Drop WIN_SRST, it has the same value as WIN_DEVICE_RESET.
Drop unused WIN_RESTORE, it has the same value as WIN_RECAL.
Drop codes that are not implemented and long obsolete: WIN_READ_LONG,
WIN_READ_LONG_ONCE, WIN_WRITE_LONG, WIN_WRITE_LONG_ONCE, WIN_FORMAT
(all obsolete since ATA4), WIN_ACKMEDIACHANGE, WIN_POSTBOOT,
WIN_PREBOOT (obsolete since ATA3), WIN_WRITE_SAME (obsolete since
ATA3, code reused for something else in ACS2), WIN_IDENTIFY_DMA
(obsolete since ATA4).
Drop codes that are not implemented and vendor-specific:
EXABYTE_ENABLE_NEST, DISABLE_SEAGATE.
Drop WIN_INIT, it isn't implemented, its value used to be reserved,
and is used for something else since ATA8.
CFA_IDLEIMMEDIATE isn't specific to CFATA. ACS-2 shows it as a
defined command in ATA-1, -2 and -3. Rename to WIN_IDLEIMMEDIATE2.
Mark vendor specific, retired, and obsolete codes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Multiplexing callbacks complicates matters needlessly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For now, this just protects against programming errors like having the
same drive back multiple non-qdev devices, or untimely bdrv_delete().
Later commits will add other interesting uses.
While there, rename BlockDriverState member peer to dev, bdrv_attach()
to bdrv_attach_dev(), bdrv_detach() to bdrv_detach_dev(), and
bdrv_get_attached() to bdrv_get_attached_dev().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Most changes were made using these commands:
git grep -la '__attribute__((packed))'|xargs perl -pi -e 's/__attribute__\(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((packed))'|xargs perl -pi -e 's/__attribute__ \(\(packed\)\)/QEMU_PACKED/'
git grep -la '__attribute__((__packed__))'|xargs perl -pi -e 's/__attribute__\(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute__ ((__packed__))'|xargs perl -pi -e 's/__attribute__ \(\(__packed__\)\)/QEMU_PACKED/'
git grep -la '__attribute((packed))'|xargs perl -pi -e 's/__attribute\(\(packed\)\)/QEMU_PACKED/'
Whitespace in linux-user/syscall_defs.h was fixed manually
to avoid warnings from scripts/checkpatch.pl.
Manual changes were also applied to hw/pc.c.
I did not fix indentation with tabs in block/vvfat.c.
The patch will show 4 errors with scripts/checkpatch.pl.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Decouple the I/O accounting from bdrv_aio_readv/writev/flush and
make the hardware models call directly into the accounting helpers.
This means:
- we do not count internal requests from image formats in addition
to guest originating I/O
- we do not double count I/O ops if the device model handles it
chunk wise
- we only account I/O once it actuall is done
- can extent I/O accounting to synchronous or coroutine I/O easily
- implement I/O latency tracking easily (see the next patch)
I've conveted the existing device model callers to the new model,
device models that are using synchronous I/O and weren't accounted
before haven't been updated yet. Also scsi hasn't been converted
to the end-to-end accounting as I want to defer that after the pending
scsi layer overhaul.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The unplug protocol is necessary to support PV drivers in the guest: the
drivers expect to be able to "unplug" emulated disks and nics before
initializing the Xen PV interfaces.
It is responsibility of the guest to make sure that the unplug is done
before the emulated devices or the PV interface start to be used.
We use pci_for_each_device to walk the PCI bus, identify the devices and
disks that we want to disable and dynamically unplug them.
Changes in v2:
- use PCI_CLASS constants;
- replace pci_unplug_device with qdev_unplug;
- do not import hw/ide/internal.h in xen_platform.c;
Changes in v3:
- introduce piix3-ide-xen, that support hot-unplug;
- move the unplug code to hw/ide/piix.c;
- just call qdev_unplug from xen_platform.c to unplug the IDE disks;
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Just in case there's still a way how a guest can read out buffers when it's not
supposed to, let's zero the buffers during initialisation so that we don't leak
information to the guest.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This fixes https://bugs.launchpad.net/qemu/+bug/786209:
When the DRQ_STAT bit is set, the IDE core permits both data reads
and data writes, regardless of whether the current transfer was
initiated as a read or write.
This potentially leaks uninitialized host memory into the guest,
if, before doing anything else to an IDE device, the guest begins a
write transaction (e.g. WIN_WRITE), but then *reads* from the IO
port instead of writing to it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Clearing the error status flag was missing for restarting flushes. Now that the
error status is separate from the BM status register, we can simply set it to 0
after restarting the request. This ensures that we never forget to clear a bit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add support for TRIM sub function of the data set management command,
and wire it up to the qemu discard infrastructure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace the is_read flag with a dma_cmd flag to allow the dma and
restart logic to handler other commands like TRIM.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When a failed PIO request caused the VM to stop, we still need to transfer the
PIO state even though DRQ=0 at this point.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When adding the werror=stop mode, some flags were added to s->status
which are used to determine what kind of operation should be restarted
when the VM is continued.
Unfortunately, it turns out that s->status is in fact a device register
and as such is visible to the guest (some of the abused bits are even
writable for the guest).
For migration we keep on using the old VMState field (renamed to
migration_compat_status) if the status register doesn't use any of the
previously abused bits. If it does, we use a subsection with a clean copy of
the status register.
The error status is always sent in a subsection if there is any error. It can't
use the old field because errors happen even without PCI.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. Unlike
DriveInfo, BlockDriverState should be about the host part only.
One of the remaining guest bits there is the "type hint". -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.
Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Fix regression of 667bb59: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The commit 667bb59d23
uses d->ahci.mem before it is initialized by
ahci_init(). Fix this by calling ahci_init() first thing
so that it's safe to use all fields in the ahci state struct.
Reported-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After the re-org of the atapi code, it might not be intuitive for a
reader of the code to understand why we're inserting a 'media not
present' state between cd changes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some commands are supposed to report a Not Ready Condition (i.e. they require
a medium to be present in order to execute successfully). Instead of
duplicating the check in each command implementation, let's add a flag and
check it before calling the command.
This patch only converts existing checks, it does not introduce new checks for
any of the other commands that can/should report a Not Ready Condition.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The disk size can only change when the medium is changed, and the change
callback takes care of updating s->nb_sectors in this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for a table of function pointers, factor each command out from
ide_atapi_cmd() into its own function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>