Create vexpress specific pflash registration
function which properly configures the device-width
of 16 bits (2 bytes) for the NOR flash on the
vexpress platform. This change is required for
buffered flash writes to work properly.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-5-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we know how wide each flash device that makes up the bank is,
return status for each device in the bank. Leave existing code
that treats 32 bit wide banks as composed of two 16 bit devices as otherwise
we may break configurations that do not set the device_width propery.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-4-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The width of the devices that make up the flash interface
is required to mask certain commands, in particular the
write length for buffered writes. This length will be presented
to each device on the interface by the program writing the flash,
and the flash emulation code needs to be able to determine
the length of the write as recieved by each flash device.
The device-width defaults to the bank width which should
maintain existing behavior for platforms that don't need
this change.
This change is required to support buffered writes on the
vexpress platform that has a 32 bit flash interface with 2
16 bit devices on it.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-3-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the 'width' member of the pflash_t structure
in preparation for adding a bank_width member.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1386279359-32286-2-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for the AESE/AESD/AESMC/AESIMC instructions that
are available on some v8 implementations of Aarch32.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1386266078-6976-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu_opts_parse() can always return NULL, even if the QemuOptsList.desc in
question would be trivial to satisfy (eg. because it's empty). For
example:
qemu_opts_parse()
opts_parse()
qemu_opts_create()
id_wellformed()
In practice:
$ .../qemu-system-x86_64 -acpitable id=3
qemu-system-x86_64: -acpitable id=3: Parameter 'id' expects an identifier
**
ERROR:vl.c:3491:main: assertion failed: (opts != NULL)
Aborted (core dumped)
$ .../qemu-system-x86_64 -smbios id=3
qemu-system-x86_64: -smbios id=3: Parameter 'id' expects an identifier
Segmentation fault (core dumped)
I checked all qemu_opts_parse() invocations (and all drive_def()
invocations too, because it blindly forwards the former's retval). Only
the two above examples look problematic.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1385658779-7529-1-git-send-email-lersek@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
nbd patches in preparation of spice-nbd.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=J7aY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'spice/tags/pull-spice-1' into staging
Collection of little cleanups anf bugfixes.
nbd patches in preparation of spice-nbd.
# gpg: Signature made Mon 16 Dec 2013 01:27:45 AM PST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
# By Marc-André Lureau (12) and Gerd Hoffmann (4)
# Via Gerd Hoffmann
* spice/tags/pull-spice-1:
spice: stop server for qxl hard reset
spice: move spice_server_vm_{start,stop} calls into qemu_spice_display_*()
spice: move qemu_spice_display_*() from spice-graphics to spice-core
nbd: avoid uninitialized warnings
nbd: finish any pending coroutine
nbd: make nbd_client_session_close() idempotent
nbd: pass export name as init argument
nbd: don't change socket block during negotiate
Split nbd block client code
spice-char: implement chardev port event
char: add qemu_chr_fe_event()
include: add missing config-host.h include
qmp_change_blockdev() remove unused has_format
spice-char: remove unused field
vscclient: do not add a socket watch if there is not data to send
spice: flip streaming video mode to off by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=XYe2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kwolf/tags/for-anthony' into staging
Block patches
# gpg: Signature made Fri 13 Dec 2013 09:47:03 AM PST using RSA key ID C88F2FD6
# gpg: Can't check signature: public key not found
# By Peter Lieven (2) and others
# Via Kevin Wolf
* kwolf/tags/for-anthony:
blkdebug: Use QLIST_FOREACH_SAFE to resume IO
qemu-img: make progress output more accurate during convert
block: expect get_block_status errors in bdrv_make_zero
block/vvfat: Fix compiler warnings for OpenBSD
qapi-schema.json: Change 1.8 reference to 2.0
sheepdog: check if '-o redundancy' is passed from user
Message-id: 1386956943-19474-1-git-send-email-kwolf@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Hard reset can happen at any time. We should be able to put qxl into a
known-good state no matter what. Stop spice server thread for reset so
it can't be confused by fetching stale commands lingering around in the
rings while we reset is ongoing.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make sure all pending coroutines are finished when closing the session.
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no need to keep the export name around, and it seems a better
fit as an argument in the init() call.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The caller might handle non-blocking using coroutine. Leave the choice
to the caller to use a blocking or non-blocking negotiate.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Teach the chardev frontend to send event. This is used by the Spice port
chardev currently.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Video streaming detection heuristics in spice-server have problems
keeping modern desktop animations (as done by gnome shell) and real
video playback apart. This leads to jpeg compression artefacts on
your desktop, due to spice using mjpeg to send what it thinks is
a video stream.
Turn off video detection by default to avoid these artifacts.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Alon Levy <alevy@redhat.com>
Most notably this includes changes to exec to support
full 64 bit addresses.
This also flushes out patches that got queued during 1.7 freeze.
There are new tests, and a bunch of bug fixes all over the place.
There are also some changes mostly useful for downstreams.
I'm also listing myself as pc co-maintainer. I'm doing this reluctantly,
but this seems to be necessary to make sure patches are not lost or delayed too
much, and posting the MAINTAINERS patch did not seem to make anyone else
volunteer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSqK0/AAoJECgfDbjSjVRpz0wH/2BCUmgQ8oZfe9PrRhdCpYbw
6RtDLVucIUNq3CYfeV+Lua1Dw62CPVNGUR1Y2sk9s5X0C/lHLXeUkZxYy0JezGmW
k0EZAcVC4kXqyPbVh83I2pKtTwLGfI6I1qzsLZc+6CDT34YN7Lwe+wRJXQQNGcJc
gEbe4U8xuufdPZO2zv9RWEwmI4tI38PxnDJw+MYNJOKNnweLBRKq10YEKrref7Ml
4O1GxAXfQd0wkAhr9Cm7ZBajOzy/ovLj/b7HmiCMOvGkOaVhzurqbOtxlsbVIF9T
26+HEhu+2H/NO4qk5VmZjSngayUySBdEbGLHiovd8Xl4zMFPFNfQXv1mR3Vzb20=
=GPZ/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi.pci,pc,memory core fixes
Most notably this includes changes to exec to support
full 64 bit addresses.
This also flushes out patches that got queued during 1.7 freeze.
There are new tests, and a bunch of bug fixes all over the place.
There are also some changes mostly useful for downstreams.
I'm also listing myself as pc co-maintainer. I'm doing this reluctantly,
but this seems to be necessary to make sure patches are not lost or delayed too
much, and posting the MAINTAINERS patch did not seem to make anyone else
volunteer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 11 Dec 2013 10:21:51 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (14) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony: (28 commits)
pc: use macro for HPET type
hpet: fix build with CONFIG_HPET off
acpi unit-test: adjust the test data structure for better handling
acpi unit-test: load and check facs table
exec: separate sections and nodes per address space
memory.c: bugfix - ref counting mismatch in memory_region_find
hpet: enable to entitle more irq pins for hpet
hpet: inverse polarity when pin above ISA_NUM_IRQS
pci: fix pci bridge fw path
ACPI DSDT: Make control method `IQCR` serialized
acpi: strip compiler info in built-in DSDT
acpi unit-test: verify signature and checksum
smbios: Set system manufacturer, product & version by default
exec: reduce L2_PAGE_SIZE
exec: make address spaces 64-bit wide
exec: memory radix tree page level compression
exec: pass hw address to phys_page_find
exec: extend skip field to 6 bit, page entry to 32 bit
exec: replace leaf with skip
split definitions for exec.c and translate-all.c radix trees
...
Message-id: cover.1386786228.git.mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Paolo Bonzini (4) and Peter Lieven (1)
# Via Paolo Bonzini
* bonzini/scsi-next:
help: add id suboption to -iscsi
scsi-disk: fix WRITE SAME with large non-zero payload
block/iscsi: introduce bdrv_co_{readv, writev, flush_to_disk}
scsi-disk: fix VERIFY emulation
scsi-bus: fix transfer length and direction for VERIFY command
Message-id: 1386594157-17535-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Qemu-iotest 030 was broken.
When the coroutine runs and finishes, it will remove itself from the req
list, so let's use safe version of foreach to avoid use after free.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
the progress output is very bumpy if the input images contains
a significant portion of unallocated sectors. This patch
checks how much sectors are allocated a priori if progress
output is selected.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
during testing around with 4k LUNs a bad target implementation
triggert an -EIO in iscsi_get_block_status, but it got never caught
resulting in an infinite loop.
CC: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The buildbot shows these compiler warnings:
block/vvfat.c: In function 'create_short_and_long_name':
block/vvfat.c:620: warning: array size (8) smaller than bound length (11)
block/vvfat.c:620: warning: array size (8) smaller than bound length (11)
block/vvfat.c:635: warning: array size (8) smaller than bound length (11)
block/vvfat.c:635: warning: array size (8) smaller than bound length (11)
They are caused by tricky code where 8 characters for the name are followed
by 3 characters for the extension, and some operations touch both name and
extension.
Using an 11 character name which includes the extension fixes the compiler
warning, satisfies cppcheck, valgrind and maybe other static and dynamic
code checkers, and even simplifies some parts of the code.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fix a segfault (that is caused by b3af018f3) of following command:
$ qemu-img convert some_img sheepdog:some_img
Cc: qemu-devel@nongnu.org
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ability of the new opcodes to byte-swap the memory operation
simplifies the code in and around dec_load and dec_store significantly.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
make hpet_find inline so we don't need
to build hpet.c to check if hpet is enabled.
Fixes link error with CONFIG_HPET off.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ensure more then one instance of test_data may exist
at a given time. It will help to compare different
acpi table versions.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
FACS table does not have a checksum, so we can
check at least the signature (existence).
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Every address space has its own nodes and sections, but
it uses the same global arrays of nodes/section.
This limits the number of devices that can be attached
to the guest to 20-30 devices. It happens because:
- The sections array is limited to 2^12 entries.
- The main memory has at least 100 sections.
- Each device address space is actually an alias to
main memory, multiplying its number of nodes/sections.
Remove the limitation by using separate arrays of
nodes and sections for each address space.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'address_space_get_flatview' gets a reference to a FlatView.
If the flatview lookup fails, the code returns without
"unreferencing" the view.
Cc: qemu-stable@nongnu.org
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Owning to some different hardware design, piix and q35 need
different compat. So making them diverge.
On q35, IRQ2/8 can be reserved for hpet timer 0/1. And pin 16~23
can be assigned to hpet as guest chooses. So we introduce intcap
property to do that.
Consider the compat and piix/q35, we finally have the following
value for intcap: For piix, hpet's intcap is hard coded as IRQ2.
For pc-q35-1.7 and earlier, we use IRQ2 for compat reason. Otherwise
IRQ2, IRQ8, and IRQ16~23 are allowed.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to hpet spec, hpet irq is high active. But according to
ICH spec, there is inversion before the input of ioapic. So the OS
will expect low active on this IRQ line. (On bare metal, if OS driver
claims high active on this line, spurious irq is generated)
We fold the emulation of this inversion inside the hpet logic.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qemu uses "pci" as name for pci bridges in the firmware device path.
seabios expects "pci-bridge". Result is that bootorder is broken for
devices behind pci bridges.
Some googling suggests that "pci-bridge" is the correct one. At least
PPC-based Apple machines are using this. See question "How do I boot
from a device attached to a PCI card" here:
http://www.netbsd.org/ports/macppc/faq.html
So lets change qemu to use "pci-bridge" too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-temp-order:
tcg: Use bitmaps for free temporaries
Message-id: 1386698065-6661-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Vincenzo Maffione (2) and others
# Via Stefan Hajnoczi
* stefanha/net-next:
net: Update netdev peer on link change
virtio-net: don't update mac_table in error state
MAINTAINERS: Add netmap maintainers
net: Adding netmap network backend
Message-id: 1386594692-21278-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Emulation bugfixes for intel-hda and adlib.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zExI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kraxel/tags/pull-audio-1' into staging
Change audio wakeup rate from 250 Hz to 100 Hz.
Emulation bugfixes for intel-hda and adlib.
# gpg: Signature made Mon 09 Dec 2013 06:04:16 AM PST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
# By Gerd Hoffmann (2) and others
# Via Gerd Hoffmann
* kraxel/tags/pull-audio-1:
intel-hda: fix position buffer
adlib: fix patching of port I/O addresses
audio: adjust pulse to 100Hz wakeup rate
audio: Lower default wakeup rate to 100 times / second
Message-id: 1386597974-26506-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Stefan Weil
# Via Alon Levy
* alon/libcacard_ccid.4:
libcacard: Fix compilation for older versions of glib (bug #1258168)
Message-id: 1386596263-26151-1-git-send-email-alevy@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Stefan Weil
# Via Michael Tokarev
* mjt/trivial-patches:
qxl: Add missing trace.h (fix broken build)
Message-id: 1386441094-9971-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
We previously allocated 32-bits per temp for the next_free_temp entry.
We now allocate 4 bits per temp across the 4 bitmaps.
Using a linked list meant that if a translator is tweeked, resulting in
temps being freed in a different order, that would have follow-on effects
throughout the TB. Always allocating the lowest free temp means that
follow-on effects are minimized, which can make it easier to diff output
when debugging the translators.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
