When determining the group priority of a group 1 IRQ, if C_CTRL.CBPR is
0, the non-secure BPR value is used. However, this value must be
incremented by one so that it matches the secure world number of
implemented priority bits (NS world has one less priority bit compared
to the Secure world).
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-5-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: add assert, as the gicv3 code has]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When there is no active interrupts in the GIC, a read to the C_RPR
register should return the value of the "Idle priority", which is either
the maximum value an IRQ priority field can be set to, or 0xff.
Since the QEMU GIC model implements all the 8 priority bits, the Idle
priority is 0xff.
Internally, when there is no active interrupt, the running priority
value is 0x100. The gic_get_running_priority function returns an uint8_t
and thus, truncate this value to 0x00 when returning it. This is wrong since
a value of 0x00 correspond to the maximum possible priority.
This commit fixes the returned value when the internal value is 0x100.
Note that it is correct for the Non-Secure view to return 0xff even
though from the NS world point of view, only 7 priority bits are
implemented. The specification states that the Idle priority can be 0xff
even when not all the 8 priority bits are implemented. This has been
verified against a real GICv2 hardware on a Xilinx ZynqMP based board.
Regarding the ARM11MPCore version of the GIC, the specification is not
clear on that point, so this commit does not alter its behavior.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-4-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the GIC, when an IRQ is acknowledged, its state goes from "pending"
to:
- "active" if the corresponding IRQ pin has been de-asserted
- "active and pending" otherwise.
The GICv2 manual states that when a IRQ becomes active (or active and
pending), the GIC should either signal another (higher priority) IRQ to
the CPU if there is one, or de-assert the CPU IRQ pin.
The current implementation of the GIC in QEMU does not check if the
IRQ is already active when looking for pending interrupts with
sufficient priority in gic_update(). This can lead to signaling an
interrupt that is already active.
This usually happens when splitting priority drop and interrupt
deactivation. On priority drop, the IRQ stays active until deactivation.
If it becomes pending again, chances are that it will be incorrectly
selected as best_irq in gic_update().
This commit fixes this by checking if the IRQ is not already active when
looking for best_irq in gic_update().
Note that regarding the ARM11MPCore GIC version, the corresponding
manual is not clear on that point, but it has has no priority
drop/interrupt deactivation separation, so this case should not happen.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-3-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-16-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-15-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-14-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not enabled anywhere so far.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the same time, move VMSTATE_UINT32_SUB_ARRAY
beside the other UINT32 definitions.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-8-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Helpers that return a pointer into env->vfp.regs so that we isolate
the logic of how to index the regs array for different cpu modes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-7-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All direct users of this field want an integral value. Drop all
of the extra casting between uint64_t and float64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-6-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than passing a regno to the helper, pass pointers to the
vector register directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-5-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than passing regnos to the helpers, pass pointers to the
vector registers directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180119045438.28582-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than passing regnos to the helpers, pass pointers to the
vector registers directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180119045438.28582-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If it isn't used when translate.h is included,
we'll get a compiler Werror.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180119045438.28582-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The actual imx_eth_enable_rx() function is buggy.
It updates s->regs[ENET_RDAR] after calling qemu_flush_queued_packets().
qemu_flush_queued_packets() is going to call imx_XXX_receive() which itself
is going to call imx_eth_enable_rx().
By updating s->regs[ENET_RDAR] after calling qemu_flush_queued_packets()
we end up updating the register with an outdated value which might
lead to disabling the receive function in the i.MX FEC/ENET device.
This patch change the place where the register update is done so that the
register value stays up to date and the receive function can keep
running.
Reported-by: Fyleo <fyleo45@gmail.com>
Tested-by: Fyleo <fyleo45@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20180113113445.2705-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit ("3b39d734141a target/arm: Handle page table walk load failures
correctly") modified both versions of the page table walking code (i.e.,
arm_ldl_ptw and arm_ldq_ptw) to record the result of the translation in
a temporary 'data' variable so that it can be inspected before being
returned. However, arm_ldq_ptw() returns an uint64_t, and using a
temporary uint32_t variable truncates the upper bits, corrupting the
result. This causes problems when using more than 4 GB of memory in
a TCG guest. So use a uint64_t instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20180119194648.25501-1-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Start a vm with qemu-kvm -enable-kvm -vnc :66 -smp 1 -m 1024 -hda
redhat_5.11.qcow2 -device pcnet -vga cirrus,
then use VNC client to connect to VM, and excute the code below in guest
OS will lead to qemu crash:
int main()
{
iopl(3);
srand(time(NULL));
int a,b;
while(1){
a = rand()%0x100;
b = 0x3c0 + (rand()%0x20);
outb(a,b);
}
return 0;
}
The above code is writing the registers of VGA randomly.
We can write VGA CRT controller registers index 0x0C or 0x0D
(which is the start address register) to modify the
the display memory address of the upper left pixel
or character of the screen. The address may be out of the
range of vga ram. So we should check the validation of memory address
when reading or writing it to avoid segfault.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Message-id: 20180111132724.13744-1-linzhecheng@huawei.com
Fixes: CVE-2018-5683
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
-----BEGIN PGP SIGNATURE-----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=gjNZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Tue 23 Jan 2018 12:38:36 GMT
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (29 commits)
iotests: Disable some tests for compat=0.10
iotests: Split 177 into two parts for compat=0.10
iotests: Make 059 pass on machines with little RAM
iotests: Filter compat-dependent info in 198
iotests: Make 191 work with qcow2 options
iotests: Make 184 image-less
iotests: Make 089 compatible with compat=0.10
iotests: Fix 067 for compat=0.10
iotests: Fix 059's reference output
iotests: Fix 051 for compat=0.10
iotests: Fix 020 for vmdk
iotests: Skip 103 for refcount_bits=1
iotests: Forbid 020 for non-file protocols
iotests: Drop format-specific in _filter_img_info
iotests: Fix _img_info for backslashes
block/vmdk: Add blkdebug events
block/qcow: Add blkdebug events
qcow2: No persistent dirty bitmaps for compat=0.10
block/vmdk: Fix , instead of ; at end of line
qemu-iotests: Fix locking issue in 102
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
[for addition of trace-events to hw/pci-host]
Acked-by: Michael S. Tsirkin <mst@redhat.com>
This is the final stage in correcting the naming convention with respect to
sabre, APB and PBM. It is effectively a file rename from apb.c to sabre.c
along with touching up a few constants to remove the remaining references
to APB.
Note that as part of the rename process the configuration variable
CONFIG_PCI_APB is changed to CONFIG_PCI_SABRE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
In order to reflect the previous change of TYPE_APB to TYPE_SABRE, update
the corresponding variable names to keep the terminology consistent.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Similarly rename the corresponding APBState typedef to SabreState.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This is the proper name for the PBM host bridge as referenced in the Sun
documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
As hinted in the comment at the top of the file, the naming convention for the
APB types/QOM functions isn't correct. As a starting point we can at least
rename the APB type and related functions to improve the readability of apb.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Here we rename PBMPCIBridge to SimbaPCIBridge and the QOM type from
TYPE_PBM_PCI_BRIDGE to TYPE_SIMBA_PCI_BRIDGE in improve the clarity
of the device name.
Also touch up the relevant spots in apb.c and various other function
names as appropriate.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Move the QOM type and macros into a new include/hw/pci-bridge/simba.h
file, and add a new CONFIG_SIMBA Makefile.objs variable which is enabled
for sparc64-softmmu builds only.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
With the LEON3 IRQ controller IRQs can be acknowledged 2 ways:
* Explicitly by software writing to the CLEAR_OFFSET register
* Implicitly when the procesor is done running the trap handler attached
to the IRQ.
The actual IRQMP code only allows the implicit processor triggered IRQ ack.
If software write explicitly to the CLEAR_OFFSET register, this will clear
the pending bit in the register value but this will not lower the ongoing
raised IRQ with the processor. The IRQ will be kept raised to the LEON
processor until the related trap handler is run and the processor implicitly
ack the interrupt. So with the actual IRQMP code trap handler have to be run
even if the software has already done its job by clearing the pending bit.
This feature has been tested on another LEON3 simulator (tsim_leon3 from
Gaisler) and it turns out that the Qemu implementation is not equivalent to
the tsim one. In tsim, if software does clear a pending interrupt before
the related interrupt handler is triggered the said interrupt handler will
not be called.
This patch brings the Qemu IRQMP implementation in line with the tsim
implementation by allowing IRQ to be acknowledged by software only.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This reverts commit f87d72f5c5 as that is
part of a patchset reported to break cleanup and migration.
Cc: Gal Hammer <ghammer@redhat.com>
Cc: Sitong Liu <siliu@redhat.com>
Cc: Xiaoling Gao <xiagao@redhat.com>
Suggested-by: Greg Kurz <groug@kaod.org>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reported-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
This reverts commit 4fe6d78b2e as it is
reported to break cleanup and migration.
Cc: Gal Hammer <ghammer@redhat.com>
Cc: Sitong Liu <siliu@redhat.com>
Cc: Xiaoling Gao <xiagao@redhat.com>
Suggested-by: Greg Kurz <groug@kaod.org>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reported-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
This reverts commit 6f0bb23072.
This reverts commit f87d72f5c5 as that is
reported to break cleanup and migration.
Cc: Gal Hammer <ghammer@redhat.com>
Cc: Sitong Liu <siliu@redhat.com>
Cc: Xiaoling Gao <xiagao@redhat.com>
Suggested-by: Greg Kurz <groug@kaod.org>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reported-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
v2:
* Drop merge failure from a previous pull request that broke virtio-blk on ARM
guests
* Add Parallels XML patch series
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaZgqoAAoJEJykq7OBq3PIwNIIAKD8OwjeQdtznD88ikMGd5CF
PvBHOIXIX7GCaKdAFEP1MMB0xaTN93zhphPZfcQxnnbi2LrnzuP2WCSunKPPcGQJ
ToMRxYV+OkS0Rm8/us9fQpmBf2PKouIlNXP4jZZuEYAmyZgoU7YBQHYP1sw2K6RE
MHPBdKMKzb+S8u+HBx+oy1LQ0cKKRjCYXhdQ4p7rlWkXc5irQQh9d12W/EHS++cd
5wgX5V3aj4rXD4XwXY/kgDXtSG37sgNOHx77W7gDO3KuBolEBVvPvbP7yrCZzfcC
pGLPKwXnHTxOKlwLQ0weD+uIsJWv6XGKLhgX+MFWCVU1PvPuSTWcqfBplgTUU6s=
=mjmD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
Pull request
v2:
* Drop merge failure from a previous pull request that broke virtio-blk on ARM
guests
* Add Parallels XML patch series
# gpg: Signature made Mon 22 Jan 2018 16:00:40 GMT
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/block-pull-request:
block/parallels: add backing support to readv/writev
block/parallels: replace some magic numbers
block/parallels: move some structures into header
configure: add dependency
docs/interop/prl-xml: description of Parallels Disk format
block: add block_set_io_throttle virtio-blk-pci QMP example
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is needed for new architectures like RISC-V which do not provide any
other rename-like syscall.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <mvm607su9qs.fsf@suse.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
If multiple guest threads in user-mode emulation write to a
page which QEMU has marked read-only because of cached TCG
translations, the threads can race in page_unprotect:
* threads A & B both try to do a write to a page with code in it at
the same time (ie which we've made non-writeable, so SEGV)
* they race into the signal handler with this faulting address
* thread A happens to get to page_unprotect() first and takes the
mmap lock, so thread B sits waiting for it to be done
* A then finds the page, marks it PAGE_WRITE and mprotect()s it writable
* A can then continue OK (returns from signal handler to retry the
memory access)
* ...but when B gets the mmap lock it finds that the page is already
PAGE_WRITE, and so it exits page_unprotect() via the "not due to
protected translation" code path, and wrongly delivers the signal
to the guest rather than just retrying the access
In particular, this meant that trying to run 'javac' in user-mode
emulation would fail with a spurious guest SIGSEGV.
Handle this by making page_unprotect() assume that a call for a page
which is already PAGE_WRITE is due to a race of this sort and return
a "fault handled" indication.
Since this would cause an infinite loop if we ever called
page_unprotect() for some other kind of fault than "write failed due
to bad access permissions", tighten the condition in
handle_cpu_signal() to check the signal number and si_code, and add a
comment so that if somebody does ever find themselves debugging an
infinite loop of faults they have some clue about why.
(The trick for identifying the correct setting for
current_tb_invalidated for thread B (needed to handle the precise-SMC
case) is due to Richard Henderson. Paolo Bonzini suggested just
relying on si_code rather than trying anything more complicated.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1511879725-9576-3-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently all the architecture/OS specific cpu_signal_handler()
functions call handle_cpu_signal() without passing it the
siginfo_t. We're going to want that so we can look at the si_code
to determine whether this is a SEGV_ACCERR access violation or
some other kind of fault, so change the functions to pass through
the pointer to the siginfo_t rather than just the si_addr value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1511879725-9576-2-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
linux-user binaries don't need firmware and NMI,
so don't add them in this case, move QDEV
firmware functions to qdev-fw.c
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20171103193802.11876-1-laurent@vivier.eu>
Signed-off-by: Marco A L Barbosa <malbarbo@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20180111183714.22834-2-malbarbo@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
sched_get/setaffinity linux-user syscalls were missing conversions for
little/big endian, which is hairy since longs may not be the same size
either.
For simplicity, this just introduces loops to convert bit by bit like is
done for select.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20180109201643.1479-1-samuel.thibault@ens-lyon.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
mmap() is required by the linux kernel ABI and POSIX to return a
non-NULL address when the implementation chooses a start address for the
mapping.
The current implementation of mmap_find_vma_reserved() can return NULL
as start address of a mapping which leads to subsequent crashes inside
the guests glibc, e.g. output of qemu-arm-static --strace executing a
test binary stx_test:
1879 mmap2(NULL,8388608,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANONYMOUS|0x20000,-1,0) = 0x00000000
1879 write(2,0xf6fd39d0,79) stx_test: allocatestack.c:514: allocate_stack: Assertion `mem != NULL' failed.
This patch fixes mmap_find_vma_reserved() by skipping NULL as start
address while searching for a suitable mapping start address.
CC: Riku Voipio <riku.voipio@iki.fi>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Maximilian Riemensberger <riemensberger@cadami.net>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1515286904-86418-1-git-send-email-riemensberger@cadami.net>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The third argument to dup3() is a flags word which may be
O_CLOEXEC. We weren't translating this flag from target to
host value, which meant that if the target used a different
value from the host (eg sparc guest and x86 host) the dup3()
call would fail EINVAL. Do the correct translation.
Fixes: https://bugs.launchpad.net/qemu/+bug/1704658
Reported-by: Bruno Haible <bruno@clisp.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1513351080-25917-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Linux struct cmsghdr is already guaranteed to be sufficiently
aligned that CMSG_ALIGN(sizeof struct cmsghdr) is always equal
to sizeof struct cmsghdr. Stop doing the unnecessary alignment
arithmetic for host and target cmsghdr.
This follows kernel commit 1ff8cebf49ed9e9ca2 and brings our
TARGET_CMSG_* macros back into line with the kernel ones,
as well as making them easier to understand.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1513345976-22958-3-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The handling of length calculations in host_to_target_cmsg()
was rather confused:
* when checking for whether the target cmsg header fit in
the remaining buffer, we were using the host struct size,
not the target size
* we were setting tgt_len to "target payload + header length"
but then using it as if it were the target payload length alone
* in various message type cases we weren't handling the possibility
that host or target buffers were truncated
Fix these problems. The second one in particular is liable
to result in us overrunning the guest provided buffer,
since we will try to convert more data than is actually
present.
Fixes: https://bugs.launchpad.net/qemu/+bug/1701808
Reported-by: Bruno Haible <bruno@clisp.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1513345976-22958-2-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When we do a fork() in usermode emulation, we need to be in
a start/end exclusive section, so that we can ensure that no
other thread is in an RCU section. Otherwise you can get this
deadlock:
- fork thread: has mmap_lock, waits for rcu_sync_lock
(because rcu_init_lock() is registered as a pthread_atfork() hook)
- RCU thread: has rcu_sync_lock, waits for rcu_read_(un)lock
- another CPU thread: in RCU critical section, waits for mmap_lock
This can show up if you have a heavily multithreaded guest program
that does a fork().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Stuart Monteith <stuart.monteith@linaro.org>
Message-Id: <1512650481-1723-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Our locking order is that the tb lock should be taken
inside the mmap_lock, but fork_start() grabs locks the
other way around. This means that if a heavily multithreaded
guest process (such as Java) calls fork() it can deadlock,
with the thread that called fork() stuck in fork_start()
with the tb lock and waiting for the mmap lock, but some
other thread in tb_find() with the mmap lock and waiting
for the tb lock. The cpu_list_lock() should also always be
taken last, not first.
Fix this by making fork_start() grab the locks in the
right order. The order in which we drop locks doesn't
matter, so we leave fork_end() the way it is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <1512397331-15238-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaZx3vAAoJEPQH2wBh1c9AmwMIAJEYXNcSMyxQWqzixfMri5qs
pefoyv5gfzi3Gn7BQFluX+78mv0K828rueTfM3infydaqmPEacaPWtHMzDFWgsN8
9DIFldXGJBo+vFaJkxXNZjT/jbQWhgqnfspOvYdBqvoVwBbUmYTf366aClNvYjn8
Q/h3U/2KkNd3HddT7aFIn5S/4VQT8wEtkgcpnVSV642rldTw+Sa7qt6UX6/7nGVD
afcV1ZJ/Ap48GcaPsbzQms2jt2WG6T0XzzjdGzhhq2qZmOy9IlnxZKRPwXCFbhV1
0QoZBTYa+jX4Jeyp2agbZ2cJI/g2sAxwtbSEavBBl+E7iqzRXdODJ/8vM7fcwmY=
=iJB4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mreitz/tags/pull-block-2018-01-23' into queue-block
Block patches
# gpg: Signature made Tue Jan 23 12:35:11 2018 CET
# gpg: using RSA key F407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* mreitz/tags/pull-block-2018-01-23: (25 commits)
iotests: Disable some tests for compat=0.10
iotests: Split 177 into two parts for compat=0.10
iotests: Make 059 pass on machines with little RAM
iotests: Filter compat-dependent info in 198
iotests: Make 191 work with qcow2 options
iotests: Make 184 image-less
iotests: Make 089 compatible with compat=0.10
iotests: Fix 067 for compat=0.10
iotests: Fix 059's reference output
iotests: Fix 051 for compat=0.10
iotests: Fix 020 for vmdk
iotests: Skip 103 for refcount_bits=1
iotests: Forbid 020 for non-file protocols
iotests: Drop format-specific in _filter_img_info
iotests: Fix _img_info for backslashes
block/vmdk: Add blkdebug events
block/qcow: Add blkdebug events
qcow2: No persistent dirty bitmaps for compat=0.10
block/vmdk: Fix , instead of ; at end of line
qemu-iotests: Fix locking issue in 102
...
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
