Currently the gpex PCI controller implements no special behaviour for
guest accesses to areas of the PIO and MMIO where it has not mapped
any PCI devices, which means that for Arm you end up with a CPU
exception due to a data abort.
Most host OSes expect "like an x86 PC" behaviour, where bad accesses
like this return -1 for reads and ignore writes. In the interests of
not being surprising, make host CPU accesses to these windows behave
as -1/discard where there's no mapped PCI device.
The old behaviour generally didn't cause any problems, because
almost always the guest OS will map the PCI devices and then only
access where it has mapped them. One corner case where you will see
this kind of access is if Linux attempts to probe legacy ISA
devices via a PIO window access. So far the only case where we've
seen this has been via the syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210325163315.27724-1-peter.maydell@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1918917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
-----BEGIN PGP SIGNATURE-----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=fIJT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210412' into staging
ppc patch queue for 2021-04-21
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
# gpg: Signature made Mon 12 Apr 2021 06:25:58 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210412:
spapr.c: always pulse guest IRQ in spapr_core_unplug_request()
spapr: rollback 'unplug timeout' for CPU hotunplugs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
The pseries machines introduced the concept of 'unplug timeout' for CPU
hotunplugs. The idea was to circunvent a deficiency in the pSeries
specification (PAPR), that currently does not define a proper way for
the hotunplug to fail. If the guest refuses to release the CPU (see [1]
for an example) there is no way for QEMU to detect the failure.
Further discussions about how to send a QAPI event to inform about the
hotunplug timeout [2] exposed problems that weren't predicted back when
the idea was developed. Other QEMU machines don't have any type of
hotunplug timeout mechanism for any device, e.g. ACPI based machines
have a way to make hotunplug errors visible to the hypervisor. This
would make this timeout mechanism exclusive to pSeries, which is not
ideal.
The real problem is that a QAPI event that reports hotunplug timeouts
puts the management layer (namely Libvirt) in a weird spot. We're not
telling that the hotunplug failed, because we can't be 100% sure of
that, and yet we're resetting the unplug state back, preventing any
DEVICE_DEL events to reach out in case the guest decides to release the
device. Libvirt would need to inspect the guest itself to see if the
device was released or not, otherwise the internal domain states will be
inconsistent. Moreover, Libvirt already has an 'unplug timeout'
concept, and a QEMU side timeout would need to be juggled together with
the existing Libvirt timeout.
All this considered, this solution ended up creating more trouble than
it solved. This patch reverts the 3 commits that introduced the timeout
mechanism for CPU hotplugs in pSeries machines.
This reverts commit 4515a5f786
"qemu_timer.c: add timer_deadline_ms() helper"
This reverts commit d1c2e3ce3d
"spapr_drc.c: add hotunplug timeout for CPUs"
This reverts commit 51254ffb32
"spapr_drc.c: introduce unplug_timeout_timer"
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1911414
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-03/msg04682.html
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210401000437.131140-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 4c70875372 ("pci: advertise a page aligned ATS") advertises
the page aligned via ATS capability (RO) to unbrek recent Linux IOMMU
drivers since 5.2. But it forgot the compat the capability which
breaks the migration from old machine type:
(qemu) qemu-kvm: get_pci_config_device: Bad config data: i=0x104 read:
0 device: 20 cmask: ff wmask: 0 w1cmask:0
This patch introduces a new parameter "x-ats-page-aligned" for
virtio-pci device and turns it on for machine type which is newer than
5.1.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
Fixes: 4c70875372 ("pci: advertise a page aligned ATS")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210406040330.11306-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide a new function dynamic_sysbus_dev_allowed() which checks the
per-machine list of permitted dynamic sysbus devices and returns a
boolean result indicating whether the device is allowed. We can use
this in the implementation of validate_sysbus_device(), but we will
also need it so that machine hotplug callbacks can validate devices
rather than assuming that any sysbus device might be hotpluggable
into the platform bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-3-peter.maydell@linaro.org
The function machine_class_allow_dynamic_sysbus_dev() is currently
undocumented; add a doc comment.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-2-peter.maydell@linaro.org
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no H_REGISTER_PROCESS_TABLE, it is H_REGISTER_PROC_TBL handler
for which is still called h_register_process_table() though.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210225032335.64245-1-aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The definition S390_ADAPTER_SUPPRESSIBLE was moved to "cpu.h", per
suggestion of Thomas Huth. From interface design perspective, IMHO, not
a good thing as it belongs to the public interface of
css_register_io_adapters(). We did this because CONFIG_KVM requeires
NEED_CPU_H and Thomas, and other commenters did not like the
consequences of that.
Moving the interrupt related declarations to s390_flic.h was suggested
by Cornelia Huck.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210317095622.2839895-2-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBZSuUACgkQIeENKd+X
cFQfqggAqiTI/KYe5GW9WBrPpGdctuEgUVBbxUhq5zY52mVGTfqEn4LbCfvdaTOp
O1MA+kfi4JN87VVWCfHPH0S725qmaPV7wfpWKi8KcPQ9uR+4RvjX/RDptkZhVjC9
Ok9p6dg2cUbz9Jm/q2V1Z69fRNMrz6pJWPxfZeTpy9bcmFNyYBR9+xiSXaW2fuAM
HsyZbsP8zHmHxfGcZwI6vpSZh3P4Ytd6nL/8v98i1DwWUsf51TsEwaS87gRQSjTz
SHqHZ9xsVM0k3glFi+El39iHzpujlONkYPvZaFP8kRhzXtaWVP1cu+CaKNUPEteq
jWNHLwFQk9VcN8uDG5o0unGEXnLJPA==
=dKa4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210322-2' into staging
RISC-V PR for 6.0
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
# gpg: Signature made Tue 23 Mar 2021 01:56:53 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210322-2:
target/riscv: Prevent lost illegal instruction exceptions
docs/system: riscv: Add documentation for 'microchip-icicle-kit' machine
hw/riscv: microchip_pfsoc: Map EMMC/SD mux register
hw/block: m25p80: Support fast read for SST flashes
target/riscv: Add proper two-stage lookup exception detection
target/riscv: Fix read and write accesses to vsip and vsie
hw/riscv: allow ramfb on virt
hw/riscv: Add fw_cfg support to virt
target/riscv: Use background registers also for MSTATUS_MPV
target/riscv: Make VSTIP and VSEIP read-only in hip
target/riscv: Adjust privilege level for HLV(X)/HSV instructions
target/riscv: flush TLB pages if PMP permission has been changed
target/riscv: add log of PMP permission checking
target/riscv: propagate PMP permission to TLB page
hw/char: disable ibex uart receive if the buffer is full
target/riscv: fix vs() to return proper error code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For accesses to rom blob data before or during reset, we have a
function rom_ptr() which looks for a rom blob that would be loaded to
the specified address, and returns a pointer into the rom blob data
corresponding to that address. This allows board or CPU code to say
"what is the data that is going to be loaded to this address?".
However, this function does not take account of memory region
aliases. If for instance a machine model has RAM at address
0x0000_0000 which is aliased to also appear at 0x1000_0000, a
rom_ptr() query for address 0x0000_0000 will only return a match if
the guest image provided by the user was loaded at 0x0000_0000 and
not if it was loaded at 0x1000_0000, even though they are the same
RAM and a run-time guest CPU read of 0x0000_0000 will read the data
loaded to 0x1000_0000.
Provide a new function rom_ptr_for_as() which takes an AddressSpace
argument, so that it can check whether the MemoryRegion corresponding
to the address is also mapped anywhere else in the AddressSpace and
look for rom blobs that loaded to that alias.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210318174823.18066-5-peter.maydell@linaro.org
A clock is added by commit aac63e0e6e ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6e ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Not disabling the UART leads to QEMU overwriting the UART receive buffer with
the newest received byte. The rx_level variable is added to allow the use of
the existing OpenTitan driver libraries.
Signed-off-by: Alexander Wagner <alexander.wagner@ulal.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210309152130.13038-1-alexander.wagner@ulal.de
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The code that sets/gets oem fields is duplicated in both PC and MICROVM
variants. This commit moves it to X86MachineState so that all x86
variants can use it and duplication is removed.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210221001737.24499-2-posteuca@mutex.one>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement _DSM according to:
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
and wire it up to cold and hot-plugged PCI devices.
Feature depends on ACPI hotplug being enabled (as that provides
PCI devices descriptions in ACPI and MMIO registers that are
reused to fetch acpi-index).
acpi-index should work for
- cold plugged NICs:
$QEMU -device e1000,acpi-index=100
=> 'eno100'
- hot-plugged
(monitor) device_add e1000,acpi-index=200,id=remove_me
=> 'eno200'
- re-plugged
(monitor) device_del remove_me
(monitor) device_add e1000,acpi-index=1
=> 'eno1'
Windows also sees index under "PCI Label Id" field in properties
dialog but otherwise it doesn't seem to have any effect.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be used by follow up patches
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In x86/ACPI world, linux distros are using predictable
network interface naming since systemd v197. Which on
QEMU based VMs results into path based naming scheme,
that names network interfaces based on PCI topology.
With itm on has to plug NIC in exactly the same bus/slot,
which was used when disk image was first provisioned/configured
or one risks to loose network configuration due to NIC being
renamed to actually used topology.
That also restricts freedom to reshape PCI configuration of
VM without need to reconfigure used guest image.
systemd also offers "onboard" naming scheme which is
preferred over PCI slot/topology one, provided that
firmware implements:
"
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
"
that allows to assign user defined index to PCI device,
which systemd will use to name NIC. For example, using
-device e1000,acpi-index=100
guest will rename NIC to 'eno100', where 'eno' is default
prefix for "onboard" naming scheme. This doesn't require
any advance configuration on guest side to com in effect
at 'onboard' scheme takes priority over path based naming.
Hope is that 'acpi-index' it will be easier to consume by
management layer, compared to forcing specific PCI topology
and/or having several disk image templates for different
topologies and will help to simplify process of spawning
VM from the same template without need to reconfigure
guest NIC.
This patch adds, 'acpi-index'* property and wires up
a 32bit register on top of pci hotplug register block
to pass index value to AML code at runtime.
Following patch will add corresponding _DSM code and
wire it up to PCI devices described in ACPI.
*) name comes from linux kernel terminology
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
According to the "Guide To The Macintosh Family Hardware", the 60Hz VIA1 timer
on newer Macs such as the Quadra only exists for compatibility with old software
and is no longer synced to the VBL interval.
Rename the VBL timer to 60Hz timer to emphasise this and to prevent confusion
when the real VBL interrupt (now handled as a NuBus slot interrupt) is added in
future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
For testing, it can be useful to simulate an enormous amount of memory
(e.g. 2^64 RAM). This adds an MMIO device that acts as sparse memory.
When something writes a nonzero value to a sparse-mem address, we
allocate a block of memory. For now, since the only user of this device
is the fuzzer, we do not track and free zeroed blocks. The device has a
very low priority (so it can be mapped beneath actual RAM, and virtual
device MMIO regions).
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a system controller for the m68k-virt machine.
This controller allows the kernel to power off or reset the machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-5-laurent@vivier.eu>
A (generic) copy of the GLUE device we already have for q800 to use with
the m68k-virt machine.
The q800 one would disappear in the future as q800 uses actually the djMEMC
controller.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-4-laurent@vivier.eu>
Implement the goldfish pic device as defined in
https://android.googlesource.com/platform/external/qemu/+/master/docs/GOLDFISH-VIRTUAL-HARDWARE.TXT
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-3-laurent@vivier.eu>
In preparation for splitting the usb-storage.c file move
declarations to the new usb/msd.h header file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210312090425.772900-2-kraxel@redhat.com>
No device needs them anymore and in fact they're undocumented.
Remove the code. The only change in behavior is that "-usbdevice
braille:hello" now reports an error, which is a bugfix.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210310173323.1422754-2-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This property was only required for the pc-1.0 and earlier machine
types. Since these have been removed now, we can delete the property
as well.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210302120152.118042-1-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Report the configured granularity for discard operation to the
guest. If this is not set use the block size.
Since until now we have ignored the configured discard granularity
and always reported the block size, let's add
'report-discard-granularity' property and disable it for older
machine types to avoid migration issues.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210225001239.47046-1-akihiko.odaki@gmail.com>
Add the yellow "lime" LED.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Rolnik <mrolnik@gmail.com>
Message-Id: <20210313165445.2113938-2-f4bug@amsat.org>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Multi Function Timer (MFT) module for NPCM7XX.
This module is mainly used to configure PWM fans. It has just enough
functionality to make the PWM fan kernel module work.
The module takes two input, the max_rpm of a fan (modifiable via QMP)
and duty cycle (a GPIO from the PWM module.) The actual measured RPM
is equal to max_rpm * duty_cycle / NPCM7XX_PWM_MAX_DUTY. The RPM is
measured as a counter compared to a prescaled input clock. The kernel
driver reads this counter and report to user space.
Refs:
https://github.com/torvalds/linux/blob/master/drivers/hwmon/npcm750-pwm-fan.c
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210311180855.149764-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
