With vfio ioeventfd support, we can program vfio-pci to perform a
specified BAR write when an eventfd is triggered. This allows the
KVM ioeventfd to be wired directly to vfio-pci, entirely avoiding
userspace handling for these events. On the same micro-benchmark
where the ioeventfd got us to almost 90% of performance versus
disabling the GeForce quirks, this gets us to within 95%.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The NVIDIA BAR0 quirks virtualize the PCI config space mirrors found
in device MMIO space. Normally PCI config space is considered a slow
path and further optimization is unnecessary, however NVIDIA uses a
register here to enable the MSI interrupt to re-trigger. Exiting to
QEMU for this MSI-ACK handling can therefore rate limit our interrupt
handling. Fortunately the MSI-ACK write is easily detected since the
quirk MemoryRegion otherwise has very few accesses, so simply looking
for consecutive writes with the same data is sufficient, in this case
10 consecutive writes with the same data and size is arbitrarily
chosen. We configure the KVM ioeventfd with data match, so there's
no risk of triggering for the wrong data or size, but we do risk that
pathological driver behavior might consume all of QEMU's file
descriptors, so we cap ourselves to 10 ioeventfds for this purpose.
In support of the above, generic ioeventfd infrastructure is added
for vfio quirks. This automatically initializes an ioeventfd list
per quirk, disables and frees ioeventfds on exit, and allows
ioeventfds marked as dynamic to be dropped on device reset. The
rationale for this latter feature is that useful ioeventfds may
depend on specific driver behavior and since we necessarily place a
cap on our use of ioeventfds, a machine reset is a reasonable point
at which to assume a new driver and re-profile.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Quirks can be self modifying, provide a hook to allow them to cleanup
on device reset if desired.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This will later be used to include list initialization.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
No declaration of "hw/vfio/vfio-common.h" directly requires to include
the "exec/address-spaces.h" header. To simplify dependencies and
ease the upcoming cleanup of "exec/address-spaces.h", directly include
it in the source file where the declaration are used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-2-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to address_space_translate()
and address_space_translate_cached(). Callers either have an
attrs value to hand, or don't care and can use MEMTXATTRS_UNSPECIFIED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-4-peter.maydell@linaro.org
A recent patch fixed leaks of the dynamically allocated vcdev->vdev.name
field in vfio_ccw_realize(), but we now have three freeing sites for it.
This is unfortunate and seems to indicate something is wrong with its
life cycle.
The root issue is that vcdev->vdev.name is set before vfio_get_device()
is called, which theoretically prevents to call vfio_put_device() to
do the freeing. Well actually, we could call it anyway because
vfio_put_base_device() is a nop if the device isn't attached, but this
would be confusing.
This patch hence moves all the logic of attaching the device, including
the "already attached" check, to a separate vfio_ccw_get_device() function,
counterpart of vfio_put_device(). While here, vfio_put_device() is renamed
to vfio_ccw_put_device() for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <152326891065.266543.9487977590811413472.stgit@bahia.lan>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
During guest OS reboot, guest framebuffer is invalid. It will cause
bugs, if the invalid guest framebuffer is still used by host.
This patch is to introduce vfio_display_reset which is invoked
during vfio display reset. This vfio_display_reset function is used
to release the invalid display resource, disable scanout mode and
replace the invalid surface with QemuConsole's DisplaySurafce.
This patch can fix the GPU hang issue caused by gd_egl_draw during
guest OS reboot.
Changes v3->v4:
- Move dma-buf based display check into the vfio_display_reset().
(Gerd)
Changes v2->v3:
- Limit vfio_display_reset to dma-buf based vfio display. (Gerd)
Changes v1->v2:
- Use dpy_gfx_update_full() update screen after reset. (Gerd)
- Remove dpy_gfx_switch_surface(). (Gerd)
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Message-id: 1524820266-27079-3-git-send-email-tina.zhang@intel.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the subchannel is already attached or if vfio_get_device() fails, the
code jumps to the 'out_device_err' label and doesn't free the string it
has just allocated.
The code should be reworked so that vcdev->vdev.name only gets set when
the device has been attached, and freed when it is about to be detached.
This could be achieved with the addition of a vfio_ccw_get_device()
function that would be the counterpart of vfio_put_device(). But this is
a more elaborate cleanup that should be done in a follow-up. For now,
let's just add calls to g_free() on the buggy error paths.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <152311222681.203086.8874800175539040298.stgit@bahia>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 567b5b309a ("vfio/pci: Relax DMA map errors for MMIO regions")
added an error message if a passed memory section address or size
is not aligned to the page size and thus cannot be DMA mapped.
This patch fixes the trace by printing the region name and the
memory region section offset within the address space (instead of
offset_within_region).
We also turn the error_report into a trace event. Indeed, In some
cases, the traces can be confusing to non expert end-users and
let think the use case does not work (whereas it works as before).
This is the case where a BAR is successively mapped at different
GPAs and its sections are not compatible with dma map. The listener
is called several times and traces are issued for each intermediate
mapping. The end-user cannot easily match those GPAs against the
final GPA output by lscpi. So let's keep those information to
informed users. In mid term, the plan is to advise the user about
BAR relocation relevance.
Fixes: 567b5b309a ("vfio/pci: Relax DMA map errors for MMIO regions")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This adds a possibility for the platform to tell VFIO not to emulate MSIX
so MMIO memory regions do not get split into chunks in flatview and
the entire page can be registered as a KVM memory slot and make direct
MMIO access possible for the guest.
This enables the entire MSIX BAR mapping to the guest for the pseries
platform in order to achieve the maximum MMIO preformance for certain
devices.
Tested on:
LSI Logic / Symbios Logic SAS3008 PCI-Express Fusion-MPT SAS-3 (rev 02)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment we unconditionally avoid mapping MSIX data of a BAR and
emulate MSIX table in QEMU. However it is 1) not always necessary as
a platform may provide a paravirt interface for MSIX configuration;
2) can affect the speed of MMIO access by emulating them in QEMU when
frequently accessed registers share same system page with MSIX data,
this is particularly a problem for systems with the page size bigger
than 4KB.
A new capability - VFIO_REGION_INFO_CAP_MSIX_MAPPABLE - has been added
to the kernel [1] which tells the userspace that mapping of the MSIX data
is possible now. This makes use of it so from now on QEMU tries mapping
the entire BAR as a whole and emulate MSIX on top of that.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a32295c612c57990d17fb0f41e7134394b2f35f6
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
At the moment if vfio_memory_listener is registered in the system memory
address space, it maps/unmaps every RAM memory region for DMA.
It expects system page size aligned memory sections so vfio_dma_map
would not fail and so far this has been the case. A mapping failure
would be fatal. A side effect of such behavior is that some MMIO pages
would not be mapped silently.
However we are going to change MSIX BAR handling so we will end having
non-aligned sections in vfio_memory_listener (more details is in
the next patch) and vfio_dma_map will exit QEMU.
In order to avoid fatal failures on what previously was not a failure and
was just silently ignored, this checks the section alignment to
the smallest supported IOMMU page size and prints an error if not aligned;
it also prints an error if vfio_dma_map failed despite the page size check.
Both errors are not fatal; only MMIO RAM regions are checked
(aka "RAM device" regions).
If the amount of errors printed is overwhelming, the MSIX relocation
could be used to avoid excessive error output.
This is unlikely to cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: Fix Int128 bit ops]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Infrastructure for display support. Must be enabled
using 'display' property.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed By: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The license text currently specifies "any version" of the GPL. It
is unlikely that GPL v1 was ever intended; change this to the
standard "or any later version" text.
Cc: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Cc: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
basename(3) and dirname(3) modify their argument and may return
pointers to statically allocated memory which may be overwritten by
subsequent calls.
g_path_get_basename and g_path_get_dirname have no such issues, and
therefore more preferable.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Message-Id: <1519888086-4207-1-git-send-email-jusual@mail.ru>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After next patch, listener unregister will need the container to be
alive. Let's move this unregister phase to be before unset container,
since that operation will free the backend container in kernel,
otherwise we'll get these after next patch:
qemu-system-x86_64: VFIO_UNMAP_DMA: -22
qemu-system-x86_64: vfio_dma_unmap(0x559bf53a4590, 0x0, 0xa0000) = -22 (Invalid argument)
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180122060244.29368-4-peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These quirks are necessary for GeForce, but not for Quadro/GRID/Tesla
assignment. Leaving them enabled is fully functional and provides the
most compatibility, but due to the unique NVIDIA MSI ACK behavior[1],
it also introduces latency in re-triggering the MSI interrupt. This
overhead is typically negligible, but has been shown to adversely
affect some (very) high interrupt rate applications. This adds the
vfio-pci device option "x-no-geforce-quirks=" which can be set to
"on" to disable this additional overhead.
A follow-on optimization for GeForce might be to make use of an
ioeventfd to allow KVM to trigger an irqfd in the kernel vfio-pci
driver, avoiding the bounce through userspace to handle this device
write.
[1] Background: the NVIDIA driver has been observed to issue a write
to the MMIO mirror of PCI config space in BAR0 in order to allow the
MSI interrupt for the device to retrigger. Older reports indicated a
write of 0xff to the (read-only) MSI capability ID register, while
more recently a write of 0x0 is observed at config space offset 0x704,
non-architected, extended config space of the device (BAR0 offset
0x88704). Virtualization of this range is only required for GeForce.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is already @hostwin in vfio_listener_region_add() so there is no
point in having the other one.
Fixes: 2e4109de8e ("vfio/spapr: Create DMA window dynamically (SPAPR IOMMU v2)")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add the initialization of the mutex protecting the interrupt list.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Recently proposed vfio-pci kernel changes (v4.16) remove the
restriction preventing userspace from mmap'ing PCI BARs in areas
overlapping the MSI-X vector table. This change is primarily intended
to benefit host platforms which make use of system page sizes larger
than the PCI spec recommendation for alignment of MSI-X data
structures (ie. not x86_64). In the case of POWER systems, the SPAPR
spec requires the VM to program MSI-X using hypercalls, rendering the
MSI-X vector table unused in the VM view of the device. However,
ARM64 platforms also support 64KB pages and rely on QEMU emulation of
MSI-X. Regardless of the kernel driver allowing mmaps overlapping
the MSI-X vector table, emulation of the MSI-X vector table also
prevents direct mapping of device MMIO spaces overlapping this page.
Thanks to the fact that PCI devices have a standard self discovery
mechanism, we can try to resolve this by relocating the MSI-X data
structures, either by creating a new PCI BAR or extending an existing
BAR and updating the MSI-X capability for the new location. There's
even a very slim chance that this could benefit devices which do not
adhere to the PCI spec alignment guidelines on x86_64 systems.
This new x-msix-relocation option accepts the following choices:
off: Disable MSI-X relocation, use native device config (default)
auto: Use a known good combination for the platform/device (none yet)
bar0..bar5: Specify the target BAR for MSI-X data structures
If compatible, the target BAR will either be created or extended and
the new portion will be used for MSI-X emulation.
The first obvious user question with this option is how to determine
whether a given platform and device might benefit from this option.
In most cases, the answer is that it won't, especially on x86_64.
Devices often dedicate an entire BAR to MSI-X and therefore no
performance sensitive registers overlap the MSI-X area. Take for
example:
# lspci -vvvs 0a:00.0
0a:00.0 Ethernet controller: Intel Corporation I350 Gigabit Network Connection
...
Region 0: Memory at db680000 (32-bit, non-prefetchable) [size=512K]
Region 3: Memory at db7f8000 (32-bit, non-prefetchable) [size=16K]
...
Capabilities: [70] MSI-X: Enable+ Count=10 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
This device uses the 16K bar3 for MSI-X with the vector table at
offset zero and the pending bits arrary at offset 8K, fully honoring
the PCI spec alignment guidance. The data sheet specifically refers
to this as an MSI-X BAR. This device would not see a benefit from
MSI-X relocation regardless of the platform, regardless of the page
size.
However, here's another example:
# lspci -vvvs 02:00.0
02:00.0 Serial Attached SCSI controller: xxxxxxxx
...
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at ef640000 (64-bit, non-prefetchable) [size=64K]
Region 3: Memory at ef600000 (64-bit, non-prefetchable) [size=256K]
...
Capabilities: [c0] MSI-X: Enable+ Count=16 Masked-
Vector table: BAR=1 offset=0000e000
PBA: BAR=1 offset=0000f000
Here the MSI-X data structures are placed on separate 4K pages at the
end of a 64KB BAR. If our host page size is 4K, we're likely fine,
but at 64KB page size, MSI-X emulation at that location prevents the
entire BAR from being directly mapped into the VM address space.
Overlapping performance sensitive registers then starts to be a very
likely scenario on such a platform. At this point, the user could
enable tracing on vfio_region_read and vfio_region_write to determine
more conclusively if device accesses are being trapped through QEMU.
Upon finding a device and platform in need of MSI-X relocation, the
next problem is how to choose target PCI BAR to host the MSI-X data
structures. A few key rules to keep in mind for this selection
include:
* There are only 6 BAR slots, bar0..bar5
* 64-bit BARs occupy two BAR slots, 'lspci -vvv' lists the first slot
* PCI BARs are always a power of 2 in size, extending == doubling
* The maximum size of a 32-bit BAR is 2GB
* MSI-X data structures must reside in an MMIO BAR
Using these rules, we can evaluate each BAR of the second example
device above as follows:
bar0: I/O port BAR, incompatible with MSI-X tables
bar1: BAR could be extended, incurring another 64KB of MMIO
bar2: Unavailable, bar1 is 64-bit, this register is used by bar1
bar3: BAR could be extended, incurring another 256KB of MMIO
bar4: Unavailable, bar3 is 64bit, this register is used by bar3
bar5: Available, empty BAR, minimum additional MMIO
A secondary optimization we might wish to make in relocating MSI-X
is to minimize the additional MMIO required for the device, therefore
we might test the available choices in order of preference as bar5,
bar1, and finally bar3. The original proposal for this feature
included an 'auto' option which would choose bar5 in this case, but
various drivers have been found that make assumptions about the
properties of the "first" BAR or the size of BARs such that there
appears to be no foolproof automatic selection available, requiring
known good combinations to be sourced from users. This patch is
pre-enabled for an 'auto' selection making use of a validated lookup
table, but no entries are yet identified.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The kernel provides similar emulation of PCI BAR register access to
QEMU, so up until now we've used that for things like BAR sizing and
storing the BAR address. However, if we intend to resize BARs or add
BARs that don't exist on the physical device, we need to switch to the
pure QEMU emulation of the BAR.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add one more layer to our stack of MemoryRegions, this base region
allows us to register BARs independently of the vfio region or to
extend the size of BARs which do map to a region. This will be
useful when we want hypervisor defined BARs or sections of BARs,
for purposes such as relocating MSI-X emulation. We therefore call
msix_init() based on this new base MemoryRegion, while the quirks,
which only modify regions still operate on those sub-MemoryRegions.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The fields were removed in the referenced commit, but the comment
still mentions them.
Fixes: 2fb9636ebf ("vfio-pci: Remove unused fields from VFIOMSIXInfo")
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In order to enable TCE operations support in KVM, we have to inform
the KVM about VFIO groups being attached to specific LIOBNs. The KVM
already knows about VFIO groups, the only bit missing is which
in-kernel TCE table (the one with user visible TCEs) should update
the attached broups. There is an KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE
attribute of the VFIO KVM device which receives a groupfd/tablefd couple.
This uses a new memory_region_iommu_get_attr() helper to get the IOMMU fd
and calls KVM to establish the link.
As get_attr() is not implemented yet, this should cause no behavioural
change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When support for multiple mappings per a region were added, this was
left behind, let's finish and remove unused bits.
Fixes: db0da029a1 ("vfio: Generalize region support")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The vfio_iommu_spapr_tce driver advertises kernel's support for
v1 and v2 IOMMU support, however it is not always possible to use
the requested IOMMU type. For example, a pseries host platform does not
support dynamic DMA windows so v2 cannot initialize and QEMU fails to
start.
This adds a fallback to the v1 IOMMU if v2 cannot be used.
Fixes: 318f67ce13 ("vfio: spapr: Add DMA memory preregistering (SPAPR IOMMU v2)")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The init of giommu_list and hostwin_list is missed during container
initialization.
Signed-off-by: Liu, Yi L <yi.l.liu@linux.intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 8c37faa475 ("vfio-pci, ppc64/spapr: Reorder group-to-container
attaching") moved registration of groups with the vfio-kvm device from
vfio_get_group() to vfio_connect_container(), but it missed the case
where a group is attached to an existing container and takes an early
exit. Perhaps this is a less common case on ppc64/spapr, but on x86
(without viommu) all groups are connected to the same container and
thus only the first group gets registered with the vfio-kvm device.
This becomes a problem if we then hot-unplug the devices associated
with that first group and we end up with KVM being misinformed about
any vfio connections that might remain. Fix by including the call to
vfio_kvm_device_add_group() in this early exit path.
Fixes: 8c37faa475 ("vfio-pci, ppc64/spapr: Reorder group-to-container attaching")
Cc: qemu-stable@nongnu.org # qemu-2.10+
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Simplify the error handling of the SSCH and RSCH handler avoiding
arbitrary and cryptic error codes being used to tell how the instruction
is supposed to end. Let the code detecting the condition tell how it's
to be handled in a less ambiguous way. It's best to handle SSCH and RSCH
in one go as the emulation of the two shares a lot of code.
For passthrough this change isn't pure refactoring, but changes the way
kernel reported EFAULT is handled. After clarifying the kernel interface
we decided that EFAULT shall be mapped to unit exception. Same goes for
unexpected error codes and absence of required ORB flags.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-4-pasic@linux.vnet.ibm.com>
Tested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
[CH: cosmetic changes]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following devices support both PCI Express and Conventional
PCI, by including special code to handle the QEMU_PCI_CAP_EXPRESS
flag and/or conditional pcie_endpoint_cap_init() calls:
* vfio-pci (is_express=1, but legacy PCI handled by
vfio_populate_device())
* vmxnet3 (is_express=0, but PCIe handled by vmxnet3_realize())
* pvscsi (is_express=0, but PCIe handled by pvscsi_realize())
* virtio-pci (is_express=0, but PCIe handled by
virtio_pci_dc_realize(), and additional legacy PCI code at
virtio_pci_realize())
* base-xhci (is_express=1, but pcie_endpoint_cap_init() call
is conditional on pci_bus_is_express(dev->bus)
* Note that xhci does not clear QEMU_PCI_CAP_EXPRESS like the
other hybrid devices
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NVIDIA has defined a specification for creating GPUDirect "cliques",
where devices with the same clique ID support direct peer-to-peer DMA.
When running on bare-metal, tools like NVIDIA's p2pBandwidthLatencyTest
(part of cuda-samples) determine which GPUs can support peer-to-peer
based on chipset and topology. When running in a VM, these tools have
no visibility to the physical hardware support or topology. This
option allows the user to specify hints via a vendor defined
capability. For instance:
<qemu:commandline>
<qemu:arg value='-set'/>
<qemu:arg value='device.hostdev0.x-nv-gpudirect-clique=0'/>
<qemu:arg value='-set'/>
<qemu:arg value='device.hostdev1.x-nv-gpudirect-clique=1'/>
<qemu:arg value='-set'/>
<qemu:arg value='device.hostdev2.x-nv-gpudirect-clique=1'/>
</qemu:commandline>
This enables two cliques. The first is a singleton clique with ID 0,
for the first hostdev defined in the XML (note that since cliques
define peer-to-peer sets, singleton clique offer no benefit). The
subsequent two hostdevs are both added to clique ID 1, indicating
peer-to-peer is possible between these devices.
QEMU only provides validation that the clique ID is valid and applied
to an NVIDIA graphics device, any validation that the resulting
cliques are functional and valid is the user's responsibility. The
NVIDIA specification allows a 4-bit clique ID, thus valid values are
0-15.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If the hypervisor needs to add purely virtual capabilties, give us a
hook through quirks to do that. Note that we determine the maximum
size for a capability based on the physical device, if we insert a
virtual capability, that can change. Therefore if maximum size is
smaller after added virt capabilities, use that.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If vfio_add_std_cap() errors then going to out prepends irrelevant
errors for capabilities we haven't attempted to add as we unwind our
recursive stack. Just return error.
Fixes: 7ef165b9a8 ("vfio/pci: Pass an error object to vfio_add_capabilities")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The existing tries to round up the number of pages but @pages is always
calculated as the rounded up value minus one which makes ctz64() always
return 0 and have create.levels always set 1.
This removes wrong "-1" and allows having more than 1 levels. This becomes
handy for >128GB guests with standard 64K pages as this requires blocks
with zone order 9 and the popular limit of CONFIG_FORCE_MAX_ZONEORDER=9
means that only blocks up to order 8 are allowed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
hw/vfio/pci.c:308:29: warning: Use of memory after it is freed
qemu_set_fd_handler(*pfd, NULL, NULL, vdev);
^~~~
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
free the data _after_ using it.
hw/vfio/platform.c:126:29: warning: Use of memory after it is freed
qemu_set_fd_handler(*pfd, NULL, NULL, NULL);
^~~~
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 7da624e2 ("vfio: Test realized when using VFIOGroup.device_list
iterator") introduced a pointer to the Object DeviceState in the VFIO
common base-device and skipped non-realized devices as we iterate
VFIOGroup.device_list. While it missed to initialize the pointer for
the vfio-ccw case. Let's fix it.
Fixes: 7da624e2 ("vfio: Test realized when using VFIOGroup.device_list
iterator")
Cc: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20170718014926.44781-3-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When allocating memory for the vfio_irq_info parameter of the
VFIO_DEVICE_GET_IRQ_INFO ioctl, we used the wrong size. Let's
fix it by using the right size.
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Jing Zhang <bjzhjing@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170718014926.44781-2-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
At the moment VFIO PCI device initialization works as follows:
vfio_realize
vfio_get_group
vfio_connect_container
register memory listeners (1)
update QEMU groups lists
vfio_kvm_device_add_group
Then (example for pseries) the machine reset hook triggers region_add()
for all regions where listeners from (1) are listening:
ppc_spapr_reset
spapr_phb_reset
spapr_tce_table_enable
memory_region_add_subregion
vfio_listener_region_add
vfio_spapr_create_window
This scheme works fine until we need to handle VFIO PCI device hotplug
and we want to enable PPC64/sPAPR in-kernel TCE acceleration on,
i.e. after PCI hotplug we need a place to call
ioctl(vfio_kvm_device_fd, KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE).
Since the ioctl needs a LIOBN fd (from sPAPRTCETable) and a IOMMU group fd
(from VFIOGroup), vfio_listener_region_add() seems to be the only place
for this ioctl().
However this only works during boot time because the machine reset
happens strictly after all devices are finalized. When hotplug happens,
vfio_listener_region_add() is called when a memory listener is registered
but when this happens:
1. new group is not added to the container->group_list yet;
2. VFIO KVM device is unaware of the new IOMMU group.
This moves bits around to have all necessary VFIO infrastructure
in place for both initial startup and hotplug cases.
[aw: ie, register vfio groups with kvm prior to memory listener
registration such that kvm-vfio pseudo device ioctls are available
during the region_add callback]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This defines new QOM object - IOMMUMemoryRegion - with MemoryRegion
as a parent.
This moves IOMMU-related fields from MR to IOMMU MR. However to avoid
dymanic QOM casting in fast path (address_space_translate, etc),
this adds an @is_iommu boolean flag to MR and provides new helper to
do simple cast to IOMMU MR - memory_region_get_iommu. The flag
is set in the instance init callback. This defines
memory_region_is_iommu as memory_region_get_iommu()!=NULL.
This switches MemoryRegion to IOMMUMemoryRegion in most places except
the ones where MemoryRegion may be an alias.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20170711035620.4232-2-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel 82599 VFs report a PCIe capability version of 0, which is
invalid. The earliest version of the PCIe spec used version 1. This
causes Windows to fail startup on the device and it will be disabled
with error code 10. Our choices are either to drop the PCIe cap on
such devices, which has the side effect of likely preventing the guest
from discovering any extended capabilities, or performing a fixup to
update the capability to the earliest valid version. This implements
the latter.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIOGroup.device_list is effectively our reference tracking mechanism
such that we can teardown a group when all of the device references
are removed. However, we also use this list from our machine reset
handler for processing resets that affect multiple devices. Generally
device removals are fully processed (exitfn + finalize) when this
reset handler is invoked, however if the removal is triggered via
another reset handler (piix4_reset->acpi_pcihp_reset) then the device
exitfn may run, but not finalize. In this case we hit asserts when
we start trying to access PCI helpers since much of the PCI state of
the device is released. To resolve this, add a pointer to the Object
DeviceState in our common base-device and skip non-realized devices
as we iterate.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
After the patch 'Make errp the last parameter of pci_add_capability()',
pci_add_capability() and pci_add_capability2() now do exactly the same.
So drop the wrapper pci_add_capability() of pci_add_capability2(), then
replace the pci_add_capability2() with pci_add_capability() everywhere.
Cc: pbonzini@redhat.com
Cc: rth@twiddle.net
Cc: ehabkost@redhat.com
Cc: mst@redhat.com
Cc: dmitry@daynix.com
Cc: jasowang@redhat.com
Cc: marcel@redhat.com
Cc: alex.williamson@redhat.com
Cc: armbru@redhat.com
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A bunch of fixes all over the place. Most notably this fixes
the new MTU feature when using vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZK2bwAAoJECgfDbjSjVRpNBgIALmNG7VaixhNUlnfX1n1JBnh
+HBP2zNfvi0q5roBuPFmlziKa3IBHb2Fcte4nb6QxmPg+uoaj39AOzfrrvz210kR
h2j5Qk2bCdMeWBpxI+xDDScwi/Im23Y6KN1eZyMekFr2CaSGiqOHZPPdbsyEcHPB
VylM0uHqSTZL5JAAzEuYlH+LLfPu91HoxMsIAdNuQX+qKyM2DZ4eICBQ0zA73USt
OduZltcRMk7UpvQMqY+2iaEXapXQQEUGrP2Mo8ZyqeIl2ItC33GspqBQIKjuZdrr
tpr/T1VWsLdZnURZXyELrFqrErDXvKaP9HROwvyLyYPXZF+pJ3LA7TopS5UmfNQ=
=Z4xG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_upstream' into staging
pci, virtio, vhost: fixes
A bunch of fixes all over the place. Most notably this fixes
the new MTU feature when using vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 29 May 2017 01:10:24 AM BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* mst/tags/for_upstream:
acpi-test: update expected files
pc: ACPI BIOS: use highest NUMA node for hotplug mem hole SRAT entry
vhost-user: pass message as a pointer to process_message_reply()
virtio_net: Bypass backends for MTU feature negotiation
intel_iommu: turn off pt before 2.9
intel_iommu: support passthrough (PT)
intel_iommu: allow dev-iotlb context entry conditionally
intel_iommu: use IOMMU_ACCESS_FLAG()
intel_iommu: provide vtd_ce_get_type()
intel_iommu: renaming context entry helpers
x86-iommu: use DeviceClass properties
memory: remove the last param in memory_region_iommu_replay()
memory: tune last param of iommu_ops.translate()
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We were always passing in that one as "false" to assume that's an read
operation, and we also assume that IOMMU translation would always have
that read permission. A better permission would be IOMMU_NONE since the
replay is after all not a real read operation, but just a page table
rebuilding process.
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Concurrent-sense data is currently not delivered. This patch stores
the concurrent-sense data to the subchannel if a unit check is pending
and the concurrent-sense bit is enabled. Then a TSCH can retreive the
right IRB data back to the guest.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-13-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a new callback on subchannel to handle ccw-request.
Realize the callback in vfio-ccw device. Besides, resort to
the event notifier handler to handling the ccw-request results.
1. Pread the I/O results via MMIO region.
2. Update the scsw info to guest.
3. Inject an I/O interrupt to notify guest the I/O result.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-11-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
vfio-ccw resorts to the eventfd mechanism to communicate with userspace.
We fetch the irqs info via the ioctl VFIO_DEVICE_GET_IRQ_INFO,
register a event notifier to get the eventfd fd which is sent
to kernel via the ioctl VFIO_DEVICE_SET_IRQS, then we can implement
read operation once kernel sends the signal.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-10-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
vfio-ccw provides an MMIO region for I/O operations. We fetch its
information via ioctls here, then we can use it performing I/O
instructions and retrieving I/O results later on.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-9-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We use the IOMMU_TYPE1 of VFIO to realize the subchannels
passthrough, implement a vfio based subchannels passthrough
driver called "vfio-ccw".
Support qemu parameters in the style of:
"-device vfio-ccw,sysfsdev=$mdev_file_path,devno=xx.x.xxxx'
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-8-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
commit 33cd52b5d7 unset
cannot_instantiate_with_device_add_yet in TYPE_SYSBUS, making all
sysbus devices appear on "-device help" and lack the "no-user"
flag in "info qdm".
To fix this, we can set user_creatable=false by default on
TYPE_SYS_BUS_DEVICE, but this requires setting
user_creatable=true explicitly on the sysbus devices that
actually work with -device.
Fortunately today we have just a few has_dynamic_sysbus=1
machines: virt, pc-q35-*, ppce500, and spapr.
virt, ppce500, and spapr have extra checks to ensure just a few
device types can be instantiated:
* virt supports only TYPE_VFIO_CALXEDA_XGMAC, TYPE_VFIO_AMD_XGBE.
* ppce500 supports only TYPE_ETSEC_COMMON.
* spapr supports only TYPE_SPAPR_PCI_HOST_BRIDGE.
This patch sets user_creatable=true explicitly on those 4 device
classes.
Now, the more complex cases:
pc-q35-*: q35 has no sysbus device whitelist yet (which is a
separate bug). We are in the process of fixing it and building a
sysbus whitelist on q35, but in the meantime we can fix the
"-device help" and "info qdm" bugs mentioned above. Also, despite
not being strictly necessary for fixing the q35 bug, reducing the
list of user_creatable=true devices will help us be more
confident when building the q35 whitelist.
xen: We also have a hack at xen_set_dynamic_sysbus(), that sets
has_dynamic_sysbus=true at runtime when using the Xen
accelerator. This hack is only used to allow xen-backend devices
to be dynamically plugged/unplugged.
This means today we can use -device with the following 22 device
types, that are the ones compiled into the qemu-system-x86_64 and
qemu-system-i386 binaries:
* allwinner-ahci
* amd-iommu
* cfi.pflash01
* esp
* fw_cfg_io
* fw_cfg_mem
* generic-sdhci
* hpet
* intel-iommu
* ioapic
* isabus-bridge
* kvmclock
* kvm-ioapic
* kvmvapic
* SUNW,fdtwo
* sysbus-ahci
* sysbus-fdc
* sysbus-ohci
* unimplemented-device
* virtio-mmio
* xen-backend
* xen-sysdev
This patch adds user_creatable=true explicitly to those devices,
temporarily, just to keep 100% compatibility with existing
behavior of q35. Subsequent patches will remove
user_creatable=true from the devices that are really not meant to
user-creatable on any machine, and remove the FIXME comment from
the ones that are really supposed to be user-creatable. This is
being done in separate patches because we still don't have an
obvious list of devices that will be whitelisted by q35, and I
would like to get each device reviewed individually.
Cc: Alexander Graf <agraf@suse.de>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-block@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: sstabellini@kernel.org
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-3-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[ehabkost: Small changes at sysbus_device_class_init() comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When the "No host device provided" error occurs, the hint message
that starts with "Use -vfio-pci," makes no sense, since "-vfio-pci"
is not a valid command line parameter.
Correct this by replacing "-vfio-pci" with "-device vfio-pci".
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch enables 8-byte writes and reads to VFIO. Such implemention
is already done but it's missing the 'case' to handle such accesses in
both vfio_region_write and vfio_region_read and the MemoryRegionOps:
impl.max_access_size and impl.min_access_size.
After this patch, 8-byte writes such as:
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0x4140c, 4)
vfio_region_write (0001:03:00.0:region1+0xc4, 0xa0000, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
goes like this:
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0xbfd0008, 8)
qemu_mutex_unlock unlocked mutex 0x10905ad8
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Sets valid.max_access_size and valid.min_access_size to ensure safe
8-byte accesses to vfio. Today, 8-byte accesses are broken into pairs
of 4-byte calls that goes unprotected:
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0x2020c, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc4, 0xa0000, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
which occasionally leads to:
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0x2030c, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0x1000c, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc4, 0xb0000, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc4, 0xa0000, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
causing strange errors in guest OS. With this patch, such accesses
are protected by the same lock guard:
qemu_mutex_lock locked mutex 0x10905ad8
vfio_region_write (0001:03:00.0:region1+0xc0, 0x2000c, 4)
vfio_region_write (0001:03:00.0:region1+0xc4, 0xb0000, 4)
qemu_mutex_unlock unlocked mutex 0x10905ad8
This happens because the 8-byte write should be broken into 4-byte
writes by memory.c:access_with_adjusted_size() in order to be under
the same lock. Today, it's done in exec.c:address_space_write_continue()
which was able to handle only 4 bytes due to a zero'ed
valid.max_access_size (see exec.c:memory_access_size()).
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In this patch, IOMMUNotifier.{start|end} are introduced to store section
information for a specific notifier. When notification occurs, we not
only check the notification type (MAP|UNMAP), but also check whether the
notified iova range overlaps with the range of specific IOMMU notifier,
and skip those notifiers if not in the listened range.
When removing an region, we need to make sure we removed the correct
VFIOGuestIOMMU by checking the IOMMUNotifier.start address as well.
This patch is solving the problem that vfio-pci devices receive
duplicated UNMAP notification on x86 platform when vIOMMU is there. The
issue is that x86 IOMMU has a (0, 2^64-1) IOMMU region, which is
splitted by the (0xfee00000, 0xfeefffff) IRQ region. AFAIK
this (splitted IOMMU region) is only happening on x86.
This patch also helps vhost to leverage the new interface as well, so
that vhost won't get duplicated cache flushes. In that sense, it's an
slight performance improvement.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1491562755-23867-2-git-send-email-peterx@redhat.com>
[ehabkost: included extra vhost_iommu_region_del() change from Peter Xu]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The NVIDIA BAR5 quirk is targeting an ioport BAR. Some older devices
have a BAR5 which is not ioport and can induce a segfault here. Test
the BAR type to skip these devices.
Link: https://bugs.launchpad.net/qemu/+bug/1678466
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This reverts commit c2b2e158cc.
The original patch intend to prevent linux i915 driver from using
stolen meory. But this patch breaks windows IGD driver loading on
Gen9+, as IGD HW will use stolen memory on Gen9+, once windows IGD
driver see zero size stolen memory, it will unload.
Meanwhile stolen memory will be disabled in 915 when i915 run as
a guest.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[aw: Gen9+ is SkyLake and newer]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Regardless of running in UPT or legacy mode, the guest igd
drivers may attempt to use stolen memory, however only legacy
mode has BIOS support for reserving stolen memmory in the
guest VM. We zero out the stolen memory size in all cases,
then guest igd driver won't use stolen memory.
In legacy mode, user could use x-igd-gms option to specify the
amount of stolen memory which will be pre-allocated and reserved
by bios for igd use.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99028https://bugs.freedesktop.org/show_bug.cgi?id=99025
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Tested-by: Terrence Xu <terrence.xu@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since commit 4bb571d857 ("pci/pcie: don't assume cap id 0 is
reserved") removes the internal use of extended capability ID 0, the
comment here becomes invalid. However, peeling back the onion, the
code is still correct and we still can't seed the capability chain
with ID 0, unless we want to muck with using the version number to
force the header to be non-zero, which is much uglier to deal with.
The comment also now covers some of the subtleties of using cap ID 0,
such as transparently indicating absence of capabilities if none are
added. This doesn't detract from the correctness of the referenced
commit as vfio in the kernel also uses capability ID zero to mask
capabilties. In fact, we should skip zero capabilities precisely
because the kernel might also expose such a capability at the head
position and re-introduce the problem.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Currently we ignore this error, report it with error_reportf_err()
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Linux vfio driver supports to do VFIO_IOMMU_UNMAP_DMA for a very big
region. This can be leveraged by QEMU IOMMU implementation to cleanup
existing page mappings for an entire iova address space (by notifying
with an IOTLB with extremely huge addr_mask). However current
vfio_iommu_map_notify() does not allow that. It make sure that all the
translated address in IOTLB is falling into RAM range.
The check makes sense, but it should only be a sensible checker for
mapping operations, and mean little for unmap operations.
This patch moves this check into map logic only, so that we'll get
faster unmap handling (no need to translate again), and also we can then
better support unmapping a very big region when it covers non-ram ranges
or even not-existing ranges.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A cleanup for vfio_iommu_map_notify(). Now we will fetch vaddr even if
the operation is unmap, but it won't hurt much.
One thing to mention is that we need the RCU read lock to protect the
whole translation and map/unmap procedure.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We traces its range, but we don't know whether it's a MAP/UNMAP. Let's
dump it as well.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both devices seem to be specific to the ARM platform. It's confusing
for the users if they show up on other target architectures, too
(e.g. when the user runs QEMU with "-device ?" to get a list of
supported devices). Thus let's introduce proper configuration switches
so that the devices are only compiled and included when they are
really required.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The device has "bridge" in its name, so it should obviously be in
the category DEVICE_CATEGORY_BRIDGE.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Previous IGD, up through Broadwell, only seem to write GTT values into
the first 1MB of space allocated for the BDSM, but clearly the GTT
can be multiple MB in size. Our test in vfio_igd_quirk_data_write()
correctly filters out indexes beyond 1MB, but given the 1MB mask we're
using, we re-apply writes only to the first 1MB of the guest allocated
BDSM.
We can't assume either the host or guest BDSM is naturally aligned, so
we can't simply apply a different mask. Instead, save the host BDSM
and do the arithmetic to subtract the host value to get the BDSM
offset and add it to the guest allocated BDSM.
Reported-by: Alexander Indenbaum <alexander.indenbaum@gmail.com>
Tested-by: Alexander Indenbaum <alexander.indenbaum@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now the kernel commit 05f0c03fbac1 ("vfio-pci: Allow to mmap
sub-page MMIO BARs if the mmio page is exclusive") allows VFIO
to mmap sub-page BARs. This is the corresponding QEMU patch.
With those patches applied, we could passthrough sub-page BARs
to guest, which can help to improve IO performance for some devices.
In this patch, we expand MemoryRegions of these sub-page
MMIO BARs to PAGE_SIZE in vfio_pci_write_config(), so that
the BARs could be passed to KVM ioctl KVM_SET_USER_MEMORY_REGION
with a valid size. The expanding size will be recovered when
the base address of sub-page BAR is changed and not page aligned
any more in guest. And we also set the priority of these BARs'
memory regions to zero in case of overlap with BARs which share
the same page with sub-page BARs in guest.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When a PCI device is reset, pci_do_device_reset resets all BAR addresses
in the relevant PCIDevice's config buffer.
The VFIO configuration space stays untouched, so the guest OS may choose
to skip restoring the BAR addresses as they would seem intact. The PCI
device may be left non-operational.
One example of such a scenario is when the guest exits S3.
Fix this by resetting the BAR addresses in the VFIO configuration space
as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
As reported in the link below, user has a PCI device with a 4KB BAR
which contains the MSI-X table. This seems to hit a corner case in
the kernel where the region reports being mmap capable, but the sparse
mmap information reports a zero sized range. It's not entirely clear
that the kernel is incorrect in doing this, but regardless, we need
to handle it. To do this, fill our mmap array only with non-zero
sized sparse mmap entries and add an error return from the function
so we can tell the difference between nr_mmaps being zero based on
sparse mmap info vs lack of sparse mmap info.
NB, this doesn't actually change the behavior of the device, it only
removes the scary "Failed to mmap ... Performance may be slow" error
message. We cannot currently create an mmap over the MSI-X table.
Link: http://lists.nongnu.org/archive/html/qemu-discuss/2016-10/msg00009.html
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Setting skip_dump on a MemoryRegion allows us to modify one specific
code path, but the restriction we're trying to address encompasses
more than that. If we have a RAM MemoryRegion backed by a physical
device, it not only restricts our ability to dump that region, but
also affects how we should manipulate it. Here we recognize that
MemoryRegions do not change to sometimes allow dumps and other times
not, so we replace setting the skip_dump flag with a new initializer
so that we know exactly the type of region to which we're applying
this behavior.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
When vfio device is reset(encounter FLR, or bus reset), if need to do
bus reset(vfio_pci_hot_reset_one is called), vfio_pci_pre_reset &
vfio_pci_post_reset will be called twice.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Introductory comment for rtl8168 VFIO MSI-X quirk states:
At BAR2 offset 0x70 there is a dword data register,
offset 0x74 is a dword address register.
vfio: vfio_bar_read(0000:05:00.0:BAR2+0x70, 4) = 0xfee00398 // read data
Thus, correct offset for data read is 0x70,
but function vfio_rtl8168_quirk_data_read() wrongfully uses offset 0x74.
Signed-off-by: Thorsten Kohfeldt <thorsten.kohfeldt@gmx.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case the end-user calls qemu with -vfio-pci option without passing
either sysfsdev or host property value, the device is interpreted as
0000:00:00.0. Let's create a specific error message to guide the end-user.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The returned value (either -errno or -1) is not used anymore by the caller,
vfio_realize, since the error now is stored in the error object. So let's
remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The returned value is not used anymore by the caller, vfio_realize,
since the error now is stored in the error object. So let's remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch converts VFIO PCI to realize function.
Also original initfn errors now are propagated using QEMU
error objects. All errors are formatted with the same pattern:
"vfio: %s: the error description"
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch propagates errors encountered during vfio_base_device_init
up to the realize function.
In case the host value is not set or badly formed we now report an
error.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case the vfio_init_intp fails we currently do not return an
error value. This patch fixes the bug. The returned value is not
explicit but in practice the error object is the one used to
report the error to the end-user and the actual returned error
value is not used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Propagate the vfio_populate_device errors up to vfio_base_device_init.
The error object also is passed to vfio_init_intp. At the moment we
only report the error. Subsequent patches will propagate the error
up to the realize function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
In vfio platform vfio_base_device_init we currently just report the
error. Subsequent patches will propagate the error up to the realize
function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
For the time being let's just simply report the error in
vfio platform's vfio_base_device_init(). A subsequent patch will
duly propagate the error up to vfio_platform_realize.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The error is currently simply reported in vfio_get_group. Don't
bother too much with the prefix which will be handled at upper level,
later on.
Also return an error value in case container->error is not 0 and
the container is teared down.
On vfio_spapr_remove_window failure, we also report an error whereas
it was silent before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
In vfio_probe_igd_bar4_quirk, simply report the error.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The error is cascaded downto vfio_add_std_cap and then vfio_msi(x)_setup,
vfio_setup_pcie_cap.
vfio_add_ext_cap does not return anything else than 0 so let's transform
it into a void function.
Also use pci_add_capability2 which takes an error object.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The error object is propagated down to vfio_intx_enable_kvm().
The three other callers, vfio_intx_enable_kvm(), vfio_msi_disable_common()
and vfio_pci_post_reset() do not propagate the error and simply call
error_reportf_err() with the ERR_PREFIX formatting.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The returned value will be removed later on.
We now format an error in case of reading failure for
- the MSIX flags
- the MSIX table,
- the MSIX PBA.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The returned value will be removed later on.
The case where error recovery cannot be enabled is not converted into
an error object but directly reported through error_report, as before.
Populating an error instead would cause the future realize function to
fail, which is not wanted.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for the same operation in
vfio_populate_device. Eventually this contributes to the migration
to VFIO-PCI realize.
We now report an error on vfio_get_region_info failure.
vfio_probe_igd_bar4_quirk is not involved in the migration to realize
and simply calls error_reportf_err.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To prepare for migration to realize, let's use a local error
object in vfio_initfn. Also let's use the same error prefix for all
error messages.
On top of the 1-1 conversion, we start using a common error prefix for
all error messages. We also introduce a similar warning prefix which will
be used later on.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
IOMMU Notifier list is used for notifying IO address mapping changes.
Currently VFIO is the only user.
However it is possible that future consumer like vhost would like to
only listen to part of its notifications (e.g., cache invalidations).
This patch introduced IOMMUNotifier and IOMMUNotfierFlag bits for a
finer grained control of it.
IOMMUNotifier contains a bitfield for the notify consumer describing
what kind of notification it is interested in. Currently two kinds of
notifications are defined:
- IOMMU_NOTIFIER_MAP: for newly mapped entries (additions)
- IOMMU_NOTIFIER_UNMAP: for entries to be removed (cache invalidates)
When registering the IOMMU notifier, we need to specify one or multiple
types of messages to listen to.
When notifications are triggered, its type will be checked against the
notifier's type bits, and only notifiers with registered bits will be
notified.
(For any IOMMU implementation, an in-place mapping change should be
notified with an UNMAP followed by a MAP.)
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474606948-14391-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
d1f6af6 "kvm-irqchip: simplify kvm_irqchip_add_msi_route" was a cleanup
of kvmchip routing configuration, that was mostly intended for x86.
However, it also contains a subtle change in behaviour which breaks EEH[1]
error recovery on certain VFIO passthrough devices on spapr guests. So far
it's only been seen on a BCM5719 NIC on a POWER8 server, but there may be
other hardware with the same problem. It's also possible there could be
circumstances where it causes a bug on x86 as well, though I don't know of
any obvious candidates.
Prior to d1f6af6, both vfio_msix_vector_do_use() and
vfio_add_kvm_msi_virq() used msg == NULL as a special flag to mark this
as the "dummy" vector used to make the host hardware state sync with the
guest expected hardware state in terms of MSI configuration.
Specifically that flag caused vfio_add_kvm_msi_virq() to become a no-op,
meaning the dummy irq would always be delivered via qemu. d1f6af6 changed
vfio_add_kvm_msi_virq() so it takes a vector number instead of the msg
parameter, and determines the correct message itself. The test for !msg
was removed, and not replaced with anything there or in the caller.
With an spapr guest which has a VFIO device, if an EEH error occurs on the
host hardware, then the device will be isolated then reset. This is a
combination of host and guest action, mediated by some EEH related
hypercalls. I haven't fully traced the mechanics, but somehow installing
the kvm irqchip route for the dummy irq on the BCM5719 means that after EEH
reset and recovery, at least some irqs are no longer delivered to the
guest.
In particular, the guest never gets the link up event, and so the NIC is
effectively dead.
[1] EEH (Enhanced Error Handling) is an IBM POWER server specific PCI-*
error reporting and recovery mechanism. The concept is somewhat
similar to PCI-E AER, but the details are different.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1373802
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Gavin Shan <gwshan@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: qemu-stable@nongnu.org
Fixes: d1f6af6a17 ("kvm-irqchip: simplify kvm_irqchip_add_msi_route")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-4-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
In the past, we are doing gsi route commit for each irqchip route
update. This is not efficient if we are updating lots of routes in the
same time. This patch removes the committing phase in
kvm_irqchip_update_msi_route(). Instead, we do explicit commit after all
routes updated.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Changing the original MSIMessage parameter in kvm_irqchip_add_msi_route
into the vector number. Vector index provides more information than the
MSIMessage, we can retrieve the MSIMessage using the vector easily. This
will avoid fetching MSIMessage every time before adding MSI routes.
Meanwhile, the vector info will be used in the coming patches to further
enable gsi route update notifications.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU supports ARI on downstream ports and assigned devices may support
ARI in their extended capabilities. The endpoint ARI capability
specifies the next function, such that the OS doesn't need to walk
each possible function, however this next function is relative to the
host, not the guest. This leads to device discovery issues when we
combine separate functions into virtual multi-function packages in a
guest. For example, SR-IOV VFs are not enumerated by simply probing
the function address space, therefore the ARI next-function field is
zero. When we combine multiple VFs together as a multi-function
device in the guest, the guest OS identifies ARI is enabled, relies on
this next-function field, and stops looking for additional function
after the first is found.
Long term we should expose the ARI capability to the guest to enable
configurations with more than 8 functions per slot, but this requires
additional QEMU PCI infrastructure to manage the next-function field
for multiple, otherwise independent devices. In the short term,
hiding this capability allows equivalent functionality to what we
currently have on non-express chipsets.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
This ioctl() call to VFIO_IOMMU_SPAPR_TCE_REMOVE was left over from an
earlier version of the code and has since been folded into
vfio_spapr_remove_window().
It wasn't caught because although the argument structure has been removed,
the libc function remove() means this didn't trigger a compile failure.
The ioctl() was also almost certain to fail silently and harmlessly with
the bogus argument, so this wasn't caught in testing.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXe4l4AAoJECgfDbjSjVRpIz4IALye7mKG61/POA4Gqmhalc3d
HnlNSZ2YcKAuvPg7WWkBuRacrQvVY/MbW1mLloG1lY0tdFgZG8Cy+CY6wJg1NE4c
cXd+77vHkIyrnl+Nil+QOgTFiAsMnD+mXHHsnCDw2jGn3JbgVNuCMi7V34fGkQd2
PDkZyYfwTqO3HytuG0/j2Somc9du1gjYdn+9qigfZVgP96jGDojBuJWuuU5flCB3
Kj5xrOuI01XlbdTk71tVjBJBektQurWr6r7GECDqZIpUfc+BI70FU9jPh+OlLTO/
92yi29ncjyStz4tRnf18xoQ8uBgH/tD1xigEUPRtnm1+0i/tgONBL8cAdBF9FBE=
=ABGE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Jul 2016 11:18:32 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (30 commits)
vmw_pvscsi: remove unnecessary internal msi state flag
e1000e: remove unnecessary internal msi state flag
vmxnet3: remove unnecessary internal msi state flag
mptsas: remove unnecessary internal msi state flag
megasas: remove unnecessary megasas_use_msi()
pci: Convert msi_init() to Error and fix callers to check it
pci bridge dev: change msi property type
megasas: change msi/msix property type
mptsas: change msi property type
intel-hda: change msi property type
usb xhci: change msi/msix property type
change pvscsi_init_msi() type to void
tests: add APIC.cphp and DSDT.cphp blobs
tests: acpi: add CPU hotplug testcase
log: Permit -dfilter 0..0xffffffffffffffff
range: Replace internal representation of Range
range: Eliminate direct Range member access
log: Clean up misuse of Range for -dfilter
pci_register_bar: cleanup
Revert "virtio-net: unbreak self announcement and guest offloads after migration"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
msi_init() reports errors with error_report(), which is wrong
when it's used in realize().
Fix by converting it to Error.
Fix its callers to handle failure instead of ignoring it.
For those callers who don't handle the failure, it might happen:
when user want msi on, but he doesn't get what he want because of
msi_init fails silently.
cc: Gerd Hoffmann <kraxel@redhat.com>
cc: John Snow <jsnow@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Hannes Reinecke <hare@suse.de>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Alex Williamson <alex.williamson@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
New VFIO_SPAPR_TCE_v2_IOMMU type supports dynamic DMA window management.
This adds ability to VFIO common code to dynamically allocate/remove
DMA windows in the host kernel when new VFIO container is added/removed.
This adds a helper to vfio_listener_region_add which makes
VFIO_IOMMU_SPAPR_TCE_CREATE ioctl and adds just created IOMMU into
the host IOMMU list; the opposite action is taken in
vfio_listener_region_del.
When creating a new window, this uses heuristic to decide on the TCE table
levels number.
This should cause no guest visible change in behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added some casts to prevent printf() warnings on certain targets
where the kernel headers' __u64 doesn't match uint64_t or PRIx64]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are going to be multiple IOMMUs per a container. This moves
the single host IOMMU parameter set to a list of VFIOHostDMAWindow.
This should cause no behavioral change and will be used later by
the SPAPR TCE IOMMU v2 which will also add a vfio_host_win_del() helper.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes use of the new "memory registering" feature. The idea is
to provide the userspace ability to notify the host kernel about pages
which are going to be used for DMA. Having this information, the host
kernel can pin them all once per user process, do locked pages
accounting (once) and not spent time on doing that in real time with
possible failures which cannot be handled nicely in some cases.
This adds a prereg memory listener which listens on address_space_memory
and notifies a VFIO container about memory which needs to be
pinned/unpinned. VFIO MMIO regions (i.e. "skip dump" regions) are skipped.
The feature is only enabled for SPAPR IOMMU v2. The host kernel changes
are required. Since v2 does not need/support VFIO_IOMMU_ENABLE, this does
not call it when v2 is detected and enabled.
This enforces guest RAM blocks to be host page size aligned; however
this is not new as KVM already requires memory slots to be host page
size aligned.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Fix compile error on 32-bit host]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The IOMMU driver may change behavior depending on whether a notifier
client is present. In the case of POWER, this represents a change in
the visibility of the IOTLB, for other drivers such as intel-iommu and
future AMD-Vi emulation, notifier support is not yet enabled and this
provides the opportunity to flag that incompatibility.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[new log & extracted from [PATCH qemu v17 12/12] spapr_iommu, vfio, memory: Notify IOMMU about starting/stopping listening]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The kernel currently exposes the SR-IOV capability as read-only
through vfio-pci. This is sufficient to protect the host kernel, but
has the potential to confuse guests without further virtualization.
In particular, OVMF tries to size the VF BARs and comes up with absurd
results, ending with an assert. There's not much point in adding
virtualization to a read-only capability, so we simply hide it for
now. If the kernel ever enables SR-IOV virtualization, we should
easily be able to test it through VF BAR sizing or explicit flags.
Testing whether we should parse extended capabilities is also pulled
into the function to keep these assumptions in one place.
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For vfio pcie device, we could expose the extended capability on
PCIE bus. due to add a new pcie capability at the tail of the chain,
in order to avoid config space overwritten, we introduce a copy config
for parsing extended caps. and rebuild the pcie extended config space.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic
alloc and consistent functions") converted VFIOPCIDevice.vga to be
dynamically allocted, negating the need for VFIOPCIDevice.has_vga.
Unfortunately not all of the has_vga users were converted, nor was
the field removed from the structure. Correct these oversights.
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Tested-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Fixes: 2d82f8a3cd ("vfio/pci: Convert all MemoryRegion to dynamic alloc and consistent functions")
Fixes: https://bugs.launchpad.net/qemu/+bug/1591628
Cc: qemu-stable@nongnu.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Every IOMMU has some granularity which MemoryRegionIOMMUOps::translate
uses when translating, however this information is not available outside
the translate context for various checks.
This adds a get_min_page_size callback to MemoryRegionIOMMUOps and
a wrapper for it so IOMMU users (such as VFIO) can know the minimum
actual page size supported by an IOMMU.
As IOMMU MR represents a guest IOMMU, this uses TARGET_PAGE_SIZE
as fallback.
This removes vfio_container_granularity() and uses new helper in
memory_region_iommu_replay() when replaying IOMMU mappings on added
IOMMU memory region.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: Removed an unnecessary calculation]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move all trace-events for files in the hw/vfio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-30-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
vfio_eeh_container_op() is the backend that communicates with
host kernel to support EEH functionality in QEMU. However, the
functon should return the value from host kernel instead of 0
unconditionally.
dwg: Specifically the problem occurs for the handful of EEH
sub-operations which can return a non-zero, non-error result.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: clarification to commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At the moment IOMMU MR only translate to the system memory.
However if some new code changes this, we will need clear indication why
it is not working so here is the check.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since a788f227 "memory: Allow replay of IOMMU mapping notifications"
when new VFIO listener is added, all existing IOMMU mappings are
replayed. However there is a problem that the base address of
an IOMMU memory region (IOMMU MR) is ignored which is not a problem
for the existing user (which is pseries) with its default 32bit DMA
window starting at 0 but it is if there is another DMA window.
This stores the IOMMU's offset_within_address_space and adjusts
the IOVA before calling vfio_dma_map/vfio_dma_unmap.
As the IOMMU notifier expects IOVA offset rather than the absolute
address, this also adjusts IOVA in sPAPR H_PUT_TCE handler before
calling notifier(s).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
7532d3cbf "vfio: Fix 128 bit handling" added support for 64bit IOMMU
memory regions when those are added to VFIO address space; however
removing code cannot cope with these as int128_get64() will fail on
1<<64.
This copies 128bit handling from region_add() to region_del().
Since the only machine type which is actually going to use 64bit IOMMU
is pseries and it never really removes them (instead it will dynamically
add/remove subregions), this should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The IGD OpRegion is enabled automatically when running in legacy mode,
but it can sometimes be useful in universal passthrough mode as well.
Without an OpRegion, output spigots don't work, and even though Intel
doesn't officially support physical outputs in UPT mode, it's a
useful feature. Note that if an OpRegion is enabled but a monitor is
not connected, some graphics features will be disabled in the guest
versus a headless system without an OpRegion, where they would work.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Enable quirks to support SandyBridge and newer IGD devices as primary
VM graphics. This requires new vfio-pci device specific regions added
in kernel v4.6 to expose the IGD OpRegion, the shadow ROM, and config
space access to the PCI host bridge and LPC/ISA bridge. VM firmware
support, SeaBIOS only so far, is also required for reserving memory
regions for IGD specific use. In order to enable this mode, IGD must
be assigned to the VM at PCI bus address 00:02.0, it must have a ROM,
it must be able to enable VGA, it must have or be able to create on
its own an LPC/ISA bridge of the proper type at PCI bus address
00:1f.0 (sorry, not compatible with Q35 yet), and it must have the
above noted vfio-pci kernel features and BIOS. The intention is that
to enable this mode, a user simply needs to assign 00:02.0 from the
host to 00:02.0 in the VM:
-device vfio-pci,host=0000:00:02.0,bus=pci.0,addr=02.0
and everything either happens automatically or it doesn't. In the
case that it doesn't, we leave error reports, but assume the device
will operate in universal passthrough mode (UPT), which doesn't
require any of this, but has a much more narrow window of supported
devices, supported use cases, and supported guest drivers.
When using IGD in this mode, the VM firmware is required to reserve
some VM RAM for the OpRegion (on the order or several 4k pages) and
stolen memory for the GTT (up to 8MB for the latest GPUs). An
additional option, x-igd-gms allows the user to specify some amount
of additional memory (value is number of 32MB chunks up to 512MB) that
is pre-allocated for graphics use. TBH, I don't know of anything that
requires this or makes use of this memory, which is why we don't
allocate any by default, but the specification suggests this is not
actually a valid combination, so the option exists as a workaround.
Please report if it's actually necessary in some environment.
See code comments for further discussion about the actual operation
of the quirks necessary to assign these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Capability probing modifies wmask, which quirks may be interested in
changing themselves. Apply our BAR quirks after the capability scan
to make this possible.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Combine VGA discovery and registration. Quirks can have dependencies
on BARs, so the quirks push out until after we've scanned the BARs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
This function returns success if either we setup the VGA region or
the host vfio doesn't return enough regions to support the VGA index.
This latter case doesn't make any sense. If we're asked to populate
VGA, fail if it doesn't exist and let the caller decide if that's
important.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Given a device specific region type and sub-type, find it. Also
cleanup return point on error in vfio_get_region_info() so that we
always return 0 with a valid pointer or -errno and NULL.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
The sparse mmap capability in a vfio region info allows vfio to tell
us which sub-areas of a region may be mmap'd. Thus rather than
assuming a single mmap covers the entire region and later frobbing it
ourselves for things like the PCI MSI-X vector table, we can read that
directly from vfio.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=DpB8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/awilliam/tags/vfio-update-20160328.0' into staging
VFIO updates 2016-03-28
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
# gpg: Signature made Mon 28 Mar 2016 23:16:52 BST using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg: aka "Alex Williamson <alex@shazbot.org>"
# gpg: aka "Alex Williamson <alwillia@redhat.com>"
# gpg: aka "Alex Williamson <alex.l.williamson@gmail.com>"
* remotes/awilliam/tags/vfio-update-20160328.0:
vfio: convert to 128 bit arithmetic calculations when adding mem regions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vfio_listener_region_add for a iommu mr results in
an overflow assert since iommu memory region is initialized
with UINT64_MAX. Convert calculations to 128 bit arithmetic
for iommu memory regions and let int128_get64 assert for non iommu
regions if there's an overflow.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
[missed (end - 1) on 2nd trace call, move llsize closer to use]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vfio_container_ioctl() was a bad interface that bypassed abstraction
boundaries, had semantics that sat uneasily with its name, and was unsafe
in many realistic circumstances. Now that spapr-pci-vfio-host-bridge has
been folded into spapr-pci-host-bridge, there are no more users, so remove
it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
At present the code handling IBM's Enhanced Error Handling (EEH) interface
on VFIO devices operates by bypassing the usual VFIO logic with
vfio_container_ioctl(). That's a poorly designed interface with unclear
semantics about exactly what can be operated on.
In particular it operates on a single vfio container internally (hence the
name), but takes an address space and group id, from which it deduces the
container in a rather roundabout way. groupids are something that code
outside vfio shouldn't even be aware of.
This patch creates new interfaces for EEH operations. Internally we
have vfio_eeh_container_op() which takes a VFIOContainer object
directly. For external use we have vfio_eeh_as_ok() which determines
if an AddressSpace is usable for EEH (at present this means it has a
single container with exactly one group attached), and vfio_eeh_as_op()
which will perform an operation on an AddressSpace in the unambiguous case,
and otherwise returns an error.
This interface still isn't great, but it's enough of an improvement to
allow a number of cleanups in other places.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Devices like Intel graphics are known to not only have bad checksums,
but also the wrong device ID. This is not so surprising given that
the video BIOS is typically part of the system firmware image rather
that embedded into the device and needs to support any IGD device
installed into the system.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Match common vfio code with setup, exit, and finalize functions for
BAR, quirk, and VGA management. VGA is also changed to dynamic
allocation to match the other MemoryRegions.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Both platform and PCI vfio drivers create a "slow", I/O memory region
with one or more mmap memory regions overlayed when supported by the
device. Generalize this to a set of common helpers in the core that
pulls the region info from vfio, fills the region data, configures
slow mapping, and adds helpers for comleting the mmap, enable/disable,
and teardown. This can be immediately used by the PCI MSI-X code,
which needs to mmap around the MSI-X vector table.
This also changes VFIORegion.mem to be dynamically allocated because
otherwise we don't know how the caller has allocated VFIORegion and
therefore don't know whether to unreference it to destroy the
MemoryRegion or not.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In preparation for supporting capability chains on regions, wrap
ioctl(VFIO_DEVICE_GET_REGION_INFO) so we don't duplicate the code for
each caller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio-pci currently requires a host= parameter, which comes in the
form of a PCI address in [domain:]<bus:slot.function> notation. We
expect to find a matching entry in sysfs for that under
/sys/bus/pci/devices/. vfio-platform takes a similar approach, but
defines the host= parameter to be a string, which can be matched
directly under /sys/bus/platform/devices/. On the PCI side, we have
some interest in using vfio to expose vGPU devices. These are not
actual discrete PCI devices, so they don't have a compatible host PCI
bus address or a device link where QEMU wants to look for it. There's
also really no requirement that vfio can only be used to expose
physical devices, a new vfio bus and iommu driver could expose a
completely emulated device. To fit within the vfio framework, it
would need a kernel struct device and associated IOMMU group, but
those are easy constraints to manage.
To support such devices, which would include vGPUs, that honor the
VFIO PCI programming API, but are not necessarily backed by a unique
PCI address, add support for specifying any device in sysfs. The
vfio API already has support for probing the device type to ensure
compatibility with either vfio-pci or vfio-platform.
With this, a vfio-pci device could either be specified as:
-device vfio-pci,host=02:00.0
or
-device vfio-pci,sysfsdev=/sys/devices/pci0000:00/0000:00:1c.0/0000:02:00.0
or even
-device vfio-pci,sysfsdev=/sys/bus/pci/devices/0000:02:00.0
When vGPU support comes along, this might look something more like:
-device vfio-pci,sysfsdev=/sys/devices/virtual/intel-vgpu/vgpu0@0000:00:02.0
NB - This is only a made up example path
The same change is made for vfio-platform, specifying sysfsdev has
precedence over the old host option.
Tested-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
This just catches a couple of stragglers since I posted
the last clean-includes patchset last week.
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch introduces the amd-xgbe VFIO platform device. It
allows the guest to do passthrough on a device exposing an
"amd,xgbe-seattle-v1a" compat string.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Use the macro PCI_CAP_LIST_NEXT instead of 1, so that the code would be
more self-explain.
This patch makes this change and also fixs one typo in comment.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
this function search the capability from the end, the last
size should 0x100 - pos, not 0xff - pos.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-22-git-send-email-peter.maydell@linaro.org
The PCI spec recommends devices use additional alignment for MSI-X
data structures to allow software to map them to separate processor
pages. One advantage of doing this is that we can emulate those data
structures without a significant performance impact to the operation
of the device. Some devices fail to implement that suggestion and
assigned device performance suffers.
One such case of this is a Mellanox MT27500 series, ConnectX-3 VF,
where the MSI-X vector table and PBA are aligned on separate 4K
pages. If PBA emulation is enabled, performance suffers. It's not
clear how much value we get from PBA emulation, but the solution here
is to only lazily enable the emulated PBA when a masked MSI-X vector
fires. We then attempt to more aggresively disable the PBA memory
region any time a vector is unmasked. The expectation is then that
a typical VM will run entirely with PBA emulation disabled, and only
when used is that emulation re-enabled.
Reported-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Tested-by: Shyam Kaushik <shyam.kaushik@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
For quirks that support the full PCIe extended config space, limit the
quirk to only the size of config space available through vfio. This
allows host systems with broken MMCONFIG regions to still make use of
these quirks without generating bad address faults trying to access
beyond the end of config space exposed through vfio. This may expose
direct access to the mirror of extended config space, only trapping
the sub-range of standard config space, but allowing this makes the
quirk, and thus the device, functional. We expect that only device
specific accesses make use of the mirror, not general extended PCI
capability accesses, so any virtualization in this space is likely
unnecessary anyway, and the device is still IOMMU isolated, so it
should only be able to hurt itself through any bogus configurations
enabled by this space.
Link: https://www.redhat.com/archives/vfio-users/2015-November/msg00192.html
Reported-by: Ronnie Swanink <ronnie@ronnieswanink.nl>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T). Same Coccinelle semantic patch as in commit b45c03f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When we have a PCIe VM, such as Q35, guests start to care more about
valid configurations of devices relative to the VM view of the PCI
topology. Windows will error with a Code 10 for an assigned device if
a PCIe capability is found for a device on a conventional bus. We
also have the possibility of IOMMUs, like VT-d, where the where the
guest may be acutely aware of valid express capabilities on physical
hardware.
Some devices, like tg3 are adversely affected by this due to driver
dependencies on the PCIe capability. The only solution for such
devices is to attach them to an express capable bus in the VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In-kernel ITS emulation on ARM64 will require to supply requester IDs.
These IDs can now be retrieved from the device pointer using new
pci_requester_id() function.
This patch adds pci_dev pointer to KVM GSI routing functions and makes
callers passing it.
x86 architecture does not use requester IDs, but hw/i386/kvm/pci-assign.c
also made passing PCI device pointer instead of NULL for consistency with
the rest of the code.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ce081423ba2394a4efc30f30708fca07656bc500.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At present the memory listener used by vfio to keep host IOMMU mappings
in sync with the guest memory image assumes that if a guest IOMMU
appears, then it has no existing mappings.
This may not be true if a VFIO device is hotplugged onto a guest bus
which didn't previously include a VFIO device, and which has existing
guest IOMMU mappings.
Therefore, use the memory_region_register_iommu_notifier_replay()
function in order to fix this case, replaying existing guest IOMMU
mappings, bringing the host IOMMU into sync with the guest IOMMU.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Depending on the host IOMMU type we determine and record the available page
sizes for IOMMU translation. We'll need this for other validation in
future patches.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The current vfio core code assumes that the host IOMMU is capable of
mapping any IOVA the guest wants to use to where we need. However, real
IOMMUs generally only support translating a certain range of IOVAs (the
"DMA window") not a full 64-bit address space.
The common x86 IOMMUs support a wide enough range that guests are very
unlikely to go beyond it in practice, however the IOMMU used on IBM Power
machines - in the default configuration - supports only a much more limited
IOVA range, usually 0..2GiB.
If the guest attempts to set up an IOVA range that the host IOMMU can't
map, qemu won't report an error until it actually attempts to map a bad
IOVA. If guest RAM is being mapped directly into the IOMMU (i.e. no guest
visible IOMMU) then this will show up very quickly. If there is a guest
visible IOMMU, however, the problem might not show up until much later when
the guest actually attempt to DMA with an IOVA the host can't handle.
This patch adds a test so that we will detect earlier if the guest is
attempting to use IOVA ranges that the host IOMMU won't be able to deal
with.
For now, we assume that "Type1" (x86) IOMMUs can support any IOVA, this is
incorrect, but no worse than what we have already. We can't do better for
now because the Type1 kernel interface doesn't tell us what IOVA range the
IOMMU actually supports.
For the Power "sPAPR TCE" IOMMU, however, we can retrieve the supported
IOVA range and validate guest IOVA ranges against it, and this patch does
so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If a DMA mapping operation fails in vfio_listener_region_add() it
checks to see if we've already completed initial setup of the
container. If so it reports an error so the setup code can fail
gracefully, otherwise throws a hw_error().
There are other potential failure cases in vfio_listener_region_add()
which could benefit from the same logic, so move it to its own
fail: block. Later patches can use this to extend other failure cases
to fail as gracefully as possible under the circumstances.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently the VFIOContainer iommu_data field contains a union with
different information for different host iommu types. However:
* It only actually contains information for the x86-like "Type1" iommu
* Because we have a common listener the Type1 fields are actually used
on all IOMMU types, including the SPAPR TCE type as well
In fact we now have a general structure for the listener which is unlikely
to ever need per-iommu-type information, so this patch removes the union.
In a similar way we can unify the setup of the vfio memory listener in
vfio_connect_container() that is currently split across a switch on iommu
type, but is effectively the same in both cases.
The iommu_data.release pointer was only needed as a cleanup function
which would handle potentially different data in the union. With the
union gone, it too can be removed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In irqfd mode, current code attempts to set a resamplefd whatever
the type of the IRQ. For an edge-sensitive IRQ this attempt fails
and as a consequence, the whole irqfd setup fails and we fall back
to the slow mode. This patch bypasses the resamplefd setting for
non level-sentive IRQs.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
unmask EventNotifier might not be initialized in case of edge
sensitive irq. Using EventNotifier pointers make life simpler to
handle the edge-sensitive irqfd setup.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With current implementation, eventfd VFIO signaling is first set up and
then irqfd is setup, if supported and allowed.
This start sequence causes several issues with IRQ forwarding setup
which, if supported, is transparently attempted on irqfd setup:
IRQ forwarding setup is likely to fail if the IRQ is detected as under
injection into the guest (active at irqchip level or VFIO masked).
This currently always happens because the current sequence explicitly
VFIO-masks the IRQ before setting irqfd.
Even if that masking were removed, we couldn't prevent the case where
the IRQ is under injection into the guest.
So the simpler solution is to remove this 2-step startup and directly
attempt irqfd setup. This is what this patch does.
Also in case the eventfd setup fails, there is no reason to go farther:
let's abort.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Specifying an emulated PCI vendor/device ID can be useful for testing
various quirk paths, even though the behavior and functionality of
the device with bogus IDs is fully unsupportable. We need to use a
uint32_t for the vendor/device IDs, even though the registers
themselves are only 16-bit in order to be able to determine whether
the value is valid and user set.
The same support is added for subsystem vendor/device ID, though these
have the possibility of being useful and supported for more than a
testing tool. An emulated platform might want to impose their own
subsystem IDs or at least hide the physical subsystem ID. Windows
guests will often reinstall drivers due to a change in subsystem IDs,
something that VM users may want to avoid. Of course careful
attention would be required to ensure that guest drivers do not rely
on the subsystem ID as a basis for device driver quirks.
All of these options are added using the standard experimental option
prefix and should not be considered stable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Simplify access to commonly referenced PCI vendor and device ID by
caching it on the VFIOPCIDevice struct.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is just another quirk, for reset rather than affecting memory
regions. Move it to our new quirks file.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Config windows make use of an address register and a data register.
In VGA cards, these are often used to provide real mode code in the
BIOS an easy way to access MMIO registers since the window often
resides in an I/O port register. When the MMIO register has a mirror
of PCI config space, we need to trap those accesses and redirect them
to emulated config space.
The previous version of this functionality made use of a single
MemoryRegion and single match address. This version uses separate
MemoryRegions for each of the address and data registers and allows
for multiple match addresses. This is useful for Nvidia cards which
have two ranges which index into PCI config space.
The previous implementation is left for the follow-on patch for a more
reviewable diff.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Another rework of this quirk, this time to update to the new quirk
structure. We can handle the address and data registers with
separate MemoryRegions and a quirk specific data structure, making the
code much more understandable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The Nvidia 0x3d0 quirk makes use of a two separate registers and gives
us our first chance to make use of separate memory regions for each to
simplify the code a bit.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is an easy quirk that really doesn't need a data structure if
its own. We can pass vdev as the opaque data and access to the
MemoryRegion isn't required.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIOQuirk hosts a single memory region and a fixed set of data fields
that try to handle all the quirk cases, but end up making those that
don't exactly match really confusing. This patch introduces a struct
intended to provide more flexibility and simpler code. VFIOQuirk is
stripped to its basics, an opaque data pointer for quirk specific
data and a pointer to an array of MemoryRegions with a counter. This
still allows us to have common teardown routines, but adds much
greater flexibility to support multiple memory regions and quirk
specific data structures that are easier to maintain. The existing
VFIOQuirk is transformed into VFIOLegacyQuirk, which further patches
will eliminate entirely.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Create a vendor:device ID helper that we'll also use as we rework the
rest of the quirks. Re-reading the config entries, even if we get
more blacklist entries, is trivial overhead and only incurred during
device setup. There's no need to typedef the blacklist structure,
it's a static private data type used once. The elements get bumped
up to uint32_t to avoid future maintenance issues if PCI_ANY_ID gets
used for a blacklist entry (avoiding an actual hardware match). Our
test loop is also crying out to be simplified as a for loop.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The default should be to allow mmap and new drivers shouldn't need to
expose an option or set it to other than the allocation default in
their initfn. Take advantage of the experimental flag to change this
option to the correct polarity.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tracing is more effective when we can completely disable all KVM
bypass paths. Make these runtime rather than build-time configurable.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This allows vfio_msi* tracing. The MSI/X interrupt tracing is also
pulled out of #ifdef DEBUG_VFIO to avoid a recompile for tracing this
path. A few cycles to read the message is hardly anything if we're
already in QEMU.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rename functions and tracing callbacks so that we can trace vfio_intx*
to see all the INTx related activities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With the addition of the Chelsio quirk we have an error path out of
vfio_early_setup_msix() that doesn't free the allocated VFIOMSIXInfo
struct. This doesn't introduce a leak as it still gets freed in the
vfio_put_device() path, but it's complicated and sloppy to rely on
that. Restructure to free the allocated data on error and only link
it into the vdev on success.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
There's quite a bit of cleanup that can be done to the RTL8168 quirk,
as well as the tracing to prevent a spew of uninteresting accesses
for anything else the driver might choose to use the window registers
for besides the MSI-X table. There should be no functional change,
but it's now possible to get compact and useful traces by enabling
vfio_rtl8168_quirk*, ex:
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f000
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f000
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0xfee0100c
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f004
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f004
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x0
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f008
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f008
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x49b1
vfio_rtl8168_quirk_write 0000:04:00.0 [address]: 0x1f00c
vfio_rtl8168_quirk_read 0000:04:00.0 [address]: 0x8001f00c
vfio_rtl8168_quirk_read 0000:04:00.0 [data]: 0x0
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Minor cleanup.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A number of files were including dirent.h but not using any
of the functions it provides
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Many source files have doubled words (eg "the the", "to to",
and so on). Most of these can simply be removed, but a couple
were actual mis-spellings (eg "to to" instead of "to do").
There was even one triple word score "to to to" :-)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
bootindex was incorrectly changed to a device Property during the
platform code split, resulting in it no longer working. Remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.3+
The RTL8168 quirk correctly describes using bit 31 as a signal to
mark a latch/completion, but the code mistakenly uses bit 28. This
causes the Realtek driver to spin on this register for quite a while,
20k cycles on Windows 7 v7.092 driver. Then it gets frustrated and
tries to set the bit itself and spins for another 20k cycles. For
some this still results in a working driver, for others not. About
the only thing the code really does in its current form is protect
the guest from sneaking in writes to the real hardware MSI-X table.
The fix is obviously to use bit 31 as we document that we should.
The other problem doesn't seem to affect current drivers as nobody
seems to use these window registers for writes to the MSI-X table, but
we need to use the stored data when a write is triggered, not the
value of the current write, which only provides the offset.
Note that only the Windows drivers from Realtek seem to use these
registers, the Microsoft drivers provided with Windows 8.1 do not
access them, nor do Linux in-kernel drivers.
Link: https://bugs.launchpad.net/qemu/+bug/1384892
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.1+
Fix pba_offset initialization value for Chelsio T5 Virtual Function
device. The T5 hardware has a bug in it where it reports a Pending Interrupt
Bit Array Offset of 0x8000 for its SR-IOV Virtual Functions instead
of the 0x1000 that the hardware actually uses internally. As the hardware
doesn't return the correct pba_offset value, add a quirk to instead
return a hardcoded value of 0x1000 when a Chelsio T5 VF device is
detected.
This bug has been fixed in the Chelsio's next chip series T6 but there are
no plans to respin the T5 ASIC for this bug. It is just documented in the
T5 Errata and left it at that.
Signed-off-by: Gabriel Laupre <glaupre@chelsio.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On systems with guest visible IOMMU, adding a new memory region onto
PCI bus calls vfio_listener_region_add() for every DMA window. This
installs a notifier for IOMMU memory regions. The notifier is supposed
to be removed vfio_listener_region_del(), however in the case of mixed
PHB (emulated + VFIO devices) when last VFIO device is unplugged and
container gets destroyed, all existing DMA windows stay alive altogether
with the notifiers which are on the linked list which head was in
the destroyed container.
This unregisters IOMMU memory region notifier when a container is
destroyed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch aims at optimizing IRQ handling using irqfd framework.
Instead of handling the eventfds on user-side they are handled on
kernel side using
- the KVM irqfd framework,
- the VFIO driver virqfd framework.
the virtual IRQ completion is trapped at interrupt controller
This removes the need for fast/slow path swap.
Overall this brings significant performance improvements.
Signed-off-by: Alvise Rigo <a.rigo@virtualopensystems.com>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Anticipating for the introduction of new add/remove functions taking
a qemu_irq parameter, let's rename existing ones with a gsi suffix.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is system level code, and should only depend on the host page
size, not the target page size.
Note that HOST_PAGE_SIZE is misleadingly lead and is really aligning
to both host and target page size. Hence it's replacement with
REAL_HOST_PAGE_SIZE.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
size_t is an unsigned type, thus the error case is never reached in
the below call to pread. If bytes is negative, it will be seen as
a very high positive value.
Spotted by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Include linux/vfio.h after sys/ioctl.h, just like in hw/vfio/common.c.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 1434544500-22405-1-git-send-email-leon.alrae@imgtec.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
g_malloc0_n() is introduced since glib-2.24 while QEMU currently
requires glib-2.22. This may cause a link error on some distributions.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The platform device class has become abstract. This patch introduces
a calxeda xgmac device that derives from it.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds the code requested to assign interrupts to
a guest. The interrupts are mediated through user handled
eventfds only.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Minimal VFIO platform implementation supporting register space
user mapping but not IRQ assignment.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Once address_space_translate will be called outside the BQL, the returned
MemoryRegion might disappear as soon as the RCU read-side critical section
ends. Avoid this by moving the critical section to the callers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1426684909-95030-3-git-send-email-pbonzini@redhat.com>
Somehow these GPUs manage not to respond to a PCI bus reset, removing
our primary mechanism for resetting graphics cards. The result is
that these devices typically work well for a single VM boot. If the
VM is rebooted or restarted, the guest driver is not able to init the
card from the dirty state, resulting in a blue screen for Windows
guests.
The workaround is to use a device specific reset. This is not 100%
reliable though since it depends on the incoming state of the device,
but it substantially improves the usability of these devices in a VM.
Credit to Alex Deucher <alexander.deucher@amd.com> for his guidance.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is an impossible error path due to the fact that we're reading a
kernel provided, rather than user provided link, which will certainly
always fit in PATH_MAX. Currently it returns a fixed 26 char path
plus %d group number, which typically maxes out at double digits.
However, the caller of the initfn certainly expects a less-than zero
return value on error, not just a non-zero value. Therefore we
should correct the sign here.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In an analysis by Laszlo, the resulting type of our calculation for
the end of the MSI-X table, and thus the start of memory after the
table, is uint32_t. We're therefore not correctly preventing the
corner case overflow that we intended to fix here where a BAR >=4G
could place the MSI-X table to end exactly at the 4G boundary. The
MSI-X table offset is defined by the hardware spec to 32bits, so we
simply use a cast rather than changing data structure types. This
scenario is purely theoretically, typically the MSI-X table is located
at the front of the BAR.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Rather than retaining io_mem_read/write as simple wrappers around
the memory_region_dispatch_read/write functions, make the latter
public and change all the callers to use them, since we need to
touch all the callsites anyway to add MemTxAttrs and MemTxResult
support. Delete io_mem_read and io_mem_write entirely.
(All the callers currently pass MEMTXATTRS_UNSPECIFIED
and convert the return value back to bool or ignore it.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The patch implements sPAPRPHBClass EEH callbacks so that the EEH
RTAS requests can be routed to VFIO for further handling.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Linux v4.0-rc1 vfio-pci introduced a new virtual interrupt to allow
the kernel to request a device from the user. When signaled, QEMU
will by default attmempt to hot-unplug the device. This is a one-
shot attempt with the expectation that the kernel will continue to
poll for the device if it is not returned. Returning the device when
requested is the expected standard model of cooperative usage, but we
also add an option option to disable this feature. Initially this
opt-out is set as an experimental option because we really should
honor kernel requests for the device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Disabling MMAP support uses the slower read/write accesses but allows to
trace all MMIO accesses, which is not good for performance, but very
useful for reverse engineering PCI drivers. This option allows to
disable MMAP per device without a compile-time change.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
They are not used from anywhere but common.c which is where these are
defined so make them static.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This makes the error report more informative.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This fixes a compiler error which occurs if DEBUG_VFIO is defined.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The difference between v1 and v2 is fairly subtle, simply more
deterministic behavior for unmaps. The v1 interface allows the user
to attempt to unmap sub-regions of previous mappings, returning
success with zero size if unable to comply. This was a reflection of
the underlying IOMMU API. The v2 interface requires that the user
may only unmap fully contained mappings, ie. an unmap cannot intersect
or bisect a previous mapping, but may cover multiple mappings. QEMU
never made use of the sub-region v1 support anyway, so we can support
either v1 or v2. We'll favor v2 since it's newer.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In the case of VFIO, the unrealize callback is too early to munmap the
BARs. The munmap must be delayed until memory accesses are complete.
To do this, split vfio_unmap_bars in two. The removal step, now called
vfio_unregister_bars, remains in vfio_exitfn. The reclamation step
is vfio_unmap_bars and is moved to the instance_finalize callback.
Similarly, quirk MemoryRegions have to be removed during
vfio_unregister_bars, but freeing the data structure must be delayed
to vfio_unmap_bars.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In order to enable out-of-BQL address space lookup, destruction of
devices needs to be split in two phases.
Unrealize is the first phase; once it complete no new accesses will
be started, but there may still be pending memory accesses can still
be completed.
The second part is freeing the device, which only happens once all memory
accesses are complete. At this point the reference count has dropped to
zero, an RCU grace period must have completed (because the RCU-protected
FlatViews hold a reference to the device via memory_region_ref). This is
when instance_finalize is called.
Freeing data belongs in an instance_finalize callback, because the
dynamically allocated memory can still be used after unrealize by the
pending memory accesses.
This starts the process by creating an instance_finalize callback and
freeing most of the dynamically-allocated data in instance_finalize.
Because instance_finalize is also called on error paths or also when
the device is actually not realized, the common code needs some changes
to be ready for this. The error path in vfio_initfn can be simplified too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that vfio_put_base_device is called unconditionally at instance_finalize
time, it can be called twice if vfio_populate_device fails. This works
but it is slightly harder to follow.
Change vfio_get_device to not touch the vbasedev struct until it will
definitely succeed, moving the vfio_populate_device call back to vfio-pci.
This way, vfio_put_base_device will only be called once.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Commit d8d9581460 added explicit object_unparent() calls for
dynamically allocated MemoryRegions. The VFIOMSIXInfo structure also
contains such a MemoryRegion, covering the mmap'd region of a PCI BAR
above the MSI-X table. This structure is freed as part of the class
exit function and therefore also needs an explicit object_unparent().
Failing to do this results in random segfaults due to fields within
the structure, often the class pointer, being reclaimed and corrupted
by the time object_finalize_child_property() is called for the object.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org # 2.2
When disabling MSI/X interrupts the disable functions will leave the
device in INTx mode (when available). This matches how hardware
operates, INTx is enabled unless MSI/X is enabled (DisINTx is handled
separately). Therefore when we really want to disable all interrupts,
such as when removing the device, and we start with the device in
MSI/X mode, we need to pass through INTx on our way to being
completely quiesced.
In well behaved situations, the guest driver will have shutdown the
device and it will start vfio_exitfn() in INTx mode, producing the
desired result. If hot-unplug causes the guest to crash, we may get
the device in MSI/X state, which will leave QEMU with a bogus handler
installed.
Fix this by re-ordering our disable routine so that it should always
finish in VFIO_INT_NONE state, which is what all callers expect.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We use an unsigned int when working with the PCI BAR size, which can
obviously overflow if the BAR is 4GB or larger. This needs to change
to a fixed length uint64_t. A similar issue is possible, though even
more unlikely, when mapping the region above an MSI-X table. The
start of the MSI-X vector table must be below 4GB, but the end, and
therefore the start of the next mapping region, could still land at
4GB.
Suggested-by: Nishank Trivedi <nishank.trivedi@netapp.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Don Slutz <dslutz@verizon.com>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
With the conversion to tracepoints, a couple previous DPRINTKs are
now quite a bit more visible and are really just informational.
Remove these and add a bit more description to another.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
A new common module is created. It implements all functions
that have no device specificity (PCI, Platform).
This patch only consists in move (no functional changes)
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio_get_device now takes a VFIODevice as argument. The function is split
into 2 parts: vfio_get_device which is generic and vfio_populate_device
which is bus specific.
3 new fields are introduced in VFIODevice to store dev_info.
vfio_put_base_device is created.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This structure is going to be shared by VFIOPCIDevice and
VFIOPlatformDevice. VFIOBAR includes it.
vfio_eoi becomes an ops of VFIODevice specialized by parent device.
This makes possible to transform vfio_bar_write/read into generic
vfio_region_write/read that will be used by VFIOPlatformDevice too.
vfio_mmap_bar becomes vfio_map_region
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since we can potentially have both PCI and platform devices in
the same VFIO group, this latter now owns a list of VFIODevices.
A unified reset handler, vfio_reset_handler, is registered, looping
through this VFIODevice list. 2 specialized operations are introduced
(vfio_compute_needs_reset and vfio_hot_reset_multi): they allow to
implement type specific behavior. also reset_works and needs_reset
VFIOPCIDevice fields are moved into VFIODevice.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add 3 new fields in the VFIODevice struct. Type is set to
VFIO_DEVICE_TYPE_PCI. The type enum value will later be used
to discriminate between VFIO PCI and platform devices. The name is
set to domain🚌slot:function. Currently used to test whether
the device already is attached to the group. Later on, the name
will be used to simplify all traces. The group is simply moved
from VFIOPCIDevice to VFIODevice.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
[Fix g_strdup_printf() usage]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Introduce a new base VFIODevice strcut that will be used by both PCI
and Platform VFIO device. Move VFIOPCIDevice fd field there. Obviously
other fields from VFIOPCIDevice will be moved there but this patch
file is introduced to ease the review.
Also vfio_mask_single_irqindex, vfio_unmask_single_irqindex,
vfio_disable_irqindex now take a VFIODevice handle as argument.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To prepare for platform device introduction, rename vfio_mask_intx
and vfio_unmask_intx into vfio_mask_single_irqindex and respectively
unmask_single_irqindex. Also use a nex index parameter.
With that name and prototype the function will be usable for other
indexes than VFIO_PCI_INTX_IRQ_INDEX.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This prepares for the introduction of VFIOPlatformDevice
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is done in preparation for the addition of VFIO platform
device support.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>