We have a couple places in the code base that want to deep-clone
one QAPI object into another, and they were resorting to serializing
the struct out to QObject then reparsing it. A much more efficient
version can be done by adding a new clone visitor.
Since cloning is still relatively uncommon, expose the use of the
new visitor via a QAPI_CLONE() macro that takes care of type-punning
the underlying function pointer, rather than generating lots of
unused functions for types that won't be cloned. And yes, we're
relying on the compiler treating all pointers equally, even though
a strict C program cannot portably do so - but we're not the first
one in the qemu code base to expect it to work (hello, glib!).
The choice of adding a fourth visitor type deserves some explanation.
On the surface, the clone visitor is mostly an input visitor (it
takes arbitrary input - in this case, another QAPI object - and
creates a new QAPI object during the course of the visit). But
ever since commit da72ab0 consolidated enum visits based on the
visitor type, using VISITOR_INPUT would cause us to run
visit_type_str(), even though for cloning there is nothing to do
(we just copy the enum value across, without regards to its mapping
to strings). Also, since our input happens to be a QAPI object,
we can also satisfy the internal checks for VISITOR_OUTPUT. So in
the end, I settled with a new VISITOR_CLONE, and chose its value
such that many internal checks can use 'v->type & mask', sticking
to 'v->type == value' where the difference matters.
Note that we can only clone objects (including alternates) and lists,
not built-ins or enums. The visitor core hides integer width from
the actual visitor (since commit 04e070d), and as long as that's the
case, we can't clone top-level integers. Then again, those can
always be cloned by direct copy, since they are not objects with
deep pointers, so it's no real loss. And restricting cloning to
just objects and lists is cleaner than restricting it to non-integers.
As such, I documented that the clone visitor is for direct use only
by code internal to QAPI, and should not be used on incomplete objects
(other than a hack to work around the fact that we allow NULL in place
of "" in visit_type_str() in other output visitors). Note that as
written, the clone visitor will never fail on a complete object.
Scalars (including enums) not at the root of the clone copy just fine
with no additional effort while visiting the scalar, by virtue of a
g_memdup() each time we push another struct onto the stack. Cloning
a string requires deduplication of a pointer, which means it can also
provide the guarantee of an input visitor of never producing NULL
even when still accepting NULL in place of "" the way the QMP output
visitor does.
Cloning an 'any' type could be possible by incrementing the QObject
refcnt, but it's not obvious whether that is better than implementing
a QObject deep clone. So for now, we document it as unsupported,
and intentionally omit the .type_any() callback to let a developer
know their usage needs implementation.
Add testsuite coverage for several different clone situations, to
ensure that the code is working. I also tested that valgrind was
happy with the test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-14-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Making each output visitor provide its own output collection
function was the only remaining reason for exposing visitor
sub-types to the rest of the code base. Add a polymorphic
visit_complete() function which is a no-op for input visitors,
and which populates an opaque pointer for output visitors. For
maximum type-safety, also add a parameter to the output visitor
constructors with a type-correct version of the output pointer,
and assert that the two uses match.
This approach was considered superior to either passing the
output parameter only during construction (action at a distance
during visit_free() feels awkward) or only during visit_complete()
(defeating type safety makes it easier to use incorrectly).
Most callers were function-local, and therefore a mechanical
conversion; the testsuite was a bit trickier, but the previous
cleanup patch minimized the churn here.
The visit_complete() function may be called at most once; doing
so lets us use transfer semantics rather than duplication or
ref-count semantics to get the just-built output back to the
caller, even though it means our behavior is not idempotent.
Generated code is simplified as follows for events:
|@@ -26,7 +26,7 @@ void qapi_event_send_acpi_device_ost(ACP
| QDict *qmp;
| Error *err = NULL;
| QMPEventFuncEmit emit;
|- QmpOutputVisitor *qov;
|+ QObject *obj;
| Visitor *v;
| q_obj_ACPI_DEVICE_OST_arg param = {
| info
|@@ -39,8 +39,7 @@ void qapi_event_send_acpi_device_ost(ACP
|
| qmp = qmp_event_build_dict("ACPI_DEVICE_OST");
|
|- qov = qmp_output_visitor_new();
|- v = qmp_output_get_visitor(qov);
|+ v = qmp_output_visitor_new(&obj);
|
| visit_start_struct(v, "ACPI_DEVICE_OST", NULL, 0, &err);
| if (err) {
|@@ -55,7 +54,8 @@ void qapi_event_send_acpi_device_ost(ACP
| goto out;
| }
|
|- qdict_put_obj(qmp, "data", qmp_output_get_qobject(qov));
|+ visit_complete(v, &obj);
|+ qdict_put_obj(qmp, "data", obj);
| emit(QAPI_EVENT_ACPI_DEVICE_OST, qmp, &err);
and for commands:
| {
| Error *err = NULL;
|- QmpOutputVisitor *qov = qmp_output_visitor_new();
| Visitor *v;
|
|- v = qmp_output_get_visitor(qov);
|+ v = qmp_output_visitor_new(ret_out);
| visit_type_AddfdInfo(v, "unused", &ret_in, &err);
|- if (err) {
|- goto out;
|+ if (!err) {
|+ visit_complete(v, ret_out);
| }
|- *ret_out = qmp_output_get_qobject(qov);
|-
|-out:
| error_propagate(errp, err);
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
qmp_output_visitor_cleanup(); however, we still need to
expose the subtype for qmp_output_get_qobject().
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-10-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
string_output_visitor_cleanup(); however, we still need to
expose the subtype for string_output_get_string().
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-9-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
qmp_input_visitor_cleanup(); which in turn means we no longer
need to return a subtype from qmp_input_visitor_new() nor a
public upcast function.
Generated code changes to qmp-marshal.c look like:
|@@ -52,11 +52,10 @@ void qmp_marshal_add_fd(QDict *args, QOb
| {
| Error *err = NULL;
| AddfdInfo *retval;
|- QmpInputVisitor *qiv = qmp_input_visitor_new(QOBJECT(args), true);
| Visitor *v;
| q_obj_add_fd_arg arg = {0};
|
|- v = qmp_input_get_visitor(qiv);
|+ v = qmp_input_visitor_new(QOBJECT(args), true);
| visit_start_struct(v, NULL, NULL, 0, &err);
| if (err) {
| goto out;
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-8-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
string_input_visitor_cleanup(); which in turn means we no longer
need to return a subtype from string_input_visitor_new() nor a
public upcast function.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-7-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
opts_visitor_cleanup(); which in turn means we no longer need
to return a subtype from opts_visitor_new() nor a public upcast
function.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-6-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Making each visitor provide its own (awkwardly-named) FOO_cleanup()
is unusual, when we can instead have a polymorphic visit_free()
interface. Over the next few patches, we can use the polymorphic
functions to eliminate the need for a FOO_get_visitor() function
for accessing specific visitor functionality, once everything can
be accessed directly through the Visitor* interfaces.
The dealloc visitor is the first one converted to completely use
the new entry point, since qapi_dealloc_visitor_cleanup() was the
only reason that qapi_dealloc_get_visitor() existed, and only
generated and testsuite code was even using it. With the new
visit_free() entry point in place, we no longer need to expose
the QapiDeallocVisitor subtype through qapi_dealloc_visitor_new(),
and can get by with less generated code, with diffs that look like:
| void qapi_free_ACPIOSTInfo(ACPIOSTInfo *obj)
| {
|- QapiDeallocVisitor *qdv;
| Visitor *v;
|
| if (!obj) {
| return;
| }
|
|- qdv = qapi_dealloc_visitor_new();
|- v = qapi_dealloc_get_visitor(qdv);
|+ v = qapi_dealloc_visitor_new();
| visit_type_ACPIOSTInfo(v, NULL, &obj, NULL);
|- qapi_dealloc_visitor_cleanup(qdv);
|+ visit_free(v);
|}
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-5-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Rather than making the dealloc visitor track of stack of pointers
remembered during visit_start_* in order to free them during
visit_end_*, it's a lot easier to just make all callers pass the
same pointer to visit_end_*. The generated code has access to the
same pointer, while all other users are doing virtual walks and
can pass NULL. The dealloc visitor is then greatly simplified.
All three visit_end_*() functions intentionally take a void**,
even though the visit_start_*() functions differ between void**,
GenericList**, and GenericAlternate**. This is done for several
reasons: when doing a virtual walk, passing NULL doesn't care
what the type is, but when doing a generated walk, we already
have to cast the caller's specific FOO* to call visit_start,
while using void** lets us use visit_end without a cast. Also,
an upcoming patch will add a clone visitor that wants to use
the same implementation for all three visit_end callbacks,
which is made easier if all three share the same signature.
For visitors with already track per-object state (the QMP visitors
via a stack, and the string visitors which do not allow nesting),
add an assertion that the caller is indeed passing the same
pointer to paired calls.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-4-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
'qjson.h' is not a QObject subtype; include this file directly in
.c files that are using it, rather than abusing qmp/types.h for
that purpose.
Meanwhile, for files that include a list of individual QObject
subtypes, it's easier to just use qmp/types.h for that purpose.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-2-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Spice client needs the whole GL texture dimension to be able to show a
scanout with a monitor offset (different than +0+0).
Furthermore, this fixes a crash when calling surface_{width,height}()
after dpy_gfx_replace_surface(con, NULL) was called in
virgl_cmd_set_scanout()
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1465911849-30423-4-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In virgl_cmd_resource_flush(), when several consoles are updated, it
needs to keep blocking until all spice gl draws are done. This fixes an
assert() in spice when using multiple monitors with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1465911849-30423-2-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Spice deprecated this callback in 0.12.6.
It's not a problem yet, but it will cause Clang to fail in a -Werror
build due to the deprecated tag.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1467240095-12507-2-git-send-email-jsnow@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some architectures (e.g. ARMv8) need the address which is aligned
to a size more than the size of the memory access.
To support such check it's enough the current costless alignment
check implementation in QEMU, but we need to support
an alignment size specifying.
Signed-off-by: Sergey Sorokin <afarallax@yandex.ru>
Message-Id: <1466705806-679898-1-git-send-email-afarallax@yandex.ru>
Signed-off-by: Richard Henderson <rth@twiddle.net>
[rth: Assert in tcg_canonicalize_memop. Leave get_alignment_bits
available for, though unused by, user-mode. Retain logging difference
based on ALIGNED_ONLY.]
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXe4l4AAoJECgfDbjSjVRpIz4IALye7mKG61/POA4Gqmhalc3d
HnlNSZ2YcKAuvPg7WWkBuRacrQvVY/MbW1mLloG1lY0tdFgZG8Cy+CY6wJg1NE4c
cXd+77vHkIyrnl+Nil+QOgTFiAsMnD+mXHHsnCDw2jGn3JbgVNuCMi7V34fGkQd2
PDkZyYfwTqO3HytuG0/j2Somc9du1gjYdn+9qigfZVgP96jGDojBuJWuuU5flCB3
Kj5xrOuI01XlbdTk71tVjBJBektQurWr6r7GECDqZIpUfc+BI70FU9jPh+OlLTO/
92yi29ncjyStz4tRnf18xoQ8uBgH/tD1xigEUPRtnm1+0i/tgONBL8cAdBF9FBE=
=ABGE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
iommus can not be added with -device.
cleanups and fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Jul 2016 11:18:32 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (30 commits)
vmw_pvscsi: remove unnecessary internal msi state flag
e1000e: remove unnecessary internal msi state flag
vmxnet3: remove unnecessary internal msi state flag
mptsas: remove unnecessary internal msi state flag
megasas: remove unnecessary megasas_use_msi()
pci: Convert msi_init() to Error and fix callers to check it
pci bridge dev: change msi property type
megasas: change msi/msix property type
mptsas: change msi property type
intel-hda: change msi property type
usb xhci: change msi/msix property type
change pvscsi_init_msi() type to void
tests: add APIC.cphp and DSDT.cphp blobs
tests: acpi: add CPU hotplug testcase
log: Permit -dfilter 0..0xffffffffffffffff
range: Replace internal representation of Range
range: Eliminate direct Range member access
log: Clean up misuse of Range for -dfilter
pci_register_bar: cleanup
Revert "virtio-net: unbreak self announcement and guest offloads after migration"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the final patch for converting the common I/O path to take
a BdrvChild parameter instead of BlockDriverState.
The completion of this conversion means that all users that perform I/O
on an image need to actually hold a reference (in the form of BdrvChild,
possible as part of a BlockBackend) to that image. This also protects
against inconsistent use of BlockBackend vs. BlockDriverState functions
because direct use of a BlockDriverState isn't possible any more and
blk->root is private for block-backends.c.
In addition, we can now distinguish different users in the I/O path,
and the future op blockers work is going to add assertions based on
permissions stored in BdrvChild.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Using int for values that are only used as booleans is confusing.
While at it, rearrange a couple of members so that all the bools
are contiguous.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It makes more sense to have ALL block size limit constraints
in the same struct. Improve the documentation while at it.
Simplify a couple of conditionals, now that we have audited and
documented that request_alignment is always non-zero.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_discard and
discard_alignment. Rename them, using 'pdiscard' as an aid to
track which remaining discard interfaces need conversion, and so
that the compiler will help us catch the change in semantics
across any rebased code. The BlockLimits type is now completely
byte-based; and in iscsi.c, sector_limits_lun2qemu() is no
longer needed.
pdiscard_alignment is made unsigned (we use power-of-2 alignments
as bitmasks, where unsigned is easier to think about) while
leaving max_pdiscard signed (since we still have an 'int'
interface); this is comparable to what commit cf081fc did for
write zeroes limits. We may later want to make everything an
unsigned 64-bit limit - but that requires a bigger code audit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Improve the documentation of the write zeroes limits, to mention
additional constraints that drivers should observe. Worth squashing
into commit cf081fca, if that hadn't been pushed already :)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_transfer_length
and opt_transfer_length. Rename them (dropping the _length suffix)
so that the compiler will help us catch the change in semantics
across any rebased code, and improve the documentation. Use unsigned
values, so that we don't have to worry about negative values and
so that bit-twiddling is easier; however, we are still constrained
by 2^31 of signed int in most APIs.
When a value comes from an external source (iscsi and raw-posix),
sanitize the results to ensure that opt_transfer is a power of 2.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The NBD layer was breaking up request at a limit of 2040 sectors
(just under 1M) to cater to old qemu-nbd. But the server limit
was raised to 32M in commit 2d8214885 to match the kernel, more
than three years ago; and the upstream NBD Protocol is proposing
documentation that without any explicit communication to state
otherwise, a client should be able to safely assume that a 32M
transaction will work. It is time to rely on the larger sizing,
and any downstream distro that cares about maximum
interoperability to older qemu-nbd servers can just tweak the
value of #define NBD_MAX_SECTORS.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
msi_init() reports errors with error_report(), which is wrong
when it's used in realize().
Fix by converting it to Error.
Fix its callers to handle failure instead of ignoring it.
For those callers who don't handle the failure, it might happen:
when user want msi on, but he doesn't get what he want because of
msi_init fails silently.
cc: Gerd Hoffmann <kraxel@redhat.com>
cc: John Snow <jsnow@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Hannes Reinecke <hare@suse.de>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Alex Williamson <alex.williamson@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
This adds support for Dynamic DMA Windows (DDW) option defined by
the SPAPR specification which allows to have additional DMA window(s)
The "ddw" property is enabled by default on a PHB but for compatibility
the pseries-2.6 machine and older disable it.
This also creates a single DMA window for the older machines to
maintain backward migration.
This implements DDW for PHB with emulated and VFIO devices. The host
kernel support is required. The advertised IOMMU page sizes are 4K and
64K; 16M pages are supported but not advertised by default, in order to
enable them, the user has to specify "pgsz" property for PHB and
enable huge pages for RAM.
The existing linux guests try creating one additional huge DMA window
with 64K or 16MB pages and map the entire guest RAM to. If succeeded,
the guest switches to dma_direct_ops and never calls TCE hypercalls
(H_PUT_TCE,...) again. This enables VFIO devices to use the entire RAM
and not waste time on map/unmap later. This adds a "dma64_win_addr"
property which is a bus address for the 64bit window and by default
set to 0x800.0000.0000.0000 as this is what the modern POWER8 hardware
uses and this allows having emulated and VFIO devices on the same bus.
This adds 4 RTAS handlers:
* ibm,query-pe-dma-window
* ibm,create-pe-dma-window
* ibm,remove-pe-dma-window
* ibm,reset-pe-dma-window
These are registered from type_init() callback.
These RTAS handlers are implemented in a separate file to avoid polluting
spapr_iommu.c with PCI.
This changes sPAPRPHBState::dma_liobn to an array to allow 2 LIOBNs
and updates all references to dma_liobn. However this does not add
64bit LIOBN to the migration stream as in fact even 32bit LIOBN is
rather pointless there (as it is a PHB property and the management
software can/should pass LIOBNs via CLI) but we keep it for the backward
migration support.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
New VFIO_SPAPR_TCE_v2_IOMMU type supports dynamic DMA window management.
This adds ability to VFIO common code to dynamically allocate/remove
DMA windows in the host kernel when new VFIO container is added/removed.
This adds a helper to vfio_listener_region_add which makes
VFIO_IOMMU_SPAPR_TCE_CREATE ioctl and adds just created IOMMU into
the host IOMMU list; the opposite action is taken in
vfio_listener_region_del.
When creating a new window, this uses heuristic to decide on the TCE table
levels number.
This should cause no guest visible change in behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added some casts to prevent printf() warnings on certain targets
where the kernel headers' __u64 doesn't match uint64_t or PRIx64]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are going to be multiple IOMMUs per a container. This moves
the single host IOMMU parameter set to a list of VFIOHostDMAWindow.
This should cause no behavioral change and will be used later by
the SPAPR TCE IOMMU v2 which will also add a vfio_host_win_del() helper.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes use of the new "memory registering" feature. The idea is
to provide the userspace ability to notify the host kernel about pages
which are going to be used for DMA. Having this information, the host
kernel can pin them all once per user process, do locked pages
accounting (once) and not spent time on doing that in real time with
possible failures which cannot be handled nicely in some cases.
This adds a prereg memory listener which listens on address_space_memory
and notifies a VFIO container about memory which needs to be
pinned/unpinned. VFIO MMIO regions (i.e. "skip dump" regions) are skipped.
The feature is only enabled for SPAPR IOMMU v2. The host kernel changes
are required. Since v2 does not need/support VFIO_IOMMU_ENABLE, this does
not call it when v2 is detected and enabled.
This enforces guest RAM blocks to be host page size aligned; however
this is not new as KVM already requires memory slots to be host page
size aligned.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Fix compile error on 32-bit host]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The gnutls default priority is either "NORMAL" (most historical
versions of gnutls) which is a built-in label in gnutls code,
or "@SYSTEM" (latest gnutls on Fedora at least) which refers
to an admin customizable entry in a gnutls config file.
Regardless of which default is used by a distro, they are both
global defaults applying to all applications using gnutls. If
a single application on the system needs to use a weaker set
of crypto priorities, this potentially forces the weakness onto
all applications. Or conversely if a single application wants a
strong default than all others, it can't do this via the global
config file.
This adds an extra parameter to the tls credential object which
allows the mgmt app / user to explicitly provide a priority
string to QEMU when configuring TLS.
For example, to use the "NORMAL" priority, but disable SSL 3.0
one can now configure QEMU thus:
$QEMU -object tls-creds-x509,id=tls0,dir=/home/berrange/qemutls,\
priority="NORMAL:-VERS-SSL3.0" \
..other args...
If creating tls-creds-anon, whatever priority the user specifies
will always have "+ANON-DH" appended to it, since that's mandatory
to make the anonymous credentials work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Range represents a range as follows. Member @start is the inclusive
lower bound, member @end is the exclusive upper bound. Zero @end is
special: if @start is also zero, the range is empty, else @end is to
be interpreted as 2^64. No other empty ranges may occur.
The range [0,2^64-1] cannot be represented. If you try to create it
with range_set_bounds1(), you get the empty range instead. If you try
to create it with range_set_bounds() or range_extend(), assertions
fail. Before range_set_bounds() existed, the open-coded creation
usually got you the empty range instead. Open deathtrap.
Moreover, the code dealing with the janus-faced @end is too clever by
half.
Dumb this down to a more pedestrian representation: members @lob and
@upb are inclusive lower and upper bounds. The empty range is encoded
as @lob = 1, @upb = 0.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Users of struct Range mess liberally with its members, which makes
refactoring hard. Create a set of methods, and convert all users to
call them instead of accessing members. The methods have carefully
worded contracts, and use assertions to check them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a minimal model for the devcfg device which is part of Zynq.
This model supports DMA capabilities and interrupt generation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 83df49d8fa2d203a421ca71620809e4b04754e65.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a helper that will scan a static RegisterAccessInfo Array
and populate a container MemoryRegion with registers as defined.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 347b810b2799e413c98d5bbeca97bcb1557946c3.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QOMify registers as a child of TYPE_DEVICE. This allows registers to
define GPIOs.
Define an init helper that will do QOM initialisation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2545f71db26bf5586ca0c08a3e3cf1b217450552.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define some macros that can be used for defining registers and fields.
The REG32 macro will define A_FOO, for the byte address of a register
as well as R_FOO for the uint32_t[] register number (A_FOO / 4).
The FIELD macro will define FOO_BAR_MASK, FOO_BAR_SHIFT and
FOO_BAR_LENGTH constants for field BAR in register FOO.
Finally, there are some shorthand helpers for extracting/depositing
fields from registers based on these naming schemes.
Usage can greatly reduce the verbosity of device code.
The deposit and extract macros (eg FIELD_EX32, FIELD_DP32 etc.) can be
used to generate extract and deposits without any repetition of the name
stems.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: bbd87a3c03b1f173b1ed73a6d502c0196c18a72f.1467053537.git.alistair.francis@xilinx.com
[ EI Changes:
* Add Deposit macros
]
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add memory io handlers that glue the register API to the memory API.
Just translation functions at this stage. Although it does allow for
devices to be created without all-in-one mmio r/w handlers.
This patch also adds the RegisterInfoArray struct, which allows all of
the individual RegisterInfo structs to be grouped into a single memory
region.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: f7704d8ac6ac0f469ed35401f8151a38bd01468b.1467053537.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This API provides some encapsulation of registers and factors out some
common functionality to common code. Bits of device state (usually MMIO
registers) often have all sorts of access restrictions and semantics
associated with them. This API allows you to define what those
restrictions are on a bit-by-bit basis.
Helper functions are then used to access the register which observe the
semantics defined by the RegisterAccessInfo struct.
Some features:
Bits can be marked as read_only (ro field)
Bits can be marked as write-1-clear (w1c field)
Bits can be marked as reserved (rsvd field)
Reset values can be defined (reset)
Bits can be marked clear on read (cor)
Pre and post action callbacks can be added to read and write ops
Verbose debugging info can be enabled/disabled
Useful for defining device register spaces in a data driven way. Cuts
down on a lot of the verbosity and repetition in the switch-case blocks
in the standard foo_mmio_read/write functions.
Also useful for automated generation of device models from hardware
design sources.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 40d62c7e1bf6e63bb4193ec46b15092a7d981e59.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a macro that creates a 64bit value which has length number of ones
shifted across by the value of shift.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 9773244aa1c8c26b8b82cb261d8f5dd4b7b9fcf9.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It doesn't make sense to pass a NULL ops argument to
memory_region_init_rom_device(), because the effect will
be that if the guest tries to write to the memory region
then QEMU will segfault. Catch the bug earlier by sanity
checking the arguments to this function, and remove the
misleading documentation that suggests that passing NULL
might be sensible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-4-git-send-email-peter.maydell@linaro.org
Provide a new helper function memory_region_init_rom() for memory
regions which are read-only (and unlike those created by
memory_region_init_rom_device() don't have special behaviour
for writes). This has the same behaviour as calling
memory_region_init_ram() and then memory_region_set_readonly()
(which is what we do today in boards with pure ROMs) but is a
more easily discoverable API for the purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1467122287-24974-2-git-send-email-peter.maydell@linaro.org
PcPciInfo has two (ill-named) members: Range w32 is the PCI hole, and
w64 is the PCI64 hole.
Three users:
* I440FXState and MCHPCIState have a member PcPciInfo pci_info, but
only pci_info.w32 is actually used. This is confusing. Replace by
Range pci_hole.
* acpi_build() uses auto PcPciInfo pci_info to forward both PCI holes
from acpi_get_pci_info() to build_dsdt(). Replace by two variables
Range pci_hole, pci_hole64. Rename acpi_get_pci_info() to
acpi_get_pci_holes().
PcPciInfo is now unused; drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Since iommu devices can be created with '-device' there is
no need to keep iommu as machine and mch property.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Skip bus_master_enable region creation on PCI device init
in order to be sure the IOMMU device (if present) would
be created in advance. Add this memory region at machine_done time.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here's the current ppc patch queue. This is a fairly large batch,
containing:
* A number of further preliminary patches towards full hypervisor
mode emulation
* Some further fixes / cleanups for the recently merged device_add
based CPU hotplug
* Preliminary patches towards supporting a native (rather than
paravirtualized) XICS device. This will be needed to emulate a
physical Power machine, including hypervisor capabilities
* Assorted bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KhVy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160701' into staging
ppc patch queue 2016-07-01
Here's the current ppc patch queue. This is a fairly large batch,
containing:
* A number of further preliminary patches towards full hypervisor
mode emulation
* Some further fixes / cleanups for the recently merged device_add
based CPU hotplug
* Preliminary patches towards supporting a native (rather than
paravirtualized) XICS device. This will be needed to emulate a
physical Power machine, including hypervisor capabilities
* Assorted bug fixes
# gpg: Signature made Fri 01 Jul 2016 06:56:35 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160701: (23 commits)
qmp: fix spapr example of query-hotpluggable-cpus
spapr: drop duplicate variable in spapr_core_release()
spapr: do proper error propagation in spapr_cpu_core_realize_child()
spapr: drop reference on child object during core realization
spapr: Restore support for 970MP and POWER8NVL CPU cores
target-ppc: gen_pause for instructions: yield, mdoio, mdoom, miso
ppc/xics: Replace "icp" with "xics" in most places
ppc/xics: Implement H_IPOLL using an accessor
ppc/xics: Move SPAPR specific code to a separate file
ppc/xics: Rename existing xics to xics_spapr
ppc: Fix 64K pages support in full emulation
target-ppc: Eliminate redundant and incorrect function booke206_page_size_to_tlb
spapr: Restore support for older PowerPC CPU cores
spapr: fix write-past-end-of-array error in cpu core device init code
hw/ppc/spapr: Add some missing hcall function set strings
ppc: Print HSRR0/HSRR1 in "info registers"
ppc: LPCR is a HV resource
ppc: Initial HDEC support
ppc: Enforce setting MSR:EE,IR and DR when MSR:PR is set
ppc: Fix conditions for delivering external interrupts to a guest
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "ICP" is a different object than the "XICS". For historical reasons,
we have a number of places where we name a variable "icp" while it contains
a XICSState pointer. There *is* an ICPState structure too so this makes
the code really confusing.
This is a mechanical replacement of all those instances to use the name
"xics" instead. There should be no functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[spapr_cpu_init has been moved to spapr_cpu_core.c, change there]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
None of the other presenter functions directly mucks with the
internal state, so don't do it there either.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The common class doesn't change, the KVM one is sPAPR specific. Rename
variables and functions to xics_spapr.
Retain the type name as "xics" to preserve migration for existing sPAPR
guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The IOMMU driver may change behavior depending on whether a notifier
client is present. In the case of POWER, this represents a change in
the visibility of the IOTLB, for other drivers such as intel-iommu and
future AMD-Vi emulation, notifier support is not yet enabled and this
provides the opportunity to flag that incompatibility.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Xu <peterx@redhat.com>
Tested-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[new log & extracted from [PATCH qemu v17 12/12] spapr_iommu, vfio, memory: Notify IOMMU about starting/stopping listening]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The link property that was added to the pcspk device has the wrong type:
it is only correct for TCG and for KVM's userspace or split irqchip
options. The default KVM option (fully in-kernel irqchip) breaks
because it uses a PIT whose type is a sibling of TYPE_I8254.
Fixes: 873b4d3f05
Tested-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1467298657-6588-1-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling our function g_list_insert_sorted_merged is a misnomer,
since we are NOT writing a glib function. Furthermore, we are
making every caller pass the same comparator function of
range_merge(): any caller that would try otherwise would break
in weird ways since our internal call to ranges_can_merge() is
hard-coded to operate only on ranges, rather than paying
attention to the caller's comparator.
Better is to fix things so that callers don't have to care about
our internal comparator, by picking a function name and updating
the parameter type away from a gratuitous use of void*, to make
it obvious that we are operating specifically on a list of ranges
and not a generic list. Plus, refactoring the code here will
make it easier to plug a memory leak in the next patch.
range_compare() is now internal only, and moves to the .c file.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1464712890-14262-3-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
g_list_insert_sorted_merged() is rather large to be an inline
function; move it to its own file. range_merge() and
ranges_can_merge() can likewise move, as they are only used
internally. Also, it becomes obvious that the condition within
range_merge() is already satisfied by its caller, and that the
return value is not used.
The diffstat is misleading, because of the copyright boilerplate.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1464712890-14262-2-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
qemu leaves unix socket files behind when removing a listening chardev
or leaving. qemu could clean that up, even if doing so isn't race-free.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1347077
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1466105332-10285-4-git-send-email-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Otherwise, this can cause serial_xmit to be entered with LSR.TEMT=0,
which is invalid and causes an assertion failure.
Reported-by: Bret Ketchum <bcketchum@gmail.com>
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
g_source_attach can return any value between 1 and UINT_MAX if you let
QEMU run long enough. However, qemu_chr_fe_add_watch can also return
a negative errno value when the device is disconnected or does not
support chr_add_watch. Change it to return zero to avoid overloading
these values.
Fix the cadence_uart which asserts in this case (easily obtained with
"-serial pty").
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It can never become negative; reflect this in the type of the field
and simplify the conditions.
Tested-by: Bret Ketchum <bcketchum@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function needs to be converted to QOM hook and virtualised for
multi-arch. This rename interferes, as cpu-qom will not have access
to the renaming causing name divergence. This rename doesn't really do
anything anyway so just delete it.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-Id: <69bd25a8678b8b31b91cd9760c777bed1aafb44e.1437212383.git.crosthwaite.peter@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Crosthwaite <crosthwaitepeter@gmail.com>
Commit 926cde5 ("scsi: esp: make cmdbuf big enough for maximum CDB size",
2016-06-16) changed the size of a migrated field. Split it in two
parts, and only migrate the second part in a new vmstate version.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently a direct access to the device structure field is used to connect ISA
device IRQ to the bus. GPIO access should be used instead if possible.
The patch adds wrapper isa_connect_gpio_out. The function connects specified
output GPIO to specified ISA IRQ.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ICH9 LPC bridge has 24 output IRQs connected to GSI. Currently the IRQs are
referenced by pointers. The pointers are initialized at startup by direct access
to the structure fields. This violates Qemu device model.
The patch makes the IRQs handling to use GPIO model.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ich9->pic and ich9->ioapic differ for the first 16 GSIs (because
ich9->pic is wired to 8259+IOAPIC but ich9->ioapic is wired to
IOAPIC only). However, ich9->ioapic is never used for the first
16 GSIs, so the two vectors can be merged.
Reviewed-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ICH9 SMB bridge can be created using qdev API despite existence of helper
function. The type name is needed for such creation. Using a preprocessor
alias instead the string type name itself is preferable.
The patch makes the alias accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The port92 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The
pointer is never changed at runtime. Hence, common GPIO model can be applied
to A20 IRQ line. Note that checking for IRQ to be connected as in
previous version of code is not required qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The i8042 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The pointer
is never changed at runtime. So common GPIO model can be applied to A20 IRQ
line. Note that checking for IRQ to be connected as in previous version
of code is not required because qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During creation of Q35 instance several parameters are set using direct access.
It violates Qemu device model. Correctly, the parameters should be handled as
object properties.
The patch adds four link type properties for fields:
mch.ram_memory
mch.pci_address_space
mch.system_memory
mch.address_space_io
And, it adds two size type properties for fields:
mch.below_4g_mem_size
mch.above_4g_mem_size
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev API can be used to create CFI pflash devices despite existance of helper
functions. The type name is needed in course of such creation. Using the
preprocessor alias instead of the string literal itself is preferable.
The patch makes the aliases accessible through the header.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently vmport device is identified by the string literal. Using a
preprocessor alias instead is preferable.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The speaker device needs pointer to ISA PIT device to operate. But according to
qdev-properties.h, properties of pointer type should be avoided. It seems a
link type property is a good substitution.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Multiqueue virtio-blk can be enabled as follows:
qemu -device virtio-blk-pci,num-queues=8
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-8-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Multiqueue requires that each request knows to which virtqueue it
belongs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-5-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The num_queues field is always 1 for the time being. A later patch will
make it a configurable device property so that multiqueue can be
enabled.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466511196-12612-2-git-send-email-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use socket_*() functions from include/qemu/sockets.h instead of
listen()/bind()/connect()/parse_host_port(). socket_*() fucntions are
QAPI based and this patch performs this api conversion since
everything will be using QAPI based sockets in the future. Also add a
helper function socket_address_to_string() in util/qemu-sockets.c
which returns the string representation of socket address. Thetask was
listed on http://wiki.qemu.org/BiteSizedTasks page.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
By specifying the silicon revision we select the appropriate reset
values for the SoC.
Additionally, expose hardware strapping properties aliasing those
provided by the SCU for board-specific configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466744305-23163-3-git-send-email-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Small queue this time. Main reason for sending it is the pair of
patches to fix up the new cpu hotplug model used on Power to what
should be an actually usable state. There's also a small BookE bugfix
and a XICS trivial cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ltJi
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160627' into staging
ppc patch queue for 2016-06-27
Small queue this time. Main reason for sending it is the pair of
patches to fix up the new cpu hotplug model used on Power to what
should be an actually usable state. There's also a small BookE bugfix
and a XICS trivial cleanup.
# gpg: Signature made Mon 27 Jun 2016 06:28:37 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160627:
qapi: keep names in 'CpuInstanceProperties' in sync with struct CPUCore
qapi: Report support for -device cpu hotplug in query-machines
ppc/xics: Remove unused xics_set_irq_type()
target-ppc: ppce500_spin.c uses SPR_PIR, should use SPR_BOOKE_PIR
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
