Handle the virtio-ccw revision according to what the guest sets.
When revision 1 is selected, we have a virtio-1 standard device
with byteswapping for the virtio rings.
When a channel gets disabled, we have to revert to the legacy behavior
in case the next user of the device does not negotiate the revision 1
anymore (e.g. the boot firmware uses revision 1, but the operating
system only uses the legacy mode).
Note that revisions > 0 are still disabled.
[CH: assure memory accesses are always BE]
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
We need a possibility to run code when a subchannel gets disabled.
This patch adds the necessary infrastructure.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Our main channel_subsys structure is not a device (yet), but we need
to setup mss/mcss-e again if the guest had enabled it before. Use
a hack that should catch most configurations (assuming that the guest
will have enabled at least one device in higher subchannel sets or
channel subsystems if it enabled the functionality.)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
For a guest-initiated reset, we need to not only reset the virtio device,
but also reset the VirtioCcwDevice into a clean state. This includes
resetting the indicators, or else a guest will not be able to e.g.
switch from classic interrupts to adapter interrupts.
Split off this routine into a new function virtio_ccw_reset_virtio()
to make the distinction between resetting the virtio-related devices
and the base subchannel device clear.
CC: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Almost exclusively bugfixes, though in this case,
we are adding functionality to the pxb in order
to make OVMF work on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVjVb/AAoJECgfDbjSjVRpeaEH/2bwK7BGgczEQ7fhzIEaQSQq
SV7aychNZvUFASXLV6aVmQCdYixZxlI9KDn0pMRYntUcjxRRB48U3N5Sy4km46Pw
LLN3vxGzHazlE7AJ5c+WVDf0e2k7v3CpZ/TKXzPHmvZXIuBfjKXtKzBgyQYxGkmL
JgRrRSHDrsbvfmhI4uHMpCTYs/WeY1cuA1IzvimBjmvVP5kkko4NoX+HEWmGJ6WK
13fQuV+Cvz7Yk40HRpPAM0QPV2etGCj+dU7xgF9BWnn9mzbGC5iy8EUClyGil/af
k3i/bCxs6IgpQ76LaezJtGPtn1jbohrO4qRqlatUAJCwgCYMCkxkIk+Pr4A3x4c=
=6WvB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci fixes, enhancements
Almost exclusively bugfixes, though in this case,
we are adding functionality to the pxb in order
to make OVMF work on it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri Jun 26 14:43:27 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
Fix glib_subprocess test
hw/pci-bridge: format special OFW unit address for PXB host
hw/core: explicit OFW unit address callback for SysBusDeviceClass
hw/pci-bridge: disable SHPC in PXB
hw/pci-bridge: introduce "shpc" property
hw/pci: introduce shpc_present() helper function
hw/pci-bridge: add macro for "msi" property
hw/pci-bridge: add macro for "chassis_nr" property
hw/pci-bridge: expose _test parameter in SHPC_VMSTATE()
migration: introduce VMSTATE_BUFFER_UNSAFE_INFO_TEST()
add pci-bridge-seat
pc: cleanup and convert TMP ACPI device description to AML API
MAINTAINERS: add ACPI entry
vhost: correctly pass error to caller in vhost_dev_enable_notifiers()
balloon: add a feature bit to let Guest OS deflate balloon on oom
qdev: fix OVERFLOW_BEFORE_WIDEN
virito-pci: fix OVERRUN problem
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have virtio-pci, we can make the virt board's default block
device type be IF_VIRTIO. This allows users to use simplified
command lines that don't have to explicitly create virtio-pci-blk
devices; the -hda &c very short options now also work.
This means we also need to set no_cdrom to avoid getting a
default cdrom device -- this is needed because the virtio-blk
device will fail if it is connected to a block backend with
no media, which is what the default cdrom device typically is.
Providing a cdrom with media via -cdrom will succeed, but silently
create a device with non-removable medium. this is probably
not really what the user wants, but is the best we can do now.
Note that this change means that some command lines which used
to work (by accident) will stop working. Where a drive was connected
manually to a device but without 'if=none' being specified, we
used to treat this as an IDE drive, which we would then not autoplug
because the board doesn't support IDE. Now we will treat it as a
virtio disk and autoplug it, which means the attempt to use the
drive manually will fail:
qemu-system-arm: -drive file=img.qcow2,id=foo: Drive 'foo' is already
in use because it has been automatically connected to another device
(did you need 'if=none' in the drive options?)
The command line will have to be changed to include 'if=none', as the
error message suggests.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435068107-12594-4-git-send-email-peter.maydell@linaro.org
If the user forgot if=none on their drive specification they're likely
to get an error message because the drive is assigned once automatically
by QEMU and once by the manual id=/drive= user command line specification.
Improve the error message produced in this case to explicitly guide the
user towards if=none.
We rephrase the "drive conflict but not for an if=something" error as
well to keep the wording in line.
The two cases that change are:
(1) Drive specified as to be auto-connected and also manually connected
(and the board does handle this if= type):
qemu-system-x86_64 -nodefaults -display none \
-drive if=scsi,file=tmp.qcow2,id=foo -device ide-hd,drive=foo
Previously:
qemu-system-x86_64: -device ide-hd,drive=foo: Property 'ide-hd.drive'
can't take value 'foo', it's in use
Now:
qemu-system-x86_64: -device ide-hd,drive=foo: Drive 'foo' is already in
use because it has been automatically connected to another device (did
you need 'if=none' in the drive options?)
(2) Drive specified to be manually connected in two different ways:
qemu-system-x86_64 -nodefaults -display none \
-drive if=none,file=tmp.qcow2,id=foo -device ide-hd,drive=foo \
-device ide-hd,drive=foo
Previously:
qemu-system-x86_64: -device ide-hd,drive=foo: Property 'ide-hd.drive'
can't take value 'foo', it's in use
Now:
qemu-system-x86_64: -device ide-hd,drive=foo: Drive 'foo' is already in
use by another device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435068107-12594-3-git-send-email-peter.maydell@linaro.org
Instead of having set_pointer() call a parse callback which returns
an error number that we then convert to an Error string with
error_set_from_qdev_prop_error(), make the parse callback take an
Error** and set the error itself. This will allow parse routines
to provide more helpful error messages than the generic ones.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435068107-12594-2-git-send-email-peter.maydell@linaro.org
Add GICv2m description in ACPI MADT table, so guest can use MSI when
booting with ACPI.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Message-id: 1434676210-2276-1-git-send-email-shannon.zhao@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The table revision is not the ACPI spec version. Fix the wrong revision
and also some comments.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1433820378-8336-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add UHI semihosting support for MIPS. QEMU run with "-semihosting" option
will alter the behaviour of SDBBP 1 instruction -- UHI operation will be
called instead of generating a debug exception.
Also tweak Malta's pseudo-bootloader. On CPU reset the $4 register is set
to -1 if semihosting arguments are passed to indicate that the UHI
operations should be used to obtain input arguments.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
The BEV flag controls whether the boot exception vector is still
in place when starting a kernel. When cleared the exception vector
at EBASE (or hard coded address of 0x80000000) is used instead.
The early stages of the linux kernel would benefit from BEV still
being set to ensure any faults get handled by the boot rom exception
handlers. This is a moot point for system qemu as there aren't really
any BEV handlers, but there are other good reasons to change this...
The UHI (semi-hosting interface) defines special behaviours depending
on whether an application starts in an environment with BEV set or
cleared. When BEV is set then UHI assumes that a bootloader is
relatively dumb and has no advanced exception handling logic.
However, when BEV is cleared then UHI assumes that the bootloader
has the ability to handle UHI exceptions with its exception handlers
and will unwind and forward UHI SYSCALL exceptions to the exception
vector that was installed prior to running the application.
Signed-off-by: Matthew Fortune <matthew.fortune@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Version: GnuPG v1
iQEcBAABAgAGBQJVisx5AAoJEJykq7OBq3PIbasIALJC/7BEyCSEubcjH25CIzao
D20ufmo8/Et6KGuD1r2zdGRXQ79q/SDCGStQK8QEEfvRxPMehngfCUb5aJXkcGbu
/bRIaHh7DFxSiPGJI1/1wwR1MC7tjjR6ZrpSd2OTF0VOZvuXlP3noWpX1eiRAcvu
ekK2vvYtDi03/Xzhbx8MIRSuYPAdh/tXZ3mrDfUQNrtO47QYAxh0C9ABzZVrHJCa
RFCFXPoqZroOcrVe20ZHLt82AUL0H3cfHvF74Z+LbOlPJ7JbP/5+PzLisAqX7VeE
VYvK78mQih41Ww+qYYx4lwhUMUW1fYYnN/MHpdU2LBHcF/tPqxz5kyvQ6GJhD5w=
=rdVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Wed Jun 24 16:27:53 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
virito-blk: drop duplicate check
qemu-iotests: fix 051.out after qdev error message change
iov: don't touch iov in iov_send_recv()
raw-posix: Introduce hdev_is_sg()
raw-posix: Use DPRINTF for DEBUG_FLOPPY
raw-posix: DPRINTF instead of DEBUG_BLOCK_PRINT
Fix migration in case of scsi-generic
block: Use bdrv_is_sg() everywhere
nvme: Fix memleak in nvme_dma_read_prp
vvfat: add a label option
util/hbitmap: Add an API to reset all set bits in hbitmap
virtio-blk: Use blk_drain() to drain IO requests
block-backend: Introduce blk_drain()
throttle: Check current timers before updating any_timer_armed[]
block: Let bdrv_drain_all() to call aio_poll() for each AioContext
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
in_num = req->elem.in_num, and req->elem.in_num is
checked in line 489, so the check about in_num variable
is superflous, let's drop it.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1435138164-11728-1-git-send-email-arei.gonglei@huawei.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We have agreed that OpenFirmware device paths in the "bootorder" fw_cfg
file should follow the pattern
/pci@i0cf8,%x/...
for devices that live behind an extra root bus. The extra root bus in
question is the %x'th among the extra root buses. (In other words, %x
gives the position of the affected extra root bus relative to the other
extra root buses, in bus_nr order.) %x starts at 1, and is formatted in
hex.
The portion of the unit address that comes before the comma is dynamically
taken from the main host bridge, similarly to sysbus_get_fw_dev_path().
Cc: Kevin O'Connor <kevin@koconnor.net>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The sysbus_get_fw_dev_path() function formats OpenFirmware device path
nodes ("driver-name@unit-address") for sysbus devices. The first choice
for "unit-address" is the base address of the device's first MMIO region.
The second choice is its first IO port.
However, if two sysbus devices with the same "driver-name" lack both MMIO
and PIO resources, then there is no good way to distinguish them based on
their OFW nodes, because in this case unit-address is omitted completely
for both devices. An example is TYPE_PXB_HOST ("pxb-host").
For the sake of such devices, introduce the explicit_ofw_unit_address()
"virtual member function". With this function, each sysbus device in the
same SysBusDeviceClass can state its own address.
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
OVMF downloads the ACPI linker/loader script from QEMU when the edk2 PCI
Bus driver globally signals the firmware that PCI enumeration and resource
allocation have completed. At this point QEMU regenerates the ACPI payload
in an fw_cfg read callback, and this is when the PXB's _CRS gets
populated.
Unfortunately, when this happens, the PCI_COMMAND_MEMORY bit is clear in
the root bus's command register, *unlike* under SeaBIOS. The consequences
unfold as follows:
- When build_crs() fetches dev->io_regions[i].addr, it is all-bits-one,
because pci_update_mappings() --> pci_bar_address() calculated it as
PCI_BAR_UNMAPPED, due to the PCI_COMMAND_MEMORY bit being clear.
- Consequently, the SHPC MMIO BAR (bar 0) of the bridge is not added to
the _CRS, *despite* having been programmed in PCI config space.
- Similarly, the SHPC MMIO BAR of the PXB is not removed from the main
root bus's DWordMemory descriptor.
- Guest OSes (Linux and Windows alike) notice the pre-programmed SHPC BAR
within the PXB's config space, and notice that it conflicts with the
main root bus's memory resource descriptors. Linux reports
pci 0000:04:00.0: BAR 0: can't assign mem (size 0x100)
pci 0000:04:00.0: BAR 0: trying firmware assignment [mem
0x88200000-0x882000ff 64bit]
pci 0000:04:00.0: BAR 0: [mem 0x88200000-0x882000ff 64bit] conflicts
with PCI Bus 0000:00 [mem
0x88200000-0xfebfffff]
While Windows Server 2012 R2 reports
https://technet.microsoft.com/en-us/library/cc732199%28v=ws.10%29.aspx
This device cannot find enough free resources that it can use. If you
want to use this device, you will need to disable one of the other
devices on this system. (Code 12)
This issue was apparently encountered earlier, see the "hack" in:
https://lists.nongnu.org/archive/html/qemu-devel/2015-01/msg02983.html
and the current hole-punching logic in build_crs() and build_ssdt() is
probably supposed to remedy exactly that problem -- however, for OVMF they
don't work, because at the end of the PCI enumeration and resource
allocation, which cues the ACPI linker/loader client, the command register
is clear.
The "shpc" property of "pci-bridge", introduced in the previous patches,
allows us to disable the standard hotplug controller cleanly, eliminating
the SHPC bar and the conflict.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the PCI expander bridge, we will want to disable those features of
pci-bridge that relate to SHPC (standard hotplug controller):
- SHPC bar and underlying MemoryRegion
- interrupt (INTx or MSI)
- effective hotplug callbacks
- other SHPC hooks (initialization, cleanup, migration etc)
Introduce a new feature request bit in the PCIBridgeDev.flags field, and
turn off the above if the bit is explicitly cleared.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This should help catch property name typos at compile time.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This should help catch property name typos at compile time.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change the signature of the function-like macro SHPC_VMSTATE(), so that we
can produce and expect this field conditionally in the migration stream,
starting with an upcoming patch.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When loading migration fails due to a disagreement about
PCI config data we don't currently get any errors explaining
that was the cause of the problem or which byte in the config
data was at fault.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is done indirectly by adjusting two typedefs and helps emphasizing
that the respective tables aren't supposed to be modified at runtime
(as they may be shared between devices).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Functions setting errno commonly return just -1, which is of no
particular use in the log file.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Expecting the ROM BAR to be written with an all ones value when sizing
the region is wrong - the low bit has another meaning (enable/disable)
and bits 1..10 are reserved. The PCI spec also mandates writing all
ones to just the address portion of the register.
Use suitable constants also for initializing the ROM BAR register field
description.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
The code introduced to address XSA-126 allows simplification of other
code in xen_pt_initfn(): All we need to do is update "cmd" suitably,
as it'll be written back to the host register near the end of the
function anyway.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Simplifies multiseat configuration, see
docs/multiseat.txt update for details.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
remove some code duplication in acpi-build.c and drop 5
ASL and binary blobs files with TPM ACPI device description,
replacing them with 1 small hunk written in AML API.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We override the error value r in fail_vq, this will cause the caller
can't detect the failure which may cause the caller may disable the
notifiers twice if vhost is failed to start. Fix this by using another
variable to keep track the return value of set_host_notifier().
Fixes b0b3db7955 ("vhost-net: cleanup
host notifiers at last step")
Cc: qemu-stable@nongnu.org
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Excessive virtio_balloon inflation can cause invocation of OOM-killer,
when Linux is under severe memory pressure. Various mechanisms are
responsible for correct virtio_balloon memory management. Nevertheless it
is often the case that these control tools does not have enough time to
react on fast changing memory load. As a result OS runs out of memory and
invokes OOM-killer. The balancing of memory by use of the virtio balloon
should not cause the termination of processes while there are pages in the
balloon. Now there is no way for virtio balloon driver to free memory at
the last moment before some process get killed by OOM-killer.
This does not provide a security breach as balloon itself is running
inside Guest OS and is working in the cooperation with the host. Thus
some improvements from Guest side should be considered as normal.
To solve the problem, introduce a virtio_balloon callback which is
expected to be called from the oom notifier call chain in out_of_memory()
function. If virtio balloon could release some memory, it will make the
system return and retry the allocation that forced the out of memory
killer to run.
This behavior should be enabled if and only if appropriate feature bit
is set on the device. It is off by default.
This functionality was recently merged into vanilla Linux.
commit 5a10b7dbf904bfe01bb9fcc6298f7df09eed77d5
Author: Raushaniya Maksudova <rmaksudova@parallels.com>
Date: Mon Nov 10 09:36:29 2014 +1030
This patch adds respective control bits into QEMU. It introduces
deflate-on-oom option for balloon device which does the trick.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Raushaniya Maksudova <rmaksudova@parallels.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: James Bottomley <JBottomley@Odin.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Each call of the virtio_blk_reset() function calls blk_drain_all(),
which works for all existing BlockDriverStates, while draining only
one is needed.
This patch replaces blk_drain_all() by blk_drain() in
virtio_blk_reset(). virtio_blk_data_plane_stop() should be called
after draining because it restores vblk->complete_request.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Message-id: 1434537440-28236-3-git-send-email-yarygin@linux.vnet.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v038
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-monitor-2015-06-22' into staging
Monitor patches
# gpg: Signature made Mon Jun 22 18:56:18 2015 BST using RSA key ID EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
* remotes/armbru/tags/pull-monitor-2015-06-22: (24 commits)
Include monitor/monitor.h exactly where needed
Include qapi/qmp/qerror.h exactly where needed
qerror: Move #include out of qerror.h
qerror: Finally unused, clean up
qmp: Wean off qerror_report()
tpm: Avoid qerror_report() outside QMP command handlers
qerror: Clean up QERR_ macros to expand into a single string
qerror: Eliminate QERR_DEVICE_NOT_FOUND
vl: Use error_report() for --display errors
vl: Avoid qerror_report() outside QMP command handlers
QemuOpts: Wean off qerror_report_err()
qdev-monitor: Propagate errors through qdev_device_add()
qdev-monitor: Propagate errors through set_property()
qdev-monitor: Convert qbus_find() to Error
qdev-monitor: Fix check for full bus
qdev-monitor: Stop error avalanche in qbus_find_recursive()
disas: Remove uses of CPU env
monitor: Split mon_get_cpu fn to remove ENV_GET_CPU
monitor: Fix failure path for "S" argument
monitor: Point to "help" command on syntax error
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows to assign host input devices to the guest:
qemu -device virtio-input-host-pci,evdev=/dev/input/event<nr>
The guest gets exclusive access to the input device, so be careful
with assigning the keyboard if you have only one connected to your
machine.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move properties from virtio-*-pci to virtio-*-device.
Also make better use of QOM and attach common properties
to the abstract parent classes (virtio-input-device and
virtio-input-pci-device).
Switch the hid device instance init functions over to use
virtio_instance_init_common, so we get the properties of the
virtio device aliased properly to the virtio pci proxy.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Potentially overflowing expression "1 << prop->bitnr" with
type "int" (32 bits, signed) is evaluated using 32-bit arithmetic,
and then used in a context that expects an expression of type
"uint64_t" (64 bits, unsigned).
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Overrunning array "proxy->guest_features" of 2 4-byte
elements at element index 2 (byte offset 8) using index
"proxy->gfselect" (which evaluates to 2). Normally, the
Linux kernel driver just read/write '0' or '1' as the
"proxy->gfselect" values, so using '<' instead of '=<' to
make coverity happy and avoid potential harm.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>