Declare PNP0C01 device to reserve MMCONFIG region to conform to the
spec better and play nice with guest BIOSes/OSes.
According to PCI Firmware Specification[0], MMCONFIG region must be
reserved by declaring a motherboard resource. It's optional to reserve
the region in memory map by Int 15 E820h or EFIGetMemoryMap.
Guest Linux checks if the MMCFG region is reserved by bios memory map
or ACPI resource. If it's not reserved, Linux falls back to legacy PCI
configuration access.
TDVF [1] [2] doesn't reserve MMCONFIG the region in memory map.
On the other hand OVMF reserves it in memory map without declaring a
motherboard resource. With memory map reservation, linux guest uses
MMCONFIG region. However it doesn't comply to PCI Firmware
specification.
[0] PCI Firmware specification Revision 3.2
4.1.2 MCFG Table Description table 4-2 NOTE 2
If the operating system does not natively comprehend reserving the
MMCFG region, The MMCFG region must e reserved by firmware. ...
For most systems, the mortheroard resource would appear at the root
of the ACPI namespace (under \_SB)...
The resource can optionally be returned in Int15 E820h or
EFIGetMemoryMap as reserved memory but must always be reported
through ACPI as a motherboard resource
[1] TDX: Intel Trust Domain Extension
https://software.intel.com/content/www/us/en/develop/articles/intel-trust-domain-extensions.html
[2] TDX Virtual Firmware
https://github.com/tianocore/edk2-staging/tree/TDVF
The change to DSDT is as follows.
@@ -68,32 +68,47 @@
If ((CDW3 != Local0))
{
CDW1 |= 0x10
}
CDW3 = Local0
}
Else
{
CDW1 |= 0x04
}
Return (Arg3)
}
}
+
+ Device (DRAC)
+ {
+ Name (_HID, "PNP0C01" /* System Board */) // _HID: Hardware ID
+ Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
+ {
+ DWordMemory (ResourceProducer, PosDecode, MinFixed, MaxFixed, NonCacheable, ReadWrite,
+ 0x00000000, // Granularity
+ 0xB0000000, // Range Minimum
+ 0xBFFFFFFF, // Range Maximum
+ 0x00000000, // Translation Offset
+ 0x10000000, // Length
+ ,, , AddressRangeMemory, TypeStatic)
+ })
+ }
}
Scope (_SB)
{
Device (HPET)
{
Name (_HID, EisaId ("PNP0103") /* HPET System Timer */) // _HID: Hardware ID
Name (_UID, Zero) // _UID: Unique ID
OperationRegion (HPTM, SystemMemory, 0xFED00000, 0x0400)
Field (HPTM, DWordAcc, Lock, Preserve)
{
VEND, 32,
PRD, 32
}
Method (_STA, 0, NotSerialized) // _STA: Status
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <6f686b45ce7bc43048c56dbb46e72e1fe51927e6.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
If SMM is not supported, ACPI fixed hardware doesn't support
legacy-mode. ACPI-only platform. Where SCI_EN in PM1_CNT register is
always set.
The bit tells OS legacy mode(SCI_EN cleared) or ACPI mode(SCI_EN set).
With the next patch (setting fadt.smi_cmd = 0 when smm isn't enabled),
guest Linux tries to switch to ACPI mode, finds smi_cmd = 0, and then
fails to initialize acpi subsystem. This patch proactively fixes it.
This patch changes guest ABI. To keep compatibility, use
"smm-compat" introduced by earlier patch. If the property is true,
disable new behavior.
ACPI spec 4.8.10.1 PM1 Event Grouping
PM1 Eanble Registers
> For ACPI-only platforms (where SCI_EN is always set)
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <500f62081626997e46f96377393d3662211763a8.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following patch will introduce incompatible behavior of SMM.
Introduce a property to keep the old behavior for compatibility.
To enable smm compat, use "-global ICH9-LPC.smm-compat=on" or
"-global PIIX4_PM.smm-compat=on"
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-Id: <47254ae0b8c6cc6945422978b6b2af2d213ef891.1613615732.git.isaku.yamahata@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
When check DMA support for device attached to pxb,
the cache coherency attribute need to be set.
This add _CCA attribute for pxb DSDT.
Fixes: 6f9765fbad ("acpi/gpex: Build tables for pxb")
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1612490205-48788-3-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
When the pcie slot is initialized, by default PCI_EXP_LNKSTA_DLLLA
(Data Link Layer Link Active) is set in PCI_EXP_LNKSTA
(Link Status) without checking if the slot is empty or not.
This is confusing for the kernel because as it sees the link is up
it tries to read the vendor ID and fails:
(From https://bugzilla.kernel.org/show_bug.cgi?id=211691)
[ 1.661105] pcieport 0000:00:02.2: pciehp: Slot Capabilities : 0x0002007b
[ 1.661115] pcieport 0000:00:02.2: pciehp: Slot Status : 0x0010
[ 1.661123] pcieport 0000:00:02.2: pciehp: Slot Control : 0x07c0
[ 1.661138] pcieport 0000:00:02.2: pciehp: Slot #0 AttnBtn+ PwrCtrl+ MRL- AttnInd+ PwrInd+ HotPlug+ Surprise+ Interlock+ NoCompl- IbPresDis- LLActRep+
[ 1.662581] pcieport 0000:00:02.2: pciehp: pciehp_get_power_status: SLOTCTRL 6c value read 7c0
[ 1.662597] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662703] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 1.662706] pcieport 0000:00:02.2: pciehp: pcie_enable_notification: SLOTCTRL 6c write cmd 1031
[ 1.662730] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662748] pcieport 0000:00:02.2: pciehp: pciehp_check_link_active: lnk_status = 2204
[ 1.662750] pcieport 0000:00:02.2: pciehp: Slot(0-2): Link Up
[ 2.896132] pcieport 0000:00:02.2: pciehp: pciehp_check_link_status: lnk_status = 2204
[ 2.896135] pcieport 0000:00:02.2: pciehp: Slot(0-2): No device found
[ 2.896900] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0010 from Slot Status
[ 2.896903] pcieport 0000:00:02.2: pciehp: pciehp_power_off_slot: SLOTCTRL 6c write cmd 400
[ 3.656901] pcieport 0000:00:02.2: pciehp: pending interrupts 0x0009 from Slot Status
This is really a problem with virtio-net failover that hotplugs a VFIO
card during the boot process. The kernel can shutdown the slot while
QEMU is hotplugging it, and this likely ends by an automatic unplug of
the card. At the end of the boot sequence the card has disappeared.
To fix that, don't set the "Link Active" state in the init function, but
rely on the plug function to do it, as the mechanism has already been
introduced by 2f2b18f60b.
Fixes: 2f2b18f60b ("pcie: set link state inactive/active after hot unplug/plug")
Cc: zhengxiang9@huawei.com
Fixes: 3d67447fe7 ("pcie: Fill PCIESlot link fields to support higher speeds and widths")
Cc: alex.williamson@redhat.com
Fixes: b2101eae63 ("pcie: Set the "link active" in the link status register")
Cc: benh@kernel.crashing.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-5-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In failover_add_primary(), we search the id of the failover device by
scanning the list of the devices in the opts list to find a device with
a failover_pair_id equals to the id of the virtio-net device.
If the failover_pair_id is not found, QEMU ignores the primary
device silently (which also means it will not be hidden and
it will be enabled directly at boot).
After that, we search the id in the opts list to do a qdev_device_add()
with it. The device will be always found as otherwise we had exited
before, and thus the warning is never displayed.
Fix that by moving the error report to the first exit condition.
Also add a g_assert() to be sure the compiler will not complain
about a possibly NULL pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-4-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
failover_add_primary() calls qdev_device_add() and doesn't unref
the device. Because of that, when the device is unplugged a reference
is remaining and prevents the cleanup of the object.
This prevents to be able to plugin back the failover primary device,
with errors like:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
(qemu) device_del hostdev0
We can check with "info qtree" and "info pci" that the device has been removed, and then:
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev1,bus=root.3,failover_pair_id=net0
Error: vfio 0000:41:00.0: device is already attached
(qemu) device_add vfio-pci,host=0000:41:00.0,id=hostdev0,bus=root.3,failover_pair_id=net0
qemu-kvm: Duplicate ID 'hostdev0' for device
Fixes: 21e8709b29 ("failover: Remove primary_dev member")
Cc: quintela@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-3-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Commit a1190ab628 has added a "allow_unplug_during_migration = true" at
the end of the main "if" block, so it is not needed to set it anymore
in the previous checking.
Remove it, to have only sub-ifs that check for needed conditions and exit
if one fails.
Fixes: 4f5b6a05a4 ("pci: add option for net failover")
Fixes: a1190ab628 ("migration: allow unplug during migration for failover devices")
Cc: jfreimann@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210212135250.2738750-2-lvivier@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
-----BEGIN PGP SIGNATURE-----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=g7Kx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-20210221' into staging
MIPS patches queue
- Drop redundant struct MemmapEntry (Bin)
- Fix for Coverity CID 1438965 and 1438967 (Jiaxun)
- Add MIPS bootloader API (Jiaxun)
- Use MIPS bootloader API on fuloong2e and boston machines (Jiaxun)
- Add PMON test for Loongson-3A1000 CPU (Jiaxun)
- Convert to translator API (Philippe)
- MMU cleanups (Philippe)
- Promote 128-bit multimedia registers as global ones (Philippe)
- Various cleanups/fixes on the VT82C686B southbridge (Zoltan)
# gpg: Signature made Sun 21 Feb 2021 18:43:57 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-20210221: (43 commits)
vt82c686: Fix superio_cfg_{read,write}() functions
vt82c686: Log superio_cfg unimplemented accesses
vt82c686: Simplify by returning earlier
vt82c686: Reduce indentation by returning early
vt82c686: Remove index field of SuperIOConfig
vt82c686: Move creation of ISA devices to the ISA bridge
vt82c686: Simplify vt82c686b_realize()
vt82c686: Make vt82c686b-pm an abstract base class and add vt8231-pm based on it
vt82c686: Set user_creatable=false for VT82C686B_PM
vt82c686: Fix up power management io base and config
vt82c686: Correctly reset all registers to default values on reset
vt82c686: Correct vt82c686-pm I/O size
vt82c686: Make vt82c686-pm an I/O tracing region
vt82c686: Fix SMBus IO base and configuration registers
vt82c686: Reorganise code
vt82c686: Move superio memory region to SuperIOConfig struct
target/mips: Use GPR move functions in gen_HILO1_tx79()
target/mips: Introduce gen_load_gpr_hi() / gen_store_gpr_hi() helpers
target/mips: Rename 128-bit upper halve GPR registers
target/mips: Promote 128-bit multimedia registers as global ones
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These functions are memory region callbacks so we have to check
against relative address not the mapped address.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 5/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 4/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
By returning earlier we can remove the 'can_write' boolean variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch in 5, this is part 3/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split patch original in 5, this is part 2/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove the separate index value from SuperIOConfig and store
the index at reg 0 which is reserved and returns 0 on read.
This simplifies the object state.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <15b2968fd300a12d06b42368d084f6f80d3c3be5.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch in 5, this is part 1/5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently the ISA devices that are part of the VIA south bridge,
superio chip are wired up by board code. Move creation of these ISA
devices to the VIA ISA bridge model so that board code does not need
to access ISA bus. This also allows vt82c686b-superio to be made
internal to vt82c686 which allows implementing its configuration via
registers in subseqent commits.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <bf9400cc8e4ddd3129aa5678de4d3cf38384805f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove unneeded variables and setting value to 0 on zero initialised
data and replace check for error with error_fatal. Rationalise loop
that sets PCI config header fields read only.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <e4caf35ca10a68f5c74ae3f93fa0bcfa9457beea.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The vt82c686b-pm model can be shared between VT82C686B and VT8231. The
only difference between the two is the device id in what we emulate so
make an abstract via-pm model by renaming appropriately and add types
for vt82c686b-pm and vt8231-pm based on it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <34969fc7be984fa070479bfb9f748993a0aef31b.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This device is part of the multifunction VIA superio/south bridge chip
so not useful in itself.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <d0a806fed5e8055aee4fcf5b2f4790e6dd0f9dc6.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Translate embedded assembly into IO writes which is more
readable.
Also hardcode cm_base at boot time instead of reading from CP0.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-5-jiaxun.yang@flygoat.com>
[PMD: Kept code comments]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here boston)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here fuloong2e)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the loongson3 defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210122122404.11970-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=ipHI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial patches 20210220
# gpg: Signature made Sat 20 Feb 2021 12:34:21 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
MAINTAINERS: Fix default-configs/ entries
target/avr/cpu: Use device_class_set_parent_realize()
hw/scsi/megasas: Remove pointless parenthesis
u2f-passthru: put it into the 'misc' category
tpm: put some tpm devices into the correct category
nvdimm: put it into the 'storage' category
vmmouse: put it into the 'input' category
virtio-pmem: put it into the 'storage' category
MAINTAINERS: add my github tree URL
Fix SPDX-License-Identifier typos
hw/block/fdc: Remove the check_media_rate property
hw/i386/xen: Remove dead code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The category of the u2f-passthru device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20201130083630.2520597-10-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some tpm devices have no category, put them into the correct category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20201130083630.2520597-8-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the nvdimm device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-5-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the vmmouse device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-4-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the virtio-pmem device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Message-Id: <20201130083630.2520597-3-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This was only required for the pc-1.0 and earlier machine types.
Now that these have been removed, we can also drop the corresponding
code from the FDC device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20210203171832.483176-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'drivers_blacklisted' is never accessed, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210202155644.998812-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike SD mode, when SD card is working in SPI mode, the argument
of CMD13 is stuff bits. Hence we should bypass the RCA check.
See "Physical Layer Specification Version 8.00", chapter 7.3.1.3
Detailed Command Description (SPI mode):
"The card shall ignore stuff bits and reserved bits in an argument"
and Table 7-3 Commands and Arguments (SPI mode):
"CMD13 Argument [31:0] stuff bits"
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in CMD24/25 for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in sd_erase() for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These APIs and macros may be referenced by functions that are
currently before them. Move them ahead a little bit.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, CMD30
response type is R1, not R1b.
Fixes: a1bb27b1e9 ("SD card emulation initial implementation")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, the
following commands:
- CMD28 (SET_WRITE_PROT)
- CMD29 (CLR_WRITE_PROT)
- CMD30 (SEND_WRITE_PROT)
are only supported by SDSC cards.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
