Status.FR bit must be ignored on write and read as 1 when an implementation of
Release 6 of the Architecture in which a 64-bit floating point unit is
implemented.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
In terms of encoding MIPS32R6 MIN.fmt, MAX.fmt, MINA.fmt, MAXA.fmt replaced
MIPS-3D RECIP1, RECIP2, RSQRT1, RSQRT2 instructions.
In R6 all Floating Point instructions are supposed to be IEEE-2008 compliant
i.e. FIR.HAS2008 always 1. However, QEMU softfloat for MIPS has not been
updated yet.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Introduce MIPS32R6 Compact Branch instructions which do not have delay slot -
they have forbidden slot instead. However, current implementation does not
support forbidden slot yet.
Add also BC1EQZ and BC1NEZ instructions.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In R6 the special behaviour for data references is also specified for Kernel
and Supervisor mode. Therefore MIPS_HFLAG_UX is replaced by generic
MIPS_HFLAG_AWRAP indicating enabled 32-bit address wrapping.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Also consider OPC_SPIM instruction as deleted in R6 because it is overlaping
with MIPS32R6 SDBBP.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Use "R6_" prefix in front of all new Multiply / Divide instructions for
easier differentiation between R6 and preR6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The encoding of PREF, CACHE, LLD and SCD instruction changed in MIPS32R6.
Additionally, the hint codes in PREF instruction greater than or
equal to 24 generate Reserved Instruction Exception.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Move DSP and Loongson instruction to *_legacy functions as they have been
removed in R6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
For better code readability and to avoid 'if' statements for all R6 and preR6
instructions whose opcodes are the same - decode_opc_special* functions are
split into functions with _r6 and _legacy suffixes.
*_r6 functions will contain instructions which were introduced in R6.
*_legacy functions will contain instructions which were removed in R6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Creating separate decode functions for special, special2 and special3
instructions to ease adding new R6 instructions and removing legacy
instructions.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The encoding of LL and SC instruction has changed in MIPS32 Release 6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signal Reserved Instruction Exception on instructions that do not exist in R6.
In this commit the following groups of preR6 instructions are marked as deleted:
- Floating Point Paired Single
- Floating Point Compare
- conditional moves / branches on FPU conditions
- branch likelies
- unaligned loads / stores
- traps
- legacy accumulator instructions
- COP1X
- MIPS-3D
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
GDB assumes that watchpoint set via the gdbstub remote protocol will
behave in the same way as hardware watchpoints for the target. In
particular, whether the CPU stops with the PC before or after the insn
which triggers the watchpoint is target dependent. Allow guest CPU
code to specify which behaviour to use. This fixes a bug where with
guest CPUs which stop before the accessing insn GDB would manually
step forward over what it thought was the insn and end up one insn
further forward than it should be.
We set this flag for the CPU architectures which set
gdbarch_have_nonsteppable_watchpoint in gdb 7.7:
ARM, CRIS, LM32, MIPS and Xtensa.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Michael Walle <michael@walle.cc> (for lm32)
Message-id: 1410545057-14014-1-git-send-email-peter.maydell@linaro.org
MIPS registers an unassigned access handler which raises a guest bus
error exception. However this causes QEMU to crash when KVM is enabled
as it isn't called from the main execution loop so longjmp() gets called
without a corresponding setjmp().
Until the KVM API can be updated to trigger a guest exception in
response to an MMIO exit, prevent the bus error exception being raised
from mips_cpu_unassigned_access() if KVM is enabled.
The check is at run time since the do_unassigned_access callback is
initialised before it is known whether KVM will be enabled.
The problem can be triggered with Malta emulation by making the guest
write to the reset region at physical address 0x1bf00000, since it is
marked read-only which is treated as unassigned for writes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM doesn't yet support the MIPS FPU, or writing to the guest's Config1
register which contains the FPU implemented bit. Clear QEMU's version of
that bit on reset and display a warning that the FPU has been disabled.
The previous incorrect Config1 CP0 register value wasn't being passed to
KVM yet, however we should ensure it is set correctly now to reduce the
risk of breaking migration/loadvm to a future version of QEMU/Linux that
does support it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The EBase CP0 register is initialised to 0x80000000, however with KVM
the guest's KSEG0 is at 0x40000000. The incorrect value doesn't get
passed to KVM yet as KVM doesn't implement the EBase register, however
we should set it correctly now so as not to break migration/loadvm to a
future version of QEMU that does support EBase.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid access to the CPUMIPSState structure in the
translator, keep a copy of CP0_Config1 into DisasContext. The whole
register is read-only so it can be copied as a single value.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* remotes/kvm/uq/master:
hw/mips: malta: Don't boot from flash with KVM T&E
MAINTAINERS: Add entry for MIPS KVM
target-mips: Enable KVM support in build system
hw/mips: malta: Add KVM support
hw/mips: In KVM mode, inject IRQ2 (I/O) interrupts via ioctls
target-mips: Call kvm_mips_reset_vcpu() from mips_cpu_reset()
target-mips: kvm: Add main KVM support for MIPS
kvm: Allow arch to set sigmask length
target-mips: get_physical_address: Add KVM awareness
target-mips: get_physical_address: Add defines for segment bases
hw/mips: Add API to convert KVM guest KSEG0 <-> GPA
hw/mips/cputimer: Don't start periodic timer in KVM mode
target-mips: Reset CPU timer consistently
KVM: Fix GSI number space limit
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From MIPS documentation (Volume III):
UserLocal Register (CP0 Register 4, Select 2)
Compliance Level: Recommended.
The UserLocal register is a read-write register that is not interpreted by
the hardware and conditionally readable via the RDHWR instruction.
This register only exists if the Config3-ULRI register field is set.
Privileged software may write this register with arbitrary information and
make it accessible to unprivileged software via register 29 (ULR) of the
RDHWR instruction. To do so, bit 29 of the HWREna register must be set to a
1 to enable unprivileged access to the register.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enable KVM support for MIPS in the build system.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM is enabled call kvm_mips_reset_vcpu() from mips_cpu_reset() as
done for other targets since commit 50a2c6e55f (kvm: reset state from
the CPU's reset method).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the main KVM arch API for MIPS.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MIPS KVM trap & emulate mode (which is currently the only supported
mode) has to add an extra kseg0/kseg1 at 0x40000000 and an extra
kseg2/kseg3 at 0x60000000. Take this into account in
get_physical_address() so that debug memory access works.
This is done by translating the address to a standard kseg0 or kseg2
address before doing the normal address translation. The real virtual
address is still used for TLB lookups.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add preprocessor definitions for 32bit segment bases for use in
get_physical_address(). These will also be taken advantage of in the
next patch which adds KVM awareness.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS CPU timer (CP0 Count/Compare registers & QEMU timer) is
reset at machine initialisation, including starting the timeout. Both
registers however are placed before mvp in CPUMIPSState so they will
both be zeroed on reset by the memset in mips_cpu_reset() including soon
after init. This doesn't take into account that the timer may be
running, in which case env->CP0_Count will represent the delta against
the VM clock and the timeout will need updating.
At init time (cpu_mips_clock_init()), lets only create the timer.
Setting Count = 1 and starting the timer (cpu_mips_store_count()) can be
done at reset time from cpu_state_reset(), which is after the memset.
There is also no need to set CP0_Compare = 0 as that is already handled
by the memset.
Note that a reset occurs from mips_cpu_realizefn() which is before the
machine init callback has had a chance to set up the CPU interrupts and
the CPU timer, so env->timer will be NULL. This case is handled
explicitly in cpu_mips_store_count(), treating the timer as disabled
(which will also be the right thing to do when KVM support is added).
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will collect all load and store helpers soon. For now
it is just a replacement for softmmu_exec.h, which this patch
stops including directly, but we also include it where this will
be necessary in order to simplify the next patch.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They do not need to be in op_helper.c. Because cputlb.c now includes
softmmu_template.h twice for each size, io_readX must be elided the
second time through.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Prepare for moving softmmu_header.h inclusion out of .c files
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will reference it from more files in the next patch. To avoid
ruining the small steps we're making towards multi-target, make
it a method of CPU rather than just a global.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than include helper.h with N values of GEN_HELPER, include a
secondary file that sets up the macros to include helper.h. This
minimizes the files that must be rebuilt when changing the macros
for file N.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add U suffix to various places where we shift a 1 left by 31,
to avoid undefined behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Previous implementation presumed that FPU registers are 64-bit and are
working in 64-bit mode. This change first checks MIPS_HFLAG_F64 and if not
set, it does load/store from the odd numbered register pair.
Patch by Matthew Fortune.
Signed-off-by: Matthew Fortune <matthew.fortune@imgtec.com>
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Most targets were using offsetof(CPUFooState, breakpoints) to determine
how much of CPUFooState to clear on reset. Use the next field after
CPU_COMMON instead, if any, or sizeof(CPUFooState) otherwise.
Signed-off-by: Andreas Färber <afaerber@suse.de>
