This makes sure the regions are properly cleaned when unplugging -device
seconday-vga.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180626060941.8326-1-kraxel@redhat.com
According to the sm501 specs the hardware cursor colors are to be given in
the rgb565 format, but the code currently interprets them as bgr565.
Therefore, the colors of the hardware cursors are wrong in the QEMU
display, e.g., the standard mouse pointer of AmigaOS appears blue instead
of red. This change fixes this issue by replacing the existing naive
bgr565 => rgb888 conversion with a standard rgb565 => rgb888 one that also
scales the color component values properly.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When writing registers that have read only bits we have to avoid
changing these bits as they may have non zero values. Make sure we use
the correct masks to mask out read only and reserved bits when
changing registers.
Also remove extra spaces from dram_control and arbitration_control
assignments.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A link property can be set during creation, with
object_property_add_link() and later with object_property_set_link().
add_link() doesn't add a reference to the target object, while
set_link() does.
Furthemore, OBJ_PROP_LINK_UNREF_ON_RELEASE flags, set during add_link,
says whether a reference must be released when the property is destroyed.
This can lead to leaks if the property was later set_link(), as the
added reference is never released.
Instead, rename OBJ_PROP_LINK_UNREF_ON_RELEASE to OBJ_PROP_LINK_STRONG
and use that has an indication on how the link handle reference
management in set_link().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180606152128.449-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just set the full_update flag if we need a new DisplaySurface. Create
a new surface when the flag is set instead of having two places where
qemu_create_displaysurface_from() is called.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180525131318.28437-1-kraxel@redhat.com
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After writing up the virtual mdev device emulating a display supporting
the bochs vbe dispi interface (mbochs.ko) and seeing how simple it
actually is I've figured that would be useful for qemu too.
So, here it is, -device bochs-display. It is basically -device VGA
without legacy vga emulation. PCI bar 0 is the framebuffer, PCI bar 2
is mmio with the registers. The vga registers are simply not there
though, neither in the legacy ioport location nor in the mmio bar.
Consequently it is PCI class DISPLAY_OTHER not DISPLAY_VGA.
So there is no text mode emulation, no weird video modes (planar,
256color palette), no memory window at 0xa0000. Just a linear
framebuffer in the pci memory bar. And the amount of code to emulate
this (and therefore the attack surface) is an order of magnitude smaller
when compared to vga emulation.
Compatibility wise it works with OVMF (latest git master).
The bochs-drm.ko linux kernel module can handle it just fine too.
So UEFI guests should not see any functional difference to VGA.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-4-kraxel@redhat.com
Create a new header file, move the bochs vbe dispi interface
defines to it, so they can be used outside vga code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-2-kraxel@redhat.com
depth == 0 is used to indicate 256 color modes. Our region calculation
goes wrong in that case. So detect that and just take the safe code
path we already have for the wraparound case.
While being at it also catch depth == 15 (where our region size
calculation goes wrong too). And make the comment more verbose,
explaining what is going on here.
Without this windows guest install might trigger an assert due to trying
to check dirty bitmap outside the snapshot region.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1575541
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180514103117.21059-1-kraxel@redhat.com
x_keymap.o is common to the SDL and GTK+ modules, and it causes the
QEMU binary to link to the X11 libraries. Add it separately to the
modules to keep the main QEMU binary smaller.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1526560782-18732-1-git-send-email-pbonzini@redhat.com
[ kraxel: fix lm32 target build (milkymist-tmu2) ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make sure we only ask the spice local renderer for display updates in
case we have a valid primary surface. Without that spice is confused
and throws errors in case a display update request (triggered by
screendump for example) happens in parallel to a mode switch and hits
the race window where the old primary surface is gone and the new isn't
establisted yet.
Cc: qemu-stable@nongnu.org
Fixes: https://bugzilla.redhat.com//show_bug.cgi?id=1567733
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180427115528.345-1-kraxel@redhat.com
Using the new graphic_console_close() function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Typically the scanline length and the line offset are identical. But
in case they are not our calculation for region_end is incorrect. Using
line_offset is fine for all scanlines, except the last one where we have
to use the actual scanline length.
Fixes: CVE-2018-7550
Reported-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Prasad J Pandit <pjp@fedoraproject.org>
Tested-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Message-id: 20180309143704.13420-1-kraxel@redhat.com
This adds support for emulating the Silicon Image SII9022 DVI/HDMI
bridge. It's not very clever right now, it just acknowledges
the switch into DDC I2C mode and back. Combining this with the
existing DDC I2C emulation gives the right behavior on the Versatile
Express emulation passing through the QEMU EDID to the emulated
platform.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-5-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: explictly reset ddc_req/ddc_skip_finish/ddc]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to a kernel bug we can never increase the size of capability
set 1, so introduce a new capability set in parallel, old userspace
will continue to use the old set, new userspace will start using
the new one when it detects a fixed kernel.
v2: don't use a define from virglrenderer, just probe it.
v3: fix compilation when virglrenderer disabled
v4: fix style warning, just use ?: op instead.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Message-id: 20180223023814.24459-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Simplify the users of memory_region_snapshot_and_clear_dirty, so
that they do not have to call memory_region_sync_dirty_bitmap
explicitly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This removes the last user of memory_region_test_and_clear_dirty
outside memory.c.
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
gcc 5.4.0-6ubuntu1~16.04.5 build with UBSAN enabled error:
CC hw/display/exynos4210_fimd.o
/home/petmay01/linaro/qemu-for-merges/hw/display/exynos4210_fimd.c: In
function ‘fimd_get_buffer_id’:
/home/petmay01/linaro/qemu-for-merges/hw/display/exynos4210_fimd.c:1105:5:
error: case label does not reduce to an integer constant
case FIMD_WINCON_BUF2_STAT:
Because FIMD_WINCON_BUF2_STAT case contains an integer
overflow, use U suffix to get the unsigned type.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20180116151152.4040-2-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
virtio-gpu has special code path that bypassed vIOMMU protection. So
for now let's disable iommu_platform for the device until we fully
support that (if needed).
After the patch, both virtio-vga and virtio-gpu won't allow to boot with
iommu_platform parameter set.
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 20180131040401.3550-1-peterx@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In preperation for having an ARM and MicroBlaze ZynqMP machine let's
split out the current ARM specific config options.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aF9Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180125' into staging
target-arm queue:
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
# gpg: Signature made Thu 25 Jan 2018 12:59:25 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180125: (21 commits)
pl110: Implement vertical compare/next base interrupts
xilinx_spips: Correct usage of an uninitialized local variable
sdhci: fix a NULL pointer dereference due to uninitialized AddresSpace object
hw/arm/virt: Check that the CPU realize method succeeded
hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
hw/intc/arm_gic: Fix C_RPR value on idle priority
hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
target/arm: Simplify fp_exception_el for user-only
target/arm: Hoist store to flags output in cpu_get_tb_cpu_state
target/arm: Move cpu_get_tb_cpu_state out of line
target/arm: Add ARM_FEATURE_SVE
vmstate: Add VMSTATE_UINT64_SUB_ARRAY
target/arm: Add aa{32, 64}_vfp_{dreg, qreg} helpers
target/arm: Change the type of vfp.regs
target/arm: Use pointers in neon tbl helper
target/arm: Use pointers in neon zip/uzp helpers
target/arm: Use pointers in crypto helpers
target/arm: Mark disas_set_insn_syndrome inline
i.MX: Fix FEC/ENET receive funtions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements rudimentary support for interrupt generation on the
PL110. I am working on a new DRI/KMS driver for Linux and since that
uses the blanking interrupt, we need something to fire here. Without
any interrupt support Linux waits for a while and then gives ugly
messages about the vblank not working in the console (it does not
hang perpetually or anything though, DRI is pretty forgiving).
I solved it for now by setting up a timer to fire at 60Hz and pull
the interrupts for "vertical compare" and "next memory base"
at this interval. This works fine and fires roughly the same number
of IRQs on QEMU as on the hardware and leaves the console clean
and nice.
People who want to create more accurate emulation can probably work
on top of this if need be. It is certainly closer to the hardware
behaviour than what we have today anyway.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180123225654.5764-1-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: folded long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Start a vm with qemu-kvm -enable-kvm -vnc :66 -smp 1 -m 1024 -hda
redhat_5.11.qcow2 -device pcnet -vga cirrus,
then use VNC client to connect to VM, and excute the code below in guest
OS will lead to qemu crash:
int main()
{
iopl(3);
srand(time(NULL));
int a,b;
while(1){
a = rand()%0x100;
b = 0x3c0 + (rand()%0x20);
outb(a,b);
}
return 0;
}
The above code is writing the registers of VGA randomly.
We can write VGA CRT controller registers index 0x0C or 0x0D
(which is the start address register) to modify the
the display memory address of the upper left pixel
or character of the screen. The address may be out of the
range of vga ram. So we should check the validation of memory address
when reading or writing it to avoid segfault.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Message-id: 20180111132724.13744-1-linzhecheng@huawei.com
Fixes: CVE-2018-5683
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
laying on the mailing list for a while, but apparently no
maintainer feels really responsible for picking up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=JCAM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth/tags/pull-request-2018-01-22' into staging
Pull request for various patches that have been reviewed and
laying on the mailing list for a while, but apparently no
maintainer feels really responsible for picking up.
# gpg: Signature made Mon 22 Jan 2018 11:10:16 GMT
# gpg: using RSA key 0x2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>"
# gpg: aka "Thomas Huth <thuth@redhat.com>"
# gpg: aka "Thomas Huth <huth@tuxfamily.org>"
# gpg: aka "Thomas Huth <th.huth@posteo.de>"
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth/tags/pull-request-2018-01-22:
hw/isa: Replace fprintf(stderr, "*\n" with error_report()
hw/ipmi: Replace fprintf(stderr, "*\n" with error_report()
hw/bt: Replace fprintf(stderr, "*\n" with error_report()
Fixes after renaming __FUNCTION__ to __func__
Replace all occurances of __FUNCTION__ with __func__
tests/cpu-plug-test: Test CPU hot-plugging on s390x
tests/cpu-plug-test: Check CPU hot-plugging on ppc64, too
tests/cpu-plug-test: Check the CPU hot-plugging with device_add, too
tests: Rename pc-cpu-test.c to cpu-plug-test.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Noticed by Coverity, forgotten in 5690d9ece
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fields points to an old interface that is no more
used in the current code.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
Message-id: 20171122135625.16625-1-fziglio@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These are not really implemented (just return zero or default values)
but add these so guests accessing them can run.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These were forgotten when adding panel layer support in ffd3925701
"SM501 emulation for R2D-SH4".
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[dwg: Added reference to earlier commit in message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and remove the old i386/pc dependency.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
since The VGACommonState struct has a GraphicHwOps *hw_ops member,
then remove the now unnecessary includes.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>