In terms of encoding MIPS32R6 MIN.fmt, MAX.fmt, MINA.fmt, MAXA.fmt replaced
MIPS-3D RECIP1, RECIP2, RSQRT1, RSQRT2 instructions.
In R6 all Floating Point instructions are supposed to be IEEE-2008 compliant
i.e. FIR.HAS2008 always 1. However, QEMU softfloat for MIPS has not been
updated yet.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Introduce MIPS32R6 Compact Branch instructions which do not have delay slot -
they have forbidden slot instead. However, current implementation does not
support forbidden slot yet.
Add also BC1EQZ and BC1NEZ instructions.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In R6 the special behaviour for data references is also specified for Kernel
and Supervisor mode. Therefore MIPS_HFLAG_UX is replaced by generic
MIPS_HFLAG_AWRAP indicating enabled 32-bit address wrapping.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Also consider OPC_SPIM instruction as deleted in R6 because it is overlaping
with MIPS32R6 SDBBP.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Use "R6_" prefix in front of all new Multiply / Divide instructions for
easier differentiation between R6 and preR6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The encoding of PREF, CACHE, LLD and SCD instruction changed in MIPS32R6.
Additionally, the hint codes in PREF instruction greater than or
equal to 24 generate Reserved Instruction Exception.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Move DSP and Loongson instruction to *_legacy functions as they have been
removed in R6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
For better code readability and to avoid 'if' statements for all R6 and preR6
instructions whose opcodes are the same - decode_opc_special* functions are
split into functions with _r6 and _legacy suffixes.
*_r6 functions will contain instructions which were introduced in R6.
*_legacy functions will contain instructions which were removed in R6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Creating separate decode functions for special, special2 and special3
instructions to ease adding new R6 instructions and removing legacy
instructions.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The encoding of LL and SC instruction has changed in MIPS32 Release 6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signal Reserved Instruction Exception on instructions that do not exist in R6.
In this commit the following groups of preR6 instructions are marked as deleted:
- Floating Point Paired Single
- Floating Point Compare
- conditional moves / branches on FPU conditions
- branch likelies
- unaligned loads / stores
- traps
- legacy accumulator instructions
- COP1X
- MIPS-3D
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The EBase CP0 register is initialised to 0x80000000, however with KVM
the guest's KSEG0 is at 0x40000000. The incorrect value doesn't get
passed to KVM yet as KVM doesn't implement the EBase register, however
we should set it correctly now so as not to break migration/loadvm to a
future version of QEMU that does support EBase.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid access to the CPUMIPSState structure in the
translator, keep a copy of CP0_Config1 into DisasContext. The whole
register is read-only so it can be copied as a single value.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* remotes/kvm/uq/master:
hw/mips: malta: Don't boot from flash with KVM T&E
MAINTAINERS: Add entry for MIPS KVM
target-mips: Enable KVM support in build system
hw/mips: malta: Add KVM support
hw/mips: In KVM mode, inject IRQ2 (I/O) interrupts via ioctls
target-mips: Call kvm_mips_reset_vcpu() from mips_cpu_reset()
target-mips: kvm: Add main KVM support for MIPS
kvm: Allow arch to set sigmask length
target-mips: get_physical_address: Add KVM awareness
target-mips: get_physical_address: Add defines for segment bases
hw/mips: Add API to convert KVM guest KSEG0 <-> GPA
hw/mips/cputimer: Don't start periodic timer in KVM mode
target-mips: Reset CPU timer consistently
KVM: Fix GSI number space limit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From MIPS documentation (Volume III):
UserLocal Register (CP0 Register 4, Select 2)
Compliance Level: Recommended.
The UserLocal register is a read-write register that is not interpreted by
the hardware and conditionally readable via the RDHWR instruction.
This register only exists if the Config3-ULRI register field is set.
Privileged software may write this register with arbitrary information and
make it accessible to unprivileged software via register 29 (ULR) of the
RDHWR instruction. To do so, bit 29 of the HWREna register must be set to a
1 to enable unprivileged access to the register.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MIPS CPU timer (CP0 Count/Compare registers & QEMU timer) is
reset at machine initialisation, including starting the timeout. Both
registers however are placed before mvp in CPUMIPSState so they will
both be zeroed on reset by the memset in mips_cpu_reset() including soon
after init. This doesn't take into account that the timer may be
running, in which case env->CP0_Count will represent the delta against
the VM clock and the timeout will need updating.
At init time (cpu_mips_clock_init()), lets only create the timer.
Setting Count = 1 and starting the timer (cpu_mips_store_count()) can be
done at reset time from cpu_state_reset(), which is after the memset.
There is also no need to set CP0_Compare = 0 as that is already handled
by the memset.
Note that a reset occurs from mips_cpu_realizefn() which is before the
machine init callback has had a chance to set up the CPU interrupts and
the CPU timer, so env->timer will be NULL. This case is handled
explicitly in cpu_mips_store_count(), treating the timer as disabled
(which will also be the right thing to do when KVM support is added).
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will collect all load and store helpers soon. For now
it is just a replacement for softmmu_exec.h, which this patch
stops including directly, but we also include it where this will
be necessary in order to simplify the next patch.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than include helper.h with N values of GEN_HELPER, include a
secondary file that sets up the macros to include helper.h. This
minimizes the files that must be rebuilt when changing the macros
for file N.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Previous implementation presumed that FPU registers are 64-bit and are
working in 64-bit mode. This change first checks MIPS_HFLAG_F64 and if not
set, it does load/store from the odd numbered register pair.
Patch by Matthew Fortune.
Signed-off-by: Matthew Fortune <matthew.fortune@imgtec.com>
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Most targets were using offsetof(CPUFooState, breakpoints) to determine
how much of CPUFooState to clear on reset. Use the next field after
CPU_COMMON instead, if any, or sizeof(CPUFooState) otherwise.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Description of UFR feature:
Required in MIPS32r5 if floating point is implemented and user-mode FR
switching is supported. The UFR register allows user-mode to clear StatusFR
by executing a CTC1 to UFR with GPR[0] as input, and read StatusFR by
executing a CFC1 to UFR.
helper_ctc1 has been extended with an additional parameter rt to check
requirements for UFR feature.
Definition of mips32r5-generic has been modified to include support for UFR.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
Add CP0_Config5, define rw_bitmask and enable modifications.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
FR bit should be initialized to 1 for MIPS64, under condition that this
bit is writable and that CPU has an FPU unit. It should be initialized to
zero for MIPS32.
This fixes different MIPS32 issues with FPU instructions whose behaviour
defaulted to 64-bit FPU mode.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-pull:
exec: Add both big- and little-endian memory helpers
tcg: Add qemu_ld_st_i32/64
tcg: Add TCGMemOp
configure: Remove CONFIG_QEMU_LDST_OPTIMIZATION
tcg: Add tcg-be-ldst.h
tcg: Add tcg-be-null.h
exec: Delete is_tcg_gen_code and GETRA_EXT
tcg-aarch64: Update to helper_ret_*_mmu routines
tcg: Merge tcg_register_helper into tcg_context_init
tcg: Add tcg-runtime.c helpers to all_helpers
tcg: Put target helper data into an array.
tcg: Remove stray semi-colons from target-*/helper.h
tcg: Move helper registration into tcg_context_init
target-m68k: Rename helpers.h to helper.h
tcg: Use a GHashTable for tcg_find_helper
tcg: Delete tcg_helper_get_name declaration
tcg-hppa: Remove tcg backend
Message-id: 1381440525-6666-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Since this is only read in cpu_copy() and linux-user has a global
cpu_model, drop the field from generic code.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Fix incorrect assumption that DSP and non-DSP versions of the following
instructions have the same encoding:
MULT, MULTU, MADD, MADDU, MSUB, MSUBU, MFHI, MFLO, MTHI, MTLO.
Correct the existing (non-DSP) instructions and add DSP equivalents.
Reference:
MIPS Architecture for Programmers Volume II-B: The microMIPS32
Instruction Set
MIPS Architecture for Programmers Volume IV-e: The MIPS DSP Module for
the microMIPS32 Architecture
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When a branch delay slot contains another branch instruction, the code
generated raises an exception, however since is_branch==1,
handle_delay_slot() doesn't get called immediately. This means
ctx->bstate isn't set to BS_BRANCH, and the decoder continues decoding
until a non-branch instruction is found.
If the first branch was a branch likely instruction then each
instruction after it generates code for the unlikely case, to go to the
next tb starting after the delay slot. This results in multiple goto_tb
tcg ops being generated with the same exit number. When debug is enabled
this hits:
tcg-op.h:2589: tcg_gen_goto_tb: Assertion `(tcg_ctx.goto_tb_issue_mask & (1 << idx)) == 0' failed.
This is fixed by removing is_branch entirely, and calling
handle_delay_slot() if (ctx.hflags & MIPS_HFLAG_BMASK) was set prior to
the current instruction being decoded. This still prevents
handle_delay_slot() being called immediately after a branch but allows
it to still be called after a branch within a delay slot.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Prepares for changing cpu_single_step() argument to CPUState.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Also use bool type while at it.
Prepares for moving singlestep_enabled field to CPUState.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make cpustats monitor command available unconditionally.
Prepares for changing kvm_handle_internal_error() and kvm_cpu_exec()
arguments to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The emulator needs to check in hflags if DSP unit has been turned off before
it generates code for MUL_PH, MUL_S_PH, MULQ_S_W, and MULQ_RS_W.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Both fields are used in VMState, thus need to be moved together.
Explicitly zero them on reset since they were located before
breakpoints.
Pass PowerPCCPU to kvmppc_handle_halt().
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add accumulator arguments to gen_HILO and gen_muldiv, rather than
extracting the accumulator directly from ctx->opcode. The extraction
was only right for the standard encoding: MIPS16 doesn't have access
to the DSP registers, while microMIPS encodes the accumulator register
in a different field (bits 14 and 15).
Passing the accumulator register is probably an over-generalisation
for division and 64-bit multiplication, which never access anything
other than HI and LO, and which always pass 0 as the new argument.
Separating them felt a bit fussy though.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The gen_icount_start/end functions are now somewhat misnamed since they
are useful for generic "start/end of TB" code, used for more than just
icount. Rename them to gen_tb_start/end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
compute_hflags() will reset DSP h-flags, so MX bit should be initially set
for usermode in cpu_state_reset() if DSP ASE is implemented.
This change will bring back user-mode support for DSP ASE, since one of the
recent changes broke it.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Sign-extend the result of LWR, as is already done for LWL. This is necessary
in the case where LWR loads the full word (i.e. the address is actually
aligned). In the other cases, it is implementation defined whether the
upper 32 bits of the result are unchanged or a copy of bit 31. The latter
seems easier to implement.
Previously the code used:
(oldval & (0xfffffffe << (31 - bitshift))) | (newval >> bitshift)
which zeroed the upper bits of the register, losing any previous sign
extension in the unaligned cases.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Make RESTORE use sign-extending rather than zero-extending loads.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
DSP instruction from the (d)append sub-class can be implemented with
TCG. Use a different function for these instructions are they are quite
different from compare-pick sub-class.
Fix BALIGN instruction for negative value, where the value should be
zero-extended before being shift to the right.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On CPU without DSP ASE support, a reserved instruction exception (instead of
a DSP ASE sate disabled) should be generated.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Copy insn_flags in DisasContext to avoid passing a CPUMIPSState pointer
to subroutines, as suggested by Richard Henderson. Change subroutines to
use this new field and remove the first argument.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When rd is 0, which still need to do the actually load to possibly
generate a TLB exception.
Reviewed-by: Eric Johnson <ericj@mips.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Note that target-alpha accesses this field from TCG, now using a
negative offset. Therefore the field is placed last in CPUState.
Pass PowerPCCPU to [kvm]ppc_fixup_cpu() to facilitate this change.
Move common parts of mips cpu_state_reset() to mips_cpu_reset().
Acked-by: Richard Henderson <rth@twiddle.net> (for alpha)
[AF: Rebased onto ppc CPU subclasses and openpic changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The immediate value is 9bits, should sign-extend to 16bits. The return value to
register should sign-extend to target_long, as Richard says, removing an
unnecessary cast works fun.
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
I check MIPS microMIPS manual [1], and found the major opcode might
be wrong. I add a comment to explicitly indicate what manual I am refering
to, and according that manual I remove microMIPS32 major opcodes 0x1f.
As for others, like 0x16, 0x17, 0x36 and 0x37, they are for higher-order
MIPS ISA level or new revision of this microMIPS architecture. Quote
from Johnson, they are belong MIPS64 [2].
[1] http://www.mips.com/products/architectures/micromips/#specifications
MIPS Architecture for Programmers Volume II-B:
The microMIPS32 Instruction Set (Revision 3.05)
MD00582-2B-microMIPS-AFP-03.05.pdf
[2] http://www.mips.com/products/architectures/mips64/
MIPS Architecture For Programmers
Volume II-A: The MIPS64 Instruction Set
MD00087-2B-MIPS64BIS-AFP-03.51.pdf
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Current QEMU MIPS POOL32AXF encoding comes from microMIPS32
and microMIPS32 DSP. Add comment here to help reading.
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While reading microMIPS decoding, I found a possible wrong opcode
encoding. According to [1] page 166, the bits 13..12 for MULTU is
0x01 rather than 0x00. Please review, thanks.
[1] MIPS Architecture for Programmers VolumeIV-e: The MIPS DSP
Application-Specific Extension to the microMIPS32 Architecture
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The call to gen_logic_imm for OPC_LUI passes -1 for rs. This
causes the MIPS_DEBUG statement to seg fault due to the deference
of regnames[rs]. This patch fixes that.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
(aurel32: replaced static string formating by a static string)
Pass around CPUArchState instead of using global cpu_single_env.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Use the deposit op instead of and hardcoded bit field insertion. It
allows the host to emit the corresponding instruction if available.
At the same time remove the (lsb > msb) test. The MIPS64R2 instruction
set manual says "Because of the instruction format, lsb can never be
greater than msb, so there is no UNPREDICATABLE case for this
instruction."
(Bug reported as LP:1071149.)
Cc: Никита Канунников <n.kanunnikov@sbtcom.ru>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The result of a division by 0, or a division of INT_MIN by -1 in the
signed case, is unpredictable. Just replace 0 by 1 in that case so that
it doesn't trigger a floating point exception on the host.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Avoid the branches in movn/movz implementation and replace them with
movcond. Also update a wrong command.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Store conditional operations only need local temps in user mode. Fix
the code to use temp local only in user mode, this spares two memory
stores in system mode.
At the same time remove a wrong a wrong copied & pasted comment,
store operations don't have a register destination.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Load/store from helpers should be avoided as they are quite
inefficient. Rewrite unaligned loads instructions using TCG and
aligned loads. The number of actual loads operations to implement
an unaligned load instruction is reduced from up to 8 to 1.
Note: As we can't rely on shift by 32 or 64 undefined behaviour,
the code loads already shift by one constants.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Load/store operations use macros for historical reasons. Now that there
is no point in keeping them, replace them by direct calls to qemu_ld/st.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the new softfloat floatXX_muladd() functions to implement the madd,
msub, nmadd and nmsub instructions. At the same time replace the name of
the helpers by the name of the instruction, as the only reason for the
previous names was to keep the macros simple.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the CPU state after a possible retranslation is going to be handled
through code retranslation, we don't need to save the CPU state before.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the CPU state is restored through retranslation after an exception,
btarget should also be restored.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
All switch() decoding instruction have a default entry, so it is possible
to have unused enum entries. Remove conditional definitions of MIPS64
opcode enums, as it only makes the code less readable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With normal FP, this doesn't have much affect on the generated code,
because most of the FP operations are not CONST/PURE, and so we spill
registers in about the same frequency as the explicit load/stores.
But with Loongson multimedia instructions, which are all integral and
whose helpers are in fact CONST+PURE, this greatly improves the code.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For all targets that currently call tcg_gen_debug_insn_start,
add CPU_LOG_TB_OP_OPT to the condition that gates it.
This is useful for comparing optimization dumps, when the
pre-optimization dump is merely noise.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implements all of the COP2 instructions except for the S<cond>
family of comparisons. The documentation is unclear for those.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
this will prevent some of the compilation errors with debugging
enabled from creeping back in.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The macro uses the DisasContext. Pass it around as needed.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Used by MIPS_DEBUG, when enabled.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add an explicit CPUState parameter instead of relying on AREG0
and switch to AREG0 free mode.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
This change updates the CPU reset sequence to use a common piece of code
that figures out CPU state flags, fixing the problem with MIPS_HFLAG_COP1X
not being set where applicable that causes floating-point MADD family
instructions (and other instructions from the MIPS IV FP subset) to trap.
As compute_hflags is now shared between op_helper.c and translate.c, the
function is now moved to a common header. There are no changes to this
function.
The problem was seen with the 24Kf MIPS32r2 processor in user emulation.
The new approach prevents system and user emulation from diverging -- all
the hflags state is initialized in one place now.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The microMIPS SWP and SDP instructions do not modify GPRs. So their
behavior is well defined when RD equals BASE. The MIPS Architecture
Verification Programs (AVPs) check that they work as expected. This
is required for AVPs to pass.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MIPS Architecture Verification Programs (AVPs) check privileged
instructions for the required privilege level. These changes are needed
to pass the AVP suite.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The kernel will emulate this instruction if it's not supported
natively. This insn is used for TLS, among other things, and
so is required by modern glibc.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The FS input to CVT.PS.S is the high half and FT is the low half.
tcg_gen_concat_i32_i64 takes the low half first, so the operands
were in the wrong order.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Read the second input operand of RECIP2.S and RECIP2.PS from FT rather
than FD. RECIP2.D is already correct.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While running in the usermode emulator all of the required*
MIPS32r2 RDHWR hardware registers should be accessible (the
Linux kernel enables access to these same registers). Note
that these registers are still enabled when the MIPS ISA is
not release 2. This is OK since the Linux kernel emulates
access to them when they are not available in hardware.
* There is also the ULR register which is only recommended
for full release 2 compliance. Incidentally, accessing
this register in the current implementation works fine
without flipping its access bit.
Signed-off-by: Meador Inge <meadori@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change addresses a problem where QEMU incorrectly traps on
floating-point MADD group instructions with SIGILL, at least while
emulating MIPS32r2 processors. These instructions use the COP1X major
opcode and include ones like:
madd.d $f2,$f4,$f2,$f6
Here's Nathan's original analysis of the problem:
"QEMU essentially does:
d = find_cpu (cpu_string) // get CPU definition
fpu_init (env, d) // initialize fpu state (init FCR0, basically)
cpu_reset (env)
...and the cpu_reset call clears all interesting state that fpu_init
setup, then proceeds to reinitialize all the CP0 registers...but not
FCR0."
I have verified this change with system emulation running the GDB test
suite for the mips-sde-elf target (o32, big endian, 24Kf CPU emulated),
there were 55 progressions and no regressions.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 0f71a7095d (target-mips: QOM'ify
CPU) hooked up cpu_state_reset() to CPUClass::reset(). Dropping the
introduction of subclasses for 1.1, due to mips_def_t the reset code
could not be QOM'ified yet, i.e. cpu_state_reset() will not forward to
CPUClass::reset().
Update cpu_mips_init() with cpu_reset() nontheless, indirectly calling
cpu_state_reset(), so that generic code can be converted to call
cpu_reset().
Signed-off-by: Andreas Färber <afaerber@suse.de>
There's some dodgy application of De Morgan's law in the emulation
of the MIPS BC1ANY[24]F instructions: they end up branching only
if all CCs are false, rather than if one CC is.
Tested on mips64-linux-gnu, where it fixes the GCC MIPS3D tests.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move code not dependent on mips_def_t from cpu_mips_init() into a
QOM initfn, as a start.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Embed CPUMIPSState as first member of QOM MIPSCPU.
Let CPUClass::reset() call cpu_state_reset() for now.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Scripted conversion:
sed -i "s/CPUState/CPUMIPSState/g" target-mips/*.[hc]
sed -i "s/#define CPUMIPSState/#define CPUState/" target-mips/cpu.h
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Frees the identifier cpu_reset for QOM CPUs (manual rename).
Don't hide the parameter type behind explicit casts, use static
functions with strongly typed argument to indirect.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Function gen_pc_load was introduced in commit
d2856f1ad4.
The only reason for parameter searched_pc was
a debug statement in target-i386/translate.c.
Parameter puc was needed by target-sparc until
commit d7da2a1040.
Remove searched_pc from the debug statement and remove both
parameters from the parameter list of gen_pc_load.
As the function name gen_pc_load was also misleading,
it is now called restore_state_to_opc. This new name
was suggested by Peter Maydell, thanks.
v2: Remove last parameter, too, and rename the function.
v3: Fix [] typo in target-arm/translate.c.
Fix wrong SHA1 object name in commit message (copy+paste error).
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
tcg_gen_exit_tb takes a parameter of type tcg_target_long,
so the type casts of pointer to long should be replaced by
type casts of pointer to tcg_target_long (suggested by Blue Swirl).
These changes are needed for build environments where
sizeof(long) != sizeof(void *), especially for w64.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The rule is:
- don't save PC if the exception is only triggered by softmmu.
- save PC if the exception can be triggered by an helper.
Fix a 64-bit kernel crash when loading modules.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Break the TB after reading the count register. This makes it
possible to take timer interrupts immediately after a read of
a possibly expired timer.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
The translation of dmt/emt/dvpe/evpe was doing the moral equivalent of:
int x;
... /* no initialization of x */
x = f (x);
which confused later bits of TCG rather badly, leading to crashes.
Fix the helpers to only return results (those instructions have no
inputs), and fix the translation code accordingly.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
fprintf_function uses format checking with GCC_FMT_ATTR.
Format errors were fixed in
* target-i386/helper.c
* target-mips/translate.c
* target-ppc/translate.c
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compiling with GCC 4.6.0 20100925 produced a lot of warnings like:
/src/qemu/target-mips/translate.c: In function 'gen_ld':
/src/qemu/target-mips/translate.c:1039:17: error: variable 'opn' set but not used [-Werror=unused-but-set-variable]
Fix by adding a dummy cast so that the variable is not unused.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 36388314fe moved most of the
interrupt logic to cpu-exec.c. Remove the remaining useless code
and fix software interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Edgar E. Iglesias <edgar@axis.com>
Tested-by: Edgar E. Iglesias <edgar@axis.com>
This patch adds support for loongson 2E & 2F instructions. They are the
same instructions, but differ by the opcode encoding.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add instruction decoding for the microMIPS ASE. All we do is decode and
then forward to the existing gen_* routines.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Change code handling mips16-specific branches to use ISA-neutral special
opcodes. Since there are several places where the delay slot
requirements for microMIPS branches differ from mips16 branches, using
opcodes is easier than checking hflags, then checking mips16
vs. microMIPS.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move all knowledge about coprocessor-checking and register numbering
into the gen_cmp* helper functions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add FMT_* constants for the floating-point format field in opcodes and
tweak a few places to use them. Add enums for various invocations of
FOP and tweak gen_farith and its lone caller accordingly.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In the previous patch which introduced fprintf_function to
allow parameter checking by gcc some compiler warnings
remained unfixed.
These warnings are fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When we signal a CpU exception for coprocessor 0, we should indicate
that it's for coprocessor 0 instead of coprocessor 1.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
