qemu-patch-raspberry4/hw/riscv/sifive_u.c
Bin Meng 623d53cb01 hw/riscv: sifive_u: Make sure firmware info is 8-byte aligned
Currently the firmware dynamic info (fw_dyn) is put right after
the reset vector, which is not 8-byte aligned on RV64. OpenSBI
fw_dynamic uses ld to read contents from 'struct fw_dynamic_info',
which expects fw_dyn to be on the 8-byte boundary, otherwise the
misaligned load exception may happen. Fortunately this does not
cause any issue on QEMU, as QEMU does support misaligned load.

RV32 does not have any issue as it is 4-byte aligned already.
Change to make sure it is 8-byte aligned which works for both
RV32 and RV64.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210708143319.10441-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
2021-07-15 08:56:00 +10:00

959 lines
39 KiB
C

/*
* QEMU RISC-V Board Compatible with SiFive Freedom U SDK
*
* Copyright (c) 2016-2017 Sagar Karandikar, sagark@eecs.berkeley.edu
* Copyright (c) 2017 SiFive, Inc.
* Copyright (c) 2019 Bin Meng <bmeng.cn@gmail.com>
*
* Provides a board compatible with the SiFive Freedom U SDK:
*
* 0) UART
* 1) CLINT (Core Level Interruptor)
* 2) PLIC (Platform Level Interrupt Controller)
* 3) PRCI (Power, Reset, Clock, Interrupt)
* 4) GPIO (General Purpose Input/Output Controller)
* 5) OTP (One-Time Programmable) memory with stored serial number
* 6) GEM (Gigabit Ethernet Controller) and management block
* 7) DMA (Direct Memory Access Controller)
* 8) SPI0 connected to an SPI flash
* 9) SPI2 connected to an SD card
*
* This board currently generates devicetree dynamically that indicates at least
* two harts and up to five harts.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "qemu/osdep.h"
#include "qemu/error-report.h"
#include "qapi/error.h"
#include "qapi/visitor.h"
#include "hw/boards.h"
#include "hw/irq.h"
#include "hw/loader.h"
#include "hw/sysbus.h"
#include "hw/char/serial.h"
#include "hw/cpu/cluster.h"
#include "hw/misc/unimp.h"
#include "hw/ssi/ssi.h"
#include "target/riscv/cpu.h"
#include "hw/riscv/riscv_hart.h"
#include "hw/riscv/sifive_u.h"
#include "hw/riscv/boot.h"
#include "hw/char/sifive_uart.h"
#include "hw/intc/sifive_clint.h"
#include "hw/intc/sifive_plic.h"
#include "chardev/char.h"
#include "net/eth.h"
#include "sysemu/arch_init.h"
#include "sysemu/device_tree.h"
#include "sysemu/runstate.h"
#include "sysemu/sysemu.h"
#include <libfdt.h>
/* CLINT timebase frequency */
#define CLINT_TIMEBASE_FREQ 1000000
static const MemMapEntry sifive_u_memmap[] = {
[SIFIVE_U_DEV_DEBUG] = { 0x0, 0x100 },
[SIFIVE_U_DEV_MROM] = { 0x1000, 0xf000 },
[SIFIVE_U_DEV_CLINT] = { 0x2000000, 0x10000 },
[SIFIVE_U_DEV_L2CC] = { 0x2010000, 0x1000 },
[SIFIVE_U_DEV_PDMA] = { 0x3000000, 0x100000 },
[SIFIVE_U_DEV_L2LIM] = { 0x8000000, 0x2000000 },
[SIFIVE_U_DEV_PLIC] = { 0xc000000, 0x4000000 },
[SIFIVE_U_DEV_PRCI] = { 0x10000000, 0x1000 },
[SIFIVE_U_DEV_UART0] = { 0x10010000, 0x1000 },
[SIFIVE_U_DEV_UART1] = { 0x10011000, 0x1000 },
[SIFIVE_U_DEV_QSPI0] = { 0x10040000, 0x1000 },
[SIFIVE_U_DEV_QSPI2] = { 0x10050000, 0x1000 },
[SIFIVE_U_DEV_GPIO] = { 0x10060000, 0x1000 },
[SIFIVE_U_DEV_OTP] = { 0x10070000, 0x1000 },
[SIFIVE_U_DEV_GEM] = { 0x10090000, 0x2000 },
[SIFIVE_U_DEV_GEM_MGMT] = { 0x100a0000, 0x1000 },
[SIFIVE_U_DEV_DMC] = { 0x100b0000, 0x10000 },
[SIFIVE_U_DEV_FLASH0] = { 0x20000000, 0x10000000 },
[SIFIVE_U_DEV_DRAM] = { 0x80000000, 0x0 },
};
#define OTP_SERIAL 1
#define GEM_REVISION 0x10070109
static void create_fdt(SiFiveUState *s, const MemMapEntry *memmap,
uint64_t mem_size, const char *cmdline, bool is_32_bit)
{
MachineState *ms = MACHINE(qdev_get_machine());
void *fdt;
int cpu;
uint32_t *cells;
char *nodename;
uint32_t plic_phandle, prci_phandle, gpio_phandle, phandle = 1;
uint32_t hfclk_phandle, rtcclk_phandle, phy_phandle;
static const char * const ethclk_names[2] = { "pclk", "hclk" };
static const char * const clint_compat[2] = {
"sifive,clint0", "riscv,clint0"
};
static const char * const plic_compat[2] = {
"sifive,plic-1.0.0", "riscv,plic0"
};
if (ms->dtb) {
fdt = s->fdt = load_device_tree(ms->dtb, &s->fdt_size);
if (!fdt) {
error_report("load_device_tree() failed");
exit(1);
}
goto update_bootargs;
} else {
fdt = s->fdt = create_device_tree(&s->fdt_size);
if (!fdt) {
error_report("create_device_tree() failed");
exit(1);
}
}
qemu_fdt_setprop_string(fdt, "/", "model", "SiFive HiFive Unleashed A00");
qemu_fdt_setprop_string(fdt, "/", "compatible",
"sifive,hifive-unleashed-a00");
qemu_fdt_setprop_cell(fdt, "/", "#size-cells", 0x2);
qemu_fdt_setprop_cell(fdt, "/", "#address-cells", 0x2);
qemu_fdt_add_subnode(fdt, "/soc");
qemu_fdt_setprop(fdt, "/soc", "ranges", NULL, 0);
qemu_fdt_setprop_string(fdt, "/soc", "compatible", "simple-bus");
qemu_fdt_setprop_cell(fdt, "/soc", "#size-cells", 0x2);
qemu_fdt_setprop_cell(fdt, "/soc", "#address-cells", 0x2);
hfclk_phandle = phandle++;
nodename = g_strdup_printf("/hfclk");
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", hfclk_phandle);
qemu_fdt_setprop_string(fdt, nodename, "clock-output-names", "hfclk");
qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
SIFIVE_U_HFCLK_FREQ);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "fixed-clock");
qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x0);
g_free(nodename);
rtcclk_phandle = phandle++;
nodename = g_strdup_printf("/rtcclk");
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", rtcclk_phandle);
qemu_fdt_setprop_string(fdt, nodename, "clock-output-names", "rtcclk");
qemu_fdt_setprop_cell(fdt, nodename, "clock-frequency",
SIFIVE_U_RTCCLK_FREQ);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "fixed-clock");
qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x0);
g_free(nodename);
nodename = g_strdup_printf("/memory@%lx",
(long)memmap[SIFIVE_U_DEV_DRAM].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
memmap[SIFIVE_U_DEV_DRAM].base >> 32, memmap[SIFIVE_U_DEV_DRAM].base,
mem_size >> 32, mem_size);
qemu_fdt_setprop_string(fdt, nodename, "device_type", "memory");
g_free(nodename);
qemu_fdt_add_subnode(fdt, "/cpus");
qemu_fdt_setprop_cell(fdt, "/cpus", "timebase-frequency",
CLINT_TIMEBASE_FREQ);
qemu_fdt_setprop_cell(fdt, "/cpus", "#size-cells", 0x0);
qemu_fdt_setprop_cell(fdt, "/cpus", "#address-cells", 0x1);
for (cpu = ms->smp.cpus - 1; cpu >= 0; cpu--) {
int cpu_phandle = phandle++;
nodename = g_strdup_printf("/cpus/cpu@%d", cpu);
char *intc = g_strdup_printf("/cpus/cpu@%d/interrupt-controller", cpu);
char *isa;
qemu_fdt_add_subnode(fdt, nodename);
/* cpu 0 is the management hart that does not have mmu */
if (cpu != 0) {
if (is_32_bit) {
qemu_fdt_setprop_string(fdt, nodename, "mmu-type", "riscv,sv32");
} else {
qemu_fdt_setprop_string(fdt, nodename, "mmu-type", "riscv,sv48");
}
isa = riscv_isa_string(&s->soc.u_cpus.harts[cpu - 1]);
} else {
isa = riscv_isa_string(&s->soc.e_cpus.harts[0]);
}
qemu_fdt_setprop_string(fdt, nodename, "riscv,isa", isa);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "riscv");
qemu_fdt_setprop_string(fdt, nodename, "status", "okay");
qemu_fdt_setprop_cell(fdt, nodename, "reg", cpu);
qemu_fdt_setprop_string(fdt, nodename, "device_type", "cpu");
qemu_fdt_add_subnode(fdt, intc);
qemu_fdt_setprop_cell(fdt, intc, "phandle", cpu_phandle);
qemu_fdt_setprop_string(fdt, intc, "compatible", "riscv,cpu-intc");
qemu_fdt_setprop(fdt, intc, "interrupt-controller", NULL, 0);
qemu_fdt_setprop_cell(fdt, intc, "#interrupt-cells", 1);
g_free(isa);
g_free(intc);
g_free(nodename);
}
cells = g_new0(uint32_t, ms->smp.cpus * 4);
for (cpu = 0; cpu < ms->smp.cpus; cpu++) {
nodename =
g_strdup_printf("/cpus/cpu@%d/interrupt-controller", cpu);
uint32_t intc_phandle = qemu_fdt_get_phandle(fdt, nodename);
cells[cpu * 4 + 0] = cpu_to_be32(intc_phandle);
cells[cpu * 4 + 1] = cpu_to_be32(IRQ_M_SOFT);
cells[cpu * 4 + 2] = cpu_to_be32(intc_phandle);
cells[cpu * 4 + 3] = cpu_to_be32(IRQ_M_TIMER);
g_free(nodename);
}
nodename = g_strdup_printf("/soc/clint@%lx",
(long)memmap[SIFIVE_U_DEV_CLINT].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_string_array(fdt, nodename, "compatible",
(char **)&clint_compat, ARRAY_SIZE(clint_compat));
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_CLINT].base,
0x0, memmap[SIFIVE_U_DEV_CLINT].size);
qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
cells, ms->smp.cpus * sizeof(uint32_t) * 4);
g_free(cells);
g_free(nodename);
nodename = g_strdup_printf("/soc/otp@%lx",
(long)memmap[SIFIVE_U_DEV_OTP].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "fuse-count", SIFIVE_U_OTP_REG_SIZE);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_OTP].base,
0x0, memmap[SIFIVE_U_DEV_OTP].size);
qemu_fdt_setprop_string(fdt, nodename, "compatible",
"sifive,fu540-c000-otp");
g_free(nodename);
prci_phandle = phandle++;
nodename = g_strdup_printf("/soc/clock-controller@%lx",
(long)memmap[SIFIVE_U_DEV_PRCI].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", prci_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "#clock-cells", 0x1);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
hfclk_phandle, rtcclk_phandle);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_PRCI].base,
0x0, memmap[SIFIVE_U_DEV_PRCI].size);
qemu_fdt_setprop_string(fdt, nodename, "compatible",
"sifive,fu540-c000-prci");
g_free(nodename);
plic_phandle = phandle++;
cells = g_new0(uint32_t, ms->smp.cpus * 4 - 2);
for (cpu = 0; cpu < ms->smp.cpus; cpu++) {
nodename =
g_strdup_printf("/cpus/cpu@%d/interrupt-controller", cpu);
uint32_t intc_phandle = qemu_fdt_get_phandle(fdt, nodename);
/* cpu 0 is the management hart that does not have S-mode */
if (cpu == 0) {
cells[0] = cpu_to_be32(intc_phandle);
cells[1] = cpu_to_be32(IRQ_M_EXT);
} else {
cells[cpu * 4 - 2] = cpu_to_be32(intc_phandle);
cells[cpu * 4 - 1] = cpu_to_be32(IRQ_M_EXT);
cells[cpu * 4 + 0] = cpu_to_be32(intc_phandle);
cells[cpu * 4 + 1] = cpu_to_be32(IRQ_S_EXT);
}
g_free(nodename);
}
nodename = g_strdup_printf("/soc/interrupt-controller@%lx",
(long)memmap[SIFIVE_U_DEV_PLIC].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells", 1);
qemu_fdt_setprop_string_array(fdt, nodename, "compatible",
(char **)&plic_compat, ARRAY_SIZE(plic_compat));
qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
qemu_fdt_setprop(fdt, nodename, "interrupts-extended",
cells, (ms->smp.cpus * 4 - 2) * sizeof(uint32_t));
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_PLIC].base,
0x0, memmap[SIFIVE_U_DEV_PLIC].size);
qemu_fdt_setprop_cell(fdt, nodename, "riscv,ndev", 0x35);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", plic_phandle);
plic_phandle = qemu_fdt_get_phandle(fdt, nodename);
g_free(cells);
g_free(nodename);
gpio_phandle = phandle++;
nodename = g_strdup_printf("/soc/gpio@%lx",
(long)memmap[SIFIVE_U_DEV_GPIO].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", gpio_phandle);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_TLCLK);
qemu_fdt_setprop_cell(fdt, nodename, "#interrupt-cells", 2);
qemu_fdt_setprop(fdt, nodename, "interrupt-controller", NULL, 0);
qemu_fdt_setprop_cell(fdt, nodename, "#gpio-cells", 2);
qemu_fdt_setprop(fdt, nodename, "gpio-controller", NULL, 0);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_GPIO].base,
0x0, memmap[SIFIVE_U_DEV_GPIO].size);
qemu_fdt_setprop_cells(fdt, nodename, "interrupts", SIFIVE_U_GPIO_IRQ0,
SIFIVE_U_GPIO_IRQ1, SIFIVE_U_GPIO_IRQ2, SIFIVE_U_GPIO_IRQ3,
SIFIVE_U_GPIO_IRQ4, SIFIVE_U_GPIO_IRQ5, SIFIVE_U_GPIO_IRQ6,
SIFIVE_U_GPIO_IRQ7, SIFIVE_U_GPIO_IRQ8, SIFIVE_U_GPIO_IRQ9,
SIFIVE_U_GPIO_IRQ10, SIFIVE_U_GPIO_IRQ11, SIFIVE_U_GPIO_IRQ12,
SIFIVE_U_GPIO_IRQ13, SIFIVE_U_GPIO_IRQ14, SIFIVE_U_GPIO_IRQ15);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,gpio0");
g_free(nodename);
nodename = g_strdup_printf("/gpio-restart");
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cells(fdt, nodename, "gpios", gpio_phandle, 10, 1);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "gpio-restart");
g_free(nodename);
nodename = g_strdup_printf("/soc/dma@%lx",
(long)memmap[SIFIVE_U_DEV_PDMA].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "#dma-cells", 1);
qemu_fdt_setprop_cells(fdt, nodename, "interrupts",
SIFIVE_U_PDMA_IRQ0, SIFIVE_U_PDMA_IRQ1, SIFIVE_U_PDMA_IRQ2,
SIFIVE_U_PDMA_IRQ3, SIFIVE_U_PDMA_IRQ4, SIFIVE_U_PDMA_IRQ5,
SIFIVE_U_PDMA_IRQ6, SIFIVE_U_PDMA_IRQ7);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_PDMA].base,
0x0, memmap[SIFIVE_U_DEV_PDMA].size);
qemu_fdt_setprop_string(fdt, nodename, "compatible",
"sifive,fu540-c000-pdma");
g_free(nodename);
nodename = g_strdup_printf("/soc/cache-controller@%lx",
(long)memmap[SIFIVE_U_DEV_L2CC].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_L2CC].base,
0x0, memmap[SIFIVE_U_DEV_L2CC].size);
qemu_fdt_setprop_cells(fdt, nodename, "interrupts",
SIFIVE_U_L2CC_IRQ0, SIFIVE_U_L2CC_IRQ1, SIFIVE_U_L2CC_IRQ2);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop(fdt, nodename, "cache-unified", NULL, 0);
qemu_fdt_setprop_cell(fdt, nodename, "cache-size", 2097152);
qemu_fdt_setprop_cell(fdt, nodename, "cache-sets", 1024);
qemu_fdt_setprop_cell(fdt, nodename, "cache-level", 2);
qemu_fdt_setprop_cell(fdt, nodename, "cache-block-size", 64);
qemu_fdt_setprop_string(fdt, nodename, "compatible",
"sifive,fu540-c000-ccache");
g_free(nodename);
nodename = g_strdup_printf("/soc/spi@%lx",
(long)memmap[SIFIVE_U_DEV_QSPI2].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_TLCLK);
qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_QSPI2_IRQ);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_QSPI2].base,
0x0, memmap[SIFIVE_U_DEV_QSPI2].size);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,spi0");
g_free(nodename);
nodename = g_strdup_printf("/soc/spi@%lx/mmc@0",
(long)memmap[SIFIVE_U_DEV_QSPI2].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop(fdt, nodename, "disable-wp", NULL, 0);
qemu_fdt_setprop_cells(fdt, nodename, "voltage-ranges", 3300, 3300);
qemu_fdt_setprop_cell(fdt, nodename, "spi-max-frequency", 20000000);
qemu_fdt_setprop_cell(fdt, nodename, "reg", 0);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "mmc-spi-slot");
g_free(nodename);
nodename = g_strdup_printf("/soc/spi@%lx",
(long)memmap[SIFIVE_U_DEV_QSPI0].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_TLCLK);
qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_QSPI0_IRQ);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_QSPI0].base,
0x0, memmap[SIFIVE_U_DEV_QSPI0].size);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,spi0");
g_free(nodename);
nodename = g_strdup_printf("/soc/spi@%lx/flash@0",
(long)memmap[SIFIVE_U_DEV_QSPI0].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "spi-rx-bus-width", 4);
qemu_fdt_setprop_cell(fdt, nodename, "spi-tx-bus-width", 4);
qemu_fdt_setprop(fdt, nodename, "m25p,fast-read", NULL, 0);
qemu_fdt_setprop_cell(fdt, nodename, "spi-max-frequency", 50000000);
qemu_fdt_setprop_cell(fdt, nodename, "reg", 0);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "jedec,spi-nor");
g_free(nodename);
phy_phandle = phandle++;
nodename = g_strdup_printf("/soc/ethernet@%lx",
(long)memmap[SIFIVE_U_DEV_GEM].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_string(fdt, nodename, "compatible",
"sifive,fu540-c000-gem");
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_GEM].base,
0x0, memmap[SIFIVE_U_DEV_GEM].size,
0x0, memmap[SIFIVE_U_DEV_GEM_MGMT].base,
0x0, memmap[SIFIVE_U_DEV_GEM_MGMT].size);
qemu_fdt_setprop_string(fdt, nodename, "reg-names", "control");
qemu_fdt_setprop_string(fdt, nodename, "phy-mode", "gmii");
qemu_fdt_setprop_cell(fdt, nodename, "phy-handle", phy_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_GEM_IRQ);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_GEMGXLPLL, prci_phandle, PRCI_CLK_GEMGXLPLL);
qemu_fdt_setprop_string_array(fdt, nodename, "clock-names",
(char **)&ethclk_names, ARRAY_SIZE(ethclk_names));
qemu_fdt_setprop(fdt, nodename, "local-mac-address",
s->soc.gem.conf.macaddr.a, ETH_ALEN);
qemu_fdt_setprop_cell(fdt, nodename, "#address-cells", 1);
qemu_fdt_setprop_cell(fdt, nodename, "#size-cells", 0);
qemu_fdt_add_subnode(fdt, "/aliases");
qemu_fdt_setprop_string(fdt, "/aliases", "ethernet0", nodename);
g_free(nodename);
nodename = g_strdup_printf("/soc/ethernet@%lx/ethernet-phy@0",
(long)memmap[SIFIVE_U_DEV_GEM].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_cell(fdt, nodename, "phandle", phy_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "reg", 0x0);
g_free(nodename);
nodename = g_strdup_printf("/soc/serial@%lx",
(long)memmap[SIFIVE_U_DEV_UART1].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,uart0");
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_UART1].base,
0x0, memmap[SIFIVE_U_DEV_UART1].size);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_TLCLK);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_UART1_IRQ);
qemu_fdt_setprop_string(fdt, "/aliases", "serial1", nodename);
g_free(nodename);
nodename = g_strdup_printf("/soc/serial@%lx",
(long)memmap[SIFIVE_U_DEV_UART0].base);
qemu_fdt_add_subnode(fdt, nodename);
qemu_fdt_setprop_string(fdt, nodename, "compatible", "sifive,uart0");
qemu_fdt_setprop_cells(fdt, nodename, "reg",
0x0, memmap[SIFIVE_U_DEV_UART0].base,
0x0, memmap[SIFIVE_U_DEV_UART0].size);
qemu_fdt_setprop_cells(fdt, nodename, "clocks",
prci_phandle, PRCI_CLK_TLCLK);
qemu_fdt_setprop_cell(fdt, nodename, "interrupt-parent", plic_phandle);
qemu_fdt_setprop_cell(fdt, nodename, "interrupts", SIFIVE_U_UART0_IRQ);
qemu_fdt_add_subnode(fdt, "/chosen");
qemu_fdt_setprop_string(fdt, "/chosen", "stdout-path", nodename);
qemu_fdt_setprop_string(fdt, "/aliases", "serial0", nodename);
g_free(nodename);
update_bootargs:
if (cmdline) {
qemu_fdt_setprop_string(fdt, "/chosen", "bootargs", cmdline);
}
}
static void sifive_u_machine_reset(void *opaque, int n, int level)
{
/* gpio pin active low triggers reset */
if (!level) {
qemu_system_reset_request(SHUTDOWN_CAUSE_GUEST_RESET);
}
}
static void sifive_u_machine_init(MachineState *machine)
{
const MemMapEntry *memmap = sifive_u_memmap;
SiFiveUState *s = RISCV_U_MACHINE(machine);
MemoryRegion *system_memory = get_system_memory();
MemoryRegion *main_mem = g_new(MemoryRegion, 1);
MemoryRegion *flash0 = g_new(MemoryRegion, 1);
target_ulong start_addr = memmap[SIFIVE_U_DEV_DRAM].base;
target_ulong firmware_end_addr, kernel_start_addr;
uint32_t start_addr_hi32 = 0x00000000;
int i;
uint32_t fdt_load_addr;
uint64_t kernel_entry;
DriveInfo *dinfo;
DeviceState *flash_dev, *sd_dev;
qemu_irq flash_cs, sd_cs;
/* Initialize SoC */
object_initialize_child(OBJECT(machine), "soc", &s->soc, TYPE_RISCV_U_SOC);
object_property_set_uint(OBJECT(&s->soc), "serial", s->serial,
&error_abort);
object_property_set_str(OBJECT(&s->soc), "cpu-type", machine->cpu_type,
&error_abort);
qdev_realize(DEVICE(&s->soc), NULL, &error_abort);
/* register RAM */
memory_region_init_ram(main_mem, NULL, "riscv.sifive.u.ram",
machine->ram_size, &error_fatal);
memory_region_add_subregion(system_memory, memmap[SIFIVE_U_DEV_DRAM].base,
main_mem);
/* register QSPI0 Flash */
memory_region_init_ram(flash0, NULL, "riscv.sifive.u.flash0",
memmap[SIFIVE_U_DEV_FLASH0].size, &error_fatal);
memory_region_add_subregion(system_memory, memmap[SIFIVE_U_DEV_FLASH0].base,
flash0);
/* register gpio-restart */
qdev_connect_gpio_out(DEVICE(&(s->soc.gpio)), 10,
qemu_allocate_irq(sifive_u_machine_reset, NULL, 0));
/* create device tree */
create_fdt(s, memmap, machine->ram_size, machine->kernel_cmdline,
riscv_is_32bit(&s->soc.u_cpus));
if (s->start_in_flash) {
/*
* If start_in_flash property is given, assign s->msel to a value
* that representing booting from QSPI0 memory-mapped flash.
*
* This also means that when both start_in_flash and msel properties
* are given, start_in_flash takes the precedence over msel.
*
* Note this is to keep backward compatibility not to break existing
* users that use start_in_flash property.
*/
s->msel = MSEL_MEMMAP_QSPI0_FLASH;
}
switch (s->msel) {
case MSEL_MEMMAP_QSPI0_FLASH:
start_addr = memmap[SIFIVE_U_DEV_FLASH0].base;
break;
case MSEL_L2LIM_QSPI0_FLASH:
case MSEL_L2LIM_QSPI2_SD:
start_addr = memmap[SIFIVE_U_DEV_L2LIM].base;
break;
default:
start_addr = memmap[SIFIVE_U_DEV_DRAM].base;
break;
}
if (riscv_is_32bit(&s->soc.u_cpus)) {
firmware_end_addr = riscv_find_and_load_firmware(machine,
RISCV32_BIOS_BIN, start_addr, NULL);
} else {
firmware_end_addr = riscv_find_and_load_firmware(machine,
RISCV64_BIOS_BIN, start_addr, NULL);
}
if (machine->kernel_filename) {
kernel_start_addr = riscv_calc_kernel_start_addr(&s->soc.u_cpus,
firmware_end_addr);
kernel_entry = riscv_load_kernel(machine->kernel_filename,
kernel_start_addr, NULL);
if (machine->initrd_filename) {
hwaddr start;
hwaddr end = riscv_load_initrd(machine->initrd_filename,
machine->ram_size, kernel_entry,
&start);
qemu_fdt_setprop_cell(s->fdt, "/chosen",
"linux,initrd-start", start);
qemu_fdt_setprop_cell(s->fdt, "/chosen", "linux,initrd-end",
end);
}
} else {
/*
* If dynamic firmware is used, it doesn't know where is the next mode
* if kernel argument is not set.
*/
kernel_entry = 0;
}
/* Compute the fdt load address in dram */
fdt_load_addr = riscv_load_fdt(memmap[SIFIVE_U_DEV_DRAM].base,
machine->ram_size, s->fdt);
if (!riscv_is_32bit(&s->soc.u_cpus)) {
start_addr_hi32 = (uint64_t)start_addr >> 32;
}
/* reset vector */
uint32_t reset_vec[12] = {
s->msel, /* MSEL pin state */
0x00000297, /* 1: auipc t0, %pcrel_hi(fw_dyn) */
0x02c28613, /* addi a2, t0, %pcrel_lo(1b) */
0xf1402573, /* csrr a0, mhartid */
0,
0,
0x00028067, /* jr t0 */
start_addr, /* start: .dword */
start_addr_hi32,
fdt_load_addr, /* fdt_laddr: .dword */
0x00000000,
0x00000000,
/* fw_dyn: */
};
if (riscv_is_32bit(&s->soc.u_cpus)) {
reset_vec[4] = 0x0202a583; /* lw a1, 32(t0) */
reset_vec[5] = 0x0182a283; /* lw t0, 24(t0) */
} else {
reset_vec[4] = 0x0202b583; /* ld a1, 32(t0) */
reset_vec[5] = 0x0182b283; /* ld t0, 24(t0) */
}
/* copy in the reset vector in little_endian byte order */
for (i = 0; i < ARRAY_SIZE(reset_vec); i++) {
reset_vec[i] = cpu_to_le32(reset_vec[i]);
}
rom_add_blob_fixed_as("mrom.reset", reset_vec, sizeof(reset_vec),
memmap[SIFIVE_U_DEV_MROM].base, &address_space_memory);
riscv_rom_copy_firmware_info(machine, memmap[SIFIVE_U_DEV_MROM].base,
memmap[SIFIVE_U_DEV_MROM].size,
sizeof(reset_vec), kernel_entry);
/* Connect an SPI flash to SPI0 */
flash_dev = qdev_new("is25wp256");
dinfo = drive_get_next(IF_MTD);
if (dinfo) {
qdev_prop_set_drive_err(flash_dev, "drive",
blk_by_legacy_dinfo(dinfo),
&error_fatal);
}
qdev_realize_and_unref(flash_dev, BUS(s->soc.spi0.spi), &error_fatal);
flash_cs = qdev_get_gpio_in_named(flash_dev, SSI_GPIO_CS, 0);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->soc.spi0), 1, flash_cs);
/* Connect an SD card to SPI2 */
sd_dev = ssi_create_peripheral(s->soc.spi2.spi, "ssi-sd");
sd_cs = qdev_get_gpio_in_named(sd_dev, SSI_GPIO_CS, 0);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->soc.spi2), 1, sd_cs);
}
static bool sifive_u_machine_get_start_in_flash(Object *obj, Error **errp)
{
SiFiveUState *s = RISCV_U_MACHINE(obj);
return s->start_in_flash;
}
static void sifive_u_machine_set_start_in_flash(Object *obj, bool value, Error **errp)
{
SiFiveUState *s = RISCV_U_MACHINE(obj);
s->start_in_flash = value;
}
static void sifive_u_machine_get_uint32_prop(Object *obj, Visitor *v,
const char *name, void *opaque,
Error **errp)
{
visit_type_uint32(v, name, (uint32_t *)opaque, errp);
}
static void sifive_u_machine_set_uint32_prop(Object *obj, Visitor *v,
const char *name, void *opaque,
Error **errp)
{
visit_type_uint32(v, name, (uint32_t *)opaque, errp);
}
static void sifive_u_machine_instance_init(Object *obj)
{
SiFiveUState *s = RISCV_U_MACHINE(obj);
s->start_in_flash = false;
s->msel = 0;
object_property_add(obj, "msel", "uint32",
sifive_u_machine_get_uint32_prop,
sifive_u_machine_set_uint32_prop, NULL, &s->msel);
object_property_set_description(obj, "msel",
"Mode Select (MSEL[3:0]) pin state");
s->serial = OTP_SERIAL;
object_property_add(obj, "serial", "uint32",
sifive_u_machine_get_uint32_prop,
sifive_u_machine_set_uint32_prop, NULL, &s->serial);
object_property_set_description(obj, "serial", "Board serial number");
}
static void sifive_u_machine_class_init(ObjectClass *oc, void *data)
{
MachineClass *mc = MACHINE_CLASS(oc);
mc->desc = "RISC-V Board compatible with SiFive U SDK";
mc->init = sifive_u_machine_init;
mc->max_cpus = SIFIVE_U_MANAGEMENT_CPU_COUNT + SIFIVE_U_COMPUTE_CPU_COUNT;
mc->min_cpus = SIFIVE_U_MANAGEMENT_CPU_COUNT + 1;
mc->default_cpu_type = SIFIVE_U_CPU;
mc->default_cpus = mc->min_cpus;
object_class_property_add_bool(oc, "start-in-flash",
sifive_u_machine_get_start_in_flash,
sifive_u_machine_set_start_in_flash);
object_class_property_set_description(oc, "start-in-flash",
"Set on to tell QEMU's ROM to jump to "
"flash. Otherwise QEMU will jump to DRAM "
"or L2LIM depending on the msel value");
}
static const TypeInfo sifive_u_machine_typeinfo = {
.name = MACHINE_TYPE_NAME("sifive_u"),
.parent = TYPE_MACHINE,
.class_init = sifive_u_machine_class_init,
.instance_init = sifive_u_machine_instance_init,
.instance_size = sizeof(SiFiveUState),
};
static void sifive_u_machine_init_register_types(void)
{
type_register_static(&sifive_u_machine_typeinfo);
}
type_init(sifive_u_machine_init_register_types)
static void sifive_u_soc_instance_init(Object *obj)
{
SiFiveUSoCState *s = RISCV_U_SOC(obj);
object_initialize_child(obj, "e-cluster", &s->e_cluster, TYPE_CPU_CLUSTER);
qdev_prop_set_uint32(DEVICE(&s->e_cluster), "cluster-id", 0);
object_initialize_child(OBJECT(&s->e_cluster), "e-cpus", &s->e_cpus,
TYPE_RISCV_HART_ARRAY);
qdev_prop_set_uint32(DEVICE(&s->e_cpus), "num-harts", 1);
qdev_prop_set_uint32(DEVICE(&s->e_cpus), "hartid-base", 0);
qdev_prop_set_string(DEVICE(&s->e_cpus), "cpu-type", SIFIVE_E_CPU);
qdev_prop_set_uint64(DEVICE(&s->e_cpus), "resetvec", 0x1004);
object_initialize_child(obj, "u-cluster", &s->u_cluster, TYPE_CPU_CLUSTER);
qdev_prop_set_uint32(DEVICE(&s->u_cluster), "cluster-id", 1);
object_initialize_child(OBJECT(&s->u_cluster), "u-cpus", &s->u_cpus,
TYPE_RISCV_HART_ARRAY);
object_initialize_child(obj, "prci", &s->prci, TYPE_SIFIVE_U_PRCI);
object_initialize_child(obj, "otp", &s->otp, TYPE_SIFIVE_U_OTP);
object_initialize_child(obj, "gem", &s->gem, TYPE_CADENCE_GEM);
object_initialize_child(obj, "gpio", &s->gpio, TYPE_SIFIVE_GPIO);
object_initialize_child(obj, "pdma", &s->dma, TYPE_SIFIVE_PDMA);
object_initialize_child(obj, "spi0", &s->spi0, TYPE_SIFIVE_SPI);
object_initialize_child(obj, "spi2", &s->spi2, TYPE_SIFIVE_SPI);
}
static void sifive_u_soc_realize(DeviceState *dev, Error **errp)
{
MachineState *ms = MACHINE(qdev_get_machine());
SiFiveUSoCState *s = RISCV_U_SOC(dev);
const MemMapEntry *memmap = sifive_u_memmap;
MemoryRegion *system_memory = get_system_memory();
MemoryRegion *mask_rom = g_new(MemoryRegion, 1);
MemoryRegion *l2lim_mem = g_new(MemoryRegion, 1);
char *plic_hart_config;
size_t plic_hart_config_len;
int i;
NICInfo *nd = &nd_table[0];
qdev_prop_set_uint32(DEVICE(&s->u_cpus), "num-harts", ms->smp.cpus - 1);
qdev_prop_set_uint32(DEVICE(&s->u_cpus), "hartid-base", 1);
qdev_prop_set_string(DEVICE(&s->u_cpus), "cpu-type", s->cpu_type);
qdev_prop_set_uint64(DEVICE(&s->u_cpus), "resetvec", 0x1004);
sysbus_realize(SYS_BUS_DEVICE(&s->e_cpus), &error_abort);
sysbus_realize(SYS_BUS_DEVICE(&s->u_cpus), &error_abort);
/*
* The cluster must be realized after the RISC-V hart array container,
* as the container's CPU object is only created on realize, and the
* CPU must exist and have been parented into the cluster before the
* cluster is realized.
*/
qdev_realize(DEVICE(&s->e_cluster), NULL, &error_abort);
qdev_realize(DEVICE(&s->u_cluster), NULL, &error_abort);
/* boot rom */
memory_region_init_rom(mask_rom, OBJECT(dev), "riscv.sifive.u.mrom",
memmap[SIFIVE_U_DEV_MROM].size, &error_fatal);
memory_region_add_subregion(system_memory, memmap[SIFIVE_U_DEV_MROM].base,
mask_rom);
/*
* Add L2-LIM at reset size.
* This should be reduced in size as the L2 Cache Controller WayEnable
* register is incremented. Unfortunately I don't see a nice (or any) way
* to handle reducing or blocking out the L2 LIM while still allowing it
* be re returned to all enabled after a reset. For the time being, just
* leave it enabled all the time. This won't break anything, but will be
* too generous to misbehaving guests.
*/
memory_region_init_ram(l2lim_mem, NULL, "riscv.sifive.u.l2lim",
memmap[SIFIVE_U_DEV_L2LIM].size, &error_fatal);
memory_region_add_subregion(system_memory, memmap[SIFIVE_U_DEV_L2LIM].base,
l2lim_mem);
/* create PLIC hart topology configuration string */
plic_hart_config_len = (strlen(SIFIVE_U_PLIC_HART_CONFIG) + 1) *
ms->smp.cpus;
plic_hart_config = g_malloc0(plic_hart_config_len);
for (i = 0; i < ms->smp.cpus; i++) {
if (i != 0) {
strncat(plic_hart_config, "," SIFIVE_U_PLIC_HART_CONFIG,
plic_hart_config_len);
} else {
strncat(plic_hart_config, "M", plic_hart_config_len);
}
plic_hart_config_len -= (strlen(SIFIVE_U_PLIC_HART_CONFIG) + 1);
}
/* MMIO */
s->plic = sifive_plic_create(memmap[SIFIVE_U_DEV_PLIC].base,
plic_hart_config, 0,
SIFIVE_U_PLIC_NUM_SOURCES,
SIFIVE_U_PLIC_NUM_PRIORITIES,
SIFIVE_U_PLIC_PRIORITY_BASE,
SIFIVE_U_PLIC_PENDING_BASE,
SIFIVE_U_PLIC_ENABLE_BASE,
SIFIVE_U_PLIC_ENABLE_STRIDE,
SIFIVE_U_PLIC_CONTEXT_BASE,
SIFIVE_U_PLIC_CONTEXT_STRIDE,
memmap[SIFIVE_U_DEV_PLIC].size);
g_free(plic_hart_config);
sifive_uart_create(system_memory, memmap[SIFIVE_U_DEV_UART0].base,
serial_hd(0), qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_UART0_IRQ));
sifive_uart_create(system_memory, memmap[SIFIVE_U_DEV_UART1].base,
serial_hd(1), qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_UART1_IRQ));
sifive_clint_create(memmap[SIFIVE_U_DEV_CLINT].base,
memmap[SIFIVE_U_DEV_CLINT].size, 0, ms->smp.cpus,
SIFIVE_SIP_BASE, SIFIVE_TIMECMP_BASE, SIFIVE_TIME_BASE,
CLINT_TIMEBASE_FREQ, false);
if (!sysbus_realize(SYS_BUS_DEVICE(&s->prci), errp)) {
return;
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->prci), 0, memmap[SIFIVE_U_DEV_PRCI].base);
qdev_prop_set_uint32(DEVICE(&s->gpio), "ngpio", 16);
if (!sysbus_realize(SYS_BUS_DEVICE(&s->gpio), errp)) {
return;
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->gpio), 0, memmap[SIFIVE_U_DEV_GPIO].base);
/* Pass all GPIOs to the SOC layer so they are available to the board */
qdev_pass_gpios(DEVICE(&s->gpio), dev, NULL);
/* Connect GPIO interrupts to the PLIC */
for (i = 0; i < 16; i++) {
sysbus_connect_irq(SYS_BUS_DEVICE(&s->gpio), i,
qdev_get_gpio_in(DEVICE(s->plic),
SIFIVE_U_GPIO_IRQ0 + i));
}
/* PDMA */
sysbus_realize(SYS_BUS_DEVICE(&s->dma), errp);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->dma), 0, memmap[SIFIVE_U_DEV_PDMA].base);
/* Connect PDMA interrupts to the PLIC */
for (i = 0; i < SIFIVE_PDMA_IRQS; i++) {
sysbus_connect_irq(SYS_BUS_DEVICE(&s->dma), i,
qdev_get_gpio_in(DEVICE(s->plic),
SIFIVE_U_PDMA_IRQ0 + i));
}
qdev_prop_set_uint32(DEVICE(&s->otp), "serial", s->serial);
if (!sysbus_realize(SYS_BUS_DEVICE(&s->otp), errp)) {
return;
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->otp), 0, memmap[SIFIVE_U_DEV_OTP].base);
/* FIXME use qdev NIC properties instead of nd_table[] */
if (nd->used) {
qemu_check_nic_model(nd, TYPE_CADENCE_GEM);
qdev_set_nic_properties(DEVICE(&s->gem), nd);
}
object_property_set_int(OBJECT(&s->gem), "revision", GEM_REVISION,
&error_abort);
if (!sysbus_realize(SYS_BUS_DEVICE(&s->gem), errp)) {
return;
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->gem), 0, memmap[SIFIVE_U_DEV_GEM].base);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->gem), 0,
qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_GEM_IRQ));
create_unimplemented_device("riscv.sifive.u.gem-mgmt",
memmap[SIFIVE_U_DEV_GEM_MGMT].base, memmap[SIFIVE_U_DEV_GEM_MGMT].size);
create_unimplemented_device("riscv.sifive.u.dmc",
memmap[SIFIVE_U_DEV_DMC].base, memmap[SIFIVE_U_DEV_DMC].size);
create_unimplemented_device("riscv.sifive.u.l2cc",
memmap[SIFIVE_U_DEV_L2CC].base, memmap[SIFIVE_U_DEV_L2CC].size);
sysbus_realize(SYS_BUS_DEVICE(&s->spi0), errp);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi0), 0,
memmap[SIFIVE_U_DEV_QSPI0].base);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->spi0), 0,
qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_QSPI0_IRQ));
sysbus_realize(SYS_BUS_DEVICE(&s->spi2), errp);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi2), 0,
memmap[SIFIVE_U_DEV_QSPI2].base);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->spi2), 0,
qdev_get_gpio_in(DEVICE(s->plic), SIFIVE_U_QSPI2_IRQ));
}
static Property sifive_u_soc_props[] = {
DEFINE_PROP_UINT32("serial", SiFiveUSoCState, serial, OTP_SERIAL),
DEFINE_PROP_STRING("cpu-type", SiFiveUSoCState, cpu_type),
DEFINE_PROP_END_OF_LIST()
};
static void sifive_u_soc_class_init(ObjectClass *oc, void *data)
{
DeviceClass *dc = DEVICE_CLASS(oc);
device_class_set_props(dc, sifive_u_soc_props);
dc->realize = sifive_u_soc_realize;
/* Reason: Uses serial_hds in realize function, thus can't be used twice */
dc->user_creatable = false;
}
static const TypeInfo sifive_u_soc_type_info = {
.name = TYPE_RISCV_U_SOC,
.parent = TYPE_DEVICE,
.instance_size = sizeof(SiFiveUSoCState),
.instance_init = sifive_u_soc_instance_init,
.class_init = sifive_u_soc_class_init,
};
static void sifive_u_soc_register_types(void)
{
type_register_static(&sifive_u_soc_type_info);
}
type_init(sifive_u_soc_register_types)