Make CP0.Status writes made with the MTTC0 instruction respect this
register's mask just like all the other places. Also preserve the
current values of masked out bits.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Rewrite the FPU register access parts of `mips_cpu_gdb_read_register'
and `mips_cpu_gdb_write_register' for consistency between each other.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make sure the address space is unconditionally wrapped on 32-bit
processors, that is ones that do not implement at least the MIPS III
ISA.
Also make MIPS16 SAVE and RESTORE instructions use address calculation
rather than plain arithmetic operations for stack pointer manipulation
so that their semantics for stack accesses follows the architecture
specification. That in particular applies to user software run on
64-bit processors with the CP0.Status.UX bit clear where the address
space is wrapped to 32 bits.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Tighten ISA level checks down to MIPS II that many of our instructions
are missing. Also make sure any 64-bit instruction enables are only
applied to 64-bit processors, that is ones that implement at least the
MIPS III ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix CP0.Config3.ISAOnExc write accesses on microMIPS processors. This
bit is mandatory for any processor that implements the microMIPS
instruction set. This bit is r/w for processors that implement both the
standard MIPS and the microMIPS instruction set. This bit is r/o and
hardwired to 1 if only the microMIPS instruction set is implemented.
There is no other bit ever writable in CP0.Config3 so defining a
corresponding `CP0_Config3_rw_bitmask' member in `CPUMIPSState' is I
think an overkill. Therefore make the ability to write the bit rely on
the presence of ASE_MICROMIPS set in the instruction flags.
The read-only case of the microMIPS instruction set being implemented
only can be added when we add support for such a configuration. We do
not currently have such support, we have no instruction flag that would
control the presence of the standard MIPS instruction set nor any
associated code in instruction decoding.
This change is needed to boot a microMIPS Linux kernel successfully,
otherwise it hangs early on as interrupts are enabled and then the
exception handler invoked loops as its first instruction is interpreted
in the wrong execution mode and triggers another exception right away.
And then over and over again.
We already check the current setting of the CP0.Config3.ISAOnExc in
`set_hflags_for_handler' to set the ISA bit correctly on the exception
handler entry so it is the ability to set it that is missing only.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Include CP0.Config2 through CP0.Config5 registers in the register dump
produced with the `info registers' monitor command. Align vertically
with the registers already output.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix microMIPS MOVE16 and MOVEP instructions on 64-bit processors by
using register addition operations.
This copies the approach taken with MIPS16 MOVE instructions (I8_MOV32R
and I8_MOVR32 opcodes) and follows the observation that OPC_ADDU expands
to tcg_gen_mov_tl whenever `rt' is 0 and `rs' is not, therefore copying
`rs' to `rd' verbatim. This is not the case with OPC_ADDIU where a
sign-extension from bit #31 is made, unless in the uninteresting case of
`rs' being 0, losing the upper 32 bits of the value copied for any
proper 64-bit values.
This also serves as an optimization as one op is produced in generated
code rather than two (again, unless `rs' is 0, where it doesn't change
anything).
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make writes to CP0.Status and CP0.Cause have the same effect as
executing corresponding MTC0 instructions would in Kernel Mode. Also
ignore writes in the user emulation mode.
Currently for requests from the GDB stub we write all the bits across
both registers, ignoring any read-only locations, and do not synchronise
the environment to evaluate side effects. We also write these registers
in the user emulation mode even though a real kernel presents them as
read only.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct these issues with the handling of CP0.Status for MIPSr6:
* only ignore the bit pattern of 0b11 on writes to CP0.Status.KSU, that
is for processors that do implement Supervisor Mode, let the bit
pattern be written to CP0.Status.UM:R0 freely (of course the value
written to read-only CP0.Status.R0 will be discarded anyway); this is
in accordance to the relevant architecture specification[1],
* check the newly written pattern rather than the current contents of
CP0.Status for the KSU bits being 0b11,
* use meaningful macro names to refer to CP0.Status bits rather than
magic numbers.
References:
[1] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
Privileged Resource Architecture", MIPS Technologies, Inc., Document
Number: MD00091, Revision 6.00, March 31, 2014, Table 9.45 "Status
Register Field Descriptions", pp. 210-211.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct MIPS16/microMIPS branch size calculation in PC adjustment
needed:
- to set the value of CP0.ErrorEPC at the entry to the reset exception,
- for the purpose of branch reexecution in the context of device I/O.
Follow the approach taken in `exception_resume_pc' for ordinary, Debug
and NMI exceptions.
MIPS16 and microMIPS branches can be 2 or 4 bytes in size and that has
to be reflected in calculation. Original MIPS ISA branches, which is
where this code originates from, are always 4 bytes long, just as all
original MIPS ISA instructions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Restore the order of helpers that used to be: unary operations (generic,
then MIPS-specific), binary operations (generic, then MIPS-specific),
compare operations. At one point FMA operations were inserted at a
random place in the file, disregarding the preexisting order, and later
on even more operations sprinkled across the file. Revert the mess by
moving FMA operations to a new ternary class inserted after the binary
class and move the misplaced unary and binary operations to where they
belong.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Remove the `FLOAT_OP' macro, unused since commit
b6d96beda3 [Use temporary registers for
the MIPS FPU emulation.].
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Move the call to `update_fcr31' in `helper_float_cvtw_s' after the
exception flag check, for consistency with the remaining helpers that do
it last too.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Enable vectored interrupt support for the 74Kf CPU, reflecting hardware.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the M14K and M14Kc processors from MIPS Technologies that are the
original implementation of the microMIPS ISA. They are dual instruction
set processors, implementing both the microMIPS and the standard MIPSr32
ISA.
These processors correspond to the M4K and 4KEc CPUs respectively,
except with support for the microMIPS instruction set added, support for
the MCU ASE added and two extra interrupt lines, making a total of 8
hardware interrupts plus 2 software interrupts. The remaining parts of
the microarchitecture, in particular the pipeline, stayed unchanged.
The presence of the microMIPS ASE is is reflected in the configuration
added. We currently have no support for the MCU ASE, including in
particular the ACLR, ASET and IRET instructions in either encoding, and
we have no support for the extra interrupt lines, including bits in
CP0.Status and CP0.Cause registers, so these features are not marked,
making our support diverge from real hardware.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make the data type used for the CP0.Config4 and CP0.Config5 registers
and their mask signed, for consistency with the remaining 32-bit CP0
registers, like CP0.Config0, etc.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the 5KEc and 5KEf processors from MIPS Technologies that are the
original implementation of the MIPS64r2 ISA.
Silicon for these processors has never been taped out and no soft cores
were released even. They do exist though, a CP0.PRId value has been
assigned and experimental RTLs produced at the time the MIPS64r2 ISA has
been finalized. The settings introduced here faithfully reproduce that
hardware.
As far the implementation goes these processors are the same as the 5Kc
and the 5Kf CPUs respectively, except implementing the MIPS64r2 rather
than the original MIPS64 instruction set. There must have been some
updates to the CP0 architecture as mandated by the ISA, such as the
addition of the EBase register, although I am not sure about the exact
details, no documentation has ever been produced for these processors.
The remaining parts of the microarchitecture, in particular the
pipeline, stayed unchanged. Or to put it another way, the difference
between a 5K and a 5KE CPU corresponds to one between a 4K and a 4KE
CPU, except for the 64-bit rather than 32-bit ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
CP1.FIR is read-only in hardware so gdbstub must respect it. We already
respect it for CTC1 instructions, so do it here too.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix an off-by-one error in `mips_cpu_gdb_write_register' for register
matching how `mips_cpu_gdb_read_register' handles it. This register
slot is a fake anyway, there's nothing in hardware that corresponds to
it.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Avoid to allocate different TCG registers for the FPU registers
that are mapped on the MSA vectore registers.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct the way PC is updated when single-stepping instructions, by
keeping the old PC only for the BS_EXCP (exception condition) state.
Some MTC0 (and possibly other) instructions switch to the BS_STOP state
to terminate the current translation block, so that the state transition
of the simulated CPU resulting from the CP0 operation takes effect with
the following instruction. This happens with `mtc0 <reg>,c0_config' for
example, typically used to set KSEG0 cacheability.
While single-stepping this has a side-effect of not advancing the PC
past the instruction just executed; subsequent single-step traps will
stop at the same instruction repeatedly. Example:
(gdb) stepi
0x80004d24 in _start ()
5: x/i $pc
=> 0x80004d24 <_start+364>: mfc0 t1,c0_config
(gdb)
0x80004d28 in _start ()
5: x/i $pc
=> 0x80004d28 <_start+368>: li at,-8
(gdb)
0x80004d2c in _start ()
5: x/i $pc
=> 0x80004d2c <_start+372>: and t1,t1,at
(gdb)
0x80004d30 in _start ()
5: x/i $pc
=> 0x80004d30 <_start+376>: ori t1,t1,0x3
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
-- oops!
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
New R6 COP1 conditional branches currently don't have delay slot. Fixing this
by setting MIPS_HFLAG_BDS32 flag which is required for branches having 4-byte
delay slot.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Set the CP0.Config3.DSP2P bit for the 74kf processor and both that bit
and the CP0.Config3.DSP bit for the artificial mips32r5-generic and
mips64dspr2 processors. They have the DSPr2 ASE enabled in `insn_flags'
and CPUs that implement that ASE need to have both CP0.Config3.DSP and
CP0.Config3.DSP2P set or software won't detect its presence.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: remove DSP flags from mips32r5-generic]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Define macros for CP0.Config3 and CP0.Config4 bits. These used to be
exhaustive as at MIPS32r3, but more bits may have been added since.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make microMIPS FP branches respect CP0.Status.CU1 and trap with a
Coprocessor Unusable exception if COP1 has been disabled; also trap if
no FPU is present at all.
Standard MIPS FP instruction encodings have a more regular structure and
branches are covered with a single umbrella along other instructions.
This is not the case with the microMIPS encoding, this case has to be
taken care of explicitly here. Code to do so has been copied from the
standard MIPS code handler for OPC_CP1, in `decode_opc'.
Problems arising from this bug will generally only show up on user
context switches in operating systems making use of lazy FP context
switches, such as Linux. It will also more readily trigger if software
FPU emulation is used, either implicitly on a non-float CPU, or forced
on a hard-float CPU such as with the "nofpu" Linux kernel command line
argument.
The problem may have been easily missed because we have no hard-float
microMIPS CPU configuration present; in fact we have no microMIPS CPU
configuration of any kind present.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA support to mips32r5-generic core definition
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA MI10 format instructions
update LSA and DLSA for MSA
add 16, 64 bit load and store
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA BIT format instructions
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA I5 format instructions
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA I8 format instructions
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add msa_helper.c
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add msa_reset() and global msa register (d type only)
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA opcode enum
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
stop translation as ctc1 instruction can change hflags
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Remove the duplicated ieee_rm in gdbstub.c.
Make the other ieee_rm and ieee_ex_to_mips available to other files.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA exceptions
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add defines and data structure for MIPS SIMD Architecture
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Release 6 limits the number of cases where software can cause UNDEFINED or
UNPREDICTABLE behaviour. In this case, when accessing reserved / unimplemented
CP0 register, writes are ignored and reads return 0.
In pre-R6 the behaviour is not specified, but generating RI exception is not
what the real HW does.
Additionally, remove CP0 Random register as it became reserved in Release 6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
In Release 6 not all the values are allowed to be written to a register.
If the value is not valid or unsupported then it should stay unchanged.
For pre-R6 the existing behaviour has been changed only for CP0_Index register
as the current implementation does not seem to be correct - it looks like it
tries to limit the input value but the limit is higher than the actual
number of tlb entries.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>