During a sector erase (but not a chip erase), the embeded erase program
can be suspended. Once suspended, the sectors not selected for erasure
may be read and programmed. Autoselect mode is allowed during erase
suspend mode. Presumably, CFI queries are similarly allowed so this
commit allows them as well.
Since guest firmware can use status bits DQ7, DQ6, DQ3, and DQ2 to
determine the current state of sector erasure, these bits are properly
implemented.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-10-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After two unlock cycles and a sector erase command, the AMD flash chips
start a 50 us erase time out. Any additional sector erase commands add a
sector to be erased and restart the 50 us timeout. During the timeout,
status bit DQ3 is cleared. After the time out, DQ3 is asserted during
erasure.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-9-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When the flash device is performing a chip erase, all commands are
ignored. When it is performing a sector erase, only the erase suspend
command is valid, which is currently not supported.
In particular, the reset command should not cause the device to reset to
read array mode while programming is on going.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-8-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After a flash device enters CFI mode from autoselect mode, the reset
command returns the device to autoselect mode. An additional reset
command is necessary to return to read array mode.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-7-stephen.checkoway@oberlin.edu>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Split the if() condition check and arrange the indentation to
ease the review of the next patches. No logical change.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-21-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Extract the pflash_regions_count() function, the code will be
easier to review.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-20-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased, add assert() on pri_offset]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The 'page mode' feature entry was implicitly set as zero
(not supported). Document it exists, so we won't discard
it if we squeeze the CFI table.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Manufacturers are allowed to move the PRI table, this is why the
offset is queryable via fixed offsets 0x15/0x16.
Add a variable to hold the offset, so it will be easier to later
move the PRI table.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-17-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We can directly use pfl->total_len, remove the local 'chip_len'
variable.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Most AMD commands only examine 11 bits of the address. This masks the
addresses used in the comparison to 11 bits. The exceptions are word or
sector addresses which use offset directly rather than the shifted
offset, boff.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-4-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The pflash_read()/pflash_write() can check the device endianess
via the pfl->be variable, so remove the 'int be' argument.
Since the big/little MemoryRegionOps are now identical, it is
pointless to declare them both. Unify them.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch to ease review]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Extract the code block in a new function, remove a goto statement.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, remove the XXX tracing comment]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The load/store API eases code review.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, simplified tracing]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The load/store API eases code review.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Pull out all of the code to modify the status into simple helper
functions. Status handling becomes more complex once multiple
chips are interleaved to produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Always compile the debug code to prevent format string to bitrot.
Delete dead code.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch, use PRIx32]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Use a field width format to have a single function to log
the different width accesses.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-4-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Call the read() trace function after the value is set, so we can
log the returned value.
Rename the I/O trace functions with '_io_' in their name.
Reviewed-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make kvmppc_xive_disconnect() able to undo the changes of a partial
execution of kvmppc_xive_connect() and use it to perform rollback.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <156198735673.293938.7313195993600841641.stgit@bahia>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reseted, the hypervisor (Linux or OPAL) invalidates the
POOL interrupt context of a CPU with this special command. It returns
the POOL CAM line value and resets the VP bit.
Fixes: 4836b45510 ("ppc/xive: activate HV support")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the software modifies the XIVE internal structures, ESB, EAS,
END, NVT, it also must update the caches of the different XIVE
sub-engines. HW offers a set of common interface for such purpose.
The CWATCH_SPEC register defines the block/index of the target and a
set of flags to perform a full update and to watch for update
conflicts.
The cache watch CWATCH_DATAX registers are then loaded with the target
data with a first read on CWATCH_DATA0. Writing back is done in the
opposit order, CWATCH_DATA0 triggering the update.
The SCRUB_TRIG registers are used to flush the cache in RAM, and to
possibly invalidate it. Cache disablement is also an option but as we
do not model the cache, these registers are no-ops
Today, the modeling of these registers is incorrect but it did not
impact the set up of a baremetal system. However, running KVM requires
a rework.
Fixes: 2dfa91a2aa ("ppc/pnv: add a XIVE interrupt controller model for POWER9")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the hypervisor (KVM) dispatches a vCPU on a HW thread, it restores
its thread interrupt context. The Pending Interrupt Priority Register
(PIPR) is computed from the Interrupt Pending Buffer (IPB) and stores
should not be allowed to change its value.
Fixes: 207d9fe985 ("ppc/xive: introduce the XIVE interrupt thread context")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When an interrupt needs to be delivered, the XIVE interrupt controller
presenter scans the CAM lines of the thread interrupt contexts of the
HW threads of the chip to find a matching vCPU. The interrupt context
is composed of 4 different sets of registers: Physical, HV, OS and
User.
The encoding of the Physical CAM line depends on the mode in which the
interrupt controller is operating: CAM mode or block group mode.
Block group mode being the default configuration today on POWER9 and
the only one available on the next POWER10 generation, enforce this
encoding in the Physical CAM line :
chip << 19 | 0000000 0 0001 thread (7Bit)
It fits the overall encoding of the NVT ids and simplifies the matching
algorithm in the presenter.
Fixes: d514c48d41 ("ppc/xive: hardwire the Physical CAM line of the thread context")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The init_emu() handles are now empty. Remove them and rename
spapr_irq_init_device() to spapr_irq_init_kvm().
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190614165920.12670-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt device is fully initialized at reset when the CAS
negotiation process has completed. Depending on the KVM capabilities,
the SpaprXive memory regions (ESB, TIMA) are initialized with a host
MMIO backend or a QEMU emulated backend. This results in a complex
initialization sequence partially done at realize and later at reset,
and some memory region leaks.
To simplify this sequence and to remove of the late initialization of
the emulated device which is required to be done only once, we
introduce new memory regions specific for KVM. These regions are
mapped as overlaps on top of the emulated device to make use of the
host MMIOs. Also provide proper cleanups of these regions when the
XIVE KVM device is destroyed to fix the leaks.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190614165920.12670-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hot-unplugging a PHB with a VFIO device connected to it crashes QEMU:
-device spapr-pci-host-bridge,index=1,id=phb1 \
-device vfio-pci,host=0034:01:00.3,id=vfio0
(qemu) device_del phb1
[ 357.207183] iommu: Removing device 0001:00:00.0 from group 1
[ 360.375523] rpadlpar_io: slot PHB 1 removed
qemu-system-ppc64: memory.c:2742:
do_address_space_destroy: Assertion `QTAILQ_EMPTY(&as->listeners)' failed.
'as' is the IOMMU address space, which indeed has a listener registered
to by vfio_connect_container() when the VFIO device is realized. This
listener is supposed to be unregistered by vfio_disconnect_container()
when the VFIO device is finalized. Unfortunately, the VFIO device hasn't
reached finalize yet at the time the PHB unrealize function is called,
and address_space_destroy() gets called with the VFIO listener still
being registered.
All regions have just been unmapped from the address space. Listeners
aren't needed anymore at this point. Remove them before destroying the
address space.
The VFIO code will try to remove them _again_ at device finalize,
but it is okay since memory_listener_unregister() is idempotent.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156110925375.92514.11649846071216864570.stgit@bahia.lan>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Correct spelling error pointed out by aik]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a KVM helper and its stub instead of guarding the code with
CONFIG_KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051055736.224162.11641594431517798715.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make xics_kvm_disconnect() able to undo the changes of a partial execution
of xics_kvm_connect() and use it to perform rollback.
Note that kvmppc_define_rtas_kernel_token(0) never fails, no matter the
RTAS call has been defined or not.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077922319.433243.609897156640506891.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows errors happening there to be propagated up to spapr_irq,
just like XIVE already does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077921763.433243.4614327010172954196.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Passing both errp and &local_err to functions is a recipe for messing
things up.
Since we must use &local_err for icp_kvm_realize(), use &local_err
everywhere where rollback must happen and have a single call to
error_propagate() them all. While here, add errno to the error
message.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077921212.433243.11716701611944816815.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no need to rollback anything at this point, so just return an
error.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077920657.433243.13541093940589972734.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch to using the connect/disconnect terminology like we already do for
XIVE.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077920102.433243.6605099291134598170.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvmppc_set_interrupt() has a stub that does nothing when CONFIG_KVM is
not defined.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051055182.224162.15842560287892241124.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_enabled() expands to (0) when CONFIG_KVM is not defined. It is
likely that the compiler will optimize the code out. And even if
it doesn't, we have a stub for kvmppc_get_hypercall().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051054630.224162.6140707722034383410.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_enabled() expands to (0) when CONFIG_KVM is not defined. The first
CONFIG_KVM guard is thus useless and it is likely that the compiler
will optimize the code out in the case of the second guard. And even
if it doesn't, we have a stub for kvmppc_get_hypercall().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051054077.224162.9332715375637801197.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_enabled() expands to (0) when CONFIG_KVM is not defined. It is
likely that the compiler will optimize the code out. And even if
it doesn't, we have a stub for kvmppc_get_hypercall().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051053529.224162.3489943067148134636.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_enabled() expands to (0) when CONFIG_KVM is not defined.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156051052977.224162.17306829691809502082.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Checking that we're not using the in-kernel XICS is ok with the "xics"
interrupt controller mode, but it is definitely not enough with the
other modes since the guest could be using XIVE.
Ensure XIVE is not in use when emulated XICS RTAS/hypercalls are
called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077253666.424706.6104557911104491047.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_dt_drc() scans the aliases of all DRConnector objects and filters
the ones that it will use to generate OF properties according to their
owner and type.
Passing bus->parent_dev _works_ if bus belongs to a PCI bridge, but it is
NULL if it is the PHB's root bus. This causes all allocated PCI DRCs to
be associated to all PHBs (visible in their "ibm,drc-types" properties).
As a consequence, hot unplugging a PHB results in PCI devices from the
other PHBs to be unplugged as well, and likely confuses the guest.
Use the same logic as in add_drcs() to ensure the correct owner is passed
to spapr_dt_drc().
Fixes: 14e714900f "spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges"
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156084737348.512412.3552825999605902691.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that no one is tempted to drop that code, which is never called
for cold plugged CPUs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156078063349.435533.12283208810037409702.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Older KVMs on POWER9 don't support destroying/recreating a KVM XICS
device, which is required by 'dual' interrupt controller mode. This
causes QEMU to emit a warning when the guest is rebooted and to fall
back on XICS emulation:
qemu-system-ppc64: warning: kernel_irqchip allowed but unavailable:
Error on KVM_CREATE_DEVICE for XICS: File exists
If kernel irqchip is required, QEMU will thus exit when the guest is
first rebooted. Failing QEMU this late may be a painful experience
for the user.
Detect that and exit at machine init instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044430517.125694.6207865998817342638.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU may crash when running a spapr machine in 'dual' interrupt controller
mode on some older (but not that old, eg. ubuntu 18.04.2) KVMs with partial
XIVE support:
qemu-system-ppc64: hw/ppc/spapr_rtas.c:411: spapr_rtas_register:
Assertion `!name || !rtas_table[token].name' failed.
XICS is controlled by the guest thanks to a set of RTAS calls. Depending
on whether KVM XICS is used or not, the RTAS calls are handled by KVM or
QEMU. In both cases, QEMU needs to expose the RTAS calls to the guest
through the "rtas" node of the device tree.
The spapr_rtas_register() helper takes care of all of that: it adds the
RTAS call token to the "rtas" node and registers a QEMU callback to be
invoked when the guest issues the RTAS call. In the KVM XICS case, QEMU
registers a dummy callback that just prints an error since it isn't
supposed to be invoked, ever.
Historically, the XICS controller was setup during machine init and
released during final teardown. This changed when the 'dual' interrupt
controller mode was added to the spapr machine: in this case we need
to tear the XICS down and set it up again during machine reset. The
crash happens because we indeed have an incompatibility with older
KVMs that forces QEMU to fallback on emulated XICS, which tries to
re-registers the same RTAS calls.
This could be fixed by adding proper rollback that would unregister
RTAS calls on error. But since the emulated RTAS calls in QEMU can
now detect when they are mistakenly called while KVM XICS is in
use, it seems simpler to register them once and for all at machine
init. This fixes the crash and allows to remove some now useless
lines of code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429963.125694.13710679451927268758.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICS-related RTAS calls and hypercalls in QEMU are not supposed to
be called when the KVM in-kernel XICS is in use.
Add some explicit checks to detect that, print an error message and report
an hardware error to the guest.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429419.125694.507569071972451514.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
[dwg: Correction to commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 14e714900f refactored the call to spapr_dt_drc(),
introducing a potential NULL pointer dereference while
accessing bus->parent_dev.
A trivial audit show 'bus' is not null in the two places
the static function spapr_dt_drc() is called.
Since the 'bus' parameter is not NULL in both callers, remove
remove the test on if (bus), and add an assert() to silent
static analyzers.
This fixes:
/hw/ppc/spapr_pci.c: 1367 in spapr_dt_pci_bus()
>>> CID 1401933: Null pointer dereferences (FORWARD_NULL)
>>> Dereferencing null pointer "bus".
1367 ret = spapr_dt_drc(fdt, offset, OBJECT(bus->parent_dev),
1368 SPAPR_DR_CONNECTOR_TYPE_PCI);
Fixes: 14e714900f
Reported-by: Coverity (CID 1401933)
Suggested-by: Greg Kurz <groug@kaod.org>
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190613213406.22053-1-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It has now became useless with the previous patch.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612174345.9799-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PNV_XSCOM_BASE and PNV_XSCOM_SIZE macros are specific to POWER8
and they are used when the device tree is populated and the MMIO
region created, even for POWER9 chips. This is not too much of a
problem today because we don't have important devices on the second
chip, but we might have oneday (PHBs).
Fix by using the appropriate macros in case of P9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612174345.9799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The firmware (skiboot) of the PowerNV machines can configure the XIVE
interrupt controller to activate StoreEOI on the ESB pages of the
interrupts. This feature lets software do an EOI with a store instead
of a load. It is not activated today on P9 for rare race condition
issues but it should be on future processors.
Nevertheless, QEMU has a model for StoreEOI which can be used today by
experimental firmwares. But, the use of object_property_set_int() in
the PnvXive model is incorrect and crashes QEMU. Replace it with a
direct access to the ESB flags of the XiveSource object modeling the
internal sources of the interrupt controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612162357.29566-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Following the previous patch, this patch adds peripheral devices to the
newly introduced SBSA-ref machine.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1561890034-15921-3-git-send-email-hongbo.zhang@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For AArch64, the existing "virt" machine is primarily meant to
run on KVM and execute virtualization workloads, but we need an
environment as faithful as possible to physical hardware, for supporting
firmware and OS development for physical Aarch64 machines.
This patch introduces new machine type 'sbsa-ref' with main features:
- Based on 'virt' machine type.
- A new memory map.
- CPU type cortex-a57.
- EL2 and EL3 are enabled.
- GIC version 3.
- System bus AHCI controller.
- System bus EHCI controller.
- CDROM and hard disc on AHCI bus.
- E1000E ethernet card on PCIE bus.
- VGA display adaptor on PCIE bus.
- No virtio devices.
- No fw_cfg device.
- No ACPI table supplied.
- Only minimal device tree nodes.
Arm Trusted Firmware and UEFI porting to this are done accordingly,
and the firmware should supply ACPI tables to the guest OS. The
minimal device tree nodes supplied by QEMU for this platform are only
to pass the dynamic info reflecting command line input to firmware,
not for loading the guest OS.
To make the review easier, this task is split into two patches, the
fundamental skeleton part and the peripheral devices part; this patch is
the first part.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1561890034-15921-2-git-send-email-hongbo.zhang@linaro.org
[PMM: commit message tweaks; moved some bits between patch 1 and 2
to ensure patch 1 builds cleanly; removed unneeded lines from
Kconfig stanza; only provide board for qemu-system-aarch64, not
qemu-system-arm; added MAINTAINERS entry]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ast2500 uses the watchdog to reset the SDRAM controller. This
operation is usually performed by u-boot's memory training procedure,
and it is enabled by setting a bit in the SCU and then causing the
watchdog to expire. Therefore, we need the watchdog to be able to
access the SCU's register space.
This causes the watchdog to not perform a system reset when the bit is
set. In the future it could perform a reset of the SDMC model.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190621065242.32535-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The legacy interface only supported up to 32 IRQs, which became
restrictive around the AST2400 generation. QEMU support for the SoCs
started with the AST2400 along with an effort to reimplement and
upstream drivers for Linux, so up until this point the consumers of the
QEMU ASPEED support only required the 64 IRQ register interface.
In an effort to support older BMC firmware, add support for the 32 IRQ
interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-22-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XDMA engine embedded in the Aspeed SOCs performs PCI DMA operations
between the SOC (acting as a BMC) and a host processor in a server.
The XDMA engine exists on the AST2400, AST2500, and AST2600 SOCs, so
enable it for all of those. Add trace events on the important register
writes in the XDMA engine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-21-clg@kaod.org
[clg: - changed title ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Swift board is an OpenPOWER system hosting POWER processors.
Add support for their BMC including the I2C devices as found on HW.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-20-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DRAM address of a DMA transaction depends on the DRAM base address
of the SoC. Inform the SMC controller model with this value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618165311.27066-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RAM memory region is defined after the SoC is realized when the
SDMC controller has checked that the defined RAM size for the machine
is correct. This is problematic for controller models requiring a link
on the RAM region, for DMA support in the SMC controller for instance.
Introduce a container memory region for the RAM that we can link into
the controllers early, before the SoC is realized. It will be
populated with the RAM region after the checks have be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It has never been used as far as I can tell from the git history.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the host decrements the counter register that results in a negative
delta. This is then passed to muldiv64 which only handles unsigned
numbers resulting in bogus results.
This fix ensures the delta being operated on is positive.
Test case: kexec a kernel using aspeed_timer and it will freeze on the
second bootup when the kernel initializes the timer. With this patch
that no longer happens and the timer appears to run OK.
Signed-off-by: Christian Svensson <bluecmd@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20190618165311.27066-12-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the match value exceeds reload then we don't want to include it in
calculations for the next event.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the datasheet:
This register stores the current status of counter #N. When timer
enable bit TMC30[N * b] is disabled, the reload register will be
loaded into this counter. When timer bit TMC30[N * b] is set, the
counter will start to decrement. CPU can update this register value
when enable bit is set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux kernel driver was updated in commit 4451d3f59f2a
("clocksource/drivers/fttmr010: Fix set_next_event handler) to fix an
issue observed on hardware:
> RELOAD register is loaded into COUNT register when the aspeed timer
> is enabled, which means the next event may be delayed because timer
> interrupt won't be generated until <0xFFFFFFFF - current_count +
> cycles>.
When running under Qemu, the system appeared "laggy". The guest is now
scheduling timer events too regularly, starving the host of CPU time.
This patch modifies the timer model to attempt to schedule the timer
expiry as the guest requests, but if we have missed the deadline we
re interrupt and try again, which allows the guest to catch up.
Provides expected behaviour with old and new guest code.
Fixes: c04bd47db6 ("hw/timer: Add ASPEED timer device model")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-8-clg@kaod.org
[clg: - merged a fix from Andrew Jeffery <andrew@aj.id.au>
"Fire interrupt on failure to meet deadline"
https://lists.ozlabs.org/pipermail/openbmc/2019-January/014641.html
- adapted commit log
- checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoCs have two MACs. Extend the Aspeed model to support a
second NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current models of the Aspeed SoCs only have one CPU but future
ones will support SMP. Introduce a new num_cpus field at the SoC class
level to define the number of available CPUs per SoC and also
introduce a 'num-cpus' property to activate the CPUs configured for
the machine.
The max_cpus limit of the machine should depend on the SoC definition
but, unfortunately, these values are not available when the machine
class is initialized. This is the reason why we add a check on
num_cpus in the AspeedSoC realize handler.
SMP support will be activated when models for such SoCs are implemented.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All systems have an RTC.
The IRQ is hooked up but the model does not use it at this stage. There
is no guest code that uses it, so this limitation is acceptable.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RTC is modeled to provide time and date functionality. It is
initialised at zero to match the hardware.
There is no modelling of the alarm functionality, which includes the IRQ
line. As there is no guest code to exercise this function that is
acceptable for now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a slightly different address space and have a different set
of controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a different CPU and a different IRQ number layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Datasheet for i.MX7 is incorrect and i.MX7's PCI IRQ mapping matches
that of i.MX6:
* INTD/MSI 122
* INTC 123
* INTB 124
* INTA 125
Fix all of the relevant code to reflect that fact. Needed by latest
Linux kernels.
(Reference: Linux kernel commit 538d6e9d597584e80 from an
NXP employee confirming that the datasheet is incorrect and
with a report of a test against hardware.)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added ref to kernel commit confirming the datasheet error]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MSI mapping needs to be update when MSI address changes, so add the
code to do so.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Expression to calculate update_msi_mapping in code handling writes to
DESIGNWARE_PCIE_MSI_INTR0_ENABLE is missing an ! operator and should
be:
!!root->msi.intr[0].enable ^ !!val;
so that MSI mapping is updated when enabled transitions from either
"none" -> "any" or "any" -> "none". Since that register shouldn't be
written to very often, change the code to update MSI mapping
unconditionally instead of trying to fix the update_msi_mapping logic.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add no-op/unimplemented PCIE PHY IP block. Needed by new kernels to
use PCIE.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow cortex-a7 to be used with the virt board; it supports
the v7VE features and there is no reason to deny this type.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: fc5404f7-4d1d-c28f-6e48-d8799c82acc0@web.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This machine correctly defines its default_cpu_type to cortex-m3
and report an error if the user requested another cpu_type,
however it does not exit, and this can confuse users trying
to use another core:
$ qemu-system-arm -M emcraft-sf2 -cpu cortex-m4 -kernel test-m4.elf
qemu-system-arm: This board can only be used with CPU cortex-m3-arm-cpu
[output related to M3 core ...]
The CPU is indeed a M3 core:
(qemu) info qom-tree
/machine (emcraft-sf2-machine)
/unattached (container)
/device[0] (msf2-soc)
/armv7m (armv7m)
/cpu (cortex-m3-arm-cpu)
Add the missing exit() call to return to the shell.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20190617160136.29930-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the condition used to check whether the initrd fits
into RAM; in some cases if an initrd was also passed on
the command line we would get an error stating that it
was too big to fit into RAM after the kernel. Despite the
error the loader continued anyway, though, so also add an
exit(1) when the initrd is actually too big.
Fixes: 852dc64d66 ("hw/arm/boot: Diagnose layouts that put initrd or
DTB off the end of RAM")
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618125844.4863-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename function arguments to make intent clearer.
Better documentation for slot control logic.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
During boot, linux guests tend to clear all bits in pcie slot status
register which is used for hotplug.
If they clear bits that weren't set this is racy and will lose events:
not a big problem for manual hotplug on bare-metal, but a problem for us.
For example, the following is broken ATM:
/x86_64-softmmu/qemu-system-x86_64 -enable-kvm -S -machine q35 \
-device pcie-root-port,id=pcie_root_port_0,slot=2,chassis=2,addr=0x2,bus=pcie.0 \
-device virtio-balloon-pci,id=balloon,bus=pcie_root_port_0 \
-monitor stdio disk.qcow2
(qemu)device_del balloon
(qemu)cont
Balloon isn't deleted as it should.
As a work-around, detect this attempt to clear slot status and revert
status to what it was before the write.
Note: in theory this can be detected as a duplicate button press
which cancels the previous press. Does not seem to happen in
practice as guests seem to only have this bug during init.
Note2: the right thing to do is probably to fix Linux to
read status before clearing it, and act on the bits that are set.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
During boot, linux would sometimes overwrites control of a powered off
slot before powering it on. Unfortunately QEMU interprets that as a
power off request and ejects the device.
For example:
/x86_64-softmmu/qemu-system-x86_64 -enable-kvm -S -machine q35 \
-device pcie-root-port,id=pcie_root_port_0,slot=2,chassis=2,addr=0x2,bus=pcie.0 \
-monitor stdio disk.qcow2
(qemu)device_add virtio-balloon-pci,id=balloon,bus=pcie_root_port_0
(qemu)cont
Balloon is deleted during guest boot.
To fix, save control beforehand and check that power
or led state actually change before ejecting.
Note: this is more a hack than a solution, ideally we'd
find a better way to detect ejects, or move away
from ejects completely and instead monitor whether
it's safe to delete device due to e.g. its power state.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
If we are trying to set multiple bits at once, testing that just one of
them is already set gives a false positive. As a result we won't
interrupt guest if e.g. presence detection change and attention button
press are both set. This happens with multi-function device removal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
-----BEGIN PGP SIGNATURE-----
iQFOBAABCgA4FiEE+AwAYwjiLP2KkueYDPVXL9f7Va8FAl0Q7JgaHGFudGhvbnku
cGVyYXJkQGNpdHJpeC5jb20ACgkQDPVXL9f7Va8B1wf/bL9gdT/1R9474ZfbWAGZ
KzkCo0C3jXUWRXd9z/UVwkmOhz0tLj1otx0fR+HFM4An+YAY6D0oZAKO9SCHhGDQ
XflAK74dw1ieuZI+3Q5PXQO5xM1Oz0J+3TGlOFdZlh5UD68mEzteGnzU/zzs7i4E
AZiKVOdO4YzMdHLVO4X/AqZH48n82FxjKcog7cZ9fTqDUz8SZGwJVSWocUZ0yOWb
uhAacvhwHeZj64NuNShyF/RM7jolTk4CZWJv8Gy9CPxOM7noQIv0ttwu+QWCmODg
pdTxd8HrE4rTnKaQFiHVas/AZ3cOfRw9RjdsARhXtGJq8AaQag9Q0iLZpyBYBfsF
6w==
=MDEA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/aperard/tags/pull-xen-20190624' into staging
Xen queue
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
# gpg: Signature made Mon 24 Jun 2019 16:30:32 BST
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20190624:
xen: Import other xen/io/*.h
Revert xen/io/ring.h of "Clean up a few header guard symbols"
xen: Drop includes of xen/hvm/params.h
xen: Avoid VLA
xen-bus / xen-block: add support for event channel polling
xen-bus: allow AioContext to be specified for each event channel
xen-bus: use a separate fd for each event channel
xen-block: support feature-large-sector-size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix bit masks of registers for offset and pitch and also handle
default values for both R128P and RV100. This improves picture a bit
but does not resolve all problems yet so there might be some more bugs
somewhere.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20190624100005.7A1CA746395@zero.eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This adds DDC support to ati-vga and connects i2c-ddc to it. This
allows at least MacOS with an ATI ndrv, Linux radeonfb and MorphOS to
get monitor EDID info (although MorphOS splash screen is not displayed
and radeonfb needs additional tables from vgabios-rv100). Xorg needs
additional support from VESA vgabios, it's missing INT10 0x4F15
function (see
https://gitlab.freedesktop.org/xorg/xserver/blob/master/hw/xfree86/vbe/vbe.c)
without which no DDC is available that also prevents loading the
accelerated X driver.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 046ddebb7ec8db48c4e877ee444ec1c41e385a74.1561028123.git.balaton@eik.bme.hu
ati-vga: Clarify comment
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20190620195213.C54127461AE@zero.eik.bme.hu
ati-vga: Add DDC reg names for debug
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20190621181459.2F8207462AA@zero.eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bitbang i2c implementation is also useful for other device models
such as DDC in display controllers. Move the header to include/hw/i2c/
to allow it to be used from other device models and adjust users of
this include. This also reverts commit 2b4c1125ac which is no longer
needed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 5d1fe4db846ab9be4b77ddb0d43cc74cd200a003.1561028123.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extend the RISC-V kernel loader to support Image and uImage files.
A Linux kernel can now be booted with:
qemu-system-riscv64 -machine virt -bios fw_jump.bin -kernel Image
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add support for loading a firmware file for the virt machine and the
SiFive U. This can be run with the following command:
qemu-system-riscv64 -machine virt -bios fw_jump.bin -kernel vmlinux
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Split the common RISC-V boot functions into a seperate file. This allows
us to share the common code.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the PLIC is instantiated to support only one hart, while
the machine allows at most 4 harts to be created. When more than 1
hart is configured, PLIC needs to instantiated to support multicore,
otherwise an SMP OS does not work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the cpu, plic and ethclk nodes' phandles are hard-coded
to 1/2/3 in DT. If we configure more than 1 cpu for the machine,
all cpu nodes' phandles conflict with each other as they are all 1.
Fix it by removing the hardcode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Fix some simple checkpatch.pl warnings in rc4030.c.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1561472838-32272-3-git-send-email-aleksandar.markovic@rt-rk.com>
The size is one byte less than it should be:
address-space: rc4030-dma
0000000000000000-00000000fffffffe (prio 0, i/o): rc4030.dma
rc4030 is used in MIPS Jazz board context.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1561472838-32272-2-git-send-email-aleksandar.markovic@rt-rk.com>
One byte is missing, use an aligned size.
(qemu) info mtree
memory-region: pci0-mem
0000000000000000-00000000fffffffe (prio 0, i/o): pci0-mem
^
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-8-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-7-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-6-f4bug@amsat.org>
Since we'll move this code around, fix its style first:
ERROR: space prohibited between function name and open parenthesis
ERROR: line over 90 characters
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-5-f4bug@amsat.org>
Since we'll move this code around, fix its style first:
ERROR: braces {} are necessary for all arms of this statement
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-4-f4bug@amsat.org>
Since we'll move this code around, fix its style first:
ERROR: code indent should never use tabs
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-3-f4bug@amsat.org>
Since commit 8c06fbdf36 checkpatch.pl enforce a new multiline
comment syntax. Since we'll move this code around, fix its style
first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190624222844.26584-2-f4bug@amsat.org>
Currently, there is no cpu topology defined in RISC-V.
Define a device tree node that clearly describes the
entire topology. This saves the trouble of scanning individual
cache to figure out the topology.
Here is the linux kernel patch series that enables topology
for RISC-V.
http://lists.infradead.org/pipermail/linux-riscv/2019-June/005072.html
CPU topology after applying this patch in QEMU & above series in kernel
/ # cat /sys/devices/system/cpu/cpu2/topology/thread_siblings_list
2
/ # cat /sys/devices/system/cpu/cpu2/topology/physical_package_id
0
/ # cat /sys/devices/system/cpu/cpu2/topology/core_siblings_list
0-7
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
A vfio-ccw device may provide an async command subregion for
issuing halt/clear subchannel requests. If it is present, use
it for sending halt/clear request to the device; if not, fall
back to emulation (as done today).
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <20190613092542.2834-1-cohuck@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Use the new helper.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20190617101036.4087-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The device mistakenly reports that the Weighted Round Robin with Urgent
Priority Class arbitration mechanism is supported.
It is not.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Message-id: 20190606092530.14206-1-klaus@birkelund.eu
Acked-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
A Xen public header have been imported into QEMU (by
f65eadb639 "xen: import ring.h from xen"), but there are other header
that depends on ring.h which come from the system when building QEMU.
This patch resolves the issue of having headers from the system
importing a different copie of ring.h.
This patch is prompt by the build issue described in the previous
patch: 'Revert xen/io/ring.h of "Clean up a few header guard symbols"'
ring.h and the new imported headers are moved to
"include/hw/xen/interface" as those describe interfaces with a guest.
The imported headers are cleaned up a bit while importing them: some
part of the file that QEMU doesn't use are removed (description
of how to make hypercall in grant_table.h have been removed).
Other cleanup:
- xen-mapcache.c and xen-legacy-backend.c don't need grant_table.h.
- xenfb.c doesn't need event_channel.h.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-3-anthony.perard@citrix.com>
xen-mapcache.c doesn't needs params.h.
xen-hvm.c uses defines available in params.h but so is xen_common.h
which is included before. HVM_PARAM_* flags are only needed to make
xc_hvm_param_{get,set} calls so including only xenctrl.h, which is
where the definition the function is, should be enough.
(xenctrl.h does include params.h)
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190618112341.513-4-anthony.perard@citrix.com>
Avoid using a variable length array.
We allocate the `dirty_bitmap' buffer only once when we start tracking
for dirty bits.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190618112341.513-5-anthony.perard@citrix.com>
This patch introduces a poll callback for event channel fd-s and uses
this to invoke the channel callback function.
To properly support polling, it is necessary for the event channel callback
function to return a boolean saying whether it has done any useful work or
not. Thus xen_block_dataplane_event() is modified to directly invoke
xen_block_handle_requests() and the latter only returns true if it actually
processes any requests. This also means that the call to qemu_bh_schedule()
is moved into xen_block_complete_aio(), which is more intuitive since the
only reason for doing a deferred poll of the shared ring should be because
there were previously insufficient resources to fully complete a previous
poll.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-4-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds an AioContext parameter to xen_device_bind_event_channel()
and then uses aio_set_fd_handler() to set the callback rather than
qemu_set_fd_handler().
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-3-paul.durrant@citrix.com>
[Call aio_set_fd_handler() with is_external=true]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
To better support use of IOThread-s it will be necessary to be able to set
the AioContext for each XenEventChannel and hence it is necessary to open a
separate handle to libxenevtchan for each channel.
This patch stops using NotifierList for event channel callbacks, replacing
that construct by a list of complete XenEventChannel structures. Each of
these now has a xenevtchn_handle pointer in place of the single pointer
previously held in the XenDevice structure. The individual handles are
opened/closed in xen_device_bind/unbind_event_channel(), replacing the
single open/close in xen_device_realize/unrealize().
NOTE: This patch does not add an AioContext parameter to
xen_device_bind_event_channel(). That will be done in a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190408151617.13025-2-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A recent Xen commit [1] clarified the semantics of sector based quantities
used in the blkif protocol such that it is now safe to create a xen-block
device with a logical_block_size != 512, as long as the device only
connects to a frontend advertizing 'feature-large-block-size'.
This patch modifies xen-block accordingly. It also uses a stack variable
for the BlockBackend in xen_block_realize() to avoid repeated dereferencing
of the BlockConf pointer, and changes the parameters of
xen_block_dataplane_create() so that the BlockBackend pointer and sector
size are passed expicitly rather than implicitly via the BlockConf.
These modifications have been tested against a recent Windows PV XENVBD
driver [2] using a xen-disk device with a 4kB logical block size.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=commit;h=67e1c050e36b2c9900cca83618e56189effbad98
[2] https://winpvdrvbuild.xenproject.org:8080/job/XENVBD-master/126
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190409164038.25484-1-paul.durrant@citrix.com>
[Edited error message]
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity pointed out a memory leak in riscv_sifive_e_soc_realize(),
where a pair of recently added MemoryRegion instances would not be freed
if there were errors elsewhere in the function. The fix here is to
simply not use dynamic allocation for these instances: there's always
one of each in SiFiveESoCState, so instead we just include them within
the struct.
Fixes: 30efbf330a ("SiFive RISC-V GPIO Device")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The largest pci bus number should be calculated from ECAM size,
instead of its base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Writes to the SiFive PRCI registers are preserved while leaving the
ready bits set for the HFX/HFR oscillators and the lock bit set for the
PLL.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Commit c87759ce87 fixed a regression affecting pc-q35 machines by
introducing a new pc-q35-4.0.1 machine version to be used instead
of pc-q35-4.0. The only purpose was to revert the default behaviour
of not using split irqchip, but the change also introduced the usual
hw_compat and pc_compat bits, and wired them for pc-q35 only.
This raises questions when it comes to add new compat properties for
4.0* machine versions of any architecture. Where to add them ? In
4.0, 4.0.1 or both ? Error prone. Another possibility would be to teach
all other architectures about 4.0.1. This solution isn't satisfying,
especially since this is a pc-q35 specific issue.
It turns out that the split irqchip default is handled in the machine
option function and doesn't involve compat lists at all.
Drop all the 4.0.1 compat lists and use the 4.0 ones instead in the 4.0.1
machine option function.
Move the compat props that were added to the 4.0.1 since c87759ce87 to
4.0.
Even if only hw_compat_4_0_1 had an impact on other architectures,
drop pc_compat_4_0_1 as well for consistency.
Fixes: c87759ce87 "q35: Revert to kernel irqchip"
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <156051774276.244890.8660277280145466396.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Due to an off-by-one error, the assert statements allow an
out-of-bound array access. This doesn't happen in practice,
but the static analyzer notices.
Signed-off-by: Lidong Chen <lidong.chen@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <6b19cb7359a10a6bedc3ea0fce22fed3ef93c102.1560806687.git.lidong.chen@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Representing Hyper-V properties as bits will allow us to check features
and dependencies between them in a natural way.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv3 specification says that the GICD_TYPER.SecurityExtn bit
is RAZ if GICD_CTLR.DS is 1. We were incorrectly making it RAZ
if the security extension is unsupported. "Security extension
unsupported" always implies GICD_CTLR.DS == 1, but the guest can
also set DS on a GIC which does support the security extension.
Fix the condition to correctly check the GICD_CTLR.DS bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190524124248.28394-3-peter.maydell@linaro.org
The GIC ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524124248.28394-2-peter.maydell@linaro.org
The SSE-200 hardware has configurable integration settings which
determine whether its two CPUs have the FPU and DSP:
* CPU0_FPU (default 0)
* CPU0_DSP (default 0)
* CPU1_FPU (default 1)
* CPU1_DSP (default 1)
Similarly, the IoTKit has settings for its single CPU:
* CPU0_FPU (default 1)
* CPU0_DSP (default 1)
Of our four boards that use either the IoTKit or the SSE-200:
* mps2-an505, mps2-an521 and musca-a use the default settings
* musca-b1 enables FPU and DSP on both CPUs
Currently QEMU models all these boards using CPUs with
both FPU and DSP enabled. This means that we are incorrect
for mps2-an521 and musca-a, which should not have FPU or DSP
on CPU0.
Create QOM properties on the ARMSSE devices corresponding to the
default h/w integration settings, and make the Musca-B1 board
enable FPU and DSP on both CPUs. This fixes the mps2-an521
and musca-a behaviour, and leaves the musca-b1 and mps2-an505
behaviour unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-5-peter.maydell@linaro.org
Create "vfp" and "dsp" properties on the armv7m container object
which will be forwarded to its CPU object, so that SoCs can
configure whether the CPU has these features.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-4-peter.maydell@linaro.org
Since Linux v3.17, the kernel's Image header includes a field image_size,
which gives the total size of the kernel including unpopulated data
sections such as the BSS). If this is present, then return it from
load_aarch64_image() as the true size of the kernel rather than
just using the size of the Image file itself. This allows the code
which calculates where to put the initrd to avoid putting it in
the kernel's BSS area.
This means that we should be able to reliably load kernel images
which are larger than 128MB without accidentally putting the
initrd or dtb in locations that clash with the kernel itself.
Fixes: https://bugs.launchpad.net/qemu/+bug/1823998
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-5-peter.maydell@linaro.org
We currently put the initrd at the smaller of:
* 128MB into RAM
* halfway into the RAM
(with the dtb following it).
However for large kernels this might mean that the kernel
overlaps the initrd. For some kinds of kernel (self-decompressing
32-bit kernels, and ELF images with a BSS section at the end)
we don't know the exact size, but even there we have a
minimum size. Put the initrd at least further into RAM than
that. For image formats that can give us an exact kernel size, this
will mean that we definitely avoid overlaying kernel and initrd.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-4-peter.maydell@linaro.org
We calculate the locations in memory where we want to put the
initrd and the DTB based on the size of the kernel, since they
come after it. Add some explicit checks that these aren't off the
end of RAM entirely.
(At the moment the way we calculate the initrd_start means that
it can't ever be off the end of RAM, but that will change with
the next commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-3-peter.maydell@linaro.org
In the Arm kernel/initrd loading code, in some places we make the
incorrect assumption that info->ram_size can be treated as the
address of the end of RAM, as for instance when we calculate the
available space for the initrd using "info->ram_size - info->initrd_start".
This is wrong, because many Arm boards (including "virt") specify
a non-zero info->loader_start to indicate that their RAM area
starts at a non-zero physical address.
Correct the places which make this incorrect assumption.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-2-peter.maydell@linaro.org
This patch changes the handling of the mmconfig area. Thanks to the
pci(e) expander devices we already have the logic to exclude address
ranges from PCI0._CRS. We can simply add the mmconfig address range
to the list get it excluded as well.
With that in place we can go with a fixed pci hole which covers the
whole area from the end of (low) ram to the ioapic.
This will make the whole logic alot less fragile. No matter where the
firmware places the mmconfig xbar, things should work correctly. The
guest also gets a bit more PCI address space (seabios boot):
# cat /proc/iomem
[ ... ]
7ffdd000-7fffffff : reserved
80000000-afffffff : PCI Bus 0000:00 <<-- this is new
b0000000-bfffffff : PCI MMCONFIG 0000 [bus 00-ff]
b0000000-bfffffff : reserved
c0000000-febfffff : PCI Bus 0000:00
f8000000-fbffffff : 0000:00:01.0
[ ... ]
So this is a guest visible change.
Cc: László Érsek <lersek@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190607073429.3436-1-kraxel@redhat.com>
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When a guest which doesn't support multiqueue is migrated with a multi queues
vhost-user-blk deivce, a crash will occur like:
0 qemu_memfd_alloc (name=<value optimized out>, size=562949953421312, seals=<value optimized out>, fd=0x7f87171fe8b4, errp=0x7f87171fe8a8) at util/memfd.c:153
1 0x00007f883559d7cf in vhost_log_alloc (size=70368744177664, share=true) at hw/virtio/vhost.c:186
2 0x00007f88355a0758 in vhost_log_get (listener=0x7f8838bd7940, enable=1) at qemu-2-12/hw/virtio/vhost.c:211
3 vhost_dev_log_resize (listener=0x7f8838bd7940, enable=1) at hw/virtio/vhost.c:263
4 vhost_migration_log (listener=0x7f8838bd7940, enable=1) at hw/virtio/vhost.c:787
5 0x00007f88355463d6 in memory_global_dirty_log_start () at memory.c:2503
6 0x00007f8835550577 in ram_init_bitmaps (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2173
7 ram_init_all (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2192
8 ram_save_setup (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2219
9 0x00007f88357a419d in qemu_savevm_state_setup (f=0x7f88384ce600) at migration/savevm.c:1002
10 0x00007f883579fc3e in migration_thread (opaque=0x7f8837530400) at migration/migration.c:2382
11 0x00007f8832447893 in start_thread () from /lib64/libpthread.so.0
12 0x00007f8832178bfd in clone () from /lib64/libc.so.6
This is because vhost_get_log_size() returns a overflowed vhost-log size.
In this function, it uses the uninitialized variable vqs->used_phys and
vqs->used_size to get the vhost-log size.
Signed-off-by: Li Hangjing <lihangjing@baidu.com>
Reviewed-by: Xie Yongji <xieyongji@baidu.com>
Reviewed-by: Chai Wen <chaiwen@baidu.com>
Message-Id: <20190603061524.24076-1-lihangjing@baidu.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The uninitialized memory allocated for the command FIFO of the
floppy controller during the VM hardware initialization incurs
many unwanted reports by Valgrind when VM state is being saved.
That verbosity hardens a search for the real memory issues when
the iotests run. Particularly, the patch eliminates 20 unnecessary
reports of the Valgrind tool in the iotest #169.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-id: 1559154027-282547-1-git-send-email-andrey.shinkevich@virtuozzo.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The code used to assign an interrupt index/subindex to an
eventfd is duplicated many times. Let's introduce an helper that
allows to set/unset the signaling for an ACTION_TRIGGER,
ACTION_MASK or ACTION_UNMASK action.
In the error message, we now use errno in case of any
VFIO_DEVICE_SET_IRQS ioctl failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The MSI-X relocation code can sometimes be used to work around bogus
MSI-X capabilities, but this test for whether the PBA is outside of
the specified BAR causes the device to error before we can apply a
relocation. Let it proceed if we intend to relocate MSI-X anyway.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The resizable BAR capability is currently exposed read-only from the
kernel and we don't yet implement a protocol for virtualizing it to
the VM. Exposing it to the guest read-only introduces poor behavior
as the guest has no reason to test that a control register write is
accepted by the hardware. This can lead to cases where the guest OS
assumes the BAR has been resized, but it hasn't. This has been
observed when assigning AMD Vega GPUs.
Note, this does not preclude future enablement of resizable BARs, but
it's currently incorrect to expose this capability as read-only, so
better to not expose it at all.
Reported-by: James Courtier-Dutton <james.dutton@gmail.com>
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In commit 80376c3fc2 in 2010 we added a workaround for
some qbus buses not being connected to qdev devices -- if the
bus has no parent object then we register a reset function which
resets the bus on system reset (and unregister it when the
bus is unparented).
Nearly a decade later, we have now no buses in the tree which
are created with non-NULL parents, so we can remove the
workaround and instead just assert that if the bus has a NULL
parent then it is the main system bus.
(The absence of other parentless buses was confirmed by
code inspection of all the callsites of qbus_create() and
qbus_create_inplace() and cross-checked by 'make check'.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190523150543.22676-1-peter.maydell@linaro.org
The SMMUv3 ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190524124829.2589-1-peter.maydell@linaro.org
This is ostensibly to avoid the weirdness of len looking like it might
come from a guest and sometimes being used. While we are at it fix up
the error checking for the arm-linux-user implementation of the API
which got flagged up by Coverity (CID 1401700).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
-----BEGIN PGP SIGNATURE-----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=ERgu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190612' into staging
ppc patch queue 2019-06-12
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
# gpg: Signature made Wed 12 Jun 2019 06:47:56 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190612:
ppc/xive: Make XIVE generate the proper interrupt types
ppc/pnv: activate the "dumpdtb" option on the powernv machine
target/ppc: Use tcg_gen_gvec_bitsel
spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges
spapr: Direct all PCI hotplug to host bridge, rather than P2P bridge
spapr: Don't use bus number for building DRC ids
spapr: Clean up DRC index construction
spapr: Clean up spapr_drc_populate_dt()
spapr: Clean up dt creation for PCI buses
spapr: Clean up device tree construction for PCI devices
spapr: Clean up device node name generation for PCI devices
target/ppc: Fix lxvw4x, lxvh8x and lxvb16x
spapr_pci: Improve error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit d52c454aad "contrib: add vhost-user-gpu" and "c68082c43a
virtio-gpu: split virtio-gpu-pci & virtio-vga" created headers with
unusual header guard symbols. Clean them up
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190607141321.9726-1-armbru@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
It should be generic Hypervisor Virtualization interrupts for HV
directed rings and traditional External Interrupts for the OS directed
ring.
Don't generate anything for the user ring as it isn't actually
supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190606174409.12502-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a good way to debug the DT creation for current PowerNV
machines and new ones to come.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190606174732.13051-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine type already allows PCI hotplug and unplug via the
PAPR mechanism, but only on the root bus of each PHB. This patch extends
this to allow PCI to PCI bridges to be hotplugged, and devices to be
hotplugged or unplugged under P2P bridges.
For now we disallow hot unplugging P2P bridges. I tried doing that, but
haven't managed to get it working, I think due to some guest side problems
that need further investigation.
To do this we dynamically construct DRCs when bridges are hot (or cold)
added, which can in turn be used to hotplug devices under the bridge.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
A P2P bridge will attempt to handle the hotplug with SHPC, which doesn't
work in the PAPR environment. Instead we want to direct all PCI hotplug
actions to the PAPR specific host bridge which will use the PAPR hotplug
mechanism.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
DRC ids are more or less arbitrary, as long as they're consistent. For
PCI, we notionally build them from the phb's index along with PCI bus
number, slot and function number.
Using bus number is broken, however, because it can change if the guest
re-enumerates the PCI topology for whatever reason (e.g. due to hotplug
of a bridge, which we don't support yet but want to).
Fortunately, there's an alternative. Bridges are required to have a unique
non-zero "chassis number" that we can use instead. Adjust the code to
use that instead.
This looks like it would introduce a guest visible breaking change, but
in fact it does not because we don't yet ever use non-zero bus numbers.
Both chassis and bus number are always 0 for the root bus, so there's no
change for the existing cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_pci.c currently has several confusingly similarly named functions for
various conversions between representations of DRCs. Make things clearer
by renaming things in a more consistent XXX_from_YYY() manner and remove
some called-only-once variants in favour of open coding.
While we're at it, move this code together in the file to avoid some extra
forward references, and split out construction and removal of DRCs for the
host bridge into helper functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
This makes some minor cleanups to spapr_drc_populate_dt(), renaming it to
the shorter and more idiomatic spapr_dt_drc() along the way.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Device nodes for PCI bridges (both host and P2P) describe both the bridge
device itself and the bus hanging off it, handling of this is a bit of a
mess.
spapr_dt_pci_device() has a few things it only adds for non-bridges, but
always adds #address-cells and #size-cells which should only appear for
bridges. But the walking down the subordinate PCI bus is done in one of
its callers spapr_populate_pci_devices_dt(). The PHB dt creation in
spapr_populate_pci_dt() open codes some similar logic to the bridge case.
This patch consolidates things in a bunch of ways:
* Bus specific dt info is now created in spapr_dt_pci_bus() used for both
P2P bridges and the host bridge. This includes walking subordinate
devices
* spapr_dt_pci_device() now calls spapr_dt_pci_bus() when called on a
P2P bridge
* We do detection of bridges with the is_bridge field of the device class,
rather than checking PCI config space directly, for consistency with
qemu's core PCI code.
* Several things are renamed for brevity and clarity
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_create_pci_child_dt() is a trivial wrapper around
spapr_populate_pci_child_dt(), but is the latter's only caller. So fold
them together into spapr_dt_pci_device(), which closer matches our modern
naming convention.
While there, make a number of cleanups to the function itself. This is
mostly using more temporary locals to avoid awkwardly long lines, and in
some cases avoiding double reads of PCI config space variables.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_populate_pci_child_dt() adds a 'name' property to the device tree
node for PCI devices. This is never necessary for a flattened device tree,
it is implicit in the name added when the node is constructed. In fact
anything we do add to a 'name' property will be overwritten with something
derived from the structural name in the guest firmware (but in fact it is
exactly the same bytes).
So, remove that. In addition, pci_get_node_name() is very simple, so fold
it into its (also simple) sole caller spapr_create_pci_child_dt().
While we're there rename pci_find_device_name() to the shorter and more
accurate dt_name_from_class().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Every PHB must have a unique index. This is checked at realize but when
a duplicate index is detected, an error message mentioning BUIDs is
printed. This doesn't help much, especially since BUID is an internal
concept that is no longer exposed to the user.
Fix the message to mention the index property instead of BUID. As a bonus
print a list of indexes already in use.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155915010892.2061314.10485622810149098411.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-3-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
Cleanup in the boilerplate that each target must define.
Replace xtensa_env_get_cpu with env_archcpu. The combination
CPU(xtensa_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Move cpu_get_tb_cpu_state below the include of "exec/cpu-all.h"
so that the definition of env_cpu is available.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace uc32_env_get_cpu with env_archcpu. The combination
CPU(uc32_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace sparc_env_get_cpu with env_archcpu. The combination
CPU(sparc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace ppc_env_get_cpu with env_archcpu. The combination
CPU(ppc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace nios2_env_get_cpu with env_archcpu. The combination
CPU(nios2_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace mips_env_get_cpu with env_archcpu. The combination
CPU(mips_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace x86_env_get_cpu with env_archcpu. The combination
CPU(x86_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have both ArchCPU and CPUArchState, we can define
this generically instead of via macro in each target's cpu.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There's no functional change but the flow is (hopefully)
more consistent for both file and folder object types.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <20190401211712.19012-4-bsd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We don't care about the other two missing base features:
- S390_FEAT_DFP_PACKED_CONVERSION
- S390_FEAT_GROUP_GEN13_PTFF
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Fill the new QemuDmaBuf->modifier field properly from plane info.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 20190529072144.26737-3-kraxel@redhat.com
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc+B4YAAoJECgfDbjSjVRpq1EIAJR7tCxcpu9GggVlinmUA8G4
tmSAe06IryH7+nF3RsnINuGu7ius9qC2/E2y0uJUHhTqiU/RWOfWZ7PPM0EcYZaA
TLPaCe2NUF6/8afeqmvE9Usk7VspI5TDZRms+bonmZz2xP1lHIMN0qW4s7HHLWr8
sZKDtCJ+9cYII93VQwtlR0qiHgv5f0kzcuZeJaZHsAHH6XZGqRuQjI6txcFa4o53
lkdLCEwTnRuwu2wyL84eL5p+E8SzOgR/x1QI+nffrJfsvnmiT7lnOrkjnQlWAp5G
xqwqsUrUxUCuQ+zitwJqmv+H6nx79MwAM7fTHAETCWX703N5o9tZxAnHHqLoa8I=
=cQNg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: cleanups, features
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 05 Jun 2019 20:55:04 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
bios-tables-test: ignore identical binaries
tests: acpi: add simple arm/virt testcase
tests: add expected ACPI tables for arm/virt board
bios-tables-test: list all tables that differ
vhost-scsi: Allow user to enable migration
vhost-scsi: Add VMState descriptor
vhost-scsi: The vhost backend should be stopped when the VM is not running
bios-tables-test: add diff allowed list
vhost: fix memory leak in vhost_user_scsi_realize
vhost: fix incorrect print type
vhost: remove the dead code
docs: smbios: remove family=x from type2 entry description
pci: Fold pci_get_bus_devfn() into its sole caller
pci: Make is_bridge a bool
pcie: Simplify pci_adjust_config_limit()
acpi: pci: use build_append_foo() API to construct MCFG
hw/acpi: Consolidate build_mcfg to pci.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190528164020.32250-11-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190528164020.32250-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20190528164020.32250-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up, removing an extra space to please
checkpatch.pl):
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>.
Message-Id: <20190528164020.32250-7-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190528164020.32250-10-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20190528164020.32250-9-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <20190528164020.32250-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190528164020.32250-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <20190528164020.32250-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the BusState is accesible from the SCSIBus object,
it is pointless to use qbus_reset_all_fn.
Use qbus_reset_all() directly.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Message-Id: <20190528164020.32250-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
fix incorrect print type in vhost_virtqueue_stop
Signed-off-by: Jie Wang <wangjie88@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1556605773-42019-1-git-send-email-wangjie88@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is a trivial cleanup patch.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Kamal Heib <kheib@redhat.com>
Message-Id: <20190505105112.22691-1-yuval.shaia@oracle.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This makes use of qdev_prop_drive_iothread for scsi-disk so that the
disk can be attached to a node that is already in the target AioContext.
We need to check that the HBA actually supports iothreads, otherwise
scsi-disk must make sure that the node is already in the main
AioContext.
This changes the error message for conflicting iothread settings.
Previously, virtio-scsi produced the error message, now it comes from
blk_set_aio_context(). Update a test case accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some qdev block devices have support for iothreads and take care of the
AioContext they are running in, but most devices don't know about any of
this. For the latter category, the qdev drive property must make sure
that their BlockBackend is in the main AioContext.
Unfortunately, while the current code just does the same thing for
devices that do support iothreads, this is not correct and it would show
as soon as we actually try to keep a consistent AioContext assignment
across all nodes and users of a block graph subtree: If a node is
already in a non-default AioContext because of one of its users,
attaching a new device should still be possible if that device can work
in the same AioContext. Switching the node back to the main context
first and only then into the device AioContext causes failure (because
the existing user wouldn't allow the switch to the main context).
So devices that support iothreads need a different kind of drive
property that leaves the node in its current AioContext, but by using
this type, the device promises to check later that it can work with this
context.
This patch adds the qdev infrastructure that allows devices to signal
that they handle iothreads and qdev should leave the AioContext alone.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds a new parameter to blk_new() which requires its callers to
declare from which AioContext this BlockBackend is going to be used (or
the locks of which AioContext need to be taken anyway).
The given context is only stored and kept up to date when changing
AioContexts. Actually applying the stored AioContext to the root node
is saved for another commit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error parameter to blk_set_aio_context() and use
bdrv_child_try_set_aio_context() internally to check whether all
involved nodes can actually support the AioContext switch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kenneth Heitke <kenneth.heitke@intel.com>
Reviewed-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit b2fc91db84 ("q35: set split kernel irqchip as default") changed
the default for the pc-q35-4.0 machine type to use split irqchip, which
turned out to have disasterous effects on vfio-pci INTx support. KVM
resampling irqfds are registered for handling these interrupts, but
these are non-functional in split irqchip mode. We can't simply test
for split irqchip in QEMU as userspace handling of this interrupt is a
significant performance regression versus KVM handling (GeForce GPUs
assigned to Windows VMs are non-functional without forcing MSI mode or
re-enabling kernel irqchip).
The resolution is to revert the change in default irqchip mode in the
pc-q35-4.1 machine and create a pc-q35-4.0.1 machine for the 4.0-stable
branch. The qemu-q35-4.0 machine type should not be used in vfio-pci
configurations for devices requiring legacy INTx support without
explicitly modifying the VM configuration to use kernel irqchip.
Link: https://bugs.launchpad.net/qemu/+bug/1826422
Fixes: b2fc91db84 ("q35: set split kernel irqchip as default")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <155786484688.13873.6037015630912983760.stgit@gimli.home>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to have a test device created by the board.
Instead, create it in the qtest so that we will be able to run
it on other boards too.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The dma related variable dma.dst/src/cnt is dma_addr_t, it is
uint64_t in x64 platform. Change these usage from uint32_to
uint64_t to avoid trancation in edu_dma_timer.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190510164349.81507-4-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The edu spec says when address >= 0x80, the MMIO area can
be accessed by 64-bit.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20190510164349.81507-3-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The edu spec says the MMIO area can be accessed by 64-bit.
However currently the 'max_access_size' is not so the MMIO
access dispatch can only access 32-bit one time. This patch fixes
this to respect the spec.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daude <philmd@redhat.com>
Message-Id: <20190510164349.81507-2-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to perform a valid migration of a vhost-scsi device,
the following requirements must be met:
(1) The virtio-scsi device state needs to be saved & loaded.
(2) The vhost backend must be stopped before virtio-scsi device state
is saved:
(2.1) Sync vhost backend state to virtio-scsi device state.
(2.2) No further I/O requests are made by vhost backend to target
SCSI device.
(2.3) No further guest memory access takes place after VM is stopped.
(3) Requests in-flight to target SCSI device are completed before
migration handover.
(4) Target SCSI device state needs to be saved & loaded into the
destination host target SCSI device.
Previous commit ("vhost-scsi: Add VMState descriptor")
add support to save & load the device state using VMState.
This meets requirement (1).
When VM is stopped by migration thread (On Pre-Copy complete), the
following code path is executed:
migration_completion() -> vm_stop_force_state() -> vm_stop() ->
do_vm_stop().
do_vm_stop() calls first pause_all_vcpus() which pause all guest
vCPUs and then call vm_state_notify().
In case of vhost-scsi device, this will lead to the following code path
to be executed:
vm_state_notify() -> virtio_vmstate_change() ->
virtio_set_status() -> vhost_scsi_set_status() -> vhost_scsi_stop().
vhost_scsi_stop() then calls vhost_scsi_clear_endpoint() and
vhost_scsi_common_stop().
vhost_scsi_clear_endpoint() sends VHOST_SCSI_CLEAR_ENDPOINT ioctl to
vhost backend which will reach kernel's vhost_scsi_clear_endpoint()
which process all pending I/O requests and wait for them to complete
(vhost_scsi_flush()). This meets requirement (3).
vhost_scsi_common_stop() will stop the vhost backend.
As part of this stop, dirty-bitmap is synced and vhost backend state is
synced with virtio-scsi device state. As at this point guest vCPUs are
already paused, this meets requirement (2).
At this point we are left with requirement (4) which is target SCSI
device specific and therefore cannot be done by QEMU. Which is the main
reason why vhost-scsi adds a migration blocker.
However, as this can be handled either by an external orchestrator or
by using shared-storage (i.e. iSCSI), there is no reason to limit the
orchestrator from being able to explictly specify it wish to enable
migration even when VM have a vhost-scsi device.
Considering all the above, this commit allows orchestrator to explictly
specify that it is responsbile for taking care of requirement (4) and
therefore vhost-scsi should not add a migration blocker.
Reviewed-by: Nir Weiner <nir.weiner@oracle.com>
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190416125912.44001-4-liran.alon@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
As preparation of enabling migration of vhost-scsi device,
define it’s VMState. Note, we keep the convention of
verifying in the pre_save() method that the vhost backend
must be stopped before attempting to save the device
state. Similar to how it is done for vhost-vsock.
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Nir Weiner <nir.weiner@oracle.com>
Message-Id: <20190416125912.44001-3-liran.alon@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
vhost-scsi doesn’t takes into account whether the VM is running or not in
order to decide if it should start/stop vhost backend.
This would lead to vhost backend still being active when VM's RunState
suddenly change to stopped.
An example of when this issue is encountered is when Live-Migration Pre-Copy
phase completes. As in this case, VM state will be changed to stopped (while
vhost backend is still active), which will result in
virtio_vmstate_change() -> virtio_set_status() -> vhost_scsi_set_status()
executed but vhost_scsi_set_status() will just return without stopping
vhost backend.
To handle this, change code to consider that vhost processing should be
stopped when VM is not running. Similar to how it is done in vhost-vsock
device at vhost_vsock_set_status().
Fixes: 5e9be92d77 ("vhost-scsi: new device supporting the tcm_vhost Linux kernel module”)
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Nir Weiner <nir.weiner@oracle.com>
Message-Id: <20190416125912.44001-2-liran.alon@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
-----BEGIN PGP SIGNATURE-----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=2q3B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190529' into staging
ppc patch queue 2019-05-29
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
# gpg: Signature made Wed 29 May 2019 07:49:04 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190529: (44 commits)
ppc/pnv: add dummy XSCOM registers for PRD initialization
ppc/pnv: introduce new skiboot platform properties
spapr: Don't migrate the hpt_maxpagesize cap to older machine types
spapr: change default interrupt mode to 'dual'
spapr/xive: fix multiple resets when using the 'dual' interrupt mode
docs: provide documentation on the POWER9 XIVE interrupt controller
spapr/irq: add KVM support to the 'dual' machine
ppc/xics: fix irq priority in ics_set_irq_type()
spapr/irq: initialize the IRQ device only once
spapr/irq: introduce a spapr_irq_init_device() helper
spapr: check for the activation of the KVM IRQ device
spapr: introduce routines to delete the KVM IRQ device
sysbus: add a sysbus_mmio_unmap() helper
spapr/xive: activate KVM support
spapr/xive: add migration support for KVM
spapr/xive: introduce a VM state change handler
spapr/xive: add state synchronization with KVM
spapr/xive: add hcall support when under KVM
spapr/xive: add KVM support
spapr: Print out extra hints when CAS negotiation of interrupt mode fails
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
fix memory leak in vhost_user_scsi_realize
Signed-off-by: Jie Wang <wangjie88@huawei.com>
Message-Id: <1556608500-12183-1-git-send-email-wangjie88@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
fix incorrect print type in vhost_virtqueue_stop
Signed-off-by: Jie Wang <wangjie88@huawei.com>
Message-Id: <1556605773-42019-1-git-send-email-wangjie88@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
remove the dead code
Signed-off-by: Jie Wang <wangjie88@huawei.com>
Message-Id: <1556604614-32081-1-git-send-email-wangjie88@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The only remaining caller of pci_get_bus_devfn() is pci_nic_init_nofail(),
itself an old compatibility function. Fold the two together to avoid
re-using the stale interface.
While we're there replace the explicit fprintf()s with error_report().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513061939.3464-6-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
The is_bridge field in PCIDevice acts as a bool, but is declared as an int.
Declare it as a bool for clarity, and change everything that writes it to
use true/false instead of 0/1 to match.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-5-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since c2077e2c "pci: Adjust PCI config limit based on bus topology",
pci_adjust_config_limit() has been used in the config space read and write
paths to only permit access to extended config space on buses which permit
it. Specifically it prevents access on devices below a vanilla-PCI bus via
some combination of bridges, even if both the host bridge and the device
itself are PCI-E.
It accomplishes this with a somewhat complex call up the chain of bridges
to see if any of them prohibit extended config space access. This is
overly complex, since we can always know if the bus will support such
access at the point it is constructed.
This patch simplifies the test by using a flag in the PCIBus instance
indicating whether extended configuration space is accessible. It is
false for vanilla PCI buses. For PCI-E buses, it is true for root
buses and equal to the parent bus's's capability otherwise.
For the special case of sPAPR's paravirtualized PCI root bus, which
acts mostly like vanilla PCI, but does allow extended config space
access, we override the default value of the flag from the host bridge
code.
This should cause no behavioural change.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
build_append_foo() API doesn't need explicit endianness conversions
which eliminates a source of errors and it makes build_mcfg() look like
declarative definition of MCFG table in ACPI spec, which makes it easy
to review.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v3:
* add some comment on the Configuration Space base address allocation
structure
v2:
* miss the reserved[8] of MCFG in last version, add it back
* drop SOBs and make sure bios-tables-test all OK
Message-Id: <20190521062836.6541-3-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
s/kbd/tablet/, fixes cut+paste bug.
Cc: qemu-stable@nongnu.org
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190520081805.15019-1-kraxel@redhat.com
Add support for per port power switching.
Virtual power of course ;)
Use port-power=on property to enable this.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-6-kraxel@redhat.com
Helper function to update port status bits which depends on the
connected device. We need the same logic for device attach and
port reset, so factor it out.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524070310.4952-5-kraxel@redhat.com
Add usb_hub_port_set() and usb_hub_port_clear() helpers which care about
updating the change bits (port->wPortChange) properly, so we don't need
to have that logic sprinkled all over the place ;)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-4-kraxel@redhat.com
Add num_ports property which allows configure the number of downstream
ports. Valid range is 1-8, default is 8.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-3-kraxel@redhat.com
Add dashes, so they don't look like two separate things when printed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524070310.4952-2-kraxel@redhat.com
Seems some devices become confused when we call
libusb_set_configuration(). So before calling the function check
whenever the device has multiple configurations in the first place, and
in case it hasn't (which is the case for the majority of devices) simply
skip the call as it will have no effect anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-4-kraxel@redhat.com
If the guest didn't talk to the device yet, skip the reset.
Without this usb-host devices get resetted a number of times
at boot time for no good reason.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-3-kraxel@redhat.com
That way the device reset handler can see what
the before-reset state of the device is.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-2-kraxel@redhat.com
Add new virtio-gpu devices with a "vhost-user" property. The
associated vhost-user backend is used to handle the virtio rings and
provide rendering results thanks to the vhost-user-gpu protocol.
Example usage:
-object vhost-user-backend,id=vug,cmd="./vhost-user-gpu"
-device vhost-user-vga,vhost-user=vug
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-10-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add base classes that are common to vhost-user-gpu-pci and
vhost-user-vga.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-9-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a base class that is common to virtio-gpu and vhost-user-gpu
devices.
The VirtIOGPUBase base class provides common functionalities necessary
for both virtio-gpu and vhost-user-gpu:
- common configuration (max-outputs, initial resolution, flags)
- virtio device initialization, including queue setup
- device pre-conditions checks (iommu)
- migration blocker
- virtio device callbacks
- hooking up to qemu display subsystem
- a few common helper functions to reset the device, retrieve display
informations
- a class callback to unblock the rendering (for GL updates)
What is left to the virtio-gpu subdevice to take care of, in short,
are all the virtio queues handling, command processing and migration.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-8-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This will allow to share the format conversion function with
vhost-user-gpu.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The helper functions are useful to build the vhost-user-gpu backend.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a new vhost-user message to give a unix socket to a vhost-user
backend for GPU display updates.
Back when I started that work, I added a new GPU channel because the
vhost-user protocol wasn't bidirectional. Since then, there is a
vhost-user-slave channel for the slave to send requests to the master.
We could extend it with GPU messages. However, the GPU protocol is
quite orthogonal to vhost-user, thus I chose to have a new dedicated
channel.
See vhost-user-gpu.rst for the protocol details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
PRD (Processor recovery diagnostics) is a service available on
OpenPower systems. The opal-prd daemon initializes the PowerPC
Processor through the XSCOM bus and then waits for hardware diagnostic
events.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190527071722.31424-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Newer skiboots (after 6.3) support QEMU platforms that have
characteristics closer to real OpenPOWER systems. The CPU type is used
to define the BMC drivers: Aspeed AST2400 for POWER8 processors and
AST2500 for POWER9s.
Advertise the new platform property names, "qemu,powernv8" and
"qemu,powernv9", using the CPU type chosen for the QEMU PowerNV
machine. Also, advertise the original platform name "qemu,powernv" in
case of POWER8 processors for compatibility with older skiboots.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190527071749.31499-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 0b8c89be7f7b added the hpt_maxpagesize capability to the migration
stream. This is okay for new machine types but it breaks backward migration
to older QEMUs, which don't expect the extra subsection.
Add a compatibility boolean flag to the sPAPR machine class and use it to
skip migration of the capability for machine types 4.0 and older. This
fixes migration to an older QEMU. Note that the destination will emit a
warning:
qemu-system-ppc64: warning: cap-hpt-max-page-size lower level (16) in incoming stream than on destination (24)
This is expected and harmless though. It is okay to migrate from a lower
HPT maximum page size (64k) to a greater one (16M).
Fixes: 0b8c89be7f7b "spapr: Add forgotten capability to migration stream"
Based-on: <20190522074016.10521-3-clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155853262675.1158324.17301777846476373459.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that XIVE support is complete (QEMU emulated and KVM devices),
change the pseries machine to advertise both interrupt modes: XICS
(P7/P8) and XIVE (P9).
The machine default interrupt modes depends on the version. Current
settings are:
pseries default interrupt mode
4.1 dual
4.0 xics
3.1 xics
3.0 legacy xics (different IRQ number space layout)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190522074016.10521-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a reset occurs on a pseries machine using the 'dual'
interrupt mode, the KVM devices are released and recreated depending
on the interrupt mode selected by CAS. If XIVE is selected, the SysBus
memory regions of the SpaprXive model are initialized by the KVM
backend initialization routine each time a reset occurs. This leads to
a crash after a couple of resets because the machine reaches the
QDEV_MAX_MMIO limit of SysBusDevice :
qemu-system-ppc64: hw/core/sysbus.c:193: sysbus_init_mmio: Assertion `dev->num_mmio < QDEV_MAX_MMIO' failed.
To fix, initialize the SysBus memory regions in spapr_xive_realize()
called only once and remove the same inits from the QEMU and KVM
backend initialization routines which are called at each reset.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190522074016.10521-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt mode is chosen by the CAS negotiation process and
activated after a reset to take into account the required changes in
the machine. This brings new constraints on how the associated KVM IRQ
device is initialized.
Currently, each model takes care of the initialization of the KVM
device in their realize method but this is not possible anymore as the
initialization needs to be done globaly when the interrupt mode is
known, i.e. when machine is reseted. It also means that we need a way
to delete a KVM device when another mode is chosen.
Also, to support migration, the QEMU objects holding the state to
transfer should always be available but not necessarily activated.
The overall approach of this proposal is to initialize both interrupt
mode at the QEMU level to keep the IRQ number space in sync and to
allow switching from one mode to another. For the KVM side of things,
the whole initialization of the KVM device, sources and presenters, is
grouped in a single routine. The XICS and XIVE sPAPR IRQ reset
handlers are modified accordingly to handle the init and the delete
sequences of the KVM device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Recent commits changed the behavior of ics_set_irq_type() to
initialize correctly LSIs at the KVM level. ics_set_irq_type() is also
called by the realize routine of the different devices of the machine
when initial interrupts are claimed, before the ICSState device is
reseted.
In the case, the ICSIRQState priority is 0x0 and the call to
ics_set_irq_type() results in configuring the target of the
interrupt. On P9, when using the KVM XICS-on-XIVE device, the target
is configured to be server 0, priority 0 and the event queue 0 is
created automatically by KVM.
With the dual interrupt mode creating the KVM device at reset, it
leads to unexpected effects on the guest, mostly blocking IPIs. This
is wrong, fix it by reseting the ICSIRQState structure when
ics_set_irq_type() is called.
Fixes: commit 6cead90c5c ("xics: Write source state to KVM at claim time")
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a check to make sure that the routine initializing the emulated
IRQ device is called once. We don't have much to test on the XICS
side, so we introduce a 'init' boolean under ICSState.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The way the XICS and the XIVE devices are initialized follows the same
pattern. First, try to connect to the KVM device and if not possible
fallback on the emulated device, unless a kernel_irqchip is required.
The spapr_irq_init_device() routine implements this sequence in
generic way using new sPAPR IRQ handlers ->init_emu() and ->init_kvm().
The XIVE init sequence is moved under the associated sPAPR IRQ
->init() handler. This will change again when KVM support is added for
the dual interrupt mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The activation of the KVM IRQ device depends on the interrupt mode
chosen at CAS time by the machine and some methods used at reset or by
the migration need to be protected.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a new interrupt mode is chosen by CAS, the machine generates a
reset to reconfigure. At this point, the connection with the previous
KVM device needs to be closed and a new connection needs to opened
with the KVM device operating the chosen interrupt mode.
New routines are introduced to destroy the XICS and the XIVE KVM
devices. They make use of a new KVM device ioctl which destroys the
device and also disconnects the IRQ presenters from the vCPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used to remove the MMIO regions of the POWER9 XIVE
interrupt controller when the sPAPR machine is reseted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All is in place for KVM now. State synchronization and migration will
come next.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the VM is stopped, the VM state handler stabilizes the XIVE IC
and marks the EQ pages dirty. These are then transferred to destination
before the transfer of the device vmstates starts.
The SpaprXive interrupt controller model captures the XIVE internal
tables, EAT and ENDT and the XiveTCTX model does the same for the
thread interrupt context registers.
At restart, the SpaprXive 'post_load' method restores all the XIVE
states. It is called by the sPAPR machine 'post_load' method, when all
XIVE states have been transferred and loaded.
Finally, the source states are restored in the VM change state handler
when the machine reaches the running state.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This handler is in charge of stabilizing the flow of event notifications
in the XIVE controller before migrating a guest. This is a requirement
before transferring the guest EQ pages to a destination.
When the VM is stopped, the handler sets the source PQs to PENDING to
stop the flow of events and to possibly catch a triggered interrupt
occuring while the VM is stopped. Their previous state is saved. The
XIVE controller is then synced through KVM to flush any in-flight
event notification and to stabilize the EQs. At this stage, the EQ
pages are marked dirty to make sure the EQ pages are transferred if a
migration sequence is in progress.
The previous configuration of the sources is restored when the VM
resumes, after a migration or a stop. If an interrupt was queued while
the VM was stopped, the handler simply generates the missing trigger.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This extends the KVM XIVE device backend with 'synchronize_state'
methods used to retrieve the state from KVM. The HW state of the
sources, the KVM device and the thread interrupt contexts are
collected for the monitor usage and also migration.
These get operations rely on their KVM counterpart in the host kernel
which acts as a proxy for OPAL, the host firmware. The set operations
will be added for migration support later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
XIVE hcalls are all redirected to QEMU as none are on a fast path.
When necessary, QEMU invokes KVM through specific ioctls to perform
host operations. QEMU should have done the necessary checks before
calling KVM and, in case of failure, H_HARDWARE is simply returned.
H_INT_ESB is a special case that could have been handled under KVM
but the impact on performance was low when under QEMU. Here are some
figures :
kernel irqchip OFF ON
H_INT_ESB KVM QEMU
rtl8139 (LSI ) 1.19 1.24 1.23 Gbits/sec
virtio 31.80 42.30 -- Gbits/sec
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This introduces a set of helpers when KVM is in use, which create the
KVM XIVE device, initialize the interrupt sources at a KVM level and
connect the interrupt presenters to the vCPU.
They also handle the initialization of the TIMA and the source ESB
memory regions of the controller. These have a different type under
KVM. They are 'ram device' memory mappings, similarly to VFIO, exposed
to the guest and the associated VMAs on the host are populated
dynamically with the appropriate pages using a fault handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's suggest to the user how the machine should be configured to allow
the guest to boot successfully.
Suggested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155799221739.527449.14907564571096243745.stgit@bahia.lan>
Reviewed-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Tested-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
[dwg: Adjusted for style error]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When we added support for NVLink2 passthrough devices, we changed the
phb_placement hook to handle the placement of NVLink2 bridges' specific
resources. For compatibility we use a version that doesn't do this
allocation for old machine types.
However, because of the delay between when the patch was posted and when
it was merged, we ended up with that compatibility hook applying for
machine versions 3.1 and earlier whereas it should apply for 4.0 and
earlier (since the patch was applied early in the 4.1 tree).
Fixes: ec132efaa8 "spapr: Support NVIDIA V100 GPU with NVLink2"
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
spapr machine capabilities are supposed to be sent in the migration stream
so that we can sanity check the source and destination have compatible
configuration. Unfortunately, when we added the hpt-max-page-size
capability, we forgot to add it to the migration state. This means that we
can generate spurious warnings when both ends are configured for large
pages, or potentially fail to warn if the source is configured for huge
pages, but the destination is not.
Fixes: 2309832afd "spapr: Maximum (HPT) pagesize property"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The processor stop status and control register (PSSCR) is used to
control the power saving facilities of the thread. The exit criterion
bit (EC) is used to specify whether the thread should be woken by any
interrupt (EC == 0) or only an interrupt enabled in the LPCR to wake the
thread (EC == 1).
The rtas facilities start-cpu and self-stop are used to transition a
vcpu between the stopped and running states. When a vcpu is stopped it
may only be started again by the start-cpu rtas call.
Currently a vcpu in the stopped state will start again whenever an
interrupt comes along due to PSSCR_EC being cleared, and while this is
architecturally correct for a hardware thread, a vcpu is expected to
only be woken by calling start-cpu. This means when performing a reboot
on a tcg machine that the secondary threads will restart while the
primary is still in slof, this is unsupported and causes call traces
like:
SLOF **********************************************************************
QEMU Starting
Build Date = Jan 14 2019 18:00:39
FW Version = git-a5b428e1c1eae703
Press "s" to enter Open Firmware.
qemu: fatal: Trying to deliver HV exception (MSR) 70 with no HV support
NIP 6d61676963313230 LR 000000003dbe0308 CTR 6d61676963313233 XER 0000000000000000 CPU#1
MSR 0000000000000000 HID0 0000000000000000 HF 0000000000000000 iidx 3 didx 3
TB 00000026 115746031956 DECR 18446744073326238463
GPR00 000000003dbe0308 000000003e669fe0 000000003dc10700 0000000000000003
GPR04 000000003dc62198 000000003dc62178 000000003dc0ea48 0000000000000030
GPR08 000000003dc621a8 0000000000000018 000000003e466008 000000003dc50700
GPR12 c00000000093a4e0 c00000003ffff300 c00000003e533f90 0000000000000000
GPR16 0000000000000000 0000000000000000 000000003e466010 000000003dc0b040
GPR20 0000000000008000 000000000000f003 0000000000000006 000000003e66a050
GPR24 000000003dc06400 000000003dc0ae70 0000000000000003 000000000000f001
GPR28 000000003e66a060 ffffffffffffffff 6d61676963313233 0000000000000028
CR 28000222 [ E L - - - E E E ] RES ffffffffffffffff
FPR00 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPR04 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPR08 0000000000000000 0000000000000000 0000000000000000 00000000311825e0
FPR12 00000000311825e0 0000000000000000 0000000000000000 0000000000000000
FPR16 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPR20 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPR24 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPR28 0000000000000000 0000000000000000 0000000000000000 0000000000000000
FPSCR 0000000000000000
SRR0 000000003dbe06b0 SRR1 0000000000080000 PVR 00000000004e1200 VRSAVE 0000000000000000
SPRG0 000000003dbe0308 SPRG1 000000003e669fe0 SPRG2 00000000000000d8 SPRG3 000000003dbe0308
SPRG4 0000000000000000 SPRG5 0000000000000000 SPRG6 0000000000000000 SPRG7 0000000000000000
HSRR0 6d61676963313230 HSRR1 0000000000000000
CFAR 000000003dbe3e64
LPCR 0000000004020008
PTCR 0000000000000000 DAR 0000000000000000 DSISR 0000000000000000
Aborted (core dumped)
To fix this, set the PSSCR_EC bit when a vcpu is stopped to disable it
from coming back online until the start-cpu rtas call is made.
Fixes: 21c0d66a9c ("target/ppc: Fix support for "STOP light" states on POWER9")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190516005744.24366-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a machine is started with ic-mode=xive but the guest only knows
about XICS, eg. an RHEL 7.6 guest, the kernel panics. This is
expected but a bit unfortunate since the crash doesn't provide
much information for the end user to guess what's happening.
Detect that during CAS and exit QEMU with a proper error message
instead, like it is already done for the MMU.
Even if this is less likely to happen, the opposite case of a guest
that only knows about XIVE would certainly fail all the same if the
machine is started with ic-mode=xics.
Also, the only valid values a guest can pass in byte 23 of OV5 during
CAS are 0b00 (XIVE legacy mode) and 0b01 (XIVE exploitation mode). Any
other value is a bug, at least with the current spec. Again, it does
not seem right to let the guest go on without a precise idea of the
interrupt mode it asked for.
Handle these cases as well.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155793986451.464434.12887933000007255549.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of LISN i.e "Logical Interrupt Source Number" as per
Xive PAPR document "info pic" prints as LSIN, let's fix it.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Message-Id: <20190509080750.21999-1-sathnaga@linux.vnet.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This proved to be a useful information when debugging issues with OS
event queues allocated above 64GB.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-4-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The high order bits of the address of the OS event queue is stored in
bits [4-31] of word2 of the XIVE END internal structures and the low
order bits in word3. This structure is using Big Endian ordering and
computing the value requires some simple arithmetic which happens to
be wrong. The mask removing bits [0-3] of word2 is applied to the
wrong value and the resulting address is bogus when above 64GB.
Guests with more than 64GB of RAM will allocate pages for the OS event
queues which will reside above the 64GB limit. In this case, the XIVE
device model will wake up the CPUs in case of a notification, such as
IPIs, but the update of the event queue will be written at the wrong
place in memory. The result is uncertain as the guest memory is
trashed and IPI are not delivered.
Introduce a helper xive_end_qaddr() to compute this value correctly in
all places where it is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>