Each board in mps2-tz.c specifies a RAMInfo[] array providing
information about each RAM in the board. The .mpc field of the
RAMInfo struct specifies which MPC, if any, the RAM is attached to.
We already assert if the array doesn't have any entry for an MPC, but
we don't diagnose the error of using the same MPC number twice (which
is quite easy to do by accident if copy-and-pasting structure
entries).
Enhance find_raminfo_for_mpc() so that it detects multiple entries
for the MPC as well as missing entries.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-3-peter.maydell@linaro.org
The AN524 has three MPCs: one for the BRAM, one for the QSPI flash,
and one for the DDR. We incorrectly set the .mpc field in the
RAMInfo struct for the SRAM block to 1, giving it the same MPC we are
using for the QSPI. The effect of this was that the QSPI didn't get
mapped into the system address space at all, via an MPC or otherwise,
and guest programs which tried to read from the QSPI would get a bus
error. Correct the SRAM RAMInfo to indicate that it does not have an
associated MPC.
Fixes: 25ff112a8c ("hw/arm/mps2-tz: Add new mps3-an524 board")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-2-peter.maydell@linaro.org
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
The AN505 and AN521 don't have any read-only memory, but the AN524
does; add a flag to ROMInfo to mark a region as ROM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-19-peter.maydell@linaro.org
Instead of hardcoding the MachineClass default_ram_size and
default_ram_id fields, set them on class creation by finding the
entry in the RAMInfo array which is marked as being the QEMU system
RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-18-peter.maydell@linaro.org
The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
The AN524 has a different SYSCLK frequency from the AN505 and AN521;
make the SYSCLK frequency a field in the MPS2TZMachineClass rather
than a compile-time constant so we can support the AN524.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-2-peter.maydell@linaro.org
Remove all the code that sets frequency properties on the CMSDK
timer, dualtimer and watchdog devices and on the ARMSSE SoC device:
these properties are unused now that the devices rely on their Clock
inputs instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-24-peter.maydell@linaro.org
Message-id: 20210121190622.22000-24-peter.maydell@linaro.org
While we transition the ARMSSE code from integer properties
specifying clock frequencies to Clock objects, we want to have the
device provide both at once. We want the final name of the main
input Clock to be "MAINCLK", following the hardware name.
Unfortunately creating an input Clock with a name X creates an
under-the-hood QOM property X; for "MAINCLK" this clashes with the
existing UINT32 property of that name.
Rename the UINT32 property to MAINCLK_FRQ so it can coexist with the
MAINCLK Clock; once the transition is complete MAINCLK_FRQ will be
deleted.
Commit created with:
perl -p -i -e 's/MAINCLK/MAINCLK_FRQ/g' hw/arm/{armsse,mps2-tz,musca}.c include/hw/arm/armsse.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-11-peter.maydell@linaro.org
Message-id: 20210121190622.22000-11-peter.maydell@linaro.org
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
From 'Application Note AN521', chapter 4.7:
The SMM implements four SBCon serial modules:
One SBCon module for use by the Color LCD touch interface.
One SBCon module to configure the audio controller.
Two general purpose SBCon modules, that connect to the
Expansion headers J7 and J8, are intended for use with the
V2C-Shield1 which provide an I2C interface on the headers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-15-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
The callers of sysbus_init_child_obj() commonly pass either &child,
sizeof(child), or pchild, sizeof(*pchild). Tidy up the few that use
something else instead, mostly to keep future commits simpler.
Coccinelle script:
@@
expression parent, propname, type;
expression child;
type T;
T proxy;
@@
(
sysbus_init_child_obj(parent, propname, &child, sizeof(child), type)
|
sysbus_init_child_obj(parent, propname, child, sizeof(*child), type)
|
- sysbus_init_child_obj(parent, propname, child, sizeof(proxy), type)
+ sysbus_init_child_obj(parent, propname, child, sizeof(*child), type)
)
This script is *unsound*: for each change we need to verify the
@childsize argument stays the same. I did.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-44-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
By using the TYPE_* definitions for devices, we can:
- quickly find where devices are used with 'git-grep'
- easily rename a device (one-line change).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200428154650.21991-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
PS:
while at it add check for user supplied RAM size and error
out if it mismatches board expected value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200219160953.13771-23-imammedo@redhat.com>
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As explained in commit aff39be0ed97:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As explained in commit aff39be0ed97:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let the MPS2 boards adopt the cpu core, the FPGA and the SCC children.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-16-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-12-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
