This change fixes the CFI query responses to handle NOR device
widths that are different from the bank width. Support is also
added for multi-width devices in a x8 configuration. This is
typically x8/x16 devices, but the CFI specification mentions
x8/x32 devices so those should be supported as well if they
exist.
The query response data is now replicated per-device in the bank,
and is adjusted for x16 or x32 parts configured in x8 mode.
The existing code is left in place for boards that have not
been updated to specify an explicit device_width. The VExpress
board has been updated in an earlier patch in this series so
this is the only board currently affected.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-7-git-send-email-roy.franz@linaro.org
[PMM: fixed a few formatting nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For handling CFI and device ID reads, we need to not only know the
width that a NOR flash device is configured for, but also its maximum
width. The maximum width addressing mode is used for multi-width
parts no matter which width they are configured for. The most common
case is x16 parts that also support x8 mode. When configured for x8
operation these devices respond to CFI and device ID requests differently
than native x8 NOR parts.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-6-git-send-email-roy.franz@linaro.org
[PMM: Added comment explaining the semantics of width vs device-width
vs max-device-width]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we know how wide each flash device that makes up the bank is,
return status for each device in the bank. Leave existing code
that treats 32 bit wide banks as composed of two 16 bit devices as otherwise
we may break configurations that do not set the device_width propery.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-4-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The width of the devices that make up the flash interface
is required to mask certain commands, in particular the
write length for buffered writes. This length will be presented
to each device on the interface by the program writing the flash,
and the flash emulation code needs to be able to determine
the length of the write as recieved by each flash device.
The device-width defaults to the bank width which should
maintain existing behavior for platforms that don't need
this change.
This change is required to support buffered writes on the
vexpress platform that has a 32 bit flash interface with 2
16 bit devices on it.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-3-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the 'width' member of the pflash_t structure
in preparation for adding a bank_width member.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1386279359-32286-2-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The firmware commonly used with MIPS Malta boards (YAMON) reads the
status of the pflash with a 32bit memory access. On real hardware
this results in the status byte being mirrored in the upper 16 bits
of the read value. For example if the status byte is represented by
SS then the hardware reads 0x00SS00SS. The YAMON firmware compares the
status against 32bit values expecting the mirrored value and fails
without it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Introduce type constant and replace FROM_SYSBUS().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
"Readable" is a very unfortunate name for this flag because even a
rom_device region will always be readable from the guest POV. What
differs is the mapping, just like the comments had to explain already.
Also, readable could currently be understood as being a generic region
flag, but it only applies to rom_device regions.
So rename the flag and the function to modify it after the original term
"ROMD" which could also be interpreted as "ROM direct", i.e. ROM mode
with direct access. In any case, the scope of the flag is clearer now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>