When a failed PIO request caused the VM to stop, we still need to transfer the
PIO state even though DRQ=0 at this point.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When adding the werror=stop mode, some flags were added to s->status
which are used to determine what kind of operation should be restarted
when the VM is continued.
Unfortunately, it turns out that s->status is in fact a device register
and as such is visible to the guest (some of the abused bits are even
writable for the guest).
For migration we keep on using the old VMState field (renamed to
migration_compat_status) if the status register doesn't use any of the
previously abused bits. If it does, we use a subsection with a clean copy of
the status register.
The error status is always sent in a subsection if there is any error. It can't
use the old field because errors happen even without PCI.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. Unlike
DriveInfo, BlockDriverState should be about the host part only.
One of the remaining guest bits there is the "type hint". -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.
Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Fix regression of 667bb59: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After the re-org of the atapi code, it might not be intuitive for a
reader of the code to understand why we're inserting a 'media not
present' state between cd changes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some commands are supposed to report a Not Ready Condition (i.e. they require
a medium to be present in order to execute successfully). Instead of
duplicating the check in each command implementation, let's add a flag and
check it before calling the command.
This patch only converts existing checks, it does not introduce new checks for
any of the other commands that can/should report a Not Ready Condition.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The disk size can only change when the medium is changed, and the change
callback takes care of updating s->nb_sectors in this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for a table of function pointers, factor each command out from
ide_atapi_cmd() into its own function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 Table F.1 lists errors that can be thrown for the TEST_UNIT_READY
command. Going from medium not ready to medium ready states is
communicated by throwing an error.
This adds the missing 'tray opened' event that we fail to report to
guests. After doing this, older Linux guests properly revalidate a disc
on the change command. HSM violation errors, which caused Linux guests
to do a soft-reset of the link, also go away:
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
res 01/60:00:00:00:00/00:00:00:00:00/a0 Emask 0x3 (HSM violation)
ata2.00: status: { ERR }
ata2: soft resetting link
ata2.00: configured for MWDMA2
ata2: EH complete
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement the 'media' sub-command of the GET_EVENT_STATUS_NOTIFICATION
command. This helps us report tray open, tray closed, no media, media
present states to the guest.
Newer Linux kernels (2.6.38+) rely on this command to revalidate discs
after media change.
This patch also sends out tray open/closed status to the guest driver
when requested e.g. via the CDROM_DRIVE_STATUS ioctl (thanks Markus).
Without such notification, the guest and qemu's tray open/close status
was frequently out of sync, causing installers like Anaconda detecting
no disc instead of tray open, confusing them terribly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle GET_EVENT_STATUS_NOTIFICATION's No Event Available response in a
generic way so that future additions to the code to handle other
response types is easier.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of using magic numbers, use structs that are more descriptive of
the fields being used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes the code more readable.
Also, there's a block like:
if () {
...
} else {
...
}
Split that into
if () {
...
return;
}
...
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After a media change, the only commands allowed from the guest were
REQUEST_SENSE and INQUIRY. The guest may also issue
GET_EVENT_STATUS_NOTIFICATION commands to get media
changed notification.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Table 629 of the MMC-5 spec mentions two different error conditions when
a CDROM eject is requested: a) while a disc is inserted and b) while a
disc is not inserted.
Ensure we return the appropriate error for the present condition of the
drive and disc status.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drivers are free to lock drives without any media present. Such a
condition should not result in an error condition.
See Table 341 in MMC-5 spec for details.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
factor out ide initialization to call drive_get(IF_IDE)
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* 'for-anthony' of git://github.com/bonzini/qemu:
remove qemu_get_clock
add a generic scaling mechanism for timers
change all other clock references to use nanosecond resolution accessors
change all rt_clock references to use millisecond resolution accessors
add more helper functions with explicit milli/nanosecond resolution
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes two things:
1) CHECK POWER MODE
The error return value wasn't always zero, so it would show up as
offline. Error is now explicitly set to zero.
2) SMART
The smart values that were returned were invalid and tools like skdump
would not recognize that the smart data was actually valid and would
dump weird output. The data has been fixed up and raw value support
was added. Tools like skdump and palimpsest work as expected.
Signed-off-by: Brian Wheeler <bdwheele@indiana.edu>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Nothing prevented IRQ sharing on the ISA bus in principle. Not all
boards supported this, neither each and every card nor driver and OS.
Still, there existed valid IRQ sharing scenarios, (at least) two of them
can also be found in QEMU: >2 PC UARTs and the PREP IDE buses.
So remove this artificial restriction from our ISA model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Define and use dedicated constants for vm_stop reasons, they actually
have nothing to do with the EXCP_* defines used so far. At this chance,
specify more detailed reasons so that VM state change handlers can
evaluate them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Different AHCI controllers have a different number of ports, so the core
shouldn't care about the amount of ports available.
This patch makes the number of ports available to the AHCI core runtime
configurable, allowing us to have multiple different AHCI implementations
with different amounts of ports.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ahci code was missing its soft reset functionality. This wasn't really an
issue for Linux guests, but Windows gets confused when the controller doesn't
reset when it tells it so.
Using this patch I can now successfully boot Windows 7 from AHCI using AHCI
enabled SeaBIOS.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The drive sends a d2h init fis on initialization. Usually, the guest doesn't
receive fises yet at that point though, so the delivery is deferred.
Let's reflect that by sending the init fis on fis receive enablement.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sebastian's patch already did a pretty good job at splitting up ICH-9
AHCI code and the AHCI core. We need some more though. Copyright was missing,
the lspci dump belongs to ICH-9, we don't need the AHCI core to have its
own qdev device duplicate.
So let's split them a bit more in this patch, making things easier to
read an understand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Due to popular request, this patch adds a license header to ahci.h
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are multiple ahci devices out there. The currently implemented ich-9
is only one of the many. So let's split that one out into a separate file
to stress the difference.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before commit 622b520f, index=12 meant bus=1,unit=5.
Since the commit, it means bus=0,unit=12. The drive is created, but
not the guest device. That's because the controllers we use with
if=scsi drives (lsi53c895a and esp) support only 7 units, and
scsi_bus_legacy_handle_cmdline() ignores drives with unit numbers
exceeding that limit.
Changing the mapping of index to bus, unit is a regression. Breaking
-drive invocations that used to work just makes it worse.
Revert the part of commit 622b520f that causes this, and clean up
some.
Note that the fix only affects if=scsi. You can still put more than 7
units on a SCSI bus with -device & friends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The len and is_write arguments to cpu_physical_memory_unmap() were
swapped. This patch changes calls to use the correct argument ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extend the change_cb callback with a reason argument, and use it
to tell drivers about size changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With bm == NULL, other code in the same function would crash.
This bug was reported by cppcheck:
hw/ide/pci.c:280: error: Possible null pointer dereference: bm
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Merge ide_dma_submit_check into it's only caller. Also use tail recursion
using a goto instead of a real recursion - this avoid overflowing the
stack in the pathological situation of an recurring error that is ignored.
We'll still be busy looping in ide_dma_cb, but at least won't eat up
all stack space after this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currenly the code only resets the io_buffer_index field for reads,
but the code seems to expect this for all types of I/O. I guess
we simply don't hit large enough transfers that would require this
often enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Factor the DMA I/O path that is duplicated between read and write
commands, into common helpers using the s->is_read flag added for
the macio ATA controller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>