
be called from other PCI files. It is used by the next patch.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20211116170133.724751-3-fbarrat@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Add functions to support configure interrupt in virtio_net
The functions are config_pending and config_mask, while
this input idx is VIRTIO_CONFIG_IRQ_IDX will check the
function of configure interrupt.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-9-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt.
The configure interrupt process will start in vhost_dev_start
and stop in vhost_dev_stop.
Also add the functions to support vhost_config_pending and
vhost_config_mask, for masked_config_notifier, we only
use the notifier saved in vq 0.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-8-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the functions to support the configure interrupt in virtio
The function virtio_config_guest_notifier_read will notify the
guest if there is an configure interrupt.
The function virtio_config_set_guest_notifier_fd_handler is
to set the fd hander for the notifier
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-7-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces new VhostOps vhost_set_config_call. This function allows the
vhost to set the event fd to kernel
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-5-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This requires extra work for each target, but adds the
common syscall code, and the necessary flag in CPUState.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211227150127.2659293-4-richard.henderson@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add 7.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211217143948.289995-1-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Remove qemu_run_machine_init_done_notifiers() since no implementation
and user.
Fixes: f66dc8737c ("vl: move all generic initialization out of vl.c")
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220104024136.1433545-1-xiaoyao.li@intel.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The new Cluster-Aware Scheduling support has landed in Linux 5.16,
which has been proved to benefit the scheduling performance (e.g.
load balance and wake_affine strategy) on both x86_64 and AArch64.
So now in Linux 5.16 we have four-level arch-neutral CPU topology
definition like below and a new scheduler level for clusters.
struct cpu_topology {
int thread_id;
int core_id;
int cluster_id;
int package_id;
int llc_id;
cpumask_t thread_sibling;
cpumask_t core_sibling;
cpumask_t cluster_sibling;
cpumask_t llc_sibling;
}
A cluster generally means a group of CPU cores which share L2 cache
or other mid-level resources, and it is the shared resources that
is used to improve scheduler's behavior. From the point of view of
the size range, it's between CPU die and CPU core. For example, on
some ARM64 Kunpeng servers, we have 6 clusters in each NUMA node,
and 4 CPU cores in each cluster. The 4 CPU cores share a separate
L2 cache and a L3 cache tag, which brings cache affinity advantage.
In virtualization, on the Hosts which have pClusters (physical
clusters), if we can design a vCPU topology with cluster level for
guest kernel and have a dedicated vCPU pinning. A Cluster-Aware
Guest kernel can also make use of the cache affinity of CPU clusters
to gain similar scheduling performance.
This patch adds infrastructure for CPU cluster level topology
configuration and parsing, so that the user can specify cluster
parameter if their machines support it.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211228092221.21068-3-wangyanan55@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Added '(since 7.0)' to @clusters in qapi/machine.json]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
All methods related to MachineState are prefixed with "machine_".
smp_parse() does not need to be an exception. Rename it and
const'ify the SMPConfiguration argument, since it doesn't need
to be modified.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211216132015.815493-9-philmd@redhat.com>
@pin is an input where we connect a device output.
Rename it @input_pin to simplify the documentation.
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211218130437.1516929-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
qdev_connect_gpio_out_named() is described as qdev_connect_gpio_out(),
and referring to itself in an endless loop, which is confusing. Fix.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211218130437.1516929-4-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
qdev_init_gpio_out_named() is described as qdev_init_gpio_out(),
and referring to itself in an endless loop, which is confusing. Fix.
Reported-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211218130437.1516929-3-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Add empty lines to have a clearer distinction between different
functions declarations.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211218130437.1516929-2-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
ld*_dma() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-24-philmd@redhat.com>
st*_dma() returns a MemTxResult type. Do not discard
it, return it to the caller.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-23-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-22-philmd@redhat.com>
Let devices specify transaction attributes when calling st*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-21-philmd@redhat.com>
dma_memory_read() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-19-philmd@redhat.com>
dma_memory_write() returns a MemTxResult type. Do not discard
it, return it to the caller.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-18-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-17-philmd@redhat.com>
Let devices specify transaction attributes when calling st*_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-16-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_buf_read().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-13-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_buf_write().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-12-philmd@redhat.com>
Let devices specify transaction attributes when calling pci_dma_rw().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-10-philmd@redhat.com>
DMA operations are run on any kind of buffer, not arrays of
uint8_t. Convert dma_buf_read/dma_buf_write functions to take
a void pointer argument and save us pointless casts to uint8_t *.
Remove this pointless casts in the megasas device model.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-9-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_map().
Patch created mechanically using spatch with this script:
@@
expression E1, E2, E3, E4;
@@
- dma_memory_map(E1, E2, E3, E4)
+ dma_memory_map(E1, E2, E3, E4, MEMTXATTRS_UNSPECIFIED)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-7-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_rw().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-5-philmd@redhat.com>
We will add the MemTxAttrs argument to dma_memory_rw() in
the next commit. Since dma_memory_rw_relaxed() is only used
by dma_memory_rw(), modify it first in a separate commit to
keep the next commit easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-4-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_set().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-3-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_valid().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-2-philmd@redhat.com>
It's unused now (except for permission handling)[*]. The only reasonable
user of it was block-stream job, recently updated to use own blk. And
other block jobs prefer to use own source node related objects.
So, the arguments of dropping the field are:
- block jobs prefer not to use it
- block jobs usually has more then one node to operate on, and better
to operate symmetrically (for example has both source and target
blk's in specific block-job state structure)
*: BlockJob.blk is used to keep some permissions. We simply move
permissions to block-job child created in block_job_create() together
with blk.
In mirror, we just should not care anymore about restoring state of
blk. Most probably this code could be dropped long ago, after dropping
bs->job pointer. Now it finally goes away together with BlockJob.blk
itself.
iotest 141 output is updated, as "bdrv_has_blk(bs)" check in
qmp_blockdev_del() doesn't fail (we don't have blk now). Still, new
error message looks even better.
In iotest 283 we need to add a job id, otherwise "Invalid job ID"
happens now earlier than permission check (as permissions moved from
blk to block-job node).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Nikita Lapshin <nikita.lapshin@virtuozzo.com>
We are going to drop BlockJob.blk. So let's retrieve block job context
from underlying job instead of main node.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Nikita Lapshin <nikita.lapshin@virtuozzo.com>
Add a new chardev backend which allows D-Bus client to handle the
chardev stream & events.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add an option to use direct connections instead of via the bus. Clients
are accepted with QMP add_client.
This allows to provide the D-Bus display without a bus. It also
simplifies the testing setup (some CI have issues to setup a D-Bus bus
in a container).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
The "dbus" display backend exports the QEMU consoles and other
UI-related interfaces over D-Bus.
By default, the connection is established on the session bus, but you
can specify a different bus with the "addr" option.
The backend takes the "org.qemu" service name, while still allowing
further instances to queue on the same name (so you can lookup all the
available instances too). It accepts any number of clients at this
point, although this is expected to evolve with options to restrict
clients, or only accept p2p via fd passing.
The interface is intentionally very close to the internal QEMU API,
and can be introspected or interacted with busctl/dfeet etc:
$ ./qemu-system-x86_64 -name MyVM -display dbus
$ busctl --user introspect org.qemu /org/qemu/Display1/Console_0
org.qemu.Display1.Console interface - - -
.RegisterListener method h - -
.SetUIInfo method qqiiuu - -
.DeviceAddress property s "pci/0000/01.0" emits-change
.Head property u 0 emits-change
.Height property u 480 emits-change
.Label property s "VGA" emits-change
.Type property s "Graphic" emits-change
.Width property u 640 emits-change
[...]
See the interfaces XML source file and Sphinx docs for the generated API
documentations.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Add a new DisplayScanout structure to save the current scanout details.
This allows to attach later UI backends and set the scanout.
Introduce displaychangelistener_display_console() helper function to
handle the dpy_gfx_switch/gl_scanout() & dpy_gfx_update() calls.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
This will allow to have one GL context but a variable number of
listeners.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
GraphicHw.gl_flushed was introduced to notify the
device (vhost-user-gpu) that the GL resources (the display scanout) are
no longer needed.
It was decoupled from QEMU own gl-blocking mechanism, but that
difference isn't helping. Instead, we can reuse QEMU gl-blocking and
notify virtio_gpu_gl_flushed() when unblocking (to unlock
vhost-user-gpu).
An extra block/unblock is added arount dpy_gl_update() so existing
backends that don't block will have the flush event handled. It will
also help when there are no backends associated.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
The next patch will make use of this function to dissociate
DisplayChangeListener from GL context.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
A remote client, such as Spice, will already avoid flooding the stream
by delaying the resize requests.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Use a QemuClipboardNotify union type for extendable clipboard events.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Move linux-user safe-syscall.S and safe-syscall-error.c to common-user
so that bsd-user can also use it. Also move safe-syscall.h to
include/user/. Since there is nothing here that is related to the guest,
as opposed to the host, build it once.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit 739e95f574 ("scsi: Replace scsi_bus_new() with
scsi_bus_init(), scsi_bus_init_named()") forgot to rename
scsi_bus_init() in the function documentation string.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211122104744.1051554-1-f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"if (tcg_enabled())" allows elision of the code inside it; we only need
the prototype to exist, so that the code compile even for the --disable-tcg
case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* General cleanup for Mac machines (Peter)
* Fixes for FPU exceptions (Lucas)
* Support for new ISA31 instructions (Matheus)
* Fixes for ivshmem (Daniel)
* Cleanups for PowerNV PHB (Christophe and Cedric)
* Updates of PowerNV and pSeries documentation (Leonardo and Daniel)
* Fixes for PowerNV (Daniel)
* Large cleanup of FPU implementation (Richard)
* Removal of SoftTLBs support for PPC74x CPUs (Fabiano)
* Fixes for exception models in MPCx and 60x CPUs (Fabiano)
* Removal of 401/403 CPUs (Cedric)
* Deprecation of taihu machine (Thomas)
* Large rework of PPC405 machine (Cedric)
* Fixes for VSX instructions (Victor and Matheus)
* Fix for e6500 CPU (Fabiano)
* Initial support for PMU (Daniel)
-----BEGIN PGP SIGNATURE-----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=APFd
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20211217' of https://github.com/legoater/qemu into staging
ppc 7.0 queue:
* General cleanup for Mac machines (Peter)
* Fixes for FPU exceptions (Lucas)
* Support for new ISA31 instructions (Matheus)
* Fixes for ivshmem (Daniel)
* Cleanups for PowerNV PHB (Christophe and Cedric)
* Updates of PowerNV and pSeries documentation (Leonardo and Daniel)
* Fixes for PowerNV (Daniel)
* Large cleanup of FPU implementation (Richard)
* Removal of SoftTLBs support for PPC74x CPUs (Fabiano)
* Fixes for exception models in MPCx and 60x CPUs (Fabiano)
* Removal of 401/403 CPUs (Cedric)
* Deprecation of taihu machine (Thomas)
* Large rework of PPC405 machine (Cedric)
* Fixes for VSX instructions (Victor and Matheus)
* Fix for e6500 CPU (Fabiano)
* Initial support for PMU (Daniel)
# gpg: Signature made Fri 17 Dec 2021 09:20:31 AM PST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-ppc-20211217' of https://github.com/legoater/qemu: (101 commits)
ppc/pnv: Use QOM hierarchy to scan PEC PHB4 devices
ppc/pnv: Move realize of PEC stacks under the PEC model
ppc/pnv: Remove "system-memory" property from PHB4 PEC
ppc/pnv: Compute the PHB index from the PHB4 PEC model
ppc/pnv: Introduce a num_stack class attribute
ppc/pnv: Introduce a "chip" property under the PHB4 model
ppc/pnv: Introduce version and device_id class atributes for PHB4 devices
ppc/pnv: Introduce a num_pecs class attribute for PHB4 PEC devices
ppc/pnv: Use QOM hierarchy to scan PHB3 devices
ppc/pnv: Move mapping of the PHB3 CQ regions under pnv_pbcq_realize()
ppc/pnv: Drop the "num-phbs" property
ppc/pnv: Use the chip class to check the index of PHB3 devices
ppc/pnv: Introduce a "chip" property under PHB3
PPC64/TCG: Implement 'rfebb' instruction
target/ppc/power8-pmu.c: add PM_RUN_INST_CMPL (0xFA) event
target/ppc: enable PMU instruction count
target/ppc: enable PMU counter overflow with cycle events
target/ppc: PMU: update counters on MMCR1 write
target/ppc: PMU: update counters on PMCs r/w
target/ppc: PMU basic cycle count for pseries TCG
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
