At the moment "pseries" starts in SLOF which only expects the FDT blob
pointer in r3. As we are going to introduce a OpenFirmware support in
QEMU, we will be booting OF clients directly and these expect a stack
pointer in r1, Linux looks at r3/r4 for the initramdisk location
(although vmlinux can find this from the device tree but zImage from
distro kernels cannot).
This extends spapr_cpu_set_entry_state() to take more registers. This
should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20200310050733.29805-2-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In spapr_machine_init() we clamp the size of the RMA to 16GiB and the
comment saying why doesn't make a whole lot of sense. In fact, this was
done because the real mode handling code elsewhere limited the RMA in TCG
mode to the maximum value configurable in LPCR[RMLS], 16GiB.
But,
* Actually LPCR[RMLS] has been able to encode a 256GiB size for a very
long time, we just didn't implement it properly in the softmmu
* LPCR[RMLS] shouldn't really be relevant anyway, it only was because we
used to abuse the RMOR based translation mode in order to handle the
fact that we're not modelling the hypervisor parts of the cpu
We've now removed those limitations in the modelling so the 16GiB clamp no
longer serves a function. However, we can't just remove the limit
universally: that would break migration to earlier qemu versions, where
the 16GiB RMLS limit still applies, no matter how bad the reasons for it
are.
So, we replace the 16GiB clamp, with a clamp to a limit defined in the
machine type class. We set it to 16 GiB for machine types 4.2 and earlier,
but set it to 0 meaning unlimited for the new 5.0 machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Real Mode Area (RMA) is the part of memory which a guest can access
when in real (MMU off) mode. Of course, for a guest under KVM, the MMU
isn't really turned off, it's just in a special translation mode - Virtual
Real Mode Area (VRMA) - which looks like real mode in guest mode.
The mechanics of how this works when using the hash MMU (HPT) put a
constraint on the size of the RMA, which depends on the size of the
HPT. So, the latter part of spapr_setup_hpt_and_vrma() clamps the RMA
we advertise to the guest based on this VRMA limit.
There are several things wrong with this:
1) spapr_setup_hpt_and_vrma() doesn't actually clamp, it takes the minimum
of Node 0 memory size and the VRMA limit. That will *often* work the
same as clamping, but there can be other constraints on RMA size which
supersede Node 0 memory size. We have real bugs caused by this
(currently worked around in the guest kernel)
2) Some callers of spapr_setup_hpt_and_vrma() are in a situation where
we're past the point that we can actually advertise an RMA limit to the
guest
3) But most fundamentally, the VRMA limit depends on host configuration
(page size) which shouldn't be visible to the guest, but this partially
exposes it. This can cause problems with migration in certain edge
cases, although we will mostly get away with it.
In practice, this clamping is almost never applied anyway. With 64kiB
pages and the normal rules for sizing of the HPT, the theoretical VRMA
limit will be 4x(guest memory size) and so never hit. It will hit with
4kiB pages, where it will be (guest memory size)/4. However all mainstream
distro kernels for POWER have used a 64kiB page size for at least 10 years.
So, simply replace this logic with a check that the RMA we've calculated
based only on guest visible configuration will fit within the host implied
VRMA limit. This can break if running HPT guests on a host kernel with
4kiB page size. As noted that's very rare. There also exist several
possible workarounds:
* Change the host kernel to use 64kiB pages
* Use radix MMU (RPT) guests instead of HPT
* Use 64kiB hugepages on the host to back guest memory
* Increase the guest memory size so that the RMA hits one of the fixed
limits before the RMA limit. This is relatively easy on POWER8 which
has a 16GiB limit, harder on POWER9 which has a 1TiB limit.
* Use a guest NUMA configuration which artificially constrains the RMA
within the VRMA limit (the RMA must always fit within Node 0).
Previously, on KVM, we also temporarily reduced the rma_size to 256M so
that the we'd load the kernel and initrd safely, regardless of the VRMA
limit. This was a) confusing, b) could significantly limit the size of
images we could load and c) introduced a behavioural difference between
KVM and TCG. So we remove that as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
If a hot plug or unplug request is pending at CAS, we currently trigger
a CAS reboot, which severely increases the guest boot time. This is
because SLOF doesn't handle hot plug events and we had no way to fix
the FDT that gets presented to the guest.
We can do better thanks to recent changes in QEMU and SLOF:
- we now return a full FDT to SLOF during CAS
- SLOF was fixed to correctly detect any device that was either added or
removed since boot time and to update its internal DT accordingly.
The right solution is to process all pending hot plug/unplug requests
during CAS: convert hot plugged devices to cold plugged devices and
remove the hot unplugged ones, which is exactly what spapr_drc_reset()
does. Also clear all hot plug events that are currently queued since
they're no longer relevant.
Note that SLOF cannot currently populate hot plugged PCI bridges or PHBs
at CAS. Until this limitation is lifted, SLOF will reset the machine when
this scenario occurs : this will allow the FDT to be fully processed when
SLOF is started again (ie. the same effect as the CAS reboot that would
occur anyway without this patch).
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158257222352.4102917.8984214333937947307.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This series removes ad hoc RAM allocation API (memory_region_allocate_system_memory)
and consolidates it around hostmem backend. It allows to
* resolve conflicts between global -mem-prealloc and hostmem's "policy" option,
fixing premature allocation before binding policy is applied
* simplify complicated memory allocation routines which had to deal with 2 ways
to allocate RAM.
* reuse hostmem backends of a choice for main RAM without adding extra CLI
options to duplicate hostmem features. A recent case was -mem-shared, to
enable vhost-user on targets that don't support hostmem backends [1] (ex: s390)
* move RAM allocation from individual boards into generic machine code and
provide them with prepared MemoryRegion.
* clean up deprecated NUMA features which were tied to the old API (see patches)
- "numa: remove deprecated -mem-path fallback to anonymous RAM"
- (POSTPONED, waiting on libvirt side) "forbid '-numa node,mem' for 5.0 and newer machine types"
- (POSTPONED) "numa: remove deprecated implicit RAM distribution between nodes"
Introduce a new machine.memory-backend property and wrapper code that aliases
global -mem-path and -mem-alloc into automatically created hostmem backend
properties (provided memory-backend was not set explicitly given by user).
A bulk of trivial patches then follow to incrementally convert individual
boards to using machine.memory-backend provided MemoryRegion.
Board conversion typically involves:
* providing MachineClass::default_ram_size and MachineClass::default_ram_id
so generic code could create default backend if user didn't explicitly provide
memory-backend or -m options
* dropping memory_region_allocate_system_memory() call
* using convenience MachineState::ram MemoryRegion, which points to MemoryRegion
allocated by ram-memdev
On top of that for some boards:
* missing ram_size checks are added (typically it were boards with fixed ram size)
* ram_size fixups are replaced by checks and hard errors, forcing user to
provide correct "-m" values instead of ignoring it and continuing running.
After all boards are converted, the old API is removed and memory allocation
routines are cleaned up.
We currently don't support hotplug of devices between boot and CAS. If
this happens a CAS reboot is triggered. We detect this during CAS using
the spapr_drc_needed() function which is essentially a VMStateDescription
.needed callback. Even if the condition for CAS reboot happens to be the
same as for DRC migration, it looks wrong to piggyback a migration helper
for this.
Introduce a helper with slightly more explicit name and use it in both CAS
and DRC migration code. Since a subsequent patch will enhance this helper
to cover the case of hot unplug, let's go for spapr_drc_transient(). While
here convert spapr_hotplugged_dev_before_cas() to the "transient" wording as
well.
This doesn't change any behaviour.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158169248180.3465937.9531405453362718771.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows moving the kernel in the guest memory. The option is useful
for step debugging (as Linux is linked at 0x0); it also allows loading
grub which is normally linked to run at 0x20000.
This uses the existing kernel address by default.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20200203032943.121178-6-aik@ozlabs.ru>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch implements few of the necessary hcalls for the nvdimm support.
PAPR semantics is such that each NVDIMM device is comprising of multiple
SCM(Storage Class Memory) blocks. The guest requests the hypervisor to
bind each of the SCM blocks of the NVDIMM device using hcalls. There can
be SCM block unbind requests in case of driver errors or unplug(not
supported now) use cases. The NVDIMM label read/writes are done through
hcalls.
Since each virtual NVDIMM device is divided into multiple SCM blocks,
the bind, unbind, and queries using hcalls on those blocks can come
independently. This doesn't fit well into the qemu device semantics,
where the map/unmap are done at the (whole)device/object level granularity.
The patch doesnt actually bind/unbind on hcalls but let it happen at the
device_add/del phase itself instead.
The guest kernel makes bind/unbind requests for the virtual NVDIMM device
at the region level granularity. Without interleaving, each virtual NVDIMM
device is presented as a separate guest physical address range. So, there
is no way a partial bind/unbind request can come for the vNVDIMM in a
hcall for a subset of SCM blocks of a virtual NVDIMM. Hence it is safe to
do bind/unbind everything during the device_add/del.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Message-Id: <158131059899.2897.11515211602702956854.stgit@lep8c.aus.stglabs.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for NVDIMM devices for sPAPR. Piggyback on existing nvdimm
device interface in QEMU to support virtual NVDIMM devices for Power.
Create the required DT entries for the device (some entries have
dummy values right now).
The patch creates the required DT node and sends a hotplug
interrupt to the guest. Guest is expected to undertake the normal
DR resource add path in response and start issuing PAPR SCM hcalls.
The device support is verified based on the machine version unlike x86.
This is how it can be used ..
Ex :
For coldplug, the device to be added in qemu command line as shown below
-object memory-backend-file,id=memnvdimm0,prealloc=yes,mem-path=/tmp/nvdimm0,share=yes,size=1073872896
-device nvdimm,label-size=128k,uuid=75a3cdd7-6a2f-4791-8d15-fe0a920e8e9e,memdev=memnvdimm0,id=nvdimm0,slot=0
For hotplug, the device to be added from monitor as below
object_add memory-backend-file,id=memnvdimm0,prealloc=yes,mem-path=/tmp/nvdimm0,share=yes,size=1073872896
device_add nvdimm,label-size=128k,uuid=75a3cdd7-6a2f-4791-8d15-fe0a920e8e9e,memdev=memnvdimm0,id=nvdimm0,slot=0
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
[Early implementation]
Message-Id: <158131058078.2897.12767731856697459923.stgit@lep8c.aus.stglabs.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200219160953.13771-67-imammedo@redhat.com>
If user provided non-sense RAM size, board will complain and
continue running with max RAM size supported or sometimes
crash like this:
%QEMU -M bamboo -m 1
exec.c:1926: find_ram_offset: Assertion `size != 0' failed.
Aborted (core dumped)
Also RAM is going to be allocated by generic code, so it won't be
possible for board to fix things up for user.
Make it error message and exit to force user fix CLI,
instead of accepting non-sense CLI values.
That also fixes crash issue, since wrongly calculated size
isn't used to allocate RAM
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200219160953.13771-66-imammedo@redhat.com>
This patch includes migration support for machine check
handling. Especially this patch blocks VM migration
requests until the machine check error handling is
complete as these errors are specific to the source
hardware and is irrelevant on the target hardware.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Do not set FWNMI cap in post_load, now its done in .apply hook]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Message-Id: <20200130184423.20519-7-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds support in QEMU to handle "ibm,nmi-register"
and "ibm,nmi-interlock" RTAS calls.
The machine check notification address is saved when the
OS issues "ibm,nmi-register" RTAS call.
This patch also handles the case when multiple processors
experience machine check at or about the same time by
handling "ibm,nmi-interlock" call. In such cases, as per
PAPR, subsequent processors serialize waiting for the first
processor to issue the "ibm,nmi-interlock" call. The second
processor that also received a machine check error waits
till the first processor is done reading the error log.
The first processor issues "ibm,nmi-interlock" call
when the error log is consumed.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Register fwnmi RTAS calls in core_rtas_register_types()
where other RTAS calls are registered]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Message-Id: <20200130184423.20519-6-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Upon a machine check exception (MCE) in a guest address space,
KVM causes a guest exit to enable QEMU to build and pass the
error to the guest in the PAPR defined rtas error log format.
This patch builds the rtas error log, copies it to the rtas_addr
and then invokes the guest registered machine check handler. The
handler in the guest takes suitable action(s) depending on the type
and criticality of the error. For example, if an error is
unrecoverable memory corruption in an application inside the
guest, then the guest kernel sends a SIGBUS to the application.
For recoverable errors, the guest performs recovery actions and
logs the error.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Assume SLOF has allocated enough room for rtas error log]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200130184423.20519-5-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Memory error such as bit flips that cannot be corrected
by hardware are passed on to the kernel for handling.
If the memory address in error belongs to guest then
the guest kernel is responsible for taking suitable action.
Patch [1] enhances KVM to exit guest with exit reason
set to KVM_EXIT_NMI in such cases. This patch handles
KVM_EXIT_NMI exit.
[1] https://www.spinics.net/lists/kvm-ppc/msg12637.html
(e20bbd3d and related commits)
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200130184423.20519-4-ganeshgr@linux.ibm.com>
[dwg: #ifdefs to fix compile for 32-bit target]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce fwnmi an spapr capability and add a helper function
which tries to enable it, which would be used by following patch
of the series. This patch by itself does not change the existing
behavior.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[eliminate cap_ppc_fwnmi, add fwnmi cap to migration state
and reprhase the commit message]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200130184423.20519-3-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a model of the PCIe Host Bridge (PHB3) found on a POWER8
processor. It includes the PowerBus logic interface (PBCQ), IOMMU
support, a single PCIe Gen.3 Root Complex, and support for MSI and LSI
interrupt sources as found on a POWER8 system using the XICS interrupt
controller.
The POWER8 processor comes in different flavors: Venice, Murano,
Naple, each having a different number of PHBs. To make things simpler,
the models provides 3 PHB3 per chip. Some platforms, like the
Firestone, can also couple PHBs on the first chip to provide more
bandwidth but this is too specific to model in QEMU.
XICS requires some adjustment to support the PHB3 MSI. The changes are
provided here but they could be decoupled in prereq patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144506.11132-3-clg@kaod.org>
[dwg: Use device_class_set_props()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These changes introduces models for the PCIe Host Bridge (PHB4) of the
POWER9 processor. It includes the PowerBus logic interface (PBCQ),
IOMMU support, a single PCIe Gen.4 Root Complex, and support for MSI
and LSI interrupt sources as found on a POWER9 system using the XIVE
interrupt controller.
POWER9 processor comes with 3 PHB4 PEC (PCI Express Controller) and
each PEC can have several PHBs. By default,
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
Each PEC has a set "global" registers and some "per-stack" (per-PHB)
registers. Those are organized in two XSCOM ranges, the "Nest" range
and the "PCI" range, each range contains both some "PEC" registers and
some "per-stack" registers.
No default device layout is provided and PCI devices can be added on
any of the available PCIe Root Port (pcie.0 .. 2 of a Power9 chip)
with address 0x0 as the firwware (skiboot) only accepts a single
device per root port. To run a simple system with a network and a
storage adapters, use a command line options such as :
-device e1000e,netdev=net0,mac=C0:FF:EE:00:00:02,bus=pcie.0,addr=0x0
-netdev bridge,id=net0,helper=/usr/libexec/qemu-bridge-helper,br=virbr0,id=hostnet0
-device megasas,id=scsi0,bus=pcie.1,addr=0x0
-drive file=$disk,if=none,id=drive-scsi0-0-0-0,format=qcow2,cache=none
-device scsi-hd,bus=scsi0.0,channel=0,scsi-id=0,lun=0,drive=drive-scsi0-0-0-0,id=scsi0-0-0-0,bootindex=2
If more are needed, include a bridge.
Multi chip is supported, each chip adding its set of PHB4 controllers
and its PCI busses. The model doesn't emulate the EEH error handling.
This model is not ready for hotplug yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ clg: - numerous cleanups
- commit log
- fix for broken LSI support
- PHB pic printinfo
- large QOM rework ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144506.11132-2-clg@kaod.org>
[dwg: Use device_class_set_props()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For devices that cannot be statically initialized, implement a
get_dt_compatible() callback that allows us to ask the device for
the 'compatible' value.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-3-stefanb@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the "hb-mode" option is activated on the powernv machine, the
firmware is mapped at 0x8000000 and the HRMOR of the HW threads are
set to the same address.
The PNOR mapping on the FW address space of the LPC bus is left enabled
to let the firmware load any other images required to boot the host.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144154.10170-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It's been deprecated since QEMU v3.1. The 40p machine should be
used nowadays instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200114114617.28854-1-thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
blk_getlength() returns an int64_t but the result is stored in a
uint32_t. Errors (negative values) won't be caught by the check in
pnv_pnor_realize() and blk_blockalign() will allocate a very large
buffer in such cases.
Fixes Coverity issue CID 1412226.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200107171809.15556-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And use it instead of reaching out to the machine. This allows to get
rid of pnv_get_chip().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used in subsequent patches to access the XIVE associated to
a TCTX without reaching out to the machine through qdev_get_machine().
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[ groug: - split patch
- write subject and changelog ]
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows to get rid of a call to qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Set it at chip creation and forward it to the cores. This allows to drop
a call to qdev_get_machine().
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to get rid of qdev_get_machine(), first add a pointer to the
XIVE fabric under the XIVE router and make it configurable through a
QOM link property.
Configure it in the spapr and pnv machine. In the case of pnv, the XIVE
routers are under the chip, so this is done with a QOM alias property of
the POWER9 pnv chip.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200106145645.4539-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE router base class currently inherits an empty realize hook
from the sysbus device base class, but it will soon implement one
of its own to perform some sanity checks. Do the preliminary plumbing
to have it called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
POWER8 is the only chip using the XICS interface. Add a "xics" link
and a XICSFabric attribute under this chip to remove the use of
qdev_get_machine()
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200106145645.4539-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE router base class currently inherits an empty realize hook
from the sysbus device base class, but it will soon implement one
of its own to perform some sanity checks. Do the preliminary plumbing
to have it called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191219181155.32530-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623844102.360005.12070225703151669294.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XSCOM bus is implemented with a QOM interface, which is mostly
generic from a CPU type standpoint, except for the computation of
addresses on the Pervasive Connect Bus (PCB) network. This is handled
by the pnv_xscom_pcba() function with a switch statement based on
the chip_type class level attribute of the CPU chip.
This can be achieved using QOM. Also the address argument is masked with
PNV_XSCOM_SIZE - 1, which is for POWER8 only. Addresses may have different
sizes with other CPU types. Have each CPU chip type handle the appropriate
computation with a QOM xscom_pcba() method.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623843543.360005.13996472463887521794.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
They aren't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623842986.360005.1787401623906380181.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the
"compatible" property. Just pass the compat string and its size as
arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623842430.360005.9513965612524265862.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since pnv_dt_xscom() is called from chip specific dt_populate() hooks,
it shouldn't have to guess the chip type in order to populate the "reg"
property. Just pass the base address and address size as arguments.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841868.360005.17577624823547136435.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_chip_core_realize() function configures the XSCOM MMIO subregion
for each core of a single chip. The base address of the subregion depends
on the CPU type. Its computation is currently open-code using the
pnv_chip_is_powerXX() helpers. This can be achieved with QOM. Introduce
a method for this in the base chip class and implement it in child classes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623841311.360005.4705705734873339545.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_pic_print_info() callback checks the type of the chip in order
to forward to the request appropriate interrupt controller. This can
be achieved with QOM. Introduce a method for this in the base chip class
and implement it in child classes.
This also prepares ground for the upcoming interrupt controller of POWER10
chips.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623840755.360005.5002022339473369934.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
They aren't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623840200.360005.1300941274565357363.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We add an extra node to advertise power management on some machines,
namely powernv9 and powernv10. This is achieved by using the
pnv_is_power9() and pnv_is_power10() helpers.
This can be achieved with QOM. Add a method to the base class for
powernv machines and have it implemented by machine types that
support power management instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839642.360005.9243510140436689941.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pnv_dt_create() function generates different contents for the
"compatible" property of the root node in the DT, depending on the
CPU type. This is open coded with multiple ifs using pnv_is_powerXX()
helpers.
It seems cleaner to achieve with QOM. Introduce a base class for the
powernv machine and a compat attribute that each child class can use
to provide the value for the "compatible" property.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623839085.360005.4046508784077843216.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in small fix Greg spotted after posting]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It isn't used anymore.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623838530.360005.15470128760871845396.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Service Interface (PSI) model has a chip_type class level
attribute, which is used to generate the content of the "compatible" DT
property according to the CPU type.
Since the PSI model already has specialized classes for each supported
CPU type, it seems cleaner to achieve this with QOM. Provide the content
of the "compatible" property with a new class level attribute.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157623837974.360005.14706607446188964477.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <157623837421.360005.412120366652768311.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC common area is mapped at a unique address on the system and
each OCC is assigned a segment to expose its sensor data :
-------------------------------------------------------------------------
| Start (Offset from | End | Size |Description |
| BAR2 base address) | | | |
-------------------------------------------------------------------------
| 0x00580000 | 0x005A57FF |150kB |OCC 0 Sensor Data Block|
| 0x005A5800 | 0x005CAFFF |150kB |OCC 1 Sensor Data Block|
| : | : | : | : |
| 0x00686800 | 0x006ABFFF |150kB |OCC 7 Sensor Data Block|
| 0x006AC000 | 0x006FFFFF |336kB |Reserved |
-------------------------------------------------------------------------
Maximum size is 1.5MB.
We could define a "OCC common area" memory region at the machine level
and sub regions for each OCC. But it adds some extra complexity to the
models. Fix the current layout with a simpler model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PBA bridge unit (Power Bus Access) connects the OCC (On Chip
Controller) to the Power bus and System Memory. The PBA is used to
gather sensor data, for power management, for sleep states, for
initial boot, among other things.
The PBA logic provides a set of four registers PowerBus Access Base
Address Registers (PBABAR0..3) which map the OCC address space to the
PowerBus space. These registers are setup by the initial FW and define
the PowerBus Range of system memory that can be accessed by PBA.
The current modeling of the PBABAR registers is done under the common
XSCOM handlers. We introduce a specific XSCOM regions for these
registers and fix :
- BAR sizes and BAR masks
- The mapping of the OCC common area. It is common to all chips and
should be mapped once. We will address per-OCC area in the next
change.
- OCC common area is in BAR 3 on P8
Inspired by previous work of Balamuruhan S <bala24@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191211082912.2625-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PnvXScomInterface is an interface instance. It should never be
dereferenced. Drop the dummy type definition for extra safety,
which is the common practice with QOM interfaces.
While here also convert the bogus OBJECT_CHECK() to INTERFACE_CHECK().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157608025541.186670.1577861507610404326.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Utilisation of Resources Register (PURR) and Scaled
Processor Utilisation of Resources Register (SPURR) provide an estimate
of the resources used by the thread, present on POWER7 and later
processors.
Currently the [S]PURR registers simply count at the rate of the
timebase.
Preserve this behaviour but rework the implementation to store an offset
like the timebase rather than doing the calculation manually. Also allow
hypervisor write access to the register along with the currently
available read access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The virtual timebase register (VTB) is a 64-bit register which
increments at the same rate as the timebase register, present on POWER8
and later processors.
The register is able to be read/written by the hypervisor and read by
the supervisor. All other accesses are illegal.
Currently the VTB is just an alias for the timebase (TB) register.
Implement the VTB so that is can be read/written independent of the TB.
Make use of the existing method for accessing timebase facilities where
by the compensation is stored and used to compute the value on reads/is
updated on writes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[ clg: rebased on current ppc tree ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191128134700.16091-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Same a POWER9, only the MMIO window changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER10 PSIHB controller is very similar to the one on POWER9. We
should probably introduce a common PnvPsiXive object.
The ESB page size should be changed to 64k when P10 support is ready.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191205184454.10722-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
