I'm not familiar with this device, but I'm fairly certain the writel handler is
not supposed to recurse.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5995 c046a42c-6fe2-441c-8c8c-71466251a162
Use the defines added by the previous patch in the virtio drivers.
Also remove the pointless vendor and device args from the
virtio_blk_init() function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5987 c046a42c-6fe2-441c-8c8c-71466251a162
This sets a default PCI subsystem ID for all emulated PCI devices. PCI
specs require this, so do it.
In many cases it is enougth to know the PCI ID to handle a device
correctly. Sometimes a device driver must identify the exact piece of
hardware (via PCI Subsystem ID) though.
What does this patch to qemu devices:
Right now the emulated PCI devices have no PCI subsystem ID, only the
PCI ID. The discussed patch sets a default PCI subsystem ID for all
emulated devices. Which will make the qemu devices look pretty much
like in the laptop case: all PCI subsystem IDs will point to qemu by
default.
If a driver emulates a very specific piece of hardware where it has to
emulate more than just the PCI chip, it can overwrite the PCI subsystem
ID without problems. The es1370 driver does that for example.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5986 c046a42c-6fe2-441c-8c8c-71466251a162
Fix compiler warning on OSX, reported by Andreas Faerber.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5982 c046a42c-6fe2-441c-8c8c-71466251a162
fw_cfg_add_callback() checks if key has FW_CFG_WRITE_CHANNEL bit set
after masking the key with FW_CFG_ENTRY_MASK.
But as FW_CFG_ENTRY_MASK is ~(FW_CFG_WRITE_CHANNEL | FW_CFG_ARCH_LOCAL),
the bit is never set and function exits.
This patch corrects this by checking the bit before masking the value.
Signed-by-off: Laurent Vivier <Laurent.Vivier@bull.net>
Acked-by: Gleb Natapov <gleb@redhat.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5978 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds support for 64-bit Block Move instructions. There are multiple
modes for 64-bit Block moves, direct, indirect, and table indirect. This patch
implements Direct and Table indirect moves which are needed by 64-bit windows
and SYM_CONF_DMA_ADDRESSING_MODE=2 for the Linux sym53c8xx_2 driver respectively.
Two helper functions are included to check which mode the guest is using. For
64-bit direct moves, we fetch a 3rd DWORD and store the value in the DBMS
register. For Table Indirect moves, we look into the table for which register
contains the upper 32-bits of the 64-bit address. This selector value indicates
which register to pull the value from and into dnad64 register.
Finally, lsi_do_dma is updated to use the approriate register to build a 64-bit
DMA address if required.
With this patch, Windows XP x64, 2003 SP2 x64, can now install to scsi devices.
Linux SYM_CONF_DMA_ADDRESSING_MODE=2 need a quirk fixup in Patch 4 to function
properly.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5969 c046a42c-6fe2-441c-8c8c-71466251a162
Current implementation of memory-mapped i8042 controller is atm
implemented with an interface shift (it_shift) parameter, like most all
memory-mapped devices in Qemu.
However, this isn't suitable for MIPS Magnum, where i8042 controller is at
0x80005000 up to 0x80005fff.
Thomas Bogendoerfer (from #mipslinux) tested the behaviour of a real
machine, and found that odd addresses are for status/command register, and
even addresses for data register.
Attached patch implements this behaviour by replacing the it_shift
parameter by a mask one.
Incidentally, keyboard now works on OpenBSD 2.3, which accesses i8042
controller at 0x80005060 and 0x80005061.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5962 c046a42c-6fe2-441c-8c8c-71466251a162
MMIO exits are more expensive in KVM or Xen than in QEMU because they
involve, at least, privilege transitions. However, MMIO write
operations can be effectively batched if those writes do not have side
effects.
Good examples of this include VGA pixel operations when in a planar
mode. As it turns out, we can get a nice boost in other areas too.
Laurent mentioned a 9.7% performance boost in iperf with the coalesced
MMIO changes for the e1000 when he originally posted this work for KVM.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5961 c046a42c-6fe2-441c-8c8c-71466251a162
Attached patch adds a reset handler to parallel port, so it gets correct
register values after a reset.
(Hervé Poussineau)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5942 c046a42c-6fe2-441c-8c8c-71466251a162
This patch simply implement one register of SH4's SCI := Serial Communication Interface.
R2D evaluation board uses SCI for SPI connection. So, Linux kernel for R2D with
default configuration causes a QEMU assertion failure when it initializes SPI driver.
This patch avoids it and reduces the kernel config modification work for QEMU.
Completing SCI implementation task is left. Other board support is desirable to confirm
this task, which uses SCI for a serial terminal.
(Shin-ichiro KAWASAKI)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5939 c046a42c-6fe2-441c-8c8c-71466251a162
Main purpose of this is to delete
*physical = address & 0x1fffffff;
at target-sh4/helper.c:449, using new mmio rule introduced by #5849
This masking is a nice trick to realize P4/A7 duality of SH registers.
But, IMHO, it is logically wrong.
Most of SH4 cpu control registers in P4 area(0xfc000000...0xffffffff) have
one more address called A7 which is usually P4 address with upper 3bits masked.
This is an address only appears in TLB's physical address part.
Current code use trick writing drivers as if they are really in A7
(that's why you see many *_A7 in hw/sh*.c), and using translation P4 to A7.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5935 c046a42c-6fe2-441c-8c8c-71466251a162
Fixes to be needed for commit #5849 "Change MMIO callbacks..."
hw/sh7750.c:
- Divide region of CPU control registers to avoid overlapping
to peripheral modules.
- Delete unused var "icr", which had moved to hw/sh_intc.c.
hw/sm501.c:
- Merge non page aligned palette registers into the region of
control registers.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5934 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds pci support to sh/r2d board.
This is the first user of PCIC support I formerly sent.
PCIC actually is inside of chip with CPU core on SH7751.
But, this code is written as if SH7750 and PCIC are on board.
I care little about physical device boundary, but fitting with qemu's
design.
This patch also adds some BSC (Bus State Controller) registers,
because PCI device driver software have to accesses them.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5932 c046a42c-6fe2-441c-8c8c-71466251a162
This adds IRQ controller in FPGA on r2d, and use it for CF.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5926 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds IRL(4bit encoded 15 level interrupt input) support
to SH using qemu_irq as a multi level (!=on/off) signal.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5925 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds emulation for a CompactFlash on sh4/r2d board.
The device is CF, but wired to be worked as True-IDE mode, and connected
directly to SH bus. So, this code is to support generally mmio based
IDEs which are supported by "pata_platform" driver in linux kernel.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5924 c046a42c-6fe2-441c-8c8c-71466251a162
Openserver 5.0.5 sends an Inquiry command to the emulated SCSI disk
expecting a response length of 40 bytes. Currently the response to an
Inquiry command is hardcoded to 36 bytes. When receiving a response of
length 36 instead of 40 Openserver panics.
Modifications to original patch based on feedback from Ryan Harper and Paul
Brook. Thanks guys.
Signed-off-by: Justin Chevrier <address@hidden>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5903 c046a42c-6fe2-441c-8c8c-71466251a162
Basically after each DMA transfer the Openserver driver would issue an
empty (0) SCRIPTS opcode. As the opcode is essentially a NOP it has no
second DWORD and therefore the DSP should only be incremented by 4 bytes
instead of the 8 bytes we currently do.
Here's a snippet of the log:
lsi_scsi: Data ready tag=0x100d9 len=16384
...
lsi_scsi: SCRIPTS dsp=068c5e50 opcode 01000400 arg 07a09000
lsi_scsi: DMA addr=0x07a09000 len=1024
lsi_scsi: SCRIPTS dsp=068c5e58 opcode 00000000 arg 01000400
lsi_scsi: Wrong phase got 1 expected 0
Note the 2nd DWORD after the empty opcode; the next opcode in the DMA
transfer sequence. As can be expected the address after that has the next
DMA address to use.
After the attached patch the DMA transfer is able to complete successfully:
lsi_scsi: SCRIPTS dsp=068c5e50 opcode 01000400 arg 07a0d000
lsi_scsi: DMA addr=0x07a0d000 len=1024
lsi_scsi: SCRIPTS dsp=068c5e5c opcode 01000400 arg 07a0d400
lsi_scsi: DMA addr=0x07a0d400 len=1024
...
Tested againsted Openserver 5.0.5 and Debian ARM.
Signed-off-by: Justin Chevrier <address@hidden>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5902 c046a42c-6fe2-441c-8c8c-71466251a162
This way the registers will only be visible at the given offset instead of
every 0x100 bytes.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5899 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5898 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5897 c046a42c-6fe2-441c-8c8c-71466251a162
Vectored IO APIs will require some sort of vector argument. It makes sense to
use struct iovec and just define it globally for Windows.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5889 c046a42c-6fe2-441c-8c8c-71466251a162
For backward operations, dstpitch and srcpitch can
be negative. This leads BLTUNSAFE macro into an
overflow, and as a result, it avoids performing
operations that are perfectly valid.
The visible effect that led to that patch was the gnome-panel
bar in Fedora10. Before this patch, you could see garbage
clobbering a big portion of the bar.
After this patch, this garbage is gone.
Signed-off-by: Glauber Costa <glommer@redhat.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5880 c046a42c-6fe2-441c-8c8c-71466251a162
qemu_get_clock() returns a structure containing the time the user wants
to be set (either UTC time, a local time, or a given date). Use mktimegm()
instead of mktime() to convert it into POSIX time without taking the host
timezone into account.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5878 c046a42c-6fe2-441c-8c8c-71466251a162
Windows does not have sys/uio.h and does not have err.h.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5877 c046a42c-6fe2-441c-8c8c-71466251a162
...and fix a bug, the implementation in hw/apic.c was wrong.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5876 c046a42c-6fe2-441c-8c8c-71466251a162
This adds a VirtIO based balloon driver. It uses madvise() to actually balloon
the memory when possible.
Until 2.6.27, KVM forced memory pinning so we must disable ballooning unless the
kernel actually supports it when using KVM. It's always safe when using TCG.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5874 c046a42c-6fe2-441c-8c8c-71466251a162
TARGET_PAGE_SIZE should only be used internal to qemu, not in guest/host
interfaces. The virtio frontend code in Linux uses two constants (PFN shift
and vring alignment) for the interface, so update qemu to match.
I've tested this with PowerPC KVM and confirmed that it fixes virtio problems
when using non-TARGET_PAGE_SIZE pages in the guest.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5871 c046a42c-6fe2-441c-8c8c-71466251a162
Virtio-blk is a paravirtual block device based on VirtIO. It can be used by
specifying the if=virtio parameter to the -drive parameter.
When using -enable-kvm, it can achieve very good performance compared to IDE or
SCSI.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5870 c046a42c-6fe2-441c-8c8c-71466251a162
