The "pnum < nb_sectors" condition in deciding whether to actually copy
data is unnecessarily strict, and the qiov initialization is
unnecessarily for bdrv_aio_write_zeroes and bdrv_aio_discard.
Rewrite mirror_iteration to fix both flaws.
The output of iotests 109 is updated because we now report the offset
and len slightly differently in mirroring progress.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1454637630-10585-2-git-send-email-famz@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
The added parameter can be used to return the BDS pointer which the
valid offset is referring to. Its value should be ignored unless
BDRV_BLOCK_OFFSET_VALID in ret is set.
Until block drivers fill in the right value, let's clear it explicitly
right before calling .bdrv_get_block_status.
The "bs->file" condition in bdrv_co_get_block_status is kept now to keep iotest
case 102 passing, and will be fixed once all drivers return the right file
pointer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1453780743-16806-2-git-send-email-famz@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For bs->file, using references to existing BDSes has been possible for a
while already. This patch enables the same for bs->backing.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
bdrv_replace_in_backing_chain() asserts that not both old and new
BlockDdriverState have a BlockBackend attached to them because both
would have to end up pointing to the new BDS and we don't support more
than one BB per BDS yet.
Before we can safely allow references to existing nodes as backing
files, we need to make sure that even if a backing file has a BB on it,
this doesn't crash qemu.
There are probably also some cases with the 'replaces' option set where
drive-mirror could fail this assertion today. They are fixed with this
error check as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
With dataplane, the ioeventfd events could be dispatched after
mirror_run releases the dirty bitmap, but before mirror_exit actually
does the device switch, because the iothread will still be running, and
it will cause silent data loss.
Fix this by adding a bdrv_drained_begin/end pair around the window, so
that no new external request will be handled.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Add reference count to block job, meanwhile move the ownership of the
reference to job->bs from the caller (which is released in two
completion callbacks) to the block job itself. It is necessary for
block_job_complete_sync to work, because block job shouldn't live longer
than its bs, as asserted in bdrv_delete.
Now block_job_complete_sync can be simplified.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1446765200-3054-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There's nothing preventing the target image from being used by other
operations during the 'drive-mirror' job, so we should block them all
until the job is done.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 82b88fd04cde918a08a6f9a4ab85626d7fd7b502.1446475331.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
These options are only relevant for the user of a whole BDS tree (like a
guest device or a block job) and should thus be moved into the
BlockBackend.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This cleans up the mess we left behind in the mirror code after the
previous patch. Instead of using bdrv_swap(), just change pointers.
The interface change of the mirror job that callers must consider is
that after job completion, their local BDS pointers still point to the
same node now. qemu-img must change its code accordingly (which makes it
easier to understand); the other callers stays unchanged because after
completion they don't do anything with the BDS, but just with the job,
and the job is still owned by the source BDS.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Some block jobs change the block device graph on completion. This means
that the device that owns the job and originally was addressed with its
device name may no longer be what the corresponding BlockBackend points
to.
Previously, the effects of bdrv_swap() ensured that the job was (at
least partially) transferred to the target image. Events that contain
the device name could still use bdrv_get_device_name(job->bs) and get
the same result.
After removing bdrv_swap(), this won't work any more. Instead, save the
device name at job creation and use that copy for QMP events and
anything else identifying the job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This simplifies the code somewhat, especially when dropping whole
backing file subchains.
The exception is the mirroring code that does adventurous things with
bdrv_swap() and in order to keep it working, I had to duplicate most of
bdrv_set_backing_hd() locally. We'll get rid again of this ugliness
shortly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the final step in converting all of the BlockDriverState
pointers that block drivers use to BdrvChild.
After this patch, bs->children contains the full list of child nodes
that are referenced by a given BDS, and these children are only
referenced through BdrvChild, so that updating the pointer in there is
enough for changing edges in the graph.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Simplify memory allocation by sticking with a single API. GSlice
is not that fast anyway (tcmalloc/jemalloc are better).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
During mirror, if the target device does not support zero init, a
mirror may result in a corrupted image for sync="full" mode.
This is due to how the initial dirty bitmap is set up prior to copying
data - we did not mark sectors as dirty that are unallocated. This
means those unallocated sectors are skipped over on the target, and for
a device without zero init, invalid data may reside in those holes.
If both of the following conditions are true, then we will explicitly
mark all sectors as dirty:
1.) sync = "full"
2.) bdrv_has_zero_init(target) == false
If the target does support zero init, but a target image is passed in
with data already present (i.e. an "existing" image), it is assumed the
data present in the existing image is valid data for those sectors.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 91ed4bc5bda7e2b09eb508b07c83f4071fe0b3c9.1443705220.git.jcody@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
We use mirror+replace to fix quorum's broken child. bs/s->common.bs
is quorum, and to_replace is the broken child. The new child is target_bs.
Without this patch, the replace node can be any node, and it can be
top BDS with BB, or another quorum's child. We just check if the broken
child is part of the quorum BDS in this patch.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Message-id: 55A86486.1000404@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes a regression introduced by commit dcfb3beb ("mirror: Do zero
write on target if sectors not allocated"), which was reported to cause
aborts with the message "Co-routine re-entered recursively".
The cause for this bug is the following code in mirror_iteration_done():
if (s->common.busy) {
qemu_coroutine_enter(s->common.co, NULL);
}
This has always been ugly because - unlike most places that reenter - it
doesn't have a specific yield that it pairs with, but is more
uncontrolled. What we really mean here is "reenter the coroutine if
it's in one of the four explicit yields in mirror.c".
This used to be equivalent with s->common.busy because neither
mirror_run() nor mirror_iteration() call any function that could yield.
However since commit dcfb3beb this doesn't hold true any more:
bdrv_get_block_status_above() can yield.
So what happens is that bdrv_get_block_status_above() wants to take a
lock that is already held, so it adds itself to the queue of waiting
coroutines and yields. Instead of being woken up by the unlock function,
however, it gets woken up by mirror_iteration_done(), which is obviously
wrong.
In most cases the code actually happens to cope fairly well with such
cases, but in this specific case, the unlock must already have scheduled
the coroutine for wakeup when mirror_iteration_done() reentered it. And
then the coroutine happened to process the scheduled restarts and tried
to reenter itself recursively.
This patch fixes the problem by pairing the reenter in
mirror_iteration_done() with specific yields instead of abusing
s->common.busy.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 1439455310-11263-1-git-send-email-kwolf@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
If mirror has more free buffers than IOV_MAX, preadv(2)/pwritev(2)
EINVAL failures may be encountered.
It is possible to trigger this by setting granularity to a low value
like 8192.
This patch stops appending chunks once IOV_MAX is reached.
The spurious EINVAL failure can be reproduced with a qcow2 image file
and the following QMP invocation:
qmp.command('drive-mirror', device='virtio0', target='/tmp/r7.s1',
granularity=8192, sync='full', mode='absolute-paths',
format='raw')
While the guest is running dd if=/dev/zero of=/var/tmp/foo oflag=direct
bs=4k.
Cc: Jeff Cody <jcody@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1435761950-26714-1-git-send-email-stefanha@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Limiting to sectors_per_chunk for each bdrv_is_allocated_above is slow,
because the underlying protocol driver would issue much more queries
than necessary. We should coalesce the query.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: <1436413678-7114-4-git-send-email-famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If bus_size is less than 0, the command fails.
If buf_size is 0, use DEFAULT_MIRROR_BUF_SIZE.
If buf_size % granularity is not 0, mirror_free_init() will
do dangerous things.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 5555A588.3080907@cn.fujitsu.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Before, we only yield after initializing dirty bitmap, where the QMP
command would return. That may take very long, and guest IO will be
blocked.
Add sleep points like the later mirror iterations.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1431486673-19280-1-git-send-email-famz@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
There is job resource leak in function mirror_start_job,
although bdrv_create_dirty_bitmap is unlikely failed.
Add block_job_release for each release when needed.
Signed-off-by: Ting Wang <kathy.wangting@huawei.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1435311455-56048-1-git-send-email-kathy.wangting@huawei.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If guest discards a source cluster, mirroring with bdrv_aio_readv is overkill.
Some protocols do zero upon discard, where it's best to use
bdrv_aio_write_zeroes, otherwise, bdrv_aio_discard will be enough.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If specified as "true", it allows discarding on target sectors where source is
not allocated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If we wish to make differential backups a feature that's easy to access,
it might be pertinent to rename the "dirty-bitmap" mode to "incremental"
to make it clear what /type/ of backup the dirty-bitmap is helping us
perform.
This is an API breaking change, but 2.4 has not yet gone live,
so we have this flexibility.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1433463642-21840-2-git-send-email-jsnow@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
The mirror block job is trying to take a clever shortcut if delay_ns is
0 and skips block_job_sleep_ns() in that case. But that function must be
called in every block job iteration, because otherwise it is for example
impossible to pause the job.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We often don't need the BlockDriverState for functions
that operate on bitmaps. Remove it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For "dirty-bitmap" sync mode, the block job will iterate through the
given dirty bitmap to decide if a sector needs backup (backup all the
dirty clusters and skip clean ones), just as allocation conditions of
"top" sync mode.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-11-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The new command pair is added to manage a user created dirty bitmap. The
dirty bitmap's name is mandatory and must be unique for the same device,
but different devices can have bitmaps with the same names.
The granularity is an optional field. If it is not specified, we will
choose a default granularity based on the cluster size if available,
clamped to between 4K and 64K to mirror how the 'mirror' code was
already choosing granularity. If we do not have cluster size info
available, we choose 64K. This code has been factored out into a helper
shared with block/mirror.
This patch also introduces the 'block_dirty_bitmap_lookup' helper,
which takes a device name and a dirty bitmap name and validates the
lookup, returning NULL and setting errp if there is a problem with
either field. This helper will be re-used in future patches in this
series.
The types added to block-core.json will be re-used in future patches
in this series, see:
'qapi: Add transaction support to block-dirty-bitmap-{add, enable, disable}'
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1429314609-29776-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We treat this field with a variety of different types everywhere
in the code. Now it's just uint32_t.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field will be set for user created dirty bitmap. Also pass in an
error pointer to bdrv_create_dirty_bitmap, so when a name is already
taken on this BDS, it can report an error message. This is not global
check, two BDSes can have dirty bitmap with a common name.
Implemented bdrv_find_dirty_bitmap to find a dirty bitmap by name, will
be used later when other QMP commands want to reference dirty bitmap by
name.
Add bdrv_dirty_bitmap_make_anon. This unsets the name of dirty bitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1428069921-2957-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch changes block_job_pause to increase the pause counter and
block_job_resume to decrease it.
The counter will allow calling block_job_pause/block_job_resume
unconditionally on a job when we need to suspend the IO temporarily.
From now on, each block_job_resume must be paired with a block_job_pause
to keep the counter balanced.
The user pause from QMP or HMP will only trigger block_job_pause once
until it's resumed, this is achieved by adding a user_paused flag in
BlockJob.
One occurrence of block_job_resume in mirror_complete is replaced with
block_job_enter which does what is necessary.
In block_job_cancel, the cancel flag is good enough to instruct
coroutines to quit loop, so use block_job_enter to replace the unpaired
block_job_resume.
Upon block job IO error, user is notified about the entering to the
pause state, so this pause belongs to user pause, set the flag
accordingly and expect a matching QMP resume.
[Extended doc comments as suggested by Paolo Bonzini
<pbonzini@redhat.com>.
--Stefan]
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1428069921-2957-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The backing_filename string in mirror_run() is only used to check
for a NULL string, so we don't need to allocate 1024 bytes (or, later,
PATH_MAX bytes), when we only need to copy the first 2 characters.
We technically only need 1 byte, as we are just checking for NULL, but
since backing_filename[] is populated by bdrv_get_backing_filename(), a
string size of 1 will always only return '\0';
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mirror and migration use dirty bitmaps for their purposes, and since
commit [block: per caller dirty bitmap] they use their own bitmaps, not
the global one. But they use old functions bdrv_set_dirty and
bdrv_reset_dirty, which change all dirty bitmaps.
Named dirty bitmaps series by Fam and Snow are affected: mirroring and
migration will spoil all (not related to this mirroring or migration)
named dirty bitmaps.
This patch fixes this by adding bdrv_set_dirty_bitmap and
bdrv_reset_dirty_bitmap, which change concrete bitmap. Also, to prevent
such mistakes in future, old functions bdrv_(set,reset)_dirty are made
static, for internal block usage.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@parallels.com>
CC: John Snow <jsnow@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: Denis V. Lunev <den@openvz.org>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1417081246-3593-1-git-send-email-vsementsov@parallels.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The mirror block job must run in the BlockDriverState AioContext so that
it works with dataplane.
Acquire the AioContext in blockdev.c so starting the block job is safe.
Note that to_replace is treated separately from other BlockDriverStates
in that it does not need to be in the same AioContext. Explicitly
acquire/release to_replace's AioContext when accessing it.
The completion code in block/mirror.c must perform BDS graph
manipulation and bdrv_reopen() from the main loop. Use
block_job_defer_to_main_loop() to achieve that.
The bdrv_drain_all() call is not allowed outside the main loop since it
could lead to lock ordering problems. Use bdrv_drain(bs) instead
because we have acquired the AioContext so nothing else can sneak in
I/O.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1413889440-32577-10-git-send-email-stefanha@redhat.com
Instead of taking the total length of the block device as the block
job's length, use the number of dirty sectors. The progress is now the
number of sectors mirrored to the target block device. Note that this
may result in the job's length increasing during operation, which is
however in fact desirable.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1414159063-25977-8-git-send-email-mreitz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
device_name[] can become non-empty only in bdrv_new_root() and
bdrv_move_feature_fields(). The latter is used only to undo damage
done by bdrv_swap(). The former is called only by blk_new_with_bs().
Therefore, when a BlockDriverState's device_name[] is non-empty, then
it's been created with a BlockBackend, and vice versa. Furthermore,
blk_new_with_bs() keeps the two names equal.
Therefore, device_name[] is redundant. Eliminate it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The gcc 4.1.2 compiler warns that delay_ns may be uninitialized in
mirror_iteration().
There are two break statements in the do ... while loop that skip over
the delay_ns assignment. These are probably the cause of the warning.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoît Canet <benoit.canet@nodalink.com>
Some code in the block layer makes potentially huge allocations. Failure
is not completely unexpected there, so avoid aborting qemu and handle
out-of-memory situations gracefully.
This patch addresses the allocations in the mirror block job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
When mirroring an image of a size that is not a multiple of the
mirror job granularity, the last request would have the right nb_sectors
argument, but a qiov that is rounded up to the next multiple of the
granularity. Don't do this.
This fixes a segfault that is caused by raw-posix being confused by this
and allocating a buffer with request length, but operating on it with
qiov length.
[s/Driver/Drive/ in qemu-iotests 041 as suggested by Eric
--Stefan]
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
drive-mirror will bdrv_swap the new BDS named node-name with the one
pointed by replaces when the mirroring is finished.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When mirroring or active committing a zero length image, BLOCK_JOB_READY
is not reported now, instead the job completes because we short circuit
the mirror job loop.
This is inconsistent with non-zero length images, and only confuses
management software.
Let's do the same thing when seeing a 0-length image: report ready
immediately; wait for block-job-cancel or block-job-complete; clear the
cancel flag as existing non-zero image synced case (cancelled after
ready); then jump to the exit.
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since BLOCK_JOB_COMPLETED, BLOCK_JOB_CANCELLED, BLOCK_JOB_READY are
related, convert them in one patch. The block_job_event_* functions
are used to keep encapsulation of BlockJob structure.
Signed-off-by: Wenchao Xia <wenchaoqemu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
In order to let event defines use existing types later, instead of
redefine new ones, some old type defines for spice and vnc are changed,
and BlockErrorAction is moved from block.h to qapi schema. Note that
BlockErrorAction is not merged with BlockdevOnError.
At this point, VncInfo is not made a child of VncBasicInfo, because
VncBasicInfo has mandatory fields where VncInfo makes them optional.
Signed-off-by: Wenchao Xia <wenchaoqemu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This makes use of op_blocker and blocks all the operations except for
commit target, on each BlockDriverState->backing_hd.
The asserts for op_blocker in bdrv_swap are removed because with this
change, the target of block commit has at least the backing blocker of
its child, so the assertion is not true. Callers should do their check.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_get_info could fail. Add check before using the returned value.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The direct return will skip releasing of all the resouces at
immediate_exit, don't miss that.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Although bdrv_getlength() was just called above this, and checked for
error, it is better to just use the value we already get, and use
DIV_ROUND_UP.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
error_is_set(&var) is the same as var != NULL, but it takes
whole-program analysis to figure that out. Unnecessarily hard for
optimizers, static checkers, and human readers. Commit 84d18f0 dumbed
it down to obvious, but a few more have crept in since, and
documentation was overlooked. Dumb these down, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_getlength could fail, check the return value before using it.
Return NULL and set errno if it fails. Callers are updated to handle
the error case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The mirror blockjob coroutine rate-limits itself by sleeping. The
coroutine also performs I/O asynchronously so it's important that the
aio callback doesn't wake the coroutine early as that breaks
rate-limiting.
Reported-by: Joaquim Barrera <jbarrera@ac.upc.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The throttling delay calculation was using an inaccurate sector count to
calculate the time to sleep. This broke rate-limiting for the block
mirror job.
Move the delay calculation into mirror_iteration() where we know how
many sectors were transferred. This lets us calculate an accurate delay
time.
Reported-by: Joaquim Barrera <jbarrera@ac.upc.edu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Originally, this built up the error message with the backing filename,
so that errp was set as follows:
error_set(errp, QERR_OPEN_FILE_FAILED, backing_filename);
However, we now propagate the local_error from the
bdrv_open_backing_file() call instead, making these 2 lines useless
code.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When starting a block job, commit_active_start() relies on whether *errp
is set by mirror_start_job. This allows it to determine if the mirror
job start failed, so that it can clean up any changes to open flags from
the bdrv_reopen(). If errp is NULL, then it will not be able to
determine if mirror_start_job failed or not.
To avoid this, use a local Error variable, and then propagate the error
(if any) to errp.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There are a handful of places in the block layer where a failure path
has a valid -errno value, yet error_setg() is used. Those instances
should instead use error_setg_errno(), to preserve as much error
information as possible.
This patch replaces those instances with error_setg_errno(), so that
errno is passed up the stack in the error message.
Reported-By: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If the top image to commit is the active layer, and also larger than
the base image, then an I/O error will likely be returned during
block-commit.
For instance, if we have a base image with a virtual size 10G, and a
active layer image of size 20G, then committing the snapshot via
'block-commit' will likely fail.
This will automatically attempt to resize the base image, if the
active layer image to be committed is larger.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the function mirror_iteration() -> qemu_iovec_init(),
it allocates memory for op->qiov.iov, when the write request calls back,
but in the function mirror_iteration_done(), it only frees the op,
not free the op->qiov.iov, so this causes memory leak.
It should use qemu_iovec_destroy() to free op->qiov.
Signed-off-by: Zhang Min <rudy.zhangmin@huawei.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If active is top, it will be mirrored to base, (with block/mirror.c
code), then the image is switched when user completes the block job.
QMP documentation is updated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
commit_active_start is implemented in block/mirror.c, It will create a
job with "commit" type and designated base in block-commit command. This
will be used for committing active layer of device.
Sync mode is removed from MirrorBlockJob because there's no proper type
for commit. The used information is is_none_mode.
The common part of mirror_start and commit_active_start is moved to
mirror_start_job().
Fix the comment wording for commit_start.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows setting the base before entering mirror_run, commit will
make use of it.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Let reference count manage target and don't call bdrv_close here.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Previously a BlockDriverState has only one dirty bitmap, so only one
caller (e.g. a block job) can keep track of writing. This changes the
dirty bitmap to a list and creates a BdrvDirtyBitmap for each caller, the
lifecycle is managed with these new functions:
bdrv_create_dirty_bitmap
bdrv_release_dirty_bitmap
Where BdrvDirtyBitmap is a linked list wrapper structure of HBitmap.
In place of bdrv_set_dirty_tracking, a BdrvDirtyBitmap pointer argument
is added to these functions, since each caller has its own dirty bitmap:
bdrv_get_dirty
bdrv_dirty_iter_init
bdrv_get_dirty_count
bdrv_set_dirty and bdrv_reset_dirty prototypes are unchanged but will
internally walk the list of all dirty bitmaps and set them one by one.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Switch the string to enum type BlockJobType in BlockJobDriver.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We will use BlockJobType as the enum type name of block jobs in QAPI,
rename current BlockJobType to BlockJobDriver, which will eventually
become a set of operations, similar to block drivers.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error ** parameter to bdrv_open, bdrv_file_open and associated
functions to allow more specific error messages.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now that bdrv_is_allocated detects coroutine context, the two can
use the same code.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Manage BlockDriverState lifecycle with refcnt, so bdrv_delete() is no
longer public and should be called by bdrv_unref() if refcnt is
decreased to 0.
This is an identical change because effectively, there's no multiple
reference of BDS now: no caller of bdrv_ref() yet, only bdrv_new() sets
bs->refcnt to 1, so all bdrv_unref() now actually delete the BDS.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Convert block_job_sleep_ns and co_sleep_ns to use the new timer
API.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Options starting in "backing." are passed to the backing file now. If
you don't need to specify the filename for the backing file, you can add
it on the command line instead of in the image file:
$ qemu-nbd -t /tmp/test.img
$ qemu-img create -f qcow2 empty.qcow2 1G
$ qemu-system-x86_64 -drive file=empty.qcow2,backing.file.driver=nbd,\
backing.file.host=localhost
Note that this doesn't override the backing filename from the image. If
the image has one, this will fail because NBD doesn't want the options
and a filename at the same time.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
On a zero-sized disk we need to break out of the job successfully
before bdrv_dirty_iter_init is called, otherwise you will get an
assertion failure with the next patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Yet another optimization is to extend the mirroring iteration to include more
adjacent dirty blocks. This limits the number of I/O operations and makes
mirroring efficient even with a small granularity. Most of the infrastructure
is already in place; we only need to put a loop around the computation of
the origin and sector count of the iteration.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With AIO support in place, we can start copying more than one chunk
in parallel. This patch introduces the required infrastructure for
this: the buffer is split into multiple granularity-sized chunks,
and there is a free list to access them.
Because of copy-on-write, a single operation may already require
multiple chunks to be available on the free list.
In addition, two different iterations on the HBitmap may want to
copy the same cluster. We avoid this by keeping a bitmap of in-flight
I/O operations, and blocking until the previous iteration completes.
This should be a pretty rare occurrence, though; as long as there is
no overlap the next iteration can start before the previous one finishes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes sense when the next commit starts using the extra buffer space
to perform many I/O operations asynchronously.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is really no change in the behavior of the job here, since
there is still a maximum of one in-flight I/O operation between
the source and the target. However, this patch already introduces
the AIO callbacks (which are unmodified in the next patch)
and some of the logic to count in-flight operations and only
complete the job when there is none.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The desired granularity may be very different depending on the kind of
operation (e.g. continuous replication vs. collapse-to-raw) and whether
the VM is expected to perform lots of I/O while mirroring is in progress.
Allow the user to customize it, while providing a sane default so that
in general there will be no extra allocated space in the target compared
to the source.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When mirroring runs, the backing files for the target may not yet be
ready. However, this means that a copy-on-write operation on the target
would fill the missing sectors with zeros. Copy-on-write only happens
if the granularity of the dirty bitmap is smaller than the cluster size
(and only for clusters that are allocated in the source after the job
has started copying). So far, the granularity was fixed to 1MB; to avoid
the problem we detected the situation and required the backing files to
be available in that case only.
However, we want to lower the granularity for efficiency, so we need
a better solution. The solution is to always copy a whole cluster the
first time it is touched. The code keeps a bitmap of clusters that
have already been allocated by the mirroring job, and only does "manual"
copy-on-write if the chunk being copied is zero in the bitmap.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This actually uses the dirty bitmap in the block layer, and converts
mirroring to use an HBitmapIter.
Reviewed-by: Laszlo Ersek <lersek@redhat.com> (except block/mirror.c parts)
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It allocates with qemu_blockalign(), therefore it must free with
qemu_vfree(), not g_free().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Error management is important for mirroring; otherwise, an error on the
target (even something as "innocent" as ENOSPC) requires to start again
with a full copy. Similar to on_read_error/on_write_error, two separate
knobs are provided for on_source_error (reads) and on_target_error (writes).
The default is 'report' for both.
The 'ignore' policy will leave the sector dirty, so that it will be
retried later. Thus, it will not cause corruption.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Switching to the target of the migration is done mostly asynchronously,
and reported to management via the BLOCK_JOB_COMPLETED event; the only
synchronous phase is opening the backing files. bdrv_open_backing_file
can always be done, even for migration of the full image (aka sync:
'full'). In this case, qmp_drive_mirror will create the target disk
with no backing file at all, and bdrv_open_backing_file will be a no-op.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the implementation of a new job that mirrors a disk to
a new image while letting the guest continue using the old image.
The target is treated as a "black box" and data is copied from the
source to the target in the background. This can be used for several
purposes, including storage migration, continuous replication, and
observation of the guest I/O in an external program. It is also a
first step in replacing the inefficient block migration code that is
part of QEMU.
The job is possibly never-ending, but it is logically structured into
two phases: 1) copy all data as fast as possible until the target
first gets in sync with the source; 2) keep target in sync and
ensure that reopening to the target gets a correct (full) copy
of the source data.
The second phase is indicated by the progress in "info block-jobs"
reporting the current offset to be equal to the length of the file.
When the job is cancelled in the second phase, QEMU will run the
job until the source is clean and quiescent, then it will report
successful completion of the job.
In other words, the BLOCK_JOB_CANCELLED event means that the target
may _not_ be consistent with a past state of the source; the
BLOCK_JOB_COMPLETED event means that the target is consistent with
a past state of the source. (Note that it could already happen
that management lost the race against QEMU and got a completion
event instead of cancellation).
It is not yet possible to complete the job and switch over to the target
disk. The next patches will fix this and add many refinements to the
basic idea introduced here. These include improved error management,
some tunable knobs and performance optimizations.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>