This relatively small architectural feature adds the following:
FIR.FREP: Read-only. If FREP=1, then Config5.FRE and Config5.UFE are
available.
Config5.FRE: When enabled all single-precision FP arithmetic instructions,
LWC1/LWXC1/MTC1, SWC1/SWXC1/MFC1 cause a Reserved Instructions
exception.
Config5.UFE: Allows user to write/read Config5.FRE using CTC1/CFC1
instructions.
Enable the feature in MIPS64R6-generic CPU.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Save MSACSR state. Also remove fp_status, msa_fp_status, hflags and restore
them in post_load() from the architectural registers.
Float exception flags are not present in vmstate. Information they carry
is used only by softfloat caller who translates them into MIPS FCSR.Cause,
FCSR.Flags and then they are cleared. Therefore there is no need for saving
them in vmstate.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Enable vectored interrupt support for the 74Kf CPU, reflecting hardware.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the M14K and M14Kc processors from MIPS Technologies that are the
original implementation of the microMIPS ISA. They are dual instruction
set processors, implementing both the microMIPS and the standard MIPSr32
ISA.
These processors correspond to the M4K and 4KEc CPUs respectively,
except with support for the microMIPS instruction set added, support for
the MCU ASE added and two extra interrupt lines, making a total of 8
hardware interrupts plus 2 software interrupts. The remaining parts of
the microarchitecture, in particular the pipeline, stayed unchanged.
The presence of the microMIPS ASE is is reflected in the configuration
added. We currently have no support for the MCU ASE, including in
particular the ACLR, ASET and IRET instructions in either encoding, and
we have no support for the extra interrupt lines, including bits in
CP0.Status and CP0.Cause registers, so these features are not marked,
making our support diverge from real hardware.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the 5KEc and 5KEf processors from MIPS Technologies that are the
original implementation of the MIPS64r2 ISA.
Silicon for these processors has never been taped out and no soft cores
were released even. They do exist though, a CP0.PRId value has been
assigned and experimental RTLs produced at the time the MIPS64r2 ISA has
been finalized. The settings introduced here faithfully reproduce that
hardware.
As far the implementation goes these processors are the same as the 5Kc
and the 5Kf CPUs respectively, except implementing the MIPS64r2 rather
than the original MIPS64 instruction set. There must have been some
updates to the CP0 architecture as mandated by the ISA, such as the
addition of the EBase register, although I am not sure about the exact
details, no documentation has ever been produced for these processors.
The remaining parts of the microarchitecture, in particular the
pipeline, stayed unchanged. Or to put it another way, the difference
between a 5K and a 5KE CPU corresponds to one between a 4K and a 4KE
CPU, except for the 64-bit rather than 32-bit ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Set the CP0.Config3.DSP2P bit for the 74kf processor and both that bit
and the CP0.Config3.DSP bit for the artificial mips32r5-generic and
mips64dspr2 processors. They have the DSPr2 ASE enabled in `insn_flags'
and CPUs that implement that ASE need to have both CP0.Config3.DSP and
CP0.Config3.DSP2P set or software won't detect its presence.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: remove DSP flags from mips32r5-generic]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA support to mips32r5-generic core definition
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add msa_reset() and global msa register (d type only)
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
For Standard TLB configuration (Config.MT=1):
TLBINV invalidates a set of TLB entries based on ASID. The virtual address is
ignored in the entry match. TLB entries which have their G bit set to 1 are not
modified.
TLBINVF causes all entries to be invalidated.
Single TLB entry can be marked as invalid on TLB entry write by having
EntryHi.EHINV set to 1.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
PageGrain needs rw bitmask which differs between MIPS architectures.
In pre-R6 if RIXI is supported, PageGrain.XIE and PageGrain.RIE are writeable,
whereas in R6 they are read-only 1.
On MIPS64 mtc0 instruction left shifts bits 31:30 for MIPS32 backward
compatiblity, therefore there are separate mtc0 and dmtc0 helpers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Add U suffix to various places where we shift a 1 left by 31,
to avoid undefined behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Description of UFR feature:
Required in MIPS32r5 if floating point is implemented and user-mode FR
switching is supported. The UFR register allows user-mode to clear StatusFR
by executing a CTC1 to UFR with GPR[0] as input, and read StatusFR by
executing a CFC1 to UFR.
helper_ctc1 has been extended with an additional parameter rt to check
requirements for UFR feature.
Definition of mips32r5-generic has been modified to include support for UFR.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
Add CP0_Config5, define rw_bitmask and enable modifications.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
Add mips32r5-generic among CPU definitions for MIPS.
Define ISA_MIPS32R3 and ISA_MIPS32R5.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Eric Johnson <eric.johnson@imgtec.com>
34Kf core does support DSP ASE.
CP0_Config3 configuration for 34Kf and description are wrong.
Please refer to MIPS32(R) 34Kf(TM) Processor Core Datasheet
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
fprintf_function uses format checking with GCC_FMT_ATTR.
Format errors were fixed in
* target-i386/helper.c
* target-mips/translate.c
* target-ppc/translate.c
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix regression introduced by d19954f46d.
4Kc and 4KEc don't support MIPS16.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
4Kc, 4KEc cores do not support MIPS16, so not only the
CP0_Config1 had to be fixed (see previous patch),
but also MIPS16 instructions must not be executed.
(Hint from Nathan Froyd, thanks).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Running programs with the MIPS user-mode emulator fails during dynamic
loading, as floating-point instructions are not enabled in in
env->hflags. Move the code for doing so from fpu_init to cpu_reset so
the MIPS_HFLAG_{FPU,F64} setting doesn't get clobbered by cpu_reset
setting env->hflags to MIPS_HFLAG_UM.
The same end can be achieved by swapping the ordering of fpu_init and
cpu_reset in cpu_mips_init, but it seemed better to consolidate the
CONFIG_USER_ONLY code into a single location.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Depending on the CPU, CP0_LLAddr is either read-only or read-write,
and the returned value can be shifted by a variable amount of bits.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Remove cpu_mips_register()
- move mmu_init(), fpu_init() and mvp_init() into cpu_mips_init()
- move the other parts in cpu_mips_init()
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Replace runtime checks on env->user_mode_only by compile time
checks on CONFIG_USER_ONLY.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6276 c046a42c-6fe2-441c-8c8c-71466251a162
The attached patch updates the FSF address in the GPL/LGPL boilerplate
in most GPL/LGPLed files, and also in COPYING.LIB.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6162 c046a42c-6fe2-441c-8c8c-71466251a162
Change from v1:
Avoid changing the existing coding style in certain files.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6120 c046a42c-6fe2-441c-8c8c-71466251a162
Attached patch fixes a warning in cpu_mips_find_by_name().
'name' is a string, so it should be declared as char*, not unsigned char*.
(Hervé Poussineau)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5213 c046a42c-6fe2-441c-8c8c-71466251a162
