For all i, ports_map[i] is used in and only in the i-th iteration.
Replace the dynamic array by a scalar variable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
lsi_bad_phase has a bug in the choice of pmjad1/pmjad2. This does
not matter with Linux guests because it uses just one routine for
both, but it breaks Windows 64-bit guests. This is the text
from the spec:
"[The PMJCTL] bit controls which decision mechanism is used
when jumping on phase mismatch. When this bit is cleared the
LSI53C895A will use Phase Mismatch Jump Address 1 (PMJAD1) when
the WSR bit is cleared and Phase Mismatch Jump Address 2 (PMJAD2)
when the WSR bit is set. When this bit is set the LSI53C895A will
use jump address one (PMJAD1) on data out (data out, command,
message out) transfers and jump address two (PMJAD2) on data in
(data in, status, message in) transfers."
Which means:
CCNTL0.PMJCTL
0 SCNTL2.WSR = 0 PMJAD1
0 SCNTL2.WSR = 1 PMJAD2
1 out PMJAD1
1 in PMJAD2
In qemu, what you get instead is:
CCNTL0.PMJCTL
0 out PMJAD1
0 in PMJAD2 <<<<<
1 out PMJAD1
1 in PMJAD1 <<<<<
Considering that qemu always has SCNTL2.WSR cleared, the two marked cases
(corresponding to phase mismatch on input) are always jumping to the
wrong PMJAD register. The patch implements the correct semantics.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MASTER_DISABLE bit (aka mask-all) masks all the interrupts.
According to Sun-4M System Architecture
"The level–15 interrupt sources [...] are maskable with the Interrupt Target
Mask Register. While these interrupts are considered ’non–maskable’ within
the SPARC IU, a mask capability is provided to allow the boot firmware
to establish a basic environment before receiving any level–15 interrupts,
which are non–maskable within SPARC. A mask–all bit is provided to allow
disabling of all external interrupts during change of the CIT."
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
System architecture dictates whether HAS_AUDIO is defined. It's then
useless to check for HAS_AUDIO in files which are only used on those
architectures which always have audio.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The comment suggests we're checking for the driver in the ready
state and bus master disabled, but the code is checking that it's
not in the ready state.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Found-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
On Host/Fileserver:
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:36 afifo
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:32 blkdev
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:33 chardev
On Guest/Client:
prw-r--r-- 1 guestuser guestuser 0 2010-05-11 12:36 afifo
brw-r--r-- 1 guestuser guestuser 0, 0 2010-05-11 12:32 blkdev
crw-r--r-- 1 guestuser guestuser 4, 5 2010-05-11 12:33 chardev
In the passthrough securit model, specifal files are directly created
on the fileserver. But the user credential
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
Implemntation of symlink in mapped security model:
A regular file is created and the link target is written to it.
readlink() reads it back from the file.
On Guest/Client:
lrwxrwxrwx 1 root root 6 2010-05-11 12:20 asymlink -> afile
On Host/Fileserver:
-rw-------. 1 root root 6 2010-05-11 09:20 asymlink
afile
Under passthrough model, it just calls underlying symlink() readlink()
system calls are used.
Under both security models, client user credentials are changed
after the filesystem objec creation.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the mapped security model, VirtFS server intercepts and maps
the file object create and get/set attribute requests. Files on the fileserver
will be created with VirtFS servers (QEMU) user credentials and the
client-users credentials are stored in extended attributes. On the request
to get attributes, server extracts the client-users credentials
from extended attributes and sends them to the client.
On Host/Fileserver:
-rw-------. 2 virfsuid virtfsgid 0 2010-05-11 09:19 afile
On Guest/Client:
-rw-r--r-- 2 guestuser guestuser 0 2010-05-11 12:19 afile
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
mapped model changes the owner in the extended attributes.
passthrough model does the change through lchown() as the
server don't need to follow the link and client will send the
actual filesystem object.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds required infrastructure for the new security model.
- A new configure option for attr/xattr.
- if CONFIG_VIRTFS will be defined if both CONFIG_LINUX and CONFIG_ATTR defined.
- Defines routines related to both security models.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The new option is:
-fsdev fstype,id=myid,path=/share_path/,security_model=[mapped|passthrough]
-virtfs fstype,path=/share_path/,security_model=[mapped|passthrough],mnt_tag=tag
In the case of mapped security model, files are created with QEMU user
credentials and the client-user's credentials are saved in extended attributes.
Whereas in the case of passthrough security model, files on the
filesystem are directly created with client-user's credentials.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch rearranges the fileop structures by moving the structure definitions
from virtio-9p.c to virtio-9p.h file. No functional changes.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fluesh the debug messages to the log file at the end of each
debug message.
Changes from V1:
Used fflush instead fseek for the flush.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although it is really rare to get in to the while loop, the list
operation in the loop is obviously wrong.
Signed-off-by: Yoshiaki Tamura <tamura.yoshiaki@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add MAINTENANCE_IN and MAINTENANCE_OUT case in
scsi_req_length() for TYPE_ROM with MMC commands. It also adds the MAINTENANCE_OUT
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing write data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add the PERSISTENT_RESERVE_OUT cdb
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing WRITE data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make APICState completely private to apic.c by using DeviceState
in external APIs.
Move apic_init() to pc.c.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Convert to qdev.
Use an opaque CPUState pointer because of missing VMState
implementation for CPUState.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move the actual CPUState contents handling to cpu.h and cpuid.c.
Handle CPU reset and set env->halted in pc.c.
Add a function to get the local APIC state of the current
CPU for the MMIO.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Comparing an 8 bit value with ~0 does not work as expected.
Replace ~0 by UINT8_MAX in comparison and also in assignment
(and fix coding style, too).
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: malc <av1474@comtv.ru>
Correct definitions for FD_CMD_SAVE and FD_CMD_RESTORE in hw/fdc.c
Per https://bugs.launchpad.net/qemu/+bug/424453 the correct values
for FD_CMD_SAVE is 0x2e and FD_CMD_RESTORE is 0x4e. Verified against
the Intel 82078 manual which can be found at:
http://wiki.qemu.org/Documentation/HardwareManuals page 22.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PCI hotplug currently doesn't work after a migration because
we don't migrate the enable bits of the GPE state. Pull hotplug
structs into vmstate.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Setting the ID in pci_nic_init() is a blatant violation of the
DeviceState abstraction. Which even carries a comment advising
against this:
/* This structure should not be accessed directly. We declare it here
so that it can be embedded in individual device state structures. */
What's worse, it bypasses the code ensuring unique qdev IDs: "-device
virtio-net-pci,id=foo -net nic,id=foo -net nic,name=foo" happily
creates three qdevs with ID "foo". That's because qdev relies on
qemu_opts_create() to ensure unique IDs, but -net nic uses a different
QemuOptsList, which means id is in a different namespace. And its
name is not checked for uniqueness at all.
-net nic and pci_add are legacy. Use -device and device_add if you
want a NIC with a qdev ID.
This reverts what's still left of commit eb54b6dc "qdev: add id=
support for pci nics."
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When mistakenly configuring two devices in the same PCI slot,
QEMU gives a not entirely obvious message about a 'devfn' being
in use:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu-kvm: -device virtio-balloon-pci,bus=pci.0,addr=0x3: PCI: devfn 24 not available for virtio-balloon-pci, in use by rtl8139
The user does not configure 'devfn' numbers, they use slot+function.
Thus the error messages should be reported back to the user with that
same terminology rather than the internal QEMU terminology. This
patch makes it report:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu: -device virtio-balloon-pci,bus=pci.0,addr=0x3.7: PCI: slot 3 function 0 not available for virtio-balloon-pci, in use by rtl8139
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Pass the MultiReqBuffer structure down all the way to the I/O submission
instead of takin it apart. Also mark num_writes unsigned as it can't
go negative, and take the check for any pending I/O requests into the
submission function. Last but not least rename do_multiwrite to
virtio_submit_multiwrite to fit the general naming scheme and make clear
what it does.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
There is a 1:1 relation between VirtIOBlock and BlockDriverState instances,
no need to track it because it won't change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a USB keyboard is unplugged, the keyboard eventhandler is never
removed, and events will continue to be passed through to the device,
causing crashes or memory corruption.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently HPET ACPI table is created regardless of whether qemu actually
created hpet device. This may confuse some guests that don't check that
hpet is functional before using it. Solve this by passing info about
hpets in qemu to seabios via fw config interface. Additional benefit is
that seabios no longer uses hard coded hpet configuration. Proposed
interface supports up to 8 hpets. This is the number defined by hpet
spec.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The capability register is read-only from guest POV, so we do not need
to update it on reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change #define DEBUG to #define E1000_DEBUG in hw/e1000.c to make
it possible to build QEMU with -DDEBUG
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Remove unused DEBUG defines from hw/msix.c to avoid having anything
define the word DEBUG without any additions such as MSIX_DEBUG.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the HPET capability of routing IRQs to the front-side
bus, aka MSI support. This feature can be enabled via the qdev property
"msi" and is off by default.
Note that switching it on can cause guests (at least Linux) to use the
HPET as timer instead of the LAPIC. KVM users should recall that only
the latter is currently available as fast in-kernel model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
One HPET block supports up to 32 timers. Allow to instantiate more than
the recommended and implemented minimum of 3. The number is configured
via the qdev property "timers". It is also saved/restored so that it
need not match between migration peers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By implementing this feature we can also remove a nasty way to kill qemu
(by trying to enable level-triggered hpet interrupts).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of keeping a static reference around, pass the state to
hpet_enabled and hpet_get_ticks. All callers now have it at hand. Will
once allow to instantiate the HPET more than a single time.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We have to update the qemu timer when the per-timer enable bit is
toggled, just like for HPET_CFG_ENABLE changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register the HPET as a sysbus device and create it that way. As it can
route its IRQs to any ISA IRQ, we need to connect it to all 24 of them.
Once converted to qdev, we can move reset handler and vmstate
registration into its hands as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Properly initialize HPETTimer::tn and HPETTimer::state once during
hpet_init instead of (re-)writing them on every reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Setting the main counter while the HPET is enabled may not be a good
idea of the guest, but it is supported and should, thus, not spam the
host console with warnings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This moves the private HPET structures into the C module, simplifies
some helper functions and fixes most coding style issues (biggest chunk
was improper switch-case indention). No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Also prevent out-of-bounds write access to the timers but don't spam the
host console if it triggers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
42f1ced228 removed irq lowering
during reset. However, for chip reset command and DMA reset signal,
its actually the correct thing to do.
Lower IRQ on soft reset only.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
BusState::name is allocated in qbus_create_inplace().
So it should be freed by qbus_free().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes the following compilation errors in multiboot.c
when DEBUG_MULTIBOOT is defined.
Use TARGET_FMT_plx instead of %x for target_phys_addr_t.
CC i386-softmmu/multiboot.o
cc1: warnings being treated as errors
qemu/hw/multiboot.c: In function 'mb_add_mod':
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 4 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c: In function 'load_multiboot':
qemu/hw/multiboot.c:279: error: format '%#x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:307: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:308: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
make[1]: *** [multiboot.o] Error 1
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
virtio net attempts to peek into virtio queue to
determine that we have enough space for the complete
packet to fit. However, it fails to account for space
consumed by virtio net header when it does this,
under stress this results in a failure
with the message 'truncating packet'.
redhat bz 591494.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
parse_string() qemu_strdup()s the property value. It is never freed.
It needs to be freed along with the device. Otherwise, the value of
scsi-disk property "ver" gets leaked when hot-unplugging the disk, for
instance.
Call new PropertyInfo method free() from qdev_free(). Implement it
for qdev_prop_string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDEState members drive_serial_str and version are now left empty until
an actual drive is connected. Before, they got a default value that
was overwritten when a drive got connected. Doesn't matter, because
they're used only while a drive is connected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Clean up virtio-blk.c to be more consistent using BDRV_SECTOR_SIZE
instead of hard coded 512 values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
vhost net currently keeps running after vmstop,
which causes trouble as qemy does not check
for dirty pages anymore.
The fix is to simply keep vm and vhost running/stopped
status in sync.
Tested-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previous commit added QMP documentation to the qemu-monitor.hx
file, it's is a copy of this information.
While it's good to keep it near code, maintaining two copies of
the same information is too hard and has little benefit as we
don't expect client writers to consult the code to find how to
use a QMP command.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix for too small allocation to ports_map
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
