This is the combination of frozen bit and counter type, on a per
counter basis. So far this is only used by HFLAGS_INSN_CNT, but
will be used more later.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[danielhb: fixed PMC4 cyc_cnt shift, insn run latch code,
MMCR0_FC handling, "PMC[1-6]" comment]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220103224746.167831-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PMU is already counting cycles by calculating time elapsed in
nanoseconds. Counting instructions is a different matter and requires
another approach.
This patch adds the capability of counting completed instructions (Perf
event PM_INST_CMPL) by counting the amount of instructions translated in
each translation block right before exiting it.
A new pmu_count_insns() helper in translation.c was added to do that.
After verifying that the PMU is counting instructions, call
helper_insns_inc(). This new helper from power8-pmu.c will add the
instructions to the relevant counters. It'll also be responsible for
triggering counter negative overflows as it is already being done with
cycles.
To verify whether the PMU is counting instructions or now, a new hflags
named 'HFLAGS_INSN_CNT' is introduced. This flag will match the internal
state of the PMU. We're be using this flag to avoid calling
helper_insn_inc() when we do not have a valid instruction event being
sampled.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211201151734.654994-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We're going to add PMU support for TCG PPC64 chips, based on IBM POWER8+
emulation and following PowerISA v3.1. This requires several PMU related
registers to be exposed to userspace (problem state). PowerISA v3.1
dictates that the PMCC bits of the MMCR0 register controls the level of
access of the PMU registers to problem state.
This patch start things off by exposing both PMCC bits to hflags,
allowing us to access them via DisasContext in the read/write callbacks
that we're going to add next.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211018010133.315842-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a Host Radix field (hr) in DisasContext with LPCR[HR] value to allow
us to decide between Radix and HPT while validating instructions
arguments. Note that PowerISA v3.1 does not require LPCR[HR] and PATE.HR
to match if the thread is in ultravisor/hypervisor real addressing mode,
so ctx->hr may be invalid if ctx->hv and ctx->dr are set.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210917114751.206845-2-matheus.ferst@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
moved store_40x_sler from mmu_common.c to helper_regs.c as it is
a function to store a value in a special purpose register, so
moving it to a file focused in special register manipulation
is more appropriate.
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Message-Id: <20210723175627.72847-4-lucas.araujo@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Verify that hflags was updated correctly whenever we change
cpu state that is used by hflags.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-11-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We weren't recording MSR_GS in hflags, which means that BookE
memory accesses were essentially random vs Guest State.
Instead of adding this bit directly, record the completed mmu
indexes instead. This makes it obvious that we are recording
exactly the information that we need.
This also means that we can stop directly recording MSR_IR.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-9-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Nothing within the translator -- or anywhere else for that
matter -- checks MSR_SA or MSR_AP on the 602. This may be
a mistake. However, for the moment, we need not record these
bits in hflags.
This allows us to simplify HFLAGS_VSX computation by moving
it to overlap with MSR_VSX.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-8-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because this bit was not in hflags, the privilege check
for tlb instructions was essentially random.
Recompute hflags when storing to LPCR.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-7-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because these bits were not in hflags, the code generated
for single-stepping on BookE was essentially random.
Recompute hflags when storing to dbcr0.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-5-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Copying flags directly from msr has drawbacks: (1) msr bits
mean different things per cpu, (2) msr has 64 bits on 64 cpus
while tb->flags has only 32 bits.
Create a enum to define these bits. Document the origin of each bit
and validate those bits that must match MSR. This fixes the
truncation of env->hflags to tb->flags, because we no longer
have hflags bits set above bit 31.
Most of the code in ppc_tr_init_disas_context is moved over to
hreg_compute_hflags. Some of it is simple extractions from msr,
some requires examining other cpu flags. Anything that is moved
becomes a simple extract from hflags in ppc_tr_init_disas_context.
Several existing bugs are left in ppc_tr_init_disas_context, where
additional changes are required -- to be addressed in future patches.
Remove a broken #if 0 block.
Reported-by: Ivan Warren <ivan@vmfacility.fr>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210323184340.619757-3-richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We have eliminated all normal uses of hflags_nmsr. We need
not even compute it except when we want to migrate. Rename
the field to emphasize this.
Remove the fixme comment for migrating access_type. This value
is only ever used with the current executing instruction, and
is never live when the cpu is halted for migration.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210315184615.1985590-6-richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Keep all hflags computation in one place, as this will be
especially important later.
Introduce a new POWERPC_FLAG_HID0_LE bit to indicate when
LE should be taken from HID0. This appears to be set if
and only if POWERPC_FLAG_RTC_CLK is set, but we're not
short of bits and having both names will avoid confusion.
Note that this was the only user of hflags_nmsr, so we can
perform a straight assignment rather than mask and set.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210315184615.1985590-3-richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move the functions to a new file, helper_regs.c.
Note int_helper.c was relying on helper_regs.h to
indirectly include qemu/log.h.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210315184615.1985590-2-richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
