This patch introduces the blk_drain() function which allows to replace
blk_drain_all() when only one BlockDriverState needs to be drained.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1434537440-28236-2-git-send-email-yarygin@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Calling throttle_group_config() cancels all timers from a particular
BlockDriverState, so any_timer_armed[] should be updated accordingly.
However, with the current code it may happen that a timer is armed in
a different BlockDriverState from the same group, so any_timer_armed[]
would be set to false in a situation where there is still a timer
armed.
The consequence is that we might end up with two timers armed. This
should not have any noticeable impact however, since all accesses to
the ThrottleGroup are protected by a lock, and the situation would
become normal again shortly thereafter as soon as all timers have been
fired.
The correct way to solve this is to check that we're actually
cancelling a timer before updating any_timer_armed[].
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 1434382875-3998-1-git-send-email-berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
After the commit 9b536adc ("block: acquire AioContext in
bdrv_drain_all()") the aio_poll() function got called for every
BlockDriverState, in assumption that every device may have its own
AioContext. If we have thousands of disks attached, there are a lot of
BlockDriverStates but only a few AioContexts, leading to tons of
unnecessary aio_poll() calls.
This patch changes the bdrv_drain_all() function allowing it find shared
AioContexts and to call aio_poll() only for unique ones.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1433936297-7098-4-git-send-email-yarygin@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Remove it except for two things in qerror.h:
* Two #include to be cleaned up separately to avoid cluttering this
patch.
* The QERR_ macros. Mark as obsolete.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
We require a C99 compiler, so let's use 'bool' instead of 'int'
when dealing with boolean values. There are few enough clients
to fix them all in one pass.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=QgYk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer core and image format patches
# gpg: Signature made Fri Jun 12 16:08:53 2015 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (25 commits)
block: Fix reopen flag inheritance
block: Add BlockDriverState.inherits_from
block: Add list of children to BlockDriverState
queue.h: Add QLIST_FIX_HEAD_PTR()
block: Drain requests before swapping nodes in bdrv_swap()
block: Move flag inheritance to bdrv_open_inherit()
block: Use QemuOpts in bdrv_open_common()
block: Use macro for cache option names
vmdk: Use bdrv_open_image()
quorum: Use bdrv_open_image()
check-qdict: Test cases for new functions
qdict: Add qdict_{set,copy}_default()
qdict: Add qdict_array_entries()
iotests: Add tests for overriding BDRV_O_PROTOCOL
block: driver should override flags in bdrv_open()
block: Change bitmap truncate conditional to assertion
block: record new size in bdrv_dirty_bitmap_truncate
raw-posix: Fix .bdrv_co_get_block_status() for unaligned image size
vmdk: Use vmdk_find_index_in_cluster everywhere
vmdk: Fix index_in_cluster calculation in vmdk_co_get_block_status
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When reopening an image, the block layer already takes care to reopen
bs->file as well with recalculated inherited flags. The same must happen
for any other child (most notably missing before this patch: backing
files).
If bs->file (or any other child) didn't originally inherit from bs, e.g.
because it was created separately and then only referenced, it must not
inherit flags on reopen either, so check the inherited_from field before
propagation the reopen down.
VMDK already reopened its extents manually; this code can now be
dropped.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Instead of letting every caller of bdrv_open() determine the right flags
for its child node manually and pass them to the function, pass the
parent node and the role of the newly opened child (like backing file,
protocol layer, etc.).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Besides standardising on a single interface for opening child nodes,
this patch allows the user to specify options to individual extent
nodes. Overriding file names isn't possible with this yet, so it's of
limited usefulness, but still a step forward.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Besides standardising on a single interface for opening child nodes,
this simplifies the .bdrv_open() implementation of the quorum block
driver by using block layer functionality for handling BlockdevRefs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Image files with an unaligned image size have a final hole that starts
at EOF, i.e. in the middle of a sector. Currently, *pnum == 0 is
returned when checking the status of this sector. In qemu-img, this
triggers an assertion failure.
In order to fix this, one type for the sector that contains EOF must be
found. Treating a hole as data is safe, so this patch rounds the
calculated number of data sectors up, so that a partial sector at EOF is
treated as a full data sector.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1229394
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Cole Robinson <crobinso@redhat.com>
It has the similar issue with b1649fae49. Since the calculation
is repeated for a few times already, introduce a function so it can be
reused.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If a relatively large cluster size is chosen, the default of 1 MB L2
cache is not really appropriate. In this case, unless overridden by the
user, the default cache size should not be determined by its size in
bytes but by the number of L2 tables (clusters) it is supposed to
contain.
Note that without this patch, MIN_L2_CACHE_SIZE will effectively take
over the same role. However, providing space for just two L2 tables is
not enough to be the default.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The L2 cache must cover at least two L2 tables, because during COW two
L2 tables are accessed simultaneously.
Reported-by: Alexander Graf <agraf@suse.de>
Cc: qemu-stable <qemu-stable@nongnu.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Tested-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_swap() touches the fields of a BlockDriverState that are
protected by the ThrottleGroup lock. Although those fields end up in
their original place, they are temporarily swapped in the process,
so there's a chance that an operation on a member of the same group
happening on a different thread can try to use them.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d92dc40d7c4f1fc5cda5cbbf4ffb7a4670b79d17.1433779731.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The throttle group support use a cooperative round robin scheduling
algorithm.
The principles of the algorithm are simple:
- Each BDS of the group is used as a token in a circular way.
- The active BDS computes if a wait must be done and arms the right
timer.
- If a wait must be done the token timer will be armed so the token
will become the next active BDS.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: f0082a86f3ac01c46170f7eafe2101a92e8fde39.1433779731.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Group throttling will share ThrottleState between multiple bs.
As a consequence the ThrottleState will be accessed by multiple aio
context.
Timers are tied to their aio context so they must go out of the
ThrottleState structure.
This commit paves the way for each bs of a common ThrottleState to
have its own timer.
Signed-off-by: Benoit Canet <benoit.canet@nodalink.com>
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 6cf9ea96d8b32ae2f8769cead38f68a6a0c8c909.1433779731.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Image files with an unaligned image size have a final hole that starts
at EOF, i.e. in the middle of a sector. Currently, *pnum == 0 is
returned when checking the status of this sector. In qemu-img, this
triggers an assertion failure.
In order to fix this, one type for the sector that contains EOF must be
found. Treating a hole as data is safe, so this patch rounds the
calculated number of data sectors up, so that a partial sector at EOF is
treated as a full data sector.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1229394
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1433840108-9996-1-git-send-email-kwolf@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Retain the function value for now, to permit selective conversion of
its callers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
When the argument is non-zero, qemu_opts_foreach() stops on callback
returning non-zero, and returns that value.
When the argument is zero, it doesn't stop, and returns the bit-wise
inclusive or of all the return values. Funky :)
The callers that pass zero could just as well pass one, because their
callbacks can't return anything but zero:
* qemu_add_globals()'s callback qdev_add_one_global()
* qemu_config_write()'s callback config_write_opts()
* main()'s callbacks default_driver_check(), drive_enable_snapshot(),
vnc_init_func()
Drop the parameter, and always stop.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
raw_bsd already has QEMU_BUILD_BUG_ON(BDRV_SECTOR_SIZE != 512), so iscsi
should relax.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When a qcow[2] file is opened, if the header reports an
encryption method, this is used to set the 'crypt_method_header'
field on the BDRVQcow[2]State struct, and the 'encrypted' flag
in the BDRVState struct.
When doing I/O operations, the 'crypt_method' field on the
BDRVQcow[2]State struct is checked to determine if encryption
needs to be applied.
The crypt_method_header value is copied into crypt_method when
the bdrv_set_key() method is called.
The QEMU code which opens a block device is expected to always
do a check
if (bdrv_is_encrypted(bs)) {
bdrv_set_key(bs, ....key...);
}
If code forgets to do this, then 'crypt_method' is never set
and so when I/O is performed, QEMU writes plain text data
into a sector which is expected to contain cipher text, or
when reading, will return cipher text instead of plain
text.
Change the qcow[2] code to consult bs->encrypted when deciding
whether encryption is required, and assert(s->crypt_method)
to protect against cases where the caller forgets to set the
encryption key.
Also put an assert in the set_key methods to protect against
the case where the caller sets an encryption key on a block
device that does not have encryption
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix pointer declaration to make it consistent with the rest of the
code.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function never receives an invalid table pointer, so we can make
it void and remove all the error checking code.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The current cache algorithm traverses the array starting always from
the beginning, so the average number of comparisons needed to perform
a lookup is proportional to the size of the array.
By using a hash of the offset as the starting point, lookups are
faster and independent from the array size.
The hash is computed using the cluster number of the table, multiplied
by 4 to make it perform better when there are collisions.
In my tests, using a cache with 2048 entries, this reduces the average
number of comparisons per lookup from 430 to 2.5.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A cache miss means that the whole array was traversed and the entry
we were looking for was not found, so there's no need to traverse it
again in order to select an entry to replace.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The current algorithm to evict entries from the cache gives always
preference to those in the lowest positions. As the size of the cache
increases, the chances of the later elements of being removed decrease
exponentially.
In a scenario with random I/O and lots of cache misses, entries in
positions 8 and higher are rarely (if ever) evicted. This can be seen
even with the default cache size, but with larger caches the problem
becomes more obvious.
Using an LRU algorithm makes the chances of being removed from the
cache independent from the position.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since all tables are now stored together, it is possible to obtain
the position of a particular table directly from its address, so the
operation becomes O(1).
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The qcow2 L2/refcount cache contains one separate table for each cache
entry. Doing one allocation per table adds unnecessary overhead and it
also requires us to store the address of each table separately.
Since the size of the cache is constant during its lifetime, it's
better to have an array that contains all the tables using one single
allocation.
In my tests measuring freshly created caches with sizes 128MB (L2) and
32MB (refcount) this uses around 10MB of RAM less.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Richard Jones caught this bug with afl fuzzer.
In fact, that's the only possible value to overflow (extent->l1_size =
0x20000000) l1_size:
l1_size = extent->l1_size * sizeof(long) => 0x80000000;
g_try_malloc returns NULL because l1_size is interpreted as negative
during type casting from 'int' to 'gsize', which yields a enormous
value. Hence, by coincidence, we get a "not too bad" behavior:
qemu-img: Could not open '/tmp/afl6.img': Could not open
'/tmp/afl6.img': Cannot allocate memory
Values larger than 0x20000000 will be refused by the validation in
vmdk_add_extent.
Values smaller than 0x20000000 will not overflow l1_size.
Cc: qemu-stable@nongnu.org
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fixes the bug introduced by commit c6ac36e (vmdk: Optimize cluster
allocation).
Sometimes, write_len could be larger than cluster size, because it
contains both data and marker. We must advance next_cluster_sector in
this case, otherwise the image gets corrupted.
Cc: qemu-stable@nongnu.org
Reported-by: Antoni Villalonga <qemu-list@friki.cat>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before a freed cluster can be reused, pending discards for this cluster
must be processed.
The original assumption was that this was not a problem because discards
are only cached during discard/write zeroes operations, which are
synchronous so that no concurrent write requests can cause cluster
allocations.
However, the discard/write zeroes operation itself can allocate a new L2
table (and it has to in order to put zero flags there), so make sure we
can cope with the situation.
This fixes https://bugs.launchpad.net/bugs/1349972.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
A bit of Boolean algebra (and common sense) tells us that the
second "if" here is looking for blocks that are not allocated.
This is the opposite of the "if" that sets BDRV_BLOCK_ALLOCATED,
and thus it can use an "else".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1431599702-10431-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For zero write, callers pass in NULL qiov (qemu-io "write -z" or
scsi-disk "write same").
Commit fc3959e466 fixed bdrv_co_write_zeroes which is the common case
for this bug, but it still exists in bdrv_aio_write_zeroes. A simpler
fix would be in bdrv_co_do_pwritev which is the NULL dereference point
and covers both cases.
So don't access it in bdrv_co_do_pwritev in this case, use three aligned
writes.
[Initialize ret to 0 in bdrv_co_do_zero_pwritev() to avoid uninitialized
variable warning with gcc 4.9.2.
--Stefan]
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1431522721-3266-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit fc3959e466.
The core write code already handles the case, so remove this
duplication.
Because commit 61007b316 moved the touched code from block.c to
block/io.c, the change is manually reverted.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1431522721-3266-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following sequence
int fd = open(argv[1], O_RDWR | O_CREAT | O_DIRECT, 0644);
for (i = 0; i < 100000; i++)
write(fd, buf, 4096);
performs 5% better if buf is aligned to 4096 bytes.
The difference is quite reliable.
On the other hand we do not want at the moment to enforce bounce
buffering if guest request is aligned to 512 bytes.
The patch changes default bounce buffer optimal alignment to
MAX(page size, 4k). 4k is chosen as maximal known sector size on real
HDD.
The justification of the performance improve is quite interesting.
From the kernel point of view each request to the disk was split
by two. This could be seen by blktrace like this:
9,0 11 1 0.000000000 11151 Q WS 312737792 + 1023 [qemu-img]
9,0 11 2 0.000007938 11151 Q WS 312738815 + 8 [qemu-img]
9,0 11 3 0.000030735 11151 Q WS 312738823 + 1016 [qemu-img]
9,0 11 4 0.000032482 11151 Q WS 312739839 + 8 [qemu-img]
9,0 11 5 0.000041379 11151 Q WS 312739847 + 1016 [qemu-img]
9,0 11 6 0.000042818 11151 Q WS 312740863 + 8 [qemu-img]
9,0 11 7 0.000051236 11151 Q WS 312740871 + 1017 [qemu-img]
9,0 5 1 0.169071519 11151 Q WS 312741888 + 1023 [qemu-img]
After the patch the pattern becomes normal:
9,0 6 1 0.000000000 12422 Q WS 314834944 + 1024 [qemu-img]
9,0 6 2 0.000038527 12422 Q WS 314835968 + 1024 [qemu-img]
9,0 6 3 0.000072849 12422 Q WS 314836992 + 1024 [qemu-img]
9,0 6 4 0.000106276 12422 Q WS 314838016 + 1024 [qemu-img]
and the amount of requests sent to disk (could be calculated counting
number of lines in the output of blktrace) is reduced about 2 times.
Both qemu-img and qemu-io are affected while qemu-kvm is not. The guest
does his job well and real requests comes properly aligned (to page).
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1431441056-26198-3-git-send-email-den@openvz.org
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The patch introduces new concept: minimal memory alignment for bounce
buffers. Original so called "optimal" value is actually minimal required
value for aligment. It should be used for validation that the IOVec
is properly aligned and bounce buffer is not required.
Though, from the performance point of view, it would be better if
bounce buffer or IOVec allocated by QEMU will be aligned stricter.
The patch does not change any alignment value yet.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1431441056-26198-2-git-send-email-den@openvz.org
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the behavior in the operating system, for example Linux's
blkdev_write_iter has the following:
if (bdev_read_only(I_BDEV(bd_inode)))
return -EPERM;
This does not apply to opening a device for read/write, when the
device only supports read-only operation. In this case any of
EACCES, EPERM or EROFS is acceptable depending on why writing is
not possible.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1431013548-22492-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Try to perform IO for the biggest continuous block possible.
All blocks abscent in the image are accounted in the same type
and preallocation is made for all of them at once.
The performance for sequential write is increased from 200 Mb/sec to
235 Mb/sec on my SSD HDD.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-28-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Plain image expansion spends a lot of time to update image file size.
This seriously affects the performance. The following simple test
qemu_img create -f parallels -o cluster_size=64k ./1.hds 64G
qemu_io -n -c "write -P 0x11 0 1024M" ./1.hds
could be improved if the format driver will pre-allocate some space
in the image file with a reasonable chunk.
This patch preallocates 128 Mb using bdrv_write_zeroes, which should
normally use fallocate() call inside. Fallback to older truncate()
could be used as a fallback using image open options thanks to the
previous patch.
The benefit is around 15%.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Karan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-27-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is preparational commit for tweaks in Parallels image expansion.
The idea is that enlarge via truncate by one data block is slow. It
would be much better to use fallocate via bdrv_write_zeroes and
expand by some significant amount at once.
Original idea with sequential file writing to the end of the file without
fallocate/truncate would be slower than this approach if the image is
expanded with several operations:
- each image expanding means file metadata update, i.e. filesystem
journal write. Truncate/write to newly truncated space update file
metadata twice thus truncate removal helps. With fallocate call
inside bdrv_write_zeroes file metadata is updated only once and
this should happen infrequently thus this approach is the best one
for the image expansion
- tail writes are ordered, i.e. the guest IO queue could not be sent
immediately to the host introducing additional IO delays
This patch just adds proper parameters into BDRVParallelsState and
performs options parsing in parallels_open.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-26-git-send-email-den@openvz.org
CC: Roman Kagan <rkagan@parallels.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The idea is that we do not need to immediately sync BAT to the image as
from the guest point of view there is a possibility that IO is lost
even in the physical controller until flush command was finished.
bdrv_co_flush_to_os is exactly the right place for this purpose.
Technically the patch uses loaded BAT data as a cache and performs
actual on-disk metadata updates in parallels_co_flush_to_os callback.
This patch speed ups
qemu-img create -f parallels -o cluster_size=64k ./1.hds 64G
qemu-io -f parallels -c "write -P 0x11 0 1024k" 1.hds
writing from 50-60 Mb/sec to 80-90 Mb/sec on rotational media and
from 160 Mb/sec to 190 Mb/sec on SSD disk.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-25-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
calculate offset of the BAT entry in the image file.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-24-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Try to perform IO for the biggest continuous block possible.
The performance for sequential read is increased from 220 Mb/sec to
360 Mb/sec for continous image on my SSD HDD.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-23-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The software driver must set inuse field in Parallels header to
0x746F6E59 when the image is opened in read-write mode. The presence of
this magic in the header on open forces image consistency check.
There is an unfortunate trick here. We can not check for inuse in
parallels_check as this will happen too late. It is possible to do
that for simple check, but during the fix this would always report
an error as the image was opened in BDRV_O_RDWR mode. Thus we save
the flag in BDRVParallelsState for this.
On the other hand, nothing should be done to clear inuse in
parallels_check. Generic close will do the job right.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-21-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The check is very simple at the moment. It calculates necessary stats
and fix only the following errors:
- space leak at the end of the image. This would happens due to
preallocation
- clusters outside the image are zeroed. Nothing else could be done here
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-20-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will help to avoid forward declarations for upcoming parallels_check
Some very obvious formatting fixes were made to the moved code to make
checkpatch happy.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-19-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This metadata cache would allow to properly batch BAT updates to disk
in next patches. These updates will be properly aligned to avoid
read-modify-write transactions on block level.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-18-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will allow to use this data as buffer to BAT update directly
without any intermediate buffers.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-17-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
deduplicate copy/paste arithmetcs
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-16-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
BAT means 'block allocation table'. Thus this name is clean and shorter
on writing.
Some obvious formatting fixes in the old code were made to make checkpatch
happy.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-15-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-14-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Do not even care to create WithoutFreeSpace image, it is obsolete.
Always create WithouFreSpacExt one.
The code also does not spend a lot of efforts to fill cylinders and
heads fields, they are not used actually in a real life neither in
QEMU nor in Parallels products.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-12-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Support write on Parallels images. The code is almost the same as one
in the previous patch implemented scatter-gather IO for read.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-10-git-send-email-den@openvz.org
CC: Roman Kagan <rkagan@parallels.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
From the guest point of view unallocated blocks are zeroed.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-9-git-send-email-den@openvz.org
CC: Roman Kagan <rkagan@parallels.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
simple purification..
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-8-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Main approach is taken from qcow2_co_readv.
The patch drops coroutine lock for the duration of IO operation and
peforms normal scatter-gather IO using standard QEMU backend.
The patch also adds comment about locking considerations in the driver.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Message-id: 1430207220-24458-7-git-send-email-den@openvz.org
CC: Roman Kagan <rkagan@parallels.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Implement VFS method for get_block_status to Parallels format driver.
qemu_co_mutex_lock is not necessary yet (the driver is read-only) but
will be necessary very soon when write will be supported.
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-id: 1430207220-24458-6-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Teach parallels_read() to do reads in coarser granularity than just a
single sector: if requested, read up to the cluster end in one go.
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1430207220-24458-5-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Switch the .bdrv_read method implementation from using bdrv_pread() to
bdrv_read() on the underlying file, since the latter is subject to i/o
throttling while the former is not.
Besides, since bdrv_read() operates in sectors rather than bytes, adjust
the helper functions to do so too.
Signed-off-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-id: 1430207220-24458-4-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
this follows QEMU coding convention
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@parallels.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1430207220-24458-3-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
QTYPE_NONE is a sentinel value. No QObject has this type code.
Document it properly.
Fix dump_qobject() to abort() on QTYPE_NONE, just like for any other
invalid type code.
Fix to_json() to abort() on all invalid type codes, not just
QTYPE_MAX.
Clean up Property member qtype's type: it's a qtype_code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The block.c file has grown to over 6000 lines. It is time to split this
file so there are fewer conflicts and the code is easier to maintain.
Extract I/O request processing code:
* Read
* Write
* Zero writes and making the image empty
* Flush
* Discard
* ioctl
* Tracked requests and queuing
* Throttling and copy-on-read
* Block status and allocated functions
* Refreshing block limits
* Reading/writing vmstate
* qemu_blockalign() and friends
The patch simply moves code from block.c into block/io.c.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Coverity spotted this.
The field is 32 bits, but if it's possible to overflow in 32 bit
left shift.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
dmg can optionally utilize libbz2, make it modular
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The mirror block job is trying to take a clever shortcut if delay_ns is
0 and skips block_job_sleep_ns() in that case. But that function must be
called in every block job iteration, because otherwise it is for example
impossible to pause the job.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We often don't need the BlockDriverState for functions
that operate on bitmaps. Remove it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For "dirty-bitmap" sync mode, the block job will iterate through the
given dirty bitmap to decide if a sector needs backup (backup all the
dirty clusters and skip clean ones), just as allocation conditions of
"top" sync mode.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-11-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The new command pair is added to manage a user created dirty bitmap. The
dirty bitmap's name is mandatory and must be unique for the same device,
but different devices can have bitmaps with the same names.
The granularity is an optional field. If it is not specified, we will
choose a default granularity based on the cluster size if available,
clamped to between 4K and 64K to mirror how the 'mirror' code was
already choosing granularity. If we do not have cluster size info
available, we choose 64K. This code has been factored out into a helper
shared with block/mirror.
This patch also introduces the 'block_dirty_bitmap_lookup' helper,
which takes a device name and a dirty bitmap name and validates the
lookup, returning NULL and setting errp if there is a problem with
either field. This helper will be re-used in future patches in this
series.
The types added to block-core.json will be re-used in future patches
in this series, see:
'qapi: Add transaction support to block-dirty-bitmap-{add, enable, disable}'
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1429314609-29776-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We treat this field with a variety of different types everywhere
in the code. Now it's just uint32_t.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field will be set for user created dirty bitmap. Also pass in an
error pointer to bdrv_create_dirty_bitmap, so when a name is already
taken on this BDS, it can report an error message. This is not global
check, two BDSes can have dirty bitmap with a common name.
Implemented bdrv_find_dirty_bitmap to find a dirty bitmap by name, will
be used later when other QMP commands want to reference dirty bitmap by
name.
Add bdrv_dirty_bitmap_make_anon. This unsets the name of dirty bitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
the allocationmap has only a hint character. The driver always
double checks that blocks marked unallocated in the cache are
still unallocated before taking the fast path and return zeroes.
So using the allocationmap is migration safe and can
also be enabled with cache.direct=on.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-10-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-9-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
a target may issue a SCSI_STATUS_TASK_SET_FULL status
if there is more than one "BUSY" command queued already.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-8-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The idea is that a command is retried in a BUSY condition
up a time of approx. 60 seconds before it is failed. This should
be far higher than any command timeout in the guest.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-7-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI allowes to tell the target to not return from a write command
if the date is not written to the disk. Use this so called FUA
bit if it is supported to optimize WRITE commands if writeback is
not allowed.
In this case qemu always issues a WRITE followed by a FLUSH. This
is 2 round trip times. If we set the FUA bit we can ignore the
following FLUSH.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-6-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-5-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-4-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-3-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We actually were always impolitely dropping the connection and
not cleanly logging out.
CC: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1429193313-4263-2-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The image field in BlockDeviceInfo is supposed to contain an ImageInfo
object. However that is being filled in by bdrv_query_info(), not by
bdrv_block_device_info(), which is where BlockDeviceInfo is actually
created.
Anyone calling bdrv_block_device_info() directly will get a null image
field. As a consequence of this, the HMP command 'info block -n -v'
crashes QEMU.
This patch moves the code that fills in that field from
bdrv_query_info() to bdrv_block_device_info().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 1429271563-3765-1-git-send-email-berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since this event can occur in nodes that cannot have a device name
associated, include also a field with the node name.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 147cec5b3594f4bec0cb41c98afe5fcbfb67567c.1428485266.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are several error messages that identify a BlockDriverState by
its device name. However those errors can be produced in nodes that
don't have a device name associated.
In those cases we should use bdrv_get_device_or_node_name() to fall
back to the node name and produce a more meaningful message. The
messages are also updated to use the more generic term 'node' instead
of 'device'.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 9823a1f0514fdb0692e92868661c38a9e00a12d6.1428485266.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function gets the device name associated with a BlockDriverState,
or its node name if the device name is empty.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 4fa30aa8d61d9052ce266fd5429a59a14e941255.1428485266.git.berto@igalia.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1428069921-2957-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch changes block_job_pause to increase the pause counter and
block_job_resume to decrease it.
The counter will allow calling block_job_pause/block_job_resume
unconditionally on a job when we need to suspend the IO temporarily.
From now on, each block_job_resume must be paired with a block_job_pause
to keep the counter balanced.
The user pause from QMP or HMP will only trigger block_job_pause once
until it's resumed, this is achieved by adding a user_paused flag in
BlockJob.
One occurrence of block_job_resume in mirror_complete is replaced with
block_job_enter which does what is necessary.
In block_job_cancel, the cancel flag is good enough to instruct
coroutines to quit loop, so use block_job_enter to replace the unpaired
block_job_resume.
Upon block job IO error, user is notified about the entering to the
pause state, so this pause belongs to user pause, set the flag
accordingly and expect a matching QMP resume.
[Extended doc comments as suggested by Paolo Bonzini
<pbonzini@redhat.com>.
--Stefan]
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1428069921-2957-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reopen is used in block-commit. With this always-succeed operation, it
is now possible to test committing to a null drive, by specifying
"null-aio://" or "null-co://" as the backing image when creating the
qcow2 image.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427852740-24315-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Aio context switch should just work because the requests will be
drained, so the scheduled timer(s) on the old context will be freed.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427852740-24315-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix the length of the zero-fill for the back, which was accidentally
using the same value as for the front. This is caught by qemu-iotests
033.
For consistency, change the code for the front as well to use the length
stored in the iov (it is the same value, copied four lines above).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Jeff Cody <jcody@redhat.com>
This is, amongst others, required for qemu-iotests 033 to run as
intended on VHDX, which uses explicit bdrv_truncate() calls to bs->file
when allocating new blocks.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
This commit was generated mechanically by coccinelle from the following
semantic patch:
@@
expression val;
@@
- (ffs(val) - 1)
+ ctz32(val)
The call sites have been audited to ensure the ffs(0) - 1 == -1 case
never occurs (due to input validation, asserts, etc). Therefore we
don't need to worry about the fact that ctz32(0) == 32.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-5-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The command "virsh create" will fail in such condition: vm has two
disks: vda and vdb. vda has snapshot s1 with id "1", vdb doesn't have
s1 but has snapshot s2 with id "1". When we want to run command "virsh
create s1", del_existing_snapshots() only deletes s1 in vda, and
bdrv_snapshot_create() tries to create vdb's snapshot s1 with id "1",
but id "1" alreay exists in vdb with name "s2"!
The simplest way is call find_new_snapshot_id() unconditionally.
Signed-off-by: Yi Wang <up2wing@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
newer libiscsi versions may return zero events from iscsi_which_events.
In this case iscsi_service will return immediately without any progress.
To avoid busy waiting for iscsi_which_events to change we deregister all
read and write handlers in this case and schedule a timer to periodically
check iscsi_which_events for changed events.
Next libiscsi version will introduce async reconnects and zero events
are returned while libiscsi is waiting for a reconnect retry.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1428437295-29577-1-git-send-email-pl@kamp.de
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In recent qemu versions, it is possible to override the backing file
name and format that is stored in the image file with values given at
runtime. In such cases, the temporary override could end up in the
image header if the qcow2 header was updated, while obviously correct
behaviour would be to leave the on-disk backing file path/format
unchanged.
Fix this and add a test case for it.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1428411796-2852-1-git-send-email-kwolf@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, if the user requests aio=native, but forgets to choose a
cache mode that sets O_DIRECT, that request is silently ignored and raw
falls back to aio=threads.
Deprecate that behaviour so we can make it an error in future qemu
versions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Raise your hand if you have a physical floppy drive in a computer
you've powered on in 2015. Okay, I see we got a few weirdos in the
audience. That's okay, weirdos are welcome here.
Kidding aside, media change detection doesn't fully work, isn't going
to be fixed, and floppy passthrough just isn't earning its keep
anymore.
Deprecate block driver host_floppy now, so we can drop it after a
grace period.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sparse reports this warning:
block/qapi.c:417:47: warning:
too long initializer-string for array of char(no space for nul char)
Replacing the string by an array of characters fixes this warning.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <1424887718-10800-13-git-send-email-mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
unix_connect_opts() and inet_connect_opts() do not necessarily set errno
(if at all); therefore, nbd_establish_connection() should not literally
return -errno on error.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <1424887718-10800-4-git-send-email-mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The code to check the bitmap for the allocation status of each sector
has been "disabled by reason" ever since the vpc driver existed.
The reason might be that we might end up reading sector by sector
in vpc_read if we really used it. This would be a performance desaster.
The current code would furthermore not work if the disabled parts get
reactivated since vpc_read and vpc_write only use get_sector_offset to
check the allocation status of the first sector of a read/write operation.
This might lead to sectors incorrectly treated as zero in vpc_read and
to sectors getting allocated twice in vpc_write.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1425379316-19639-6-git-send-email-pl@kamp.de
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
the field is named current size in the spec. Name it accordingly.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1425379316-19639-5-git-send-email-pl@kamp.de
Signed-off-by: Max Reitz <mreitz@redhat.com>
The VHD spec [1] allows for total_sectors of 65535 x 16 x 255 (~127GB)
represented by a CHS geometry. If total_sectors is greater
than 65535 x 16 x 255 this geometry is set as a maximum.
Qemu, Hyper-V and disk2vhd use this special geometry as an indicator
to use the image current size from the footer as disk size.
This patch changes vpc_create to effectively calculate a CxHxS geometry
for the given image size if possible while rounding up if necessary.
If the image size is too big to be represented in CHS we set the maximum
and write the exact requested image size into the footer.
This partly reverts commit 258d2edb, but leaves support for >127G disks
intact.
[1] http://download.microsoft.com/download/f/f/e/ffef50a5-07dd-4cf8-aaa3-442c0673a029/Virtual%20Hard%20Disk%20Format%20Spec_10_18_06.doc
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1425379316-19639-4-git-send-email-pl@kamp.de
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The CHS calculation as done per the VHD spec imposes a maximum image
size of ~127 GB. Real VHD images exist that are larger than that.
Apparently there are two separate non-standard ways to achieve this:
You could use more heads than the spec does - this is the option that
qemu-img create chooses.
However, other images exist where the geometry is set to the maximum
(65535/16/255), but the actual image size is larger. Until now, such
images are truncated at 127 GB when opening them with qemu.
This patch changes the vpc driver to ignore geometry in this case and
only trust the size field in the header.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
[PL: Fixed maximum geometry in the commit msg]
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1425379316-19639-3-git-send-email-pl@kamp.de
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
*pnum can't be greater than s->block_size / BDRV_SECTOR_SIZE for allocated
sectors since there is always a bitmap in between.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1425379316-19639-2-git-send-email-pl@kamp.de
Signed-off-by: Max Reitz <mreitz@redhat.com>
When choosing a new place for the refcount table, alloc_refcount_block()
tries to infer the number of clusters used so far from its argument
cluster_index (which comes from the idea that if any cluster with an
index greater than cluster_index was in use, the refcount table would
have to be big enough already to describe cluster_index).
However, there is a cluster that may be at or after cluster_index, and
which is not covered by the refcount structures, and that is the new
refcount block new_block. Therefore, it should be taken into account for
the blocks_used calculation.
Also, because new_block already describes (or is intended to describe)
cluster_index, we may not put the new refcount structures there.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 1423598552-24301-2-git-send-email-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Error classes are a leftover from the days of "rich" error objects.
New code should always use ERROR_CLASS_GENERIC_ERROR. Commit e246211
added a use of ERROR_CLASS_DEVICE_NOT_FOUND. Replace it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
QCOW_MAX_L1_SIZE's unit is byte, and l1_size's unit
is l1 table entry size(8 bytes).
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Message-id: 54FFB0F1.5010307@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Coverity/sparse fix for iscsi driver
- RCU fallout: fix -daemonize and s390x system emulation
- KVM: kvm_stat improvements and new man page
- x86: SYSRET fix for VxWorks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU/sUFAAoJEL/70l94x66D1JwIAJ28Lan2DQwi+xHvNxF8zW6n
v7eMc04/fepuon0TYmUZC3qbqc00sccEQZQ+yAAauT9epZ/kdSDudDOzG+3F4MuQ
/X3crXw2/jrhtWedGq49vFCONX4MKoaoudqK8kOFMe1ImQgkOYeAzOoqeFXyHsFh
jINlKTJZB6oKzrZ+SYryY14cO7pvGaIhyqaCC+6GcVihTjm9Yq13lP1lFj7LsVRV
aGfd6xH9RSV/mwzvZwD4i3cUWSUaV/wY0NDhAEzDPCUcxX0/nAj3XF1YeJUF30Qd
ETaCLo/Nxq2R6POK3c/Zm/FRLvjzZ2caD+q1LcwB/bCYdc2lJ1JDxE/hr48ANv0=
=OWXY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- scsi: improvements to error reporting and conversion to realize,
Coverity/sparse fix for iscsi driver
- RCU fallout: fix -daemonize and s390x system emulation
- KVM: kvm_stat improvements and new man page
- x86: SYSRET fix for VxWorks
# gpg: Signature made Tue Mar 10 10:18:45 2015 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
x86: fix SS selector in SYSRET
scsi: Convert remaining PCI HBAs to realize()
scsi: Improve error reporting for invalid drive property
hw: Propagate errors through qdev_prop_set_drive()
scsi: Clean up duplicated error in legacy if=scsi code
cpus: initialize cpu->memory_dispatch
rcu: handle forks safely
qemu-thread: do not use PTHREAD_MUTEX_ERRORCHECK
kvm_stat: add kvm_stat.1 man page
kvm_stat: add column headers to text UI
iscsi: Fix check for username
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hlbC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block patches for 2.3
# gpg: Signature made Tue Mar 10 13:03:17 2015 GMT using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (73 commits)
MAINTAINERS: Add jcody as blockjobs, block devices maintainer
iotests: add O_DIRECT alignment probing test
block/raw-posix: fix launching with failed disks
MAINTAINERS: Add jsnow as IDE maintainer
sheepdog: Fix misleading error messages in sd_snapshot_create()
Add testcase for scsi-hd devices without drive property
scsi-hd: fix property unset case
block/vdi: Add locking for parallel requests
iotests: Drop vpc from 004's and 104's format list
iotests: Remove 006
iotests: Fix 051's reference output
virtio-blk: Remove the stale FIXME comment
tests: Check QVIRTIO_F_ANY_LAYOUT flag in virtio-blk test
libqos: Solve bug in interrupt checking when using MSIX in virtio-pci.c
sheepdog: fix confused return values
qtest/ahci: add fragmented dma test
qtest/ahci: Add PIO and LBA48 tests
qtest/ahci: Add DMA test variants
libqos/ahci: add ahci command helpers
qtest/ahci: Add a macro bootup routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit c25f53b06e ("raw: Probe
required direct I/O alignment") QEMU has failed to launch if image files
produce I/O errors.
Previously, QEMU would launch successfully and the guest would see the
errors when attempting I/O.
This is a regression and may prevent multipath I/O inside the guest,
where QEMU must launch and let the guest figure out by itself which
disks are online.
Tweak the alignment probing code in raw-posix.c to explicitly look for
EINVAL on Linux instead of bailing. The kernel refuses misaligned
requests with this error code and other error codes can be ignored.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If do_sd_create() fails, it first reports the error returned, then
reports a another one with strerror(errno). errno is meaningless at
that point.
Report just one error combining the valid information from both
messages.
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Liu Yuan <namei.unix@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When allocating a new cluster, the first write to it must be the one
doing the allocation, because that one pads its write request to the
cluster size; if another write to that cluster is executed before it,
that write will be overwritten due to the padding.
See https://bugs.launchpad.net/qemu/+bug/1422307 for what can go wrong
without this patch.
Cc: qemu-stable <qemu-stable@nongnu.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These functions mix up -1 and -errno in return values and would might cause
trouble error handling in the call chain.
This patch let them return -errno and add some comments.
Cc: qemu-devel@nongnu.org
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Liu Yuan <liuyuan@cmss.chinamobile.com>
Message-id: 1424231875-7131-1-git-send-email-namei.unix@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1424087278-49393-5-git-send-email-tumanova@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduce driver methods of defining disk blocksizes (physical and
logical) and hard drive geometry.
Methods are only implemented for "host_device". For "raw" devices
driver calls child's method.
For now geometry detection will only work for DASD devices. To check
that a local check_for_dasd function was introduced. It calls BIODASDINFO2
ioctl and returns its rc.
Blocksizes detection function will probe sizes for DASD devices.
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1424087278-49393-4-git-send-email-tumanova@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Put it in new probe_logical_blocksize().
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1424087278-49393-3-git-send-email-tumanova@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Background:
The blkdebug scripts are currently engineered so that when a debug
event occurs, a prefilter browses a master list of parsed rules for a
certain event and adds them to an "active list" of rules to be used for
the forthcoming action, provided the events and state numbers match.
Then, once the request is received, the last active rule is used to
inject an error if certain parameters match.
This active list is cleared every time the prefilter injects a new
rule for the first time during a debug event.
The "once" rule currently causes the error injection, if it is
triggered, to only clear the active list. This is insufficient for
preventing future injections of the same rule.
Remedy:
This patch /deletes/ the rule from the list that the prefilter
browses, so it is gone for good. In V2, we remove only the rule of
interest from the active list instead of allowing the "once" rule to
clear the entire list of active rules.
Impact:
This affects iotests 026. Several ENOSPC tests that used "once" can
be seen to have output that shows multiple failure messages. After
this patch, the error messages tend to be smaller and less severe, but
the injection can still be seen to be working. I have patched the
expected output to expect the smaller error messages.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1423257977-25630-1-git-send-email-jsnow@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a creation option to qcow2 for setting the refcount order of images
to be created, and respect that option's value.
This breaks some test outputs, fix them.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2_amend_options() should not compare options against some inline
strings but rather use the symbolic macros available for each of the
creation options.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a refcount_order parameter to qcow2_create2(), use that value for
the image header and for calculating the size required for
preallocation.
For now, always pass 4.
This addition requires changes to the calculation of the file size for
the "full" and "falloc" preallocation modes. That in turn is a nice
opportunity to add a comment about that calculation not necessarily
being exact (and that being intentional).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
No longer refuse to open images with a different refcount entry width
than 16 bits; only reject images with a refcount width larger than 64
bits (which is prohibited by the specification).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add helper functions for getting and setting refcounts in a refcount
array for any possible refcount order, and choose the correct one during
refcount initialization.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since refcounts do not always have to be a uint16_t, all refcount blocks
and arrays in memory should not have a specific type (thus they become
pointers to void) and for accessing them, two helper functions are used
(a getter and a setter). Those functions are called indirectly through
function pointers in the BDRVQcowState so they may later be exchanged
for different refcount orders.
With the check and repair functions using this function, the refcount
array they are creating will be in big endian byte order; additionally,
using realloc_refcount_array() makes the size of this refcount array
always cluster-aligned. Both combined allow rebuild_refcount_structure()
to drop the bounce buffer which was used to convert parts of the
refcount array to big endian byte order and store them on disk. Instead,
those parts can now be written directly.
[ kwolf: Fixed a build failure on 32 bit and another with old glib ]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a helper function for reallocating a refcount array, independent of
the refcount order. The newly allocated space is zeroed and the function
handles failed reallocations gracefully.
The helper function will always align the buffer size to a cluster
boundary; if storing the refcounts in such an array in big endian byte
order, this makes it possible to write parts of the array directly as
refcount blocks into the image file.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Refcounts may have a width of up to 64 bits, so qemu should use the same
width to represent refcount values internally.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
update_refcount() and qcow2_update_cluster_refcount() currently take a
signed addend. At least one caller passes a value directly derived from
an absolute refcount that should be reached ("l2_refcount - 1" in
expand_zero_clusters_in_l1()). Therefore, the addend should be unsigned
as well; this will be especially important for 64 bit refcounts.
Because update_refcount() then no longer knows whether the refcount
should be increased or decreased, it now requires an additional flag
which specified exactly that. The same applies to
qcow2_update_cluster_refcount().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Refcounts can theoretically be of type uint64_t; in order to be able to
represent the full range, qcow2_get_refcount() cannot use a single
variable to represent both all refcount values and also keep some values
reserved for errors.
One solution would be to add an Error pointer parameter to
qcow2_get_refcount(); however, no caller could (currently) pass that
error message, so it would have to be emitted immediately and be
passed to the next caller by returning -EIO or something similar.
Therefore, an Error parameter does not offer any advantages here.
The solution applied by this patch is simpler to use. Because no caller
would be able to pass the error message, they would have to print it and
free it, whereas with this patch the caller only needs to pass the
returned integer (which is often a no-op from the code perspective,
because that integer will be stored in a variable "ret" which will be
returned by the fail path of many callers).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2_update_cluster_refcount() does not have any quick access to the
new refcount value, it has to call qcow2_get_refcount(). Some callers do
not need that new value at all, others call qcow2_get_refcount()
themselves anyway (albeit in a different code path, which can however be
easily changed), therefore there is no advantage in making
qcow2_update_cluster_refcount() return the new value. Drop it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add the bit width of every refcount entry to the format-specific
information.
In contrast to lazy_refcounts and the corrupt flag, this should be
always emitted, even for compat=0.10 although it does not support any
refcount width other than 16 bits. This is because if a boolean is
optional, one normally assumes it to be false when omitted; but if an
integer is not specified, it is rather difficult to guess its value.
This new field breaks some test outputs, fix them.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add two new fields regarding refcount information (the bit width of
every entry and the maximum refcount value) to the BDRVQcowState.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The variable user in struct iscsi_url is a character array, not a pointer.
Therefore its address will never be NULL.
clang reports this error:
block/iscsi.c:1329:20: warning:
comparison of array 'iscsi_url->user' not equal to a null pointer
is always true [-Wtautological-pointer-compare]
Reviewed-by: Peter Lieven <pl@kamp.de>
Acked-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <1425719670-5486-1-git-send-email-sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only user went away five years ago with commit a9420734 ('qcow2:
Simplify image creation'). It's about time to remove it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
block/raw-posix.c:947:19: warning: unused variable 's' [-Wunused-variable]
BDRVRawState *s = aiocb->bs->opaque;
This variable is used only when on of the following macros are defined
CONFIG_XFS, CONFIG_FALLOCATE, CONFIG_FALLOCATE_PUNCH_HOLE or
CONFIG_FALLOCATE_ZERO_RANGE. Fortunately, CONFIG_FALLOCATE_PUNCH_HOLE
and CONFIG_FALLOCATE_ZERO_RANGE could be defined only along with
CONFIG_FALLOCATE. Therefore checking for CONFIG_XFS or CONFIG_FALLOCATE
would be enough.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Previously, qemu block driver of sheepdog used hard-coded VDI object size.
This patch enables users to handle VDI object size.
When you start qemu, you don't need to specify additional command option.
But when you create the VDI which doesn't have default object size
with qemu-img command, you specify object_size option.
If you want to create a VDI of 8MB object size,
you need to specify following command option.
# qemu-img create -o object_size=8M sheepdog:test1 100M
In addition, when you don't specify qemu-img command option,
a default value of sheepdog cluster is used for creating VDI.
# qemu-img create sheepdog:test2 100M
Signed-off-by: Teruaki Ishizaki <ishizaki.teruaki@lab.ntt.co.jp>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This implements bdrv_co_get_block_status() for VHD images. This can
significantly speed up qemu-img convert operation because only with this
function implemented sparseness can be considered. (Before, converting a
1 TB empty image took several minutes for me, now it's instantaneous.)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
If total_sectors is rounded to match the geometry, total_size needs to
be changed as well. Otherwise we end up with an image whose geometry
describes a disk larger than the image file, which doesn't end well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
