During 'qemu-img create ... 2>&1', if --quiet is not in force, we can
end up with buffered I/O in stdout that was produced before failure,
but which appears in output after failure. This is confusing; the fix
is to flush stdout prior to attempting anything that might produce an
error message. Several iotests demonstrate the resulting ordering
change now that the merged outputs now reflect chronology. (An even
better fix would be to avoid printf from within block.c altogether,
but that's much more invasive...)
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200706203954.341758-2-eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Especially when O_DIRECT is used with image files so that the page cache
indirection can't cause a merge of allocating requests, the file will
fragment on the file system layer, with a potentially very small
fragment size (this depends on the requests the guest sent).
On Linux, fragmentation can be reduced by setting an extent size hint
when creating the file (at least on XFS, it can't be set any more after
the first extent has been allocated), basically giving raw files a
"cluster size" for allocation.
This adds a create option to set the extent size hint, and changes the
default from not setting a hint to setting it to 1 MB. The main reason
why qcow2 defaults to smaller cluster sizes is that COW becomes more
expensive, which is not an issue with raw files, so we can choose a
larger size. The tradeoff here is only potentially wasted disk space.
For qcow2 (or other image formats) over file-posix, the advantage should
even be greater because they grow sequentially without leaving holes, so
there won't be wasted space. Setting even larger extent size hints for
such images may make sense. This can be done with the new option, but
let's keep the default conservative for now.
The effect is very visible with a test that intentionally creates a
badly fragmented file with qemu-img bench (the time difference while
creating the file is already remarkable) and then looks at the number of
extents and the time a simple "qemu-img map" takes.
Without an extent size hint:
$ ./qemu-img create -f raw -o extent_size_hint=0 ~/tmp/test.raw 10G
Formatting '/home/kwolf/tmp/test.raw', fmt=raw size=10737418240 extent_size_hint=0
$ ./qemu-img bench -f raw -t none -n -w ~/tmp/test.raw -c 1000000 -S 8192 -o 0
Sending 1000000 write requests, 4096 bytes each, 64 in parallel (starting at offset 0, step size 8192)
Run completed in 25.848 seconds.
$ ./qemu-img bench -f raw -t none -n -w ~/tmp/test.raw -c 1000000 -S 8192 -o 4096
Sending 1000000 write requests, 4096 bytes each, 64 in parallel (starting at offset 4096, step size 8192)
Run completed in 19.616 seconds.
$ filefrag ~/tmp/test.raw
/home/kwolf/tmp/test.raw: 2000000 extents found
$ time ./qemu-img map ~/tmp/test.raw
Offset Length Mapped to File
0 0x1e8480000 0 /home/kwolf/tmp/test.raw
real 0m1,279s
user 0m0,043s
sys 0m1,226s
With the new default extent size hint of 1 MB:
$ ./qemu-img create -f raw -o extent_size_hint=1M ~/tmp/test.raw 10G
Formatting '/home/kwolf/tmp/test.raw', fmt=raw size=10737418240 extent_size_hint=1048576
$ ./qemu-img bench -f raw -t none -n -w ~/tmp/test.raw -c 1000000 -S 8192 -o 0
Sending 1000000 write requests, 4096 bytes each, 64 in parallel (starting at offset 0, step size 8192)
Run completed in 11.833 seconds.
$ ./qemu-img bench -f raw -t none -n -w ~/tmp/test.raw -c 1000000 -S 8192 -o 4096
Sending 1000000 write requests, 4096 bytes each, 64 in parallel (starting at offset 4096, step size 8192)
Run completed in 10.155 seconds.
$ filefrag ~/tmp/test.raw
/home/kwolf/tmp/test.raw: 178 extents found
$ time ./qemu-img map ~/tmp/test.raw
Offset Length Mapped to File
0 0x1e8480000 0 /home/kwolf/tmp/test.raw
real 0m0,061s
user 0m0,040s
sys 0m0,014s
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200707142329.48303-1-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The actual disk space used by an image can vary between filesystems and
depending on other settings like an extent size hint. Replace the one
call of "$QEMU_IMG info" and the associated one-off sed filter with the
more standard "_img_info" and the standard filter from common.filter.
Apart from turning "vmdk" into "IMGFMT" and changing the placeholder for
cid fields, this only removes the "disk size" line.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Not only is it a bit stupid to try to filter multi-line "Formatting"
output (because we only need it for a single test, which can easily be
amended to no longer need it), it is also problematic when there can be
output after a "Formatting" line that we do not want to filter as if it
were part of it.
So rename _filter_img_create to _do_filter_img_create, let it filter
only a single line, and let _filter_img_create loop over all input
lines, calling _do_filter_img_create only on those that match
/^Formatting/ (basically, what _filter_img_create_in_qmp did already).
(And fix 020 to work with that.)
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200709110205.310942-1-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Otherwise the result is basically unpredictable.
(Note that the precise environment variable to control sorting order is
LC_COLLATE, but LC_ALL overrides LC_COLLATE, and we do not want the
sorting order to be messed up if LC_ALL is set in the environment.)
Reported-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20200710163253.381630-3-mreitz@redhat.com>
In case when get_image_offset() returns -1, we do zero out the
corresponding chunk of qiov. So, this should be reported as ZERO.
Note that this changes visible output of "qemu-img map --output=json"
and "qemu-io -c map" commands. For qemu-img map, the change is obvious:
we just mark as zero what is really zero. For qemu-io it's less
obvious: what was unallocated now is allocated.
There is an inconsistency in understanding of unallocated regions in
Qemu: backing-supporting format-drivers return 0 block-status to report
go-to-backing logic for this area. Some protocol-drivers (iscsi) return
0 to report fs-unallocated-non-zero status (i.e., don't occupy space on
disk, read result is undefined).
BDRV_BLOCK_ALLOCATED is defined as something more close to
go-to-backing logic. Still it is calculated as ZERO | DATA, so 0 from
iscsi is treated as unallocated. It doesn't influence backing-chain
behavior, as iscsi can't have backing file. But it does influence
"qemu-io -c map".
We should solve this inconsistency at some future point. Now, let's
just make backing-not-supporting format drivers (vdi in the previous
patch and vpc now) to behave more like backing-supporting drivers
and not report 0 block-status. More over, returning ZERO status is
absolutely valid thing, and again, corresponds to how the other
format-drivers (backing-supporting) work.
After block-status update, it never reports 0, so setting
unallocated_blocks_are_zero doesn't make sense (as the only user of it
is bdrv_co_block_status and it checks unallocated_blocks_are_zero only
for unallocated areas). Drop it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200528094405.145708-5-vsementsov@virtuozzo.com>
[mreitz: qemu-io -c map as used by iotest 146 now reports everything as
allocated; in order to make the test do something useful, we
use qemu-img map --output=json now]
Signed-off-by: Max Reitz <mreitz@redhat.com>
This commit adds two tests that cover the
new blockdev-amend functionality of luks and qcow2 driver
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[mreitz: Let 295 verify that LUKS works; drop 295 and 296 from the auto
group]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-20-mreitz@redhat.com>
This commit adds two tests, which test the new amend interface
of both luks raw images and qcow2 luks encrypted images.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[mreitz: Let 293 verify that LUKS works; drop $(seq) usage from 293;
drop 293 and 294 from the auto group]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-16-mreitz@redhat.com>
Now that we have all the infrastructure in place,
wire it in the qcow2 driver and expose this to the user.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200608094030.670121-9-mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Some qcow2 create options can't be used for amend.
Remove them from the qcow2 create options and add generic logic to detect
such options in qemu-img
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[mreitz: Dropped some iotests reference output hunks that became
unnecessary thanks to
"iotests: Make _filter_img_create more active"]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-12-mreitz@redhat.com>
Whenever running an iotest for the luks format, we should check whether
luks actually really works.
Tests that try to create luks-encrypted qcow2 images should do the same.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-7-mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Similar to _require_working_luks for bash tests, these functions can be
used to check whether our luks driver can actually create images.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-6-mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
This function will be used by the next patch, which intends to check
both the exit code and qemu-img's output.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-5-mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
[mreitz: Rebased on 49438972b8]
Signed-off-by: Max Reitz <mreitz@redhat.com>
That the luks driver is present is little indication on whether it is
actually working. Without the crypto libraries linked in, it does not
work. So add this function, which tries to create a luks image to see
whether that actually works.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-4-mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
This allows more tests to be able to have same output on both qcow2 luks encrypted images
and raw luks images
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200625125548.870061-3-mreitz@redhat.com>
Right now, _filter_img_create just filters out everything that looks
format-dependent, and applies some filename filters. That means that we
have to add another filter line every time some format gets a new
creation option. This can be avoided by instead discarding everything
and just keeping what we know is format-independent (format, size,
backing file, encryption information[1], preallocation) or just
interesting to have in the reference output (external data file path).
Furthermore, we probably want to sort these options. Format drivers are
not required to define them in any specific order, so the output is
effectively random (although this has never bothered us until now). We
need a specific order for our reference outputs, though. Unfortunately,
just using a plain "sort" would change a lot of existing reference
outputs, so we have to pre-filter the option keys to keep our existing
order (fmt, size, backing*, data, encryption info, preallocation).
Finally, this makes it difficult for _filter_img_create to automagically
work for QMP output. Thus, this patch adds a separate
_filter_img_create_for_qmp function that echos every line verbatim that
does not start with "Formatting", and pipes those "Formatting" lines to
_filter_img_create.
[1] Actually, the only thing that is really important is whether
encryption is enabled or not. A patch by Maxim thus removes all
other "encrypt.*" options from the output:
https://lists.nongnu.org/archive/html/qemu-block/2020-06/msg00339.html
But that patch needs to come later so we can get away with changing
as few reference outputs in this patch here as possible.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200625125548.870061-2-mreitz@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
When resizing an image with qcow2_co_truncate() using the falloc or
full preallocation modes the code assumes that both the old and new
sizes are cluster-aligned.
There are two problems with this:
1) The calculation of how many clusters are involved does not always
get the right result.
Example: creating a 60KB image and resizing it (with
preallocation=full) to 80KB won't allocate the second cluster.
2) No copy-on-write is performed, so in the previous example if
there is a backing file then the first 60KB of the first cluster
won't be filled with data from the backing file.
This patch fixes both issues.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20200617140036.20311-1-berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Commit 96927c744 replaced qdev_init_nofail() call by
isa_realize_and_unref() which has a different error
message. Update the test output accordingly.
Gitlab CI error after merging b77b5b3dc7:
https://gitlab.com/qemu-project/qemu/-/jobs/597414772#L4375
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200616154949.6586-1-philmd@redhat.com>
Message-Id: <20200624140446.15380-2-alex.bennee@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Waiting on a process for which we have a pipe will stall if the process
outputs more data than fits into the OS-provided buffer. We must use
communicate() before wait(), and in fact, communicate() perfectly
replaces wait() already.
We have to drop the stderr=subprocess.STDOUT parameter from
subprocess.Popen() in qemu_nbd_early_pipe(), because stderr is passed on
to the child process, so if we do not drop this parameter, communicate()
will hang (because the pipe is not closed).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200630083711.40567-1-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
820c6bee53 added testing of qcow2.py into 291, and it breaks 291
with external data file. Actually, 291 is bad place for qcow2.py
testing, better add a separate test.
For now, drop qcow2.py testing from 291 to fix the regression.
Fixes: 820c6bee53
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200618154052.8629-1-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Commit 96927c744 replaced qdev_init_nofail() call by
isa_realize_and_unref() which has a different error
message. Update the test output accordingly.
Gitlab CI error after merging b77b5b3dc7:
https://gitlab.com/qemu-project/qemu/-/jobs/597414772#L4375
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200616154949.6586-1-philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qdev_prop_set_drive() screws up when the property already has a
non-null value: it neglects to release the old value. Both the old
and the new backend become attached to the same device.
Example (taken from iotest 172): -fda ... -drive if=none,... -global
floppy.drive=none0.
Special case: attempting to use the same backend both times fails.
Example (also from iotest 172): -fda ... -global floppy.drive=floppy0.
Yet another example: -device with multiple drive=... (but not
device_add, which silently drops all but the last duplicate property).
Perhaps drive property override could be made to work. Perhaps it
should. I can't afford the time to figure this out now. What I can
do is reject usage that leaves backends in unhealthy states. For what
it's worth, we've long done the same for netdev properties.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-12-armbru@redhat.com>
Deprecate
-global isa-fdc.driveA=...
-global isa-fdc.driveB=...
in favour of
-device floppy,unit=0,drive=...
-device floppy,unit=1,drive=...
Same for the other floppy controller devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200622094227.1271650-7-armbru@redhat.com>
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-5-armbru@redhat.com>
Use of -global to set a default backend for non-singleton devices is a
bad idea. But as long as we permit it, we better test it.
Test output demonstrates we screw up when -global floppy clashes with
-fda or with -device floppy: according to "info qtree", only the
latter backend is attached, but according to "info block", both are.
Here's the clash with -device:
Testing: -drive if=none,file=TEST_DIR/t.qcow2 -drive if=none,file=TEST_DIR/t.qcow2.2 -global floppy.drive=none0 -device floppy,drive=none1,unit=0
dev: isa-fdc, id ""
[...]
driveA = ""
driveB = ""
[...]
bus: floppy-bus.0
type floppy-bus
dev: floppy, id ""
unit = 0 (0x0)
---> drive = "none1"
[...]
none0 (NODE_NAME): TEST_DIR/t.qcow2 (qcow2)
---> Attached to: /machine/peripheral-anon/device[0]
Cache mode: writeback
none1 (NODE_NAME): TEST_DIR/t.qcow2.2 (qcow2)
---> Attached to: /machine/peripheral-anon/device[0]
Removable device: not locked, tray closed
Cache mode: writeback
/machine/peripheral-anon/device[0] is the floppy created with -device.
Test output further demonstrates the "Drive 'FOO' is already in use
because it has been automatically connected to another device" error
message can be misleading. With '-fda "" -global
floppy.drive=floppy0', it's in use because -global reuses -fda's
backend. There is no other device involved.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-4-armbru@redhat.com>
The additional output demonstrates we screw up when -global isa-fdc
clashes with -drive if=floppy or its sugared forms: according to "info
qtree", only the latter backend is attached, but according to "info
block", both are. For instance:
Testing: -fda TEST_DIR/t.qcow2 -drive if=none,file=TEST_DIR/t.qcow2.2 -global isa-fdc.driveA=none0
dev: isa-fdc, id ""
[...]
driveA = ""
driveB = ""
[...]
bus: floppy-bus.0
type floppy-bus
dev: floppy, id ""
unit = 0 (0x0)
---> drive = "floppy0"
[...]
floppy0 (NODE_NAME): TEST_DIR/t.qcow2 (qcow2)
---> Attached to: /machine/unattached/device[15]
Removable device: not locked, tray closed
Cache mode: writeback
none0 (NODE_NAME): TEST_DIR/t.qcow2.2 (qcow2)
---> Attached to: /machine/unattached/device[14]
Cache mode: writeback
/machine/unattached/device[15] is floppy, and
/machine/unattached/device[14] is isa-fdc.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-2-armbru@redhat.com>
The file qcow2.py was originally contributed in 2012 by Kevin Wolf,
but was not given traditional boilerplate headers at the time. The
missing license was just rectified (commit 16306a7b39) using the
project-default GPLv2+, but as Vladimir is not at Red Hat, he did not
add a Copyright line. All earlier contributions have come from CC'd
authors, where all but Stefan used a Red Hat address at the time of
the contribution, and that copyright carries over to the split to
qcow2_format.py (d5262c7124).
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Philippe Mathieu-Daudé <philmd@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200609205944.3549240-1-eblake@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes: 5d72c68b49
Fixes: cf2d1203dc
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200617104822.27525-6-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes: d89ac3cf30
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200617104822.27525-5-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes: e4d7019e1a
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200617104822.27525-4-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qed does not support shrinking images, so the test_small_target method
should be skipped to keep 041 passing.
Fixes: 16cea4ee1c
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200617104822.27525-3-mreitz@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sometimes, we want to skip some test methods for certain formats. This
decorator allows that.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200617104822.27525-2-mreitz@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add getter for size32, and use it for blocksize, too.
In its human-readable branch, it reports approximate size in
human-readable units next to the exact byte value, like the getter for
64bit size does.
Adjust the expected test output accordingly.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200528225516.1676602-8-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several block device properties related to blocksize configuration must
be in certain relationship WRT each other: physical block must be no
smaller than logical block; min_io_size, opt_io_size, and
discard_granularity must be a multiple of a logical block.
To ensure these requirements are met, add corresponding consistency
checks to blkconf_blocksizes, adjusting its signature to communicate
possible error to the caller. Also remove the now redundant consistency
checks from the specific devices.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20200528225516.1676602-3-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Ever since commit 36683283 (v2.8), the server code asserts that error
strings sent to the client are well-formed per the protocol by not
exceeding the maximum string length of 4096. At the time the server
first started sending error messages, the assertion could not be
triggered, because messages were completely under our control.
However, over the years, we have added latent scenarios where a client
could trigger the server to attempt an error message that would
include the client's information if it passed other checks first:
- requesting NBD_OPT_INFO/GO on an export name that is not present
(commit 0cfae925 in v2.12 echoes the name)
- requesting NBD_OPT_LIST/SET_META_CONTEXT on an export name that is
not present (commit e7b1948d in v2.12 echoes the name)
At the time, those were still safe because we flagged names larger
than 256 bytes with a different message; but that changed in commit
93676c88 (v4.2) when we raised the name limit to 4096 to match the NBD
string limit. (That commit also failed to change the magic number
4096 in nbd_negotiate_send_rep_err to the just-introduced named
constant.) So with that commit, long client names appended to server
text can now trigger the assertion, and thus be used as a denial of
service attack against a server. As a mitigating factor, if the
server requires TLS, the client cannot trigger the problematic paths
unless it first supplies TLS credentials, and such trusted clients are
less likely to try to intentionally crash the server.
We may later want to further sanitize the user-supplied strings we
place into our error messages, such as scrubbing out control
characters, but that is less important to the CVE fix, so it can be a
later patch to the new nbd_sanitize_name.
Consideration was given to changing the assertion in
nbd_negotiate_send_rep_verr to instead merely log a server error and
truncate the message, to avoid leaving a latent path that could
trigger a future CVE DoS on any new error message. However, this
merely complicates the code for something that is already (correctly)
flagging coding errors, and now that we are aware of the long message
pitfall, we are less likely to introduce such errors in the future,
which would make such error handling dead code.
Reported-by: Xueqiang Wei <xuwei@redhat.com>
CC: qemu-stable@nongnu.org
Fixes: https://bugzilla.redhat.com/1843684 CVE-2020-10761
Fixes: 93676c88d7
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200610163741.3745251-2-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
It is possible, that shutdown on target occurs earlier than migration
finish. In this case we crash in bdrv_release_dirty_bitmap_locked()
on assertion "assert(!bdrv_dirty_bitmap_busy(bitmap));" as we do have
busy bitmap, as bitmap migration is ongoing.
We'll fix bitmap migration to gracefully cancel on early shutdown soon.
Now let's fix iotest 194 to wait migration completion before shutdown.
Note that in this test dest_vm.shutdown() is called implicitly, as vms
used as context-providers, see __exit__() method of QEMUMachine class.
Actually, not waiting migration finish is a wrong thing, but the test
started to crash after commit ae00aa2398
"iotests: 194: test also migration of dirty bitmap", which added dirty
bitmaps here. So, Fixes: tag won't hurt.
Fixes: ae00aa2398
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweak]
Message-Id: <20200604083341.26978-1-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Depending on the granularity of holes and amount of metadata consumed
by a file, the 'disk size:' number of 'qemu-img info' is not reliable.
Adjust our test to use a different set of filters to avoid spurious
failures.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Fixes: cf2d1203dc
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200608195629.3299649-1-eblake@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
[eblake: fix merge conflict]
Signed-off-by: Eric Blake <eblake@redhat.com>
Add class for bitmap extension and dump its fields. Further work is to
dump bitmap directory.
Test new functionality inside 291 iotest.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-14-vsementsov@virtuozzo.com>
[eblake: fix iotest output]
Signed-off-by: Eric Blake <eblake@redhat.com>
Only two fields we can parse by generic code, but that is better than
nothing. Keep further refactoring of variable-length fields for another
day.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-12-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Obviously, for-loop body in dump_extensions should be the dump method
of extension.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-11-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Allow formatter class in structure definition instead of hacking with
'mask'. This will simplify further introduction of new formatters.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-10-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
We are going to introduce more Qcow2 structure types, defined like
QcowHeader. Move generic functionality into base class to be reused for
further structure classes.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-9-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
We are going to move field-parsing to super-class, this will be simpler
with simple string specifiers instead of variables.
For some reason, python doesn't allow the definition of ctypes variable
in the class alongside fields: it would not be available then for use
by the 'for' operator. Don't worry: ctypes will be moved to metaclass
soon.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-8-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Use .format and f-strings instead of old %style. Also, the file uses
both '' and "" quotes, for consistency let's use '', except for cases
when we need '' inside the string (use "" to avoid extra escaping).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-7-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
No need in lists: it's a constant variable.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200606081806.23897-6-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>