Connect CAN0 and CAN1 on the ZynqMP.
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-3-git-send-email-fnu.vikram@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accroding to the SMMUv3 spec, the SPAN field of Level1 Stream Table
Descriptor is 5 bits([4:0]).
Fixes: 9bde7f0674f(hw/arm/smmuv3: Implement translate callback)
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Message-id: 20201124023711.1184-1-jiangkunkun@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an eeprom device and fill it with fru
information
$ ipmitool fru print 0
Product Manufacturer : Bytedance
Product Name : G220A
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201210103607.556-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On the AST2600A1, the SRAM size was increased to 89KB.
Fixes: 7582591ae7 ("aspeed: Support AST2600A1 silicon revision")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201112012113.835858-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
G220A is a 2 socket x86 motherboard supported by OpenBMC.
Strapping configuration was obtained from hardware.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201122105134.671-2-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If table size is changed between virt_acpi_build and
virt_acpi_build_update, the table size would not be updated to
UEFI, therefore, just align the size to 128kb, which is enough
and same with x86. It would warn if 64k is not enough and the
align size should be updated.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-7-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resources of pxbs are obtained by crs_build and the resources
used by pxbs would be moved from the resources defined for host-bridge.
The resources for pxb are composed of following two parts:
1. The bar space of the pci-bridge/pcie-root-port behined it
2. The config space of devices behind it.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add bus property to virt machine for primary PCI root bus and use it to add
extra pci roots behind it.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This way we can tell between regular IOMMUTLBEntry (entry of IOMMU
hardware) and notifications.
In the notifications, we set explicitly if it is a MAPs or an UNMAP,
instead of trusting in entry permissions to differentiate them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Previous name didn't reflect the iommu operation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We should use printf format specifier "%u" instead of "%i" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 5F9FD78B.8000300@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The removal of the selection of A15MPCORE from ARM_VIRT also
removed what A15MPCORE selects, ARM_GIC. We still need ARM_GIC.
Fixes: bec3c97e0c ("hw/arm/virt: Remove dependency on Cortex-A15 MPCore peripherals")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201111143440.112763-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nseries machines have a codepath that allows them to load a
secondary bootloader. This code wasn't checking that the
load_image_targphys() succeeded. Check the return value and report
the error to the user.
While we're in the vicinity, fix the comment style of the
comment documenting what this image load is doing.
Fixes: Coverity CID 1192904
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201103114918.11807-1-peter.maydell@linaro.org
We don't need to fill the full pic[] array if we only use
few of the interrupt lines. Directly call qdev_get_gpio_in()
when necessary.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MusicPal board code connects both of the IRQ outputs of the UART
to the same INTC qemu_irq. Connecting two qemu_irqs outputs directly
to the same input is not valid as it produces subtly wrong behaviour
(for instance if both the IRQ lines are high, and then one goes
low, the INTC input will see this as a high-to-low transition
even though the second IRQ line should still be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
omap2420_mpu_init() introduced in commit 827df9f3c5 ("Add basic
OMAP2 chip support") takes care of creating the 3 UARTs.
Then commit 58a26b477e ("Emulate a serial bluetooth HCI with H4+
extensions and attach to n8x0's UART") added n8x0_uart_setup()
which create the UART and connects it to an IRQ output,
overwritting the existing peripheral and its IRQ connection.
This is incorrect.
Fortunately we don't need to fix this, because commit 6da68df7f9
("hw/arm/nseries: Replace the bluetooth chardev with a "null"
chardev") removed the use of this peripheral. We can simply
remove the code.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can use one MPC per SRAM bank, but we currently only wire the
IRQ from the first expansion MPC to the IRQ splitter. Fix that.
Fixes: bb75e16d5e ("hw/arm/iotkit: Wire up MPC interrupt lines")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using a Cortex-A15, the Virt machine does not use any
MPCore peripherals. Remove the dependency.
Fixes: 7951c7b7c0 ("hw/arm: Express dependencies of the virt machine with Kconfig")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201107114852.271922-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 32bd322a01 ("hw/timer/armv7m_systick: Rewrite to use ptimers")
changed armv7m_systick to build on ptimers. Make sure we have ptimers
in the build when building armv7m_systick.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201104103343.30392-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting a CPU with EL3 using the -kernel flag, set up CPTR_EL3 so
that SVE will not trap to EL3.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030151541.11976-1-remi@remlab.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BIT_ULL() macro to ensure we use 64-bit arithmetic.
This fixes the following Coverity issue (OVERFLOW_BEFORE_WIDEN):
CID 1432363 (#1 of 1): Unintentional integer overflow:
overflow_before_widen:
Potentially overflowing expression 1 << scale with type int
(32 bits, signed) is evaluated using 32-bit arithmetic, and
then used in a context that expects an expression of type
hwaddr (64 bits, unsigned).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201030144617.1535064-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
-----BEGIN PGP SIGNATURE-----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=igPS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20201028' into staging
ppc patch queue 2020-10-28
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
# gpg: Signature made Tue 27 Oct 2020 14:13:21 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20201028:
ppc/: fix some comment spelling errors
spapr: Improve spapr_reallocate_hpt() error reporting
target/ppc: Fix kvmppc_load_htab_chunk() error reporting
spapr: Use error_append_hint() in spapr_reallocate_hpt()
spapr: Simplify error handling in spapr_memory_plug()
spapr: Pass &error_abort when getting some PC DIMM properties
spapr: Use appropriate getter for PC_DIMM_SLOT_PROP
spapr: Use appropriate getter for PC_DIMM_ADDR_PROP
pc-dimm: Drop @errp argument of pc_dimm_plug()
spapr: Simplify spapr_cpu_core_realize() and spapr_cpu_core_unrealize()
spapr: Make spapr_cpu_core_unrealize() idempotent
spapr: Drop spapr_delete_vcpu() unused argument
spapr: Unrealize vCPUs with qdev_unrealize()
spapr: Fix leak of CPU machine specific data
spapr: Move spapr_create_nvdimm_dr_connectors() to core machine code
hw/net: move allocation to the heap due to very large stack frame
ppc/spapr: re-assert IRQs during event-scan if there are pending
spapr: Clarify why DR connectors aren't user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pc_dimm_plug() doesn't use it. It only aborts on error.
Drop @errp and adapt the callers accordingly.
[dwg: Removed unused label to fix compile]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309728447.2739814.12831204841251148202.stgit@bahia.lan>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Included the newly implemented SBSA generic watchdog device model into
SBSA platform
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201027015927.29495-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 'uart-out' clock from the CPRMAN to the PL011 instance.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN (clock controller) was mapped at the watchdog/power manager
address. It was also split into two unimplemented peripherals (CM and
A2W) but this is really the same one, as shown by this extract of the
Raspberry Pi 3 Linux device tree:
watchdog@7e100000 {
compatible = "brcm,bcm2835-pm\0brcm,bcm2835-pm-wdt";
[...]
reg = <0x7e100000 0x114 0x7e00a000 0x24>;
[...]
};
[...]
cprman@7e101000 {
compatible = "brcm,bcm2835-cprman";
[...]
reg = <0x7e101000 0x2000>;
[...]
};
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use of 0x%d - make up our mind as 0x%x
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201014193355.53074-1-dgilbert@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi 3A+ is a stripped down version of the 3B:
- 512 MiB of RAM instead of 1 GiB
- no on-board ethernet chipset
Add it as it is a closer match to what we model.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Similarly to the Pi A, the Pi Zero uses a BCM2835 SoC (ARMv6Z core).
The only difference between the revision 1.2 and 1.3 is the latter
exposes a CSI camera connector. As we do not implement the Unicam
peripheral, there is no point in exposing a camera connector :)
Therefore we choose to model the 1.2 revision.
Example booting the machine using content from [*]:
$ qemu-system-arm -M raspi0 -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-zero.dtb \
-append 'printk.time=0 earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Zero
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi A is almost the first machine released.
It uses a BCM2835 SoC which includes a ARMv6Z core.
Example booting the machine using content from [*]
(we use the device tree from the B model):
$ qemu-system-arm -M raspi1ap -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-b-plus.dtb \
-append 'earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Model B+
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The realize() function is clearly composed of two parts,
each described by a comment:
void realize()
{
/* common peripherals from bcm2835 */
...
/* bcm2836 interrupt controller (and mailboxes, etc.) */
...
}
Split the two part, so we can reuse the common part with other
SoCs from this family.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It makes no sense to set enabled-cpus=0 on single core SoCs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 has only one core. Introduce the core_count field to
be able to use values different than BCM283X_NCPUS (4).
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove usage of TypeInfo::class_data. Instead fill the fields in
the corresponding class_init().
So far all children use the same values for almost all fields,
but we are going to add the BCM2711/BCM2838 SoC for the raspi4
machine which use different fields.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No code out of bcm2836.c uses (or requires) the BCM283XInfo
declarations. Move it locally to the C source file.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure the vSMMUv3 will be restored before all PCIe devices so that DMA
translation can work properly during migration.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20201019091508.197-1-yuzenghui@huawei.com
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch sets min_cpus field for xlnx-versal-virt platform,
because it always creates XLNX_VERSAL_NR_ACPUS cpus even with
-smp 1 command line option.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 160343854912.8460.17915238517799132371.stgit@pasha-ThinkPad-X280
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When compiling with -Werror=implicit-fallthrough, gcc complains about
missing fallthrough annotations in this file. Looking at the code,
the fallthrough is very likely intended here, so add some comments
to silence the compiler warnings.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201020105938.23209-1-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The recently added LED device reports LED status changes with
the 'led_set_intensity' trace event. It is less invasive than
the fprintf() calls. We need however to have a binary built
with tracing support.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-8-f4bug@amsat.org>
The Witherspoon has 3 LEDs connected to a PCA9552. Add them.
The names and reset values are taken from:
https://github.com/open-power/witherspoon-xml/blob/master/witherspoon.xml
Example booting obmc-phosphor-image:
$ qemu-system-arm -M witherspoon-bmc -trace led_change_intensity
1592693373.997015:led_change_intensity LED desc:'front-fault-4' color:green intensity 0% -> 100%
1592693373.997632:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693373.998239:led_change_intensity LED desc:'front-id-5' color:green intensity 0% -> 100%
1592693500.291805:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693500.312041:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693500.821254:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693501.331517:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693501.841367:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693502.350839:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693502.861134:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693503.371090:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
We notice the front-power LED starts to blink at a ~2Hz rate.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200912134041.946260-5-f4bug@amsat.org>
Commit 7998beb9c2 removed the ram_size initialization in the
arm_boot_info structure, however it is used by arm_load_kernel().
Initialize the field to fix:
$ qemu-system-arm -M n800 -append 'console=ttyS1' \
-kernel meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0
qemu-system-arm: kernel 'meego-arm-n8x0-1.0.80.20100712.1431-vmlinuz-2.6.35~rc4-129.1-n8x0' is too large to fit in RAM (kernel size 1964608, RAM size 0)
Noticed while running the test introduced in commit 050a82f0c5
("tests/acceptance: Add a test for the N800 and N810 arm machines").
Fixes: 7998beb9c2 ("arm/nseries: use memdev for RAM")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201019095148.1602119-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SYS_timer is not directly wired to the ARM core, but to the
SoC (peripheral) interrupt controller.
Fixes: 0e5bbd7406 ("hw/arm/bcm2835_peripherals: Use the SYS_timer")
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While APEI is a generic ACPI feature (usable by X86 and ARM64), only
the 'virt' machine uses it, by enabling the RAS Virtualization. See
commit 2afa8c8519: "hw/arm/virt: Introduce a RAS machine option").
Restrict the APEI tables generation code to the single user: the virt
machine. If another machine wants to use it, it simply has to 'select
ACPI_APEI' in its Kconfig.
Fixes: aa16508f1d ("ACPI: Build related register address fields via hardware error fw_cfg blob")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201008161414.2672569-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The time to transmit a char is expressed in nanoseconds, not in ticks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201014213601.205222-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We add the kvm-steal-time CPU property and implement it for machvirt.
A tiny bit of refactoring was also done to allow pmu and pvtime to
use the same vcpu device helper functions.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the KVM PMU setup part of fdt_add_pmu_nodes() to
virt_cpu_post_init(), which is a more appropriate location. Now
fdt_add_pmu_nodes() is also named more appropriately, because it
no longer does anything but fdt node creation.
No functional change intended.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-5-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We'll add more to this new function in coming patches so we also
state the gic must be created and call it below create_gic().
No functional change intended.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-4-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Original commit did not allocate IRQs for the SMMUv3 in the irqmap
effectively using irq 0->3 (shared with other devices). Assuming
original intent was to allocate unique IRQs then add an allocation
to the irqmap.
Fixes: e9fdf45324 ("hw/arm: Add arm SBSA reference machine, devices part")
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201007100732.4103790-3-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SMMUv3 has an error in a previous patch where an i was transposed to a 1
meaning interrupts would not have been correctly assigned to the SMMUv3
instance.
Fixes: 48ba18e6d3 ("hw/arm/sbsa-ref: Simplify by moving the gic in the machine state")
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201007100732.4103790-2-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Make isar_feature_aa32_fp16_arith() handle M-profile
* Fix SVE splice
* Fix SVE LDR/STR
* Remove ignore_memory_transaction_failures on the raspi2
* raspi: Various cleanup/refactoring
-----BEGIN PGP SIGNATURE-----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=vKOh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201001' into staging
target-arm queue:
* Make isar_feature_aa32_fp16_arith() handle M-profile
* Fix SVE splice
* Fix SVE LDR/STR
* Remove ignore_memory_transaction_failures on the raspi2
* raspi: Various cleanup/refactoring
# gpg: Signature made Thu 01 Oct 2020 15:46:47 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201001:
hw/arm/raspi: Remove use of the 'version' value in the board code
hw/arm/raspi: Use RaspiProcessorId to set the firmware load address
hw/arm/raspi: Introduce RaspiProcessorId enum
hw/arm/raspi: Use more specific machine names
hw/arm/raspi: Avoid using TypeInfo::class_data pointer
hw/arm/raspi: Move arm_boot_info structure to RaspiMachineState
hw/arm/raspi: Load the firmware on the first core
hw/arm/raspi: Display the board revision in the machine description
hw/arm/raspi: Remove ignore_memory_transaction_failures on the raspi2
hw/arm/bcm2835: Add more unimplemented peripherals
hw/arm/raspi: Define various blocks base addresses
target/arm: Fix SVE splice
target/arm: Fix sve ldr/str
target/arm: Make isar_feature_aa32_fp16_arith() handle M-profile
target/arm: Add ID register values for Cortex-M0
hw/intc/armv7m_nvic: Only show ID register values for Main Extension CPUs
target/arm: Move id_pfr0, id_pfr1 into ARMISARegisters
target/arm: Replace ARM_FEATURE_PXN with ID_MMFR0.VMSA check
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We expected the 'version' ID to match the board processor ID,
but this is not always true (for example boards with revision
id 0xa02042/0xa22042 are Raspberry Pi 2 with a BCM2837 SoC).
This was not important because we were not modelling them, but
since the recent refactor now allow to model these boards, it
is safer to check the processor id directly. Remove the version
check.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The firmware load address depends on the SoC ("processor id") used,
not on the version of the board.
Suggested-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we only support a reduced set of the REV_CODE_PROCESSOR id
encoded in the board revision, define the PROCESSOR_ID values
as an enum. We can simplify the board_soc_type and cores_count
methods.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we can instantiate different machines based on their
board_rev register value, we can have various raspi2 and raspi3.
In commit fc78a990ec we corrected the machine description.
Correct the machine names too. For backward compatibility, add
an alias to the previous generic name.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using class_data pointer to create a MachineClass is not
the recommended way anymore. The correct way is to open-code
the MachineClass::fields in the class_init() method.
We can not use TYPE_RASPI_MACHINE::class_base_init() because
it is called *before* each machine class_init(), therefore the
board_rev field is not populated. We have to manually call
raspi_machine_class_common_init() for each machine.
This partly reverts commit a03bde3674.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The arm_boot_info structure belong to the machine,
move it to RaspiMachineState.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'first_cpu' is more a QEMU accelerator-related concept
than a variable the machine requires to use.
Since the machine is aware of its CPUs, directly use the
first one to load the firmware.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Display the board revision in the machine description.
Before:
$ qemu-system-aarch64 -M help | fgrep raspi
raspi2 Raspberry Pi 2B
raspi3 Raspberry Pi 3B
After:
raspi2 Raspberry Pi 2B (revision 1.1)
raspi3 Raspberry Pi 3B (revision 1.2)
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200924111808.77168-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 1c3db49d39 added the raspi3, which uses the same peripherals
than the raspi2 (but with different ARM cores). The raspi3 was
introduced without the ignore_memory_transaction_failures flag.
Almost 2 years later, the machine is usable running U-Boot and
Linux.
In commit 00cbd5bd74 we mapped a lot of unimplemented devices,
commit d442d95f added thermal block and commit 0e5bbd7406 the
system timer.
As we are happy with the raspi3, let's remove this flag on the
raspi2.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200921034729.432931-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bcm2835-v3d is used since Linux 4.7, see commit
49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree"),
and the bcm2835-txp since Linux 4.19, see commit
b7dd29b401f5 ("ARM: dts: bcm283x: Add Transposer block").
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20200921034729.432931-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fill gpex config struct from memory map, then call the new
acpi_dsdt_add_gpex helper function. No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-4-kraxel@redhat.com
It is defined twice already. Move to a common header file to
remove duplication and make it available to everybody.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-2-kraxel@redhat.com
Several callers of load_elf() pass pointers for lowaddr and highaddr
parameters which are then not used for anything. This may stem from a
misunderstanding that load_elf need a value here but in fact it can
take NULL to ignore these values. Remove such unused variables and
pass NULL instead from callers that don't need these.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20200705174020.BDD0174633F@zero.eik.bme.hu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200921221045.699690-20-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* Couple of cleanups
* New machine properties to define the flash models
-----BEGIN PGP SIGNATURE-----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=jN+V
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200918' into staging
Aspeed patches :
* Couple of cleanups
* New machine properties to define the flash models
# gpg: Signature made Fri 18 Sep 2020 08:23:19 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200918:
misc: aspeed_scu: Update AST2600 silicon id register
hw/arm/aspeed: Add machine properties to define the flash models
hw/arm/aspeed: Map the UART5 device unconditionally
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some machines don't have much differences a part from the flash model
being used. Introduce new machine properties to change them from the
command line.
For instance, to start the ast2500-evb machine with a different FMC
chip and a 64M SPI chip, use :
-M ast2500-evb,fmc-model=mx25l25635e,spi-model=mx66u51235f
Cc: 郁雷 <yulei.sh@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Lei YU <yulei.sh@bytedance.com>
Message-Id: <20200915054859.2338477-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The UART5 is present on the machine regardless there is a
character device connected to it. Map it unconditionally.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200905212415.760452-1-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When booting directly into a kernel, bypassing the boot loader, the CPU and
UART clocks are not set up correctly. This makes the system appear very
slow, and causes the initrd boot test to fail when optimization is off.
The UART clock must run at 24 MHz. The default 25 MHz reference clock
cannot achieve this, so switch to PLL2/2 @ 480 MHz, which works
perfectly with the default /20 divider.
The CPU clock should run at 800 MHz, so switch it to PLL1/2. PLL1 runs
at 800 MHz by default, so we need to double the feedback divider as well
to make it run at 1600 MHz (so PLL1/2 runs at 800 MHz).
We don't bother checking for PLL lock because we know our emulated PLLs
lock instantly.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-13-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows these NPCM7xx-based boards to boot from a flash image, e.g.
one built with OpenBMC. For example like this:
IMAGE=${OPENBMC}/build/tmp/deploy/images/gsj/image-bmc
qemu-system-arm -machine quanta-gsj -nographic \
-drive file=${IMAGE},if=mtd,bus=0,unit=0,format=raw,snapshot=on
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200911052101.2602693-12-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements a device model for the NPCM7xx SPI flash controller.
Direct reads and writes, and user-mode transactions have been tested in
various modes. Protection features are not implemented yet.
All the FIU instances are available in the SoC's address space,
regardless of whether or not they're connected to actual flash chips.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-11-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This just implements the bare minimum to cause the boot block to skip
memory initialization.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-10-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports reading and writing OTP fuses and keys. Only fuse reading
has been tested. Protection is not implemented.
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-9-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If a -bios option is specified on the command line, load the image into
the internal ROM memory region, which contains the first instructions
run by the CPU after reset.
If -bios is not specified, the vbootrom included with qemu is loaded by
default.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-8-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds two new machines, both supported by OpenBMC:
- npcm750-evb: Nuvoton NPCM750 Evaluation Board.
- quanta-gsj: A board with a NPCM730 chip.
They rely on the NPCM7xx SoC device to do the heavy lifting. They are
almost completely identical at the moment, apart from the SoC type,
which currently only changes the reset contents of one register
(GCR.MDLR), but they might grow apart a bit more as more functionality
is added.
Both machines can boot the Linux kernel into /bin/sh.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-6-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct the GEMs tx/rx clocks to use the 125Mhz fixed-clock.
This matches the setup with the fixed-link 100Mbit PHY.
It also avoids the following warnings from the Linux kernel
driver:
eth0: unable to generate target frequency: 125000000 Hz
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200909174647.662864-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a model of the MPS2 with the AN500 firmware. This is
similar to the AN385, with the following differences:
* Cortex-M7 CPU
* PSRAM is at 0x6000_0000
* Ethernet is at 0xa000_0000
* No zbt_boot_ctrl remapping of the low 16K
(but QEMU doesn't implement this anyway)
* no "block RAM" at 0x01000000
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200903202048.15370-3-peter.maydell@linaro.org
Implement a model of the MPS2 with the AN386 firmware. This is
essentially identical to the AN385 firmware, but it has a
Cortex-M4 rather than a Cortex-M3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200903202048.15370-2-peter.maydell@linaro.org
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
Let's make this file compilable with -Werror=implicit-fallthrough :
Looking at the code, it seems like the fallthrough is intended here,
so we should add the corresponding "/* fallthrough */" comment here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200911121844.404434-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When cadence_gem model was created for Xilinx boards, the PHY address
was hard-coded to 23 in the GEM model. Now that we have introduced a
property we can use that to tell GEM model what our PHY address is.
Change all boards' GEM 'phy-addr' property value to 23, and set the
PHY address default value to 0 in the GEM model.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
All Meson executables should specify their dependencies explicitly, either
directly or indirectly via declare_dependency. Makefiles instead did
not propagate dependencies correctly from static libraries, for example.
Therefore, flags for dependencies need not be included in QEMU_CFLAGS.
LIBS is not used at all, so drop that one as well.
In a few cases the dependencies were not yet specified, so add them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the previously created sbsa-ec device to the sbsa-ref machine in
secure memory so the PSCI implementation in ARM-TF can access it, but
not expose it to non secure firmware or OS except by via ARM-TF.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
Tested-by: Leif Lindholm <leif@nuviainc.com>
Message-id: 20200826141952.136164-3-graeme@nuviainc.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sbsa-ref platform uses a minimal device tree to pass amount of memory
as well as number of cpus to the firmware. However, when dumping that
minimal dtb (with -M sbsa-virt,dumpdtb=<file>), the resulting blob
generates a warning when decompiled by dtc due to lack of reg property.
Add a simple reg property per cpu, representing a 64-bit MPIDR_EL1.
This also ends up being cleaner than having the firmware calculating its
own IDs for generating APCI.
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200827124335.30586-1-leif@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BMC Firmware can be downloaded from :
https://www.supermicro.com/en/products/motherboard/X11SSL-F
Signed-off-by: Erik Smit <erik.lucas.smit@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: Prettified Erik's name in email
Modified commit log ]
Message-Id: <20200715173418.186-1-erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TYPE_ARM_SSE is a TYPE_SYS_BUS_DEVICE subclass, but
ARMSSEClass::parent_class is declared as DeviceClass.
It never caused any problems by pure luck:
We were not setting class_size for TYPE_ARM_SSE, so class_size of
TYPE_SYS_BUS_DEVICE was being used (sizeof(SysBusDeviceClass)).
This made the system allocate enough memory for TYPE_ARM_SSE
devices even though ARMSSEClass was too small for a sysbus
device.
Additionally, the ARMSSEClass::info field ended up at the same
offset as SysBusDeviceClass::explicit_ofw_unit_address. This
would make sysbus_get_fw_dev_path() crash for the device.
Luckily, sysbus_get_fw_dev_path() never gets called for
TYPE_ARM_SSE devices, because qdev_get_fw_dev_path() is only used
by the boot device code, and TYPE_ARM_SSE devices don't appear at
the fw_boot_order list.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200826181006.4097163-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Fix by calling qdev_connect_clock_in() before realizing.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we want to call qdev_connect_clock_in() before the device
is realized, we need to uninline cadence_uart_create() first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The H3 SoC keeps using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814122907.27732-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The A10 and H3 SoC keep using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814110057.307-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
We keep using the system_memory address space, but via the
proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200814125533.4047-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixing a typo in a previous patch that translated an "i" to a 1
and therefore breaking the allocation of PCIe interrupts. This was
discovered when virtio-net-pci devices ceased to function correctly.
Cc: qemu-stable@nongnu.org
Fixes: 48ba18e6d3 ("hw/arm/sbsa-ref: Simplify by moving the gic in the machine state")
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200821083853.356490-1-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename TYPE_ARMSSE to TYPE_ARM_SSE, and ARMSSE*() type checking
macros to ARM_SSE*().
This will avoid a future conflict between an ARM_SSE() type
checking macro and the ARMSSE typedef name.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-26-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros:
ASPEED_GPIO
ASPEED_I2C
ASPEED_RTC
ASPEED_SCU
ASPEED_SDHCI
ASPEED_SDMC
ASPEED_VIC
ASPEED_WDT
ASPEED_XDMA
This needs to be addressed to allow us to transform the QOM type
check macros into functions generated by OBJECT_DECLARE_TYPE().
Rename all the constants to ASPEED_DEV_*, to avoid conflicts.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (AW_H3_CCU, AW_H3_SYSCTRL). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to AW_H3_DEV_*, to avoid conflicts.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On ARM/virt machine type QEMU currently reports an incorrect _UID in
ACPI.
The particular node in question is the primary PciRoot (PCI0 in ACPI),
which gets assigned PCI0 in ACPI UID and 0 in the
DevicePath. This is due to the _UID assigned to it by build_dsdt in
hw/arm/virt-acpi-build.c Which does not correspond to the primary PCI
identifier given by pcibus_num in hw/pci/pci.c
In UEFI v2.8, section "10.4.2 Rules with ACPI _HID and _UID" ends with
the paragraph,
Root PCI bridges will use the plug and play ID of PNP0A03, This will
be stored in the ACPI Device Path _HID field, or in the Expanded
ACPI Device Path _CID field to match the ACPI name space. The _UID
in the ACPI Device Path structure must match the _UID in the ACPI
name space.
(See especially the last sentence.)
A similar bug has been reported on i386, on that architecture it has
been reported to confuse at least macOS which uses ACPI UIDs to build
the DevicePath for NVRAM boot options, while OVMF firmware gets them via
an internal channel through QEMU. When UEFI firmware and ACPI have
different values, this makes the underlying operating system unable to
report its boot option.
Cc: qemu-stable@nongnu.org
Reported-by: Vitaly Cheptsov <vit9696@protonmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Expose the RIL bit so that the guest driver uses range
invalidation. Although RIL is a 3.2 features, We let
the AIDR advertise SMMUv3.1 support as v3.x implementation
is allowed to implement features from v3.(x+1).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-12-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HAD is a mandatory features with SMMUv3.1 if S1P is set, which is
our case. Other 3.1 mandatory features come with S2P which we don't
have.
So let's support HAD and advertise SMMUv3.1 support in AIDR.
HAD support allows the CD to disable hierarchical attributes, ie.
if the HAD0/1 bit is set, the APTable field of table descriptors
walked through TTB0/1 is ignored.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the support for AIDR register. It currently advertises
SMMU V3.0 spec.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMU IIDR register is at 0x018 offset.
Fixes: 10a83cb988 ("hw/arm/smmuv3: Skeleton")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-9-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enhance the smmu_iotlb_inv_iova() helper with range invalidation.
This uses the new fields passed in the NH_VA and NH_VAA commands:
the size of the range, the level and the granule.
As NH_VA and NH_VAA both use those fields, their decoding and
handling is factorized in a new smmuv3_s1_range_inval() helper.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's introduce an helper for S1 IOVA range invalidation.
This will be used for NH_VA and NH_VAA commands. It decodes
the same fields, trace, calls the UNMAP notifiers and
invalidate the corresponding IOTLB entries.
At the moment, we do not support 3.2 range invalidation yet.
So it reduces to a single IOVA invalidation.
Note the leaf bit now is also decoded for the CMD_TLBI_NH_VAA
command. At the moment it is only used for tracing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment each entry in the IOTLB corresponds to a page sized
mapping (4K, 16K or 64K), even if the page belongs to a mapped
block. In case of block mapping this unefficiently consumes IOTLB
entries.
Change the value of the entry so that it reflects the actual
mapping it belongs to (block or page start address and size).
Also the level/tg of the entry is encoded in the key. In subsequent
patches we will enable range invalidation. This latter is able
to provide the level/tg of the entry.
Encoding the level/tg directly in the key will allow to invalidate
using g_hash_table_remove() when num_pages equals to 1.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-6-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a specialized SMMUTLBEntry to store the result of
the PTW and cache in the IOTLB. This structure extends the
generic IOMMUTLBEntry struct with the level of the entry and
the granule size.
Those latter will be useful when implementing range invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-5-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the smmu_get_iotlb_key() helper and the
SMMU_IOTLB_ASID() macro. Also move smmu_get_iotlb_key and
smmu_iotlb_key_hash in the IOTLB related code section.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add two helpers: one to lookup for a given IOTLB entry and
one to insert a new entry. We also move the tracing there.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Page and block PTE decoding can share some code. Let's
first handle table PTE and factorize some code shared by
page and block PTEs.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200728150815.11446-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
-----BEGIN PGP SIGNATURE-----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=Pefc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/sd-next-20200821' into staging
SD/MMC patches
- Convert legacy SD host controller to the SDBus API
- Move legacy API to a separate "sdcard_legacy.h" header
- Introduce methods to access multiple bytes on SDBus data lines
- Fix 'switch function' group location
- Fix SDSC maximum card size (2GB)
CI jobs result:
https://gitlab.com/philmd/qemu/-/pipelines/180605963
# gpg: Signature made Fri 21 Aug 2020 18:27:50 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/sd-next-20200821: (23 commits)
hw/sd: Correct the maximum size of a Standard Capacity SD Memory Card
hw/sd: Fix incorrect populated function switch status data structure
hw/sd: Use sdbus_read_data() instead of sdbus_read_byte() when possible
hw/sd: Add sdbus_read_data() to read multiples bytes on the data line
hw/sd: Use sdbus_write_data() instead of sdbus_write_byte when possible
hw/sd: Add sdbus_write_data() to write multiples bytes on the data line
hw/sd: Rename sdbus_read_data() as sdbus_read_byte()
hw/sd: Rename sdbus_write_data() as sdbus_write_byte()
hw/sd: Rename read/write_data() as read/write_byte()
hw/sd: Move sdcard legacy API to 'hw/sd/sdcard_legacy.h'
hw/sd/sdcard: Make sd_data_ready() static
hw/sd/pl181: Replace disabled fprintf()s by trace events
hw/sd/pl181: Do not create SD card within the SD host controller
hw/sd/pl181: Expose a SDBus and connect the SDCard to it
hw/sd/pl181: Use named GPIOs
hw/sd/pl181: Add TODO to use Fifo32 API
hw/sd/pl181: Rename pl181_send_command() as pl181_do_command()
hw/sd/pl181: Replace fprintf(stderr, "*\n") with error_report()
hw/sd/milkymist: Do not create SD card within the SD host controller
hw/sd/milkymist: Create the SDBus at init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :) Let the machine/board
model create and plug the SD cards when required.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-8-f4bug@amsat.org>
To make the code easier to manage/review/use, rename the
cardstatus[0] variable as 'card_readonly' and name the GPIO
"card-read-only".
Similarly with cardstatus[1], renamed as 'card_inserted' and
name its GPIO "card-inserted".
Adapt the users accordingly by using the qdev_init_gpio_out_named()
function.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705204630.4133-6-f4bug@amsat.org>
SD/MMC host controllers provide a SD Bus to plug SD cards,
but don't come with SD card plugged in :)
The machine/board object is where the SD cards are created.
Since the PXA2xx is not qdevified, for now create the cards
in pxa270_init() which is the SoC model.
In the future we will move this to the board model.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200705213350.24725-2-f4bug@amsat.org>
Each architecture's sourceset is placed in an hw_arch dictionary, and picked up
from there when building the per-emulator static_library.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add 5.2 machine types for arm/i440fx/q35/s390x/spapr.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200819144016.281156-1-cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The nrf51 SoC model wasn't setting the system_clock_scale
global.which meant that if guest code used the systick timer in "use
the processor clock" mode it would hang because time never advances.
Set the global to match the documented CPU clock speed for this SoC.
This SoC in fact doesn't have a SysTick timer (which is the only thing
currently that cares about the system_clock_scale), because it's
a configurable option in the Cortex-M0. However our Cortex-M0 and
thus our nrf51 and our micro:bit board do provide a SysTick, so
we ought to provide a functional one rather than a broken one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200727193458.31250-1-peter.maydell@linaro.org
The MSF2 SoC model and the Stellaris board code both wire
SYSRESETREQ up to a function that just invokes
qemu_system_reset_request(SHUTDOWN_CAUSE_GUEST_RESET);
This is now the default action that the NVIC does if the line is
not connected, so we can delete the handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-4-peter.maydell@linaro.org
The netduino2 and netduinoplus2 boards forgot to set the system_clock_scale
global, which meant that if guest code used the systick timer in "use
the processor clock" mode it would hang because time never advances.
Set the global to match the documented CPU clock speed of these boards.
Judging by the data sheet this is slightly simplistic because the
SoC allows configuration of the SYSCLK source and frequency via the
RCC (reset and clock control) module, but we don't model that.
Fixes: https://bugs.launchpad.net/qemu/+bug/1876187
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200727162617.26227-1-peter.maydell@linaro.org
When booting an EL3 cpu with -kernel, we set up EL3 and then
drop down to EL2. We need to enable access to v8.5-MemTag
tag allocation at EL3 before doing so.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200724163853.504655-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting an EL3 cpu with -kernel, we set up EL3 and then
drop down to EL2. We need to enable access to v8.3-PAuth
keys and instructions at EL3 before doing so.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200724163853.504655-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The USB_DWC2 switch is currently "default y", so it is included in all
qemu-system-* builds, even if it is not needed. Even worse, it does a
"select USB", so USB devices are now showing up as available on targets
that do not support USB at all. This sysbus device should only be
included by the boards that need it, i.e. by the Raspi machines.
Fixes: 153ef1662c ("dwc-hsotg (dwc2) USB host controller emulation")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Paul Zimmerman <pauldzim@gmail.com>
Message-id: 20200722154719.10130-1-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
object_get_canonical_path_component() returns a malloced copy of a
property name on success, null on failure.
19 of its 25 callers immediately free the returned copy.
Change object_get_canonical_path_component() to return the property
name directly. Since modifying the name would be wrong, adjust the
return type to const char *.
Drop the free from the 19 callers become simpler, add the g_strdup()
to the other six.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
nd_table[] contains NIC configuration for boards to pick up. Device
code has no business looking there. Several devices do it anyway.
Two of them already have a suitable FIXME comment: "allwinner-a10" and
"msf2-soc". Copy it to the others: "allwinner-h3", "xlnx-versal",
"xlnx,zynqmp", "sparc32-ledma", "riscv.sifive.u.soc".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200715140440.3540942-3-armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Watch this:
$ qemu-system-aarch64 -M ast2600-evb -S -display none -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 0, "major": 5}, "package": "v5.0.0-2464-g3a9163af4e"}, "capabilities": ["oob"]}}
{"execute": "qmp_capabilities"}
{"return": {}}
{"execute": "device-list-properties", "arguments": {"typename": "msf2-soc"}}
Unsupported NIC model: ftgmac100
armbru@dusky:~/work/images$ echo $?
1
This is what breaks "make check SPEED=slow".
Root cause is m2sxxx_soc_initfn()'s messing with nd_table[] via
qemu_check_nic_model(). That's wrong.
We fixed the exact same bug for device "allwinner-a10" in commit
8aabc5437b "hw/arm/allwinner-a10: Do not use nd_table in instance_init
function". Fix this instance the same way: move the offending code to
m2sxxx_soc_realize(), where it's less wrong, and add a FIXME comment.
Fixes: 05b7374a58 ("msf2: Add EMAC block to SmartFusion2 SoC")
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200715140440.3540942-2-armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In armsse_realize() we have a loop over [0, info->num_cpus), which
indexes into various fixed-size arrays in the ARMSSE struct. This
confuses Coverity, which warns that we might overrun those arrays
(CID 1430326, 1430337, 1430371, 1430414, 1430430). This can't
actually happen, because the info struct is always one of the entries
in the armsse_variants[] array and num_cpus is either 1 or 2; we also
already assert in armsse_init() that num_cpus is not too large.
However, adding an assert to armsse_realize() like the one in
armsse_init() should help Coverity figure out that these code paths
aren't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200713143716.9881-1-peter.maydell@linaro.org
When MTE is enabled, tag memory must exist for all RAM.
It might be possible to simultaneously hot plug tag memory
alongside the corresponding normal memory, but for now just
disable hotplug.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While we expect KVM to support MTE at some future point,
it certainly won't be ready in time for qemu 5.1.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Control this cpu feature via a machine property, much as we do
with secure=on, since both require specialized support in the
machine setup to be functional.
Default MTE to off, since this feature implies extra overhead.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200713213341.590275-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We use "create_simple" names for functions that allocate, initialize,
configure and realize device objects: pci_create_simple(),
isa_create_simple(), usb_create_simple(). For consistency, rename
i2c_create_slave() as i2c_slave_create_simple(). Since we have
to update all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-5-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The other i2c functions are called i2c_slave_FOO(). Rename as
i2c_slave_realize_and_unref() to be consistent.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-4-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We use "new" names for functions that allocate and initialize
device objects: pci_new(), isa_new(), usb_new().
Let's call this one i2c_slave_new(). Since we have to update
all the callers, also let it return a I2CSlave object.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-3-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
All the callers of aspeed_i2c_get_bus() have a AspeedI2CState and
cast it to a DeviceState with DEVICE(), then aspeed_i2c_get_bus()
cast the DeviceState to an AspeedI2CState with ASPEED_I2C()...
Simplify aspeed_i2c_get_bus() callers by using AspeedI2CState
argument.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200705224154.16917-2-f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Since added in commit 2bea128c3d, each SDHCI is wired with a SD
card, using empty card when no block drive provided. This is not
the desired behavior. The SDHCI exposes a SD bus to plug cards
on, if no card available, it is fine to have an unplugged bus.
Avoid creating unnecessary SD card device when no block drive
provided.
Fixes: 2bea128c3d ("hw/sd/aspeed_sdhci: New device")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200705173402.15620-1-f4bug@amsat.org
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace the free-floating set of IRQs and palmte_onoff_gpios()
function with a simple QOM device that encapsulates this
behaviour.
This fixes Coverity issue CID 1421944, which points out that
the memory returned by qemu_allocate_irqs() is leaked.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628214230.2592-3-peter.maydell@linaro.org
Remove hard-tabs from palm.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628214230.2592-2-peter.maydell@linaro.org
Currently we have a free-floating set of IRQs and a function
tosa_out_switch() which handle the GPIO lines on the tosa board which
connect to LEDs, and another free-floating IRQ and tosa_reset()
function to handle the GPIO line that resets the system. Encapsulate
this behaviour in a simple QOM device.
This commit fixes Coverity issue CID 1421929 (which pointed out that
the 'outsignals' in tosa_gpio_setup() were leaked), because it
removes the use of the qemu_allocate_irqs() API from this code
entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628203748.14250-3-peter.maydell@linaro.org
Remove the hardcoded tabs from hw/arm/tosa.c. There aren't
many, but since they're all in constant #defines they're not
going to go away with our usual "only when we touch a function"
policy on reformatting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628203748.14250-2-peter.maydell@linaro.org
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
The FROM_SSI_SLAVE() macro predates QOM and is used as a typesafe way
to cast from an SSISlave* to the instance struct of a subtype of
TYPE_SSI_SLAVE. Switch to using the QOM cast macros instead, which
have the same effect (by writing the QOM macros if the types were
previously missing them.)
(The FROM_SSI_SLAVE() macro allows the SSISlave member of the
subtype's struct to be anywhere as long as it is named "ssidev",
whereas a QOM cast macro insists that it is the first thing in the
subtype's struct. This is true for all the types we convert here.)
This removes all the uses of FROM_SSI_SLAVE() so we can delete the
definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-18-peter.maydell@linaro.org
The QOM types "spitz-lcdtg" and "corgi-ssp" are missing the
usual QOM TYPE and casting macros; provide and use them.
In particular, we can safely use the QOM cast macros instead of
FROM_SSI_SLAVE() because in both cases the 'ssidev' field of
the instance state struct is the first field in it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-17-peter.maydell@linaro.org
Instead of using printf() for logging guest accesses to invalid
register offsets in the pxa2xx PIC device, use the usual
qemu_log_mask(LOG_GUEST_ERROR,...).
This was the only user of the REG_FMT macro in pxa.h, so we can
remove that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-16-peter.maydell@linaro.org
Instead of logging guest accesses to invalid register offsets in the
Spitz flash device with zaurus_printf() (which just prints to stderr),
use the usual qemu_log_mask(LOG_GUEST_ERROR,...).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-15-peter.maydell@linaro.org
Instead of logging guest accesses to invalid register offsets in this
device using zaurus_printf() (which just prints to stderr), use the
usual qemu_log_mask(LOG_GUEST_ERROR,...).
Since this was the only use of the zaurus_printf() macro outside
spitz.c, we can move the definition of that macro from sharpsl.h
to spitz.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-14-peter.maydell@linaro.org
Currently we have a free-floating set of IRQs and a function
spitz_out_switch() which handle some miscellaneous GPIO lines for the
spitz board. Encapsulate this behaviour in a simple QOM device.
At this point we can finally remove the 'max1111' global, because the
ADC battery-temperature value is now handled by the misc-gpio device
writing the value to its outbound "adc-temp" GPIO, which the board
code wires up to the appropriate inbound GPIO line on the max1111.
This commit also fixes Coverity issue CID 1421913 (which pointed out
that the 'outsignals' in spitz_scoop_gpio_setup() were leaked),
because it removes the use of the qemu_allocate_irqs() API from this
code entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-13-peter.maydell@linaro.org
Create a header file for the hw/misc/max111x device, in the
usual modern style for QOM devices:
* definition of the TYPE_ constants and macros
* definition of the device's state struct so that it can
be embedded in other structs if desired
* documentation of the interface
This allows us to use TYPE_MAX_1111 in the spitz.c code rather
than the string "max1111".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628142429.17111-12-peter.maydell@linaro.org
The max111x ADC device model allows other code to set the level on
the 8 ADC inputs using the max111x_set_input() function. Replace
this with generic qdev GPIO inputs, which also allow inputs to be set
to arbitrary values.
Using GPIO lines will make it easier for board code to wire things
up, so that if device A wants to set the ADC input it doesn't need to
have a direct pointer to the max111x but can just set that value on
its output GPIO, which is then wired up by the board to the
appropriate max111x input.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-11-peter.maydell@linaro.org
Use the new max111x qdev properties to set the initial input
values rather than calling max111x_set_input(); this means that
on system reset the inputs will correctly return to their initial
values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628142429.17111-10-peter.maydell@linaro.org
Currently the Spitz board uses a nasty hack for the GPIO lines
that pass "bit5" and "power" information to the LCD controller:
the lcdtg realize function sets a global variable to point to
the instance it just realized, and then the functions spitz_bl_power()
and spitz_bl_bit5() use that to find the device they are changing
the internal state of. There is a comment reading:
FIXME: Implement GPIO properly and remove this hack.
which was added in 2009.
Implement GPIO properly and remove this hack.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-6-peter.maydell@linaro.org
Keep pointers to scp0, scp1 in SpitzMachineState, and just pass
that to spitz_scoop_gpio_setup().
(We'll want to use some of the other fields in SpitzMachineState
in that function in the next commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-5-peter.maydell@linaro.org
Keep pointers to the MPU and the SSI devices in SpitzMachineState.
We're going to want to make GPIO connections between some of the
SSI devices and the SCPs, so we want to keep hold of a pointer to
those; putting the MPU into the struct allows us to pass just
one thing to spitz_ssp_attach() rather than two.
We have to retain the setting of the global "max1111" variable
for the moment as it is used in spitz_adc_temp_on(); later in
this series of commits we will be able to remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-4-peter.maydell@linaro.org
For the four Spitz-family machines (akita, borzoi, spitz, terrier)
create a proper abstract class SpitzMachineClass which encapsulates
the common behaviour, rather than having them all derive directly
from TYPE_MACHINE:
* instead of each machine class setting mc->init to a wrapper
function which calls spitz_common_init() with parameters,
put that data in the SpitzMachineClass and make spitz_common_init
the SpitzMachineClass machine-init function
* move the settings of mc->block_default_type and
mc->ignore_memory_transaction_failures into the SpitzMachineClass
class init rather than repeating them in each machine's class init
(The motivation is that we're going to want to keep some state in
the SpitzMachineState so we can connect GPIOs between devices created
in one sub-function of the machine init to devices created in a
different sub-function.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200628142429.17111-3-peter.maydell@linaro.org
The spitz board has been around a long time, and still has a fair number
of hard-coded tab characters in it. We're about to do some work on
this source file, so start out by expanding out the tabs.
This commit is a pure whitespace only change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-2-peter.maydell@linaro.org
The flash device is exclusively for the host-controlled firmware, so
we should not expose it to the OS. Exposing it risks the OS messing
with it, which could break firmware runtime services and surprise the
OS when all its changes disappear after reboot.
As firmware needs the device and uses DT, we leave the device exposed
there. It's up to firmware to remove the nodes from DT before sending
it on to the OS. However, there's no need to force firmware to remove
tables from ACPI (which it doesn't know how to do anyway), so we
simply don't add the tables in the first place. But, as we've been
adding the tables for quite some time and don't want to change the
default hardware exposed to versioned machines, then we only stop
exposing the flash device tables for 5.1 and later machine types.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@arm.com>
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20200629140938.17566-4-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the virtio-iommu translates MSI transactions.
This behavior is inherited from ARM SMMU. The virt machine
code knows where the guest MSI doorbells are so we can easily
declare those regions as VIRTIO_IOMMU_RESV_MEM_T_MSI. With that
setting the guest will not map MSIs through the IOMMU and those
transactions will be simply bypassed.
Depending on which MSI controller is in use (ITS or GICV2M),
we declare either:
- the ITS interrupt translation space (ITS_base + 0x10000),
containing the GITS_TRANSLATOR or
- The GICV2M single frame, containing the MSI_SETSP_NS register.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20200629070404.10969-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add properties to the i.MX6UL processor to be able to select a
particular PHY on the MDIO bus for each FEC device.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: ea1d604198b6b73ea6521676e45bacfc597aba53.1593296112.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's auto-enable it also when maxmem is specified but no slots are
defined. This will result in us properly creating ACPI srat tables,
indicating the maximum possible PFN to the guest OS. Based on this, e.g.,
Linux will enable the swiotlb properly.
This avoids having to manually force the switolb on (swiotlb=force) in
Linux in case we're booting only using DMA memory (e.g., 2GB on x86-64),
and virtio-mem adds memory later on that really needs the swiotlb to be
used for DMA.
Let's take care of backwards compatibility if somebody has a setup that
specifies "maxram" without "slots".
Reported-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Sergio Lopez <slp@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-arm@nongnu.org <qemu-arm@nongnu.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-22-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
bcm2835_peripherals_realize(), fsl_imx25_realize() and
fsl_imx6_realize() are wrong that way: they pass &err to
object_property_set_uint() and object_property_set_bool() without
checking it, and then to sysbus_realize(). Harmless, because the
former can't actually fail here.
Fix by passing &error_abort instead.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-26-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
armsse_realize() is wrong that way: it passes &err to
object_property_set_int() multiple times without checking it, and then
to sysbus_realize(). Harmless, because the former can't actually fail
here.
Fix by passing &error_abort instead.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-25-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
aspeed_soc_ast2600_realize() and aspeed_soc_realize() are wrong that
way: they pass &err to object_property_set_int() and
object_property_set_bool() without checking it, and then to
sysbus_realize(). Harmless, because the former can't actually fail
here.
Fix by passing &error_abort instead.
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-24-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
stm32f205_soc_realize() and stm32f405_soc_realize() are wrong that
way: they pass &err to object_property_set_int() without checking it,
and then to qdev_realize(). Harmless, because the former can't
actually fail here.
Fix by passing &error_abort instead.
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630090351.1247703-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
object_property_set_link() fails when the property doesn't exist, is
not settable, or its .check() method fails. These are all programming
errors here, so passing it &error_abort is appropriate.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200630090351.1247703-17-armbru@redhat.com>
Receiving the error in a local variable only to free it is less clear
(and also less efficient) than passing NULL. Clean up.
Cc: Daniel P. Berrange <berrange@redhat.com>
Cc: Jerome Forissier <jerome@forissier.org>
CC: Greg Kurz <groug@kaod.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200630090351.1247703-4-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Deprecation period is run out and it's a time to flip the switch
introduced by cd5ff8333a. Disable legacy option for new machine
types (since 5.1) and amend documentation.
'-numa node,memdev' shall be used instead of disabled option
with new machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200609135635.761587-1-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20200626033144.790098-44-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have 2 distinct PCA9552 devices. Set their description
to distinguish them when looking at the trace events.
Description name taken from:
https://github.com/open-power/witherspoon-xml/blob/master/witherspoon.xml
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072723.6324-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedMachineState seems crippled. We use incorrectly 2
different structures to do the same thing. Merge them
altogether:
- Move AspeedMachine fields to AspeedMachineState
- AspeedMachineState is now QOM
- Remove unused AspeedMachine structure
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072132.2868-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To have a more consistent naming, rename AspeedBoardState
as AspeedMachineState.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200623072132.2868-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I'm confused by this code, 'bmc' is created as:
bmc = g_new0(AspeedBoardState, 1);
Then we use it as QOM owner for different MemoryRegion objects.
But looking at memory_region_init_ram (similarly for ROM):
void memory_region_init_ram(MemoryRegion *mr,
struct Object *owner,
const char *name,
uint64_t size,
Error **errp)
{
DeviceState *owner_dev;
Error *err = NULL;
memory_region_init_ram_nomigrate(mr, owner, name, size, &err);
if (err) {
error_propagate(errp, err);
return;
}
/* This will assert if owner is neither NULL nor a DeviceState.
* We only want the owner here for the purposes of defining a
* unique name for migration. TODO: Ideally we should implement
* a naming scheme for Objects which are not DeviceStates, in
* which case we can relax this restriction.
*/
owner_dev = DEVICE(owner);
vmstate_register_ram(mr, owner_dev);
}
The expected assertion is not triggered ('bmc' is not NULL neither
a DeviceState).
'bmc' structure is defined as:
struct AspeedBoardState {
AspeedSoCState soc;
MemoryRegion ram_container;
MemoryRegion max_ram;
};
What happens is when using 'OBJECT(bmc)', the QOM macros cast the
memory pointed by bmc, which first member is 'soc', which is
initialized ...:
object_initialize_child(OBJECT(machine), "soc",
&bmc->soc, amc->soc_name);
The 'soc' object is indeed a DeviceState, so the assertion passes.
Since this is fragile and only happens to work by luck, remove the
dangerous OBJECT(bmc) owner argument.
Note, this probably breaks migration for this machine.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200623072132.2868-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In case it is dynamically instantiated, add the TPM 2.0 device object
under the DSDT table in the ACPI namespace. Its HID is MSFT0101
while its current resource settings (CRS) property is initialized
with the guest physical address and MMIO size of the device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200622140620.17229-3-eric.auger@redhat.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We always pass &error_abort. Drop the parameter, use &error_abort
directly.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-15-armbru@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
This adds support for memory(pc-dimm) hot remove on arm/virt that
uses acpi ged device.
NVDIMM hot removal is not yet supported.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-id: 20200622124157.20360-1-shameerali.kolothum.thodi@huawei.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From 'Application Note AN521', chapter 4.7:
The SMM implements four SBCon serial modules:
One SBCon module for use by the Color LCD touch interface.
One SBCon module to configure the audio controller.
Two general purpose SBCon modules, that connect to the
Expansion headers J7 and J8, are intended for use with the
V2C-Shield1 which provide an I2C interface on the headers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-15-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-14-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From 'Application Note AN385', chapter 3.14:
The SMM implements a simple SBCon interface based on I2C.
There are 4 SBCon interfaces on the FPGA APB subsystem.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-13-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From 'Application Note AN385', chapter 3.9, SPI:
The SMM implements five PL022 SPI modules.
Two pairs of modules share the same OR-gated IRQ.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-12-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-11-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already model the CMSDK APB watchdog device, let's use it!
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-9-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To differenciate with the CMSDK APB peripheral region,
rename this region 'CMSDK AHB peripheral region'.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By using the TYPE_* definitions for devices, we can:
- quickly find where devices are used with 'git-grep'
- easily rename a device (one-line change).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set vendor property to IMX to enable IMX specific functionality
in sdhci code.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200603145258.195920-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-53-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is still the same transformation as in the previous commits, but
here the sysbus_init_child_obj() and its matching realize in are in
separate files. Fortunately, there's just one realize left to
convert.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-51-armbru@redhat.com>
These are init/realize pairs produced by the previous commit's
Coccinelle script where the argument test doesn't quite match. They
need even more careful review.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-50-armbru@redhat.com>
This is the same transformation as in the previous commit, except
sysbus_init_child_obj() and realize are too separated for the commit's
Coccinelle script to handle, typically because sysbus_init_child_obj()
is in a device's instance_init() method, and the matching realize is
in its realize() method.
Perhaps a Coccinelle wizard could make it transform that pattern, but
I'm just a bungler, and the best I can do is transforming the two
separate parts separately:
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(OBJECT(child), true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(child, true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
@@
- qdev_init_nofail(DEVICE(child));
+ sysbus_realize(SYS_BUS_DEVICE(child), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
expression dev;
@@
dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
identifier dev;
@@
DeviceState *dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression parent, name, size, type;
expression child;
symbol true;
@@
- sysbus_init_child_obj(parent, name, child, size, type);
+ sysbus_init_child_XXX(parent, name, child, size, type);
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, child, sizeof(*child), type)
+ object_initialize_child(parent, propname, child, type)
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, &child, sizeof(child), type)
+ object_initialize_child(parent, propname, &child, type)
This script is *unsound*: we need to manually verify init and realize
conversions are properly paired.
This commit has only the pairs where object_initialize_child()'s
@child and sysbus_realize()'s @dev argument text match exactly within
the same source file.
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-49-armbru@redhat.com>
The callers of sysbus_init_child_obj() commonly pass either &child,
sizeof(child), or pchild, sizeof(*pchild). Tidy up the few that use
something else instead, mostly to keep future commits simpler.
Coccinelle script:
@@
expression parent, propname, type;
expression child;
type T;
T proxy;
@@
(
sysbus_init_child_obj(parent, propname, &child, sizeof(child), type)
|
sysbus_init_child_obj(parent, propname, child, sizeof(*child), type)
|
- sysbus_init_child_obj(parent, propname, child, sizeof(proxy), type)
+ sysbus_init_child_obj(parent, propname, child, sizeof(*child), type)
)
This script is *unsound*: for each change we need to verify the
@childsize argument stays the same. I did.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-44-armbru@redhat.com>
armsse_init() initializes s->armv7m[i] for all i. It passes the size
of the entire array instead of the array element to
sysbus_init_child_obj(). Harmless, but fix it anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-43-armbru@redhat.com>
The callers of sysbus_init_child_obj() commonly pass either &child,
sizeof(child), or pchild, sizeof(*pchild). Tidy up two that don't,
mostly to keep future commits simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-41-armbru@redhat.com>
OBJECT(child) expands to ((Object *)(child)). sysbus_init_child_obj()
parameter @child is void *. Pass child instead of OBJECT(child).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-40-armbru@redhat.com>
The callers of object_initialize_child() commonly pass either
&child, sizeof(child), or pchild, sizeof(*pchild). Tidy up the few
that don't, mostly to keep the next commit simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-36-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is somewhere between
not worthwhile and infeasible (at least for me).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-11-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
These devices are optional, and enabled by property "enable-bitband".
armv7m_instance_init() creates them unconditionally, because the
property has not been set then. armv7m_realize() realizes them only
when the property is true. Works, although it leaves unrealized
devices hanging around in the QOM composition tree. Affects machines
microbit, mps2-an505, mps2-an521, musca-a, and musca-b1.
Delete the unused devices by making armv7m_realize() unparent them.
Visible in "info qom-tree"; here's the change for microbit:
/machine (microbit-machine)
/microbit.twi (microbit.i2c)
/microbit.twi[0] (qemu:memory-region)
/nrf51 (nrf51-soc)
/armv6m (armv7m)
/armv7m-container[0] (qemu:memory-region)
- /bitband[0] (ARM,bitband-memory)
- /bitband[0] (qemu:memory-region)
- /bitband[1] (ARM,bitband-memory)
- /bitband[0] (qemu:memory-region)
/cpu (cortex-m0-arm-cpu)
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200609122339.937862-7-armbru@redhat.com>
The number of MACs supported by an Aspeed SoC is defined by "macs_num"
under the SoC model, that is two for the AST2400 and AST2500 and four
for the AST2600. The model initializes the maximum number of supported
MACs but the number of realized devices is capped by the number of
network device back-ends defined on the command line. This can leave
unrealized devices hanging around in the QOM composition tree.
To get virtual hardware that matches the physical hardware, you have
to pass exactly as many -nic options as there are MACs, and some of
them must be -nic none:
* Machines ast2500-evb, palmetto-bmc, romulus-bmc, sonorapass-bmc,
swift-bmc, and witherspoon-bmc: two -nic, and the second one must be
-nic none.
* Machine ast2600-evb: four -nic, the first one must be -nic none.
* Machine tacoma-bmc: four nic, the first two and the last one must be
-nic none.
Modify the machine initialization to define which MACs are attached to
a network device back-end using a bit-field property "macs-mask" and
let the SoC realize all network devices.
The default setting of "macs-mask" is "use MAC0" only, which works for
all our AST2400 and AST2500 machines. The AST2600 machines have
different configurations. The AST2600 EVB machine activates MAC1, MAC2
and MAC3 and the Tacoma BMC machine activates MAC2.
Incompatible CLI change: -nic options now apply to *active* MACs:
MAC1, MAC2, MAC3 for ast2600-evb, MAC2 for tacoma-bmc, and MAC0 for
all the others.
The machines now always get all MACs as they should. Visible in "info
qom-tree", here's the change for tacoma-bmc:
/machine (tacoma-bmc-machine)
/peripheral (container)
/peripheral-anon (container)
/soc (ast2600-a1)
[...]
/ftgmac100[0] (ftgmac100)
/ftgmac100[0] (qemu:memory-region)
/ftgmac100[1] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
/ftgmac100[2] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
/ftgmac100[3] (ftgmac100)
+ /ftgmac100[0] (qemu:memory-region)
[...]
/mii[0] (aspeed-mmi)
/aspeed-mmi[0] (qemu:memory-region)
/mii[1] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
/mii[2] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
/mii[3] (aspeed-mmi)
+ /aspeed-mmi[0] (qemu:memory-region)
Also visible in "info qtree"; here's the change for tacoma-bmc:
dev: ftgmac100, id ""
gpio-out "sysbus-irq" 1
aspeed = true
- mac = "52:54:00:12:34:56"
- netdev = "hub0port0"
+ mac = "52:54:00:12:34:57"
+ netdev = ""
mmio 000000001e660000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:58"
netdev = ""
+ mmio 000000001e680000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
- netdev = ""
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:56"
+ netdev = "hub0port0"
+ mmio 000000001e670000/0000000000002000
dev: ftgmac100, id ""
- aspeed = false
- mac = "00:00:00:00:00:00"
+ gpio-out "sysbus-irq" 1
+ aspeed = true
+ mac = "52:54:00:12:34:59"
netdev = ""
+ mmio 000000001e690000/0000000000002000
[...]
dev: aspeed-mmi, id ""
mmio 000000001e650000/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650008/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650010/0000000000000008
dev: aspeed-mmi, id ""
+ mmio 000000001e650018/0000000000000008
Inactive MACs will have no peer and QEMU may warn the user with :
qemu-system-arm: warning: nic ftgmac100.0 has no peer
qemu-system-arm: warning: nic ftgmac100.1 has no peer
qemu-system-arm: warning: nic ftgmac100.3 has no peer
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[Commit message expanded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-6-armbru@redhat.com>
Commit ece09beec4 ("aspeed: introduce a configurable number of CPU
per machine") was a convient change during bringup but the Aspeed SoCs
have a fixed number of CPUs : one for the AST2400 and AST2500, and two
for the AST2600.
When the number of CPUs configured with -smp is less than the SoC's
fixed number, the "unconfigured" CPUs are left unrealized. This can
happen for machines ast2600-evb and tacoma-bmc, where the SoC's fixed
number is 2. To get virtual hardware that matches the physical
hardware, you have to pass -smp cpus=2 (or its sugared form -smp 2).
We normally reject -smp cpus=N when N exceeds the machine's limit.
Except we ignore cpus=2 (and only cpus=2) with a warning for machines
ast2500-evb, palmetto-bmc, romulus-bmc, sonorapass-bmc, swift-bmc, and
witherspoon-bmc.
Remove the "num-cpu" property from the SoC state and use the fixed
number of CPUs defined in the SoC class instead. Compute the default,
min, max number of CPUs of the machine directly from the SoC class
definition.
Machines ast2600-evb and tacoma-bmc now always get their second CPU as
they should. Visible in "info qom-tree"; here's the change for
ast2600-evb:
/machine (ast2600-evb-machine)
/peripheral (container)
/peripheral-anon (container)
/soc (ast2600-a1)
/a7mpcore (a15mpcore_priv)
/a15mp-priv-container[0] (qemu:memory-region)
/gic (arm_gic)
/gic_cpu[0] (qemu:memory-region)
/gic_cpu[1] (qemu:memory-region)
+ /gic_cpu[2] (qemu:memory-region)
/gic_dist[0] (qemu:memory-region)
/gic_vcpu[0] (qemu:memory-region)
/gic_viface[0] (qemu:memory-region)
/gic_viface[1] (qemu:memory-region)
+ /gic_viface[2] (qemu:memory-region)
/unnamed-gpio-in[0] (irq)
[...]
+ /unnamed-gpio-in[160] (irq)
[same for 161 to 190...]
+ /unnamed-gpio-in[191] (irq)
Also visible in "info qtree"; here's the change for ast2600-evb:
bus: main-system-bus
type System
dev: a15mpcore_priv, id ""
gpio-in "" 128
- gpio-out "sysbus-irq" 5
- num-cpu = 1 (0x1)
+ gpio-out "sysbus-irq" 10
+ num-cpu = 2 (0x2)
num-irq = 160 (0xa0)
mmio 0000000040460000/0000000000008000
dev: arm_gic, id ""
- gpio-in "" 160
- num-cpu = 1 (0x1)
+ gpio-in "" 192
+ num-cpu = 2 (0x2)
num-irq = 160 (0xa0)
revision = 2 (0x2)
has-security-extensions = true
has-virtualization-extensions = true
num-priority-bits = 8 (0x8)
mmio ffffffffffffffff/0000000000001000
mmio ffffffffffffffff/0000000000002000
mmio ffffffffffffffff/0000000000001000
mmio ffffffffffffffff/0000000000002000
mmio ffffffffffffffff/0000000000000100
+ mmio ffffffffffffffff/0000000000000100
+ mmio ffffffffffffffff/0000000000000200
mmio ffffffffffffffff/0000000000000200
The other machines now reject -smp cpus=2 just like -smp cpus=3 and up.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Commit message expanded]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-5-armbru@redhat.com>
stm32f405_soc_initfn() creates six such devices, but
stm32f405_soc_realize() realizes only one. Affects machine
netduinoplus2.
In theory, a device becomes real only on realize. In practice, the
transition from unreal to real is a fuzzy one. The work to make a
device real can be spread between realize methods (fine),
instance_init methods (wrong), and board code wiring up the device
(fine as long as it effectively happens on realize). Depending on
what exactly is done where, a device can work even when we neglect
to realize it.
The five unrealized devices appear to stay unreal: neither MMIO nor
IRQ get wired up.
Fix stm32f405_soc_realize() to realize and wire up all six. Visible
in "info qtree":
bus: main-system-bus
type System
dev: stm32f405-soc, id ""
cpu-type = "cortex-m4-arm-cpu"
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio ffffffffffffffff/00000000000000ff
+ mmio 0000000040012000/00000000000000ff
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio ffffffffffffffff/00000000000000ff
+ mmio 0000000040012100/00000000000000ff
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio ffffffffffffffff/00000000000000ff
+ mmio 0000000040012200/00000000000000ff
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio ffffffffffffffff/00000000000000ff
+ mmio 0000000040012300/00000000000000ff
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio 0000000040012000/00000000000000ff
+ mmio 0000000040012400/00000000000000ff
dev: stm32f2xx-adc, id ""
gpio-out "sysbus-irq" 1
- mmio ffffffffffffffff/00000000000000ff
+ mmio 0000000040012500/00000000000000ff
dev: armv7m, id ""
Fixes: 529fc5fd3e
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200609122339.937862-2-armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Max slots negotiation for vhost-user.
Free page reporting for balloon.
Partial TPM2 ACPI support for ARM.
Support for NVDIMMs having their own proximity domains.
New vhost-user-vsock device.
Fixes, cleanups in ACPI, PCI, virtio.
New tests for TPM ACPI.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl7jjpwPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp9AEH/RH+o9fT+Jvwv1yiCF44kjrfQ9MHzT+hDo96
vd6Ynj6O49M+ObL3f9fI5ICYHAmZQFzouJ671/FcQQF/CrMot1HBnHAWAzS2YoFu
3iNOA6PmWn0fWoVAuIfmhtE0PKNJdsuyyJMbcKY5d5bSPugO3b/bIPvo8oVAIXiM
3xf0KbicB6m0z24ssZoI7KP7PSJcacDViFXUJkgCIMce68od4CDEQ8TGi6jBmAzQ
VdriGnOCJ9Wo60GC4KL4v8HKZWnq4Nz4qfwQtHdY/MUL30eFDjYcgF0AMYLHrymy
DInh/GRQMxtD0VvOxtq1BUV0tHk/qH4XyEohSyBOrIrH+ifnjds=
=hh+M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,acpi,pci: features, fixes, cleanups, tests
Max slots negotiation for vhost-user.
Free page reporting for balloon.
Partial TPM2 ACPI support for ARM.
Support for NVDIMMs having their own proximity domains.
New vhost-user-vsock device.
Fixes, cleanups in ACPI, PCI, virtio.
New tests for TPM ACPI.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 12 Jun 2020 15:18:04 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (58 commits)
virtio-pci: fix queue_enable write
pci: Display PCI IRQ pin in "info pci"
Fix parameter type in vhost migration log path
acpi: ged: rename event memory region
acpi: fadt: add hw-reduced sleep register support
acpi: madt: skip pci override on pci-less systems.
acpi: create acpi-common.c and move madt code
acpi: make build_madt() more generic.
virtio: add vhost-user-vsock-pci device
virtio: add vhost-user-vsock base device
vhost-vsock: add vhost-vsock-common abstraction
hw/pci: Fix crash when running QEMU with "-nic model=rocker"
libvhost-user: advertise vring features
Lift max ram slots limit in libvhost-user
Support individual region unmap in libvhost-user
Support adding individual regions in libvhost-user
Support ram slot configuration in libvhost-user
Refactor out libvhost-user fault generation logic
Lift max memory slots limit imposed by vhost-user
Transmit vhost-user memory regions individually
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>