Implement the MVE DLSTP insn; this is like the existing DLS
insn, except that it must do an FPU access check and it
sets LTPSIZE to the value specified in the insn.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-9-peter.maydell@linaro.org
Implement the MVE WLSTP insn; this is like the existing WLS insn,
except that it specifies a size value which is used to set
FPSCR.LTPSIZE.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-8-peter.maydell@linaro.org
Implement the MVE LCTP instruction.
We put its decode and implementation with the other
low-overhead-branch insns because although it is only present if MVE
is implemented it is logically in the same group as the other LOB
insns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-7-peter.maydell@linaro.org
In commit a3494d4671 we reworked the M-profile handling of its
checks for when the NOCP exception should be raised because the FPU
is disabled, so that (in line with the architecture) the NOCP check
is done early over a large range of the encoding space, and takes
precedence over UNDEF exceptions. As part of this, we removed the
code from full_vfp_access_check() which raised an exception there for
M-profile with the FPU disabled, because it was no longer reachable.
For MVE, some instructions which are outside the "coprocessor space"
region of the encoding space must nonetheless do "is the FPU enabled"
checks and possibly raise a NOCP exception. (In particular this
covers the MVE-specific low-overhead branch insns LCTP, DLSTP and
WLSTP.) To support these insns, reinstate the code in
full_vfp_access_check(), so that their trans functions can call
vfp_access_check() and get the correct behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-6-peter.maydell@linaro.org
On A-profile, PSR bits [15:10][26:25] are always the IT state bits.
On M-profile, some of the reserved encodings of the IT state are used
to instead indicate partial progress through instructions that were
interrupted partway through by an exception and can be resumed.
These resumable instructions fall into two categories:
(1) load/store multiple instructions, where these bits are called
"ICI" and specify the register in the ldm/stm list where execution
should resume. (Specifically: LDM, STM, VLDM, VSTM, VLLDM, VLSTM,
CLRM, VSCCLRM.)
(2) MVE instructions subject to beatwise execution, where these bits
are called "ECI" and specify which beats in this and possibly also
the following MVE insn have been executed.
There are also a few insns (LE, LETP, and BKPT) which do not use the
ICI/ECI bits but must leave them alone.
Otherwise, we should raise an INVSTATE UsageFault for any attempt to
execute an insn with non-zero ICI/ECI bits.
So far we have been able to ignore ECI/ICI, because the architecture
allows the IMPDEF choice of "always restart load/store multiple from
the beginning regardless of ICI state", so the only thing we have
been missing is that we don't raise the INVSTATE fault for bad guest
code. However, MVE requires that we honour ECI bits and do not
rexecute beats of an insn that have already been executed.
Add the support in the decoder for handling ECI/ICI:
* identify the ECI/ICI case in the CONDEXEC TB flags
* when a load/store multiple insn succeeds, it updates the ECI/ICI
state (both in DisasContext and in the CPU state), and sets a flag
to say that the ECI/ICI state was handled
* if we find that the insn we just decoded did not handle the
ECI/ICI state, we delete all the code that we just generated for
it and instead emit the code to raise the INVFAULT. This allows
us to avoid having to update every non-MVE non-LDM/STM insn to
make it check for "is ECI/ICI set?".
We continue with our existing IMPDEF choice of not caring about the
ICI state for the load/store multiples and simply restarting them
from the beginning. Because we don't allow interrupts in the middle
of an insn, the only way we would see this state is if the guest set
ICI manually on return from an exception handler, so it's a corner
case which doesn't merit optimisation.
ICI update for LDM/STM is simple -- it always zeroes the state. ECI
update for MVE beatwise insns will be a little more complex, since
the ECI state may include information for the following insn.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-5-peter.maydell@linaro.org
When MVE is supported, the VPR register has a place on the exception
stack frame in a previously reserved slot just above the FPSCR.
It must also be zeroed in various situations when we invalidate
FPU context.
Update the code which handles the stack frames (exception entry and
exit code, VLLDM, and VLSTM) to save/restore VPR.
Update code which invalidates FP registers (mostly also exception
entry and exit code, but also VSCCLRM and the code in
full_vfp_access_check() that corresponds to the ExecuteFPCheck()
pseudocode) to zero VPR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-4-peter.maydell@linaro.org
MVE has an FPSCR.QC bit similar to the A-profile Neon one; when MVE
is implemented make the bit writeable, both in the generic "load and
store FPSCR" helper functions and in the code for handling the NZCVQC
sysreg which we had previously left as "TODO when we implement MVE".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-3-peter.maydell@linaro.org
Currently we provide Hn and H1_n macros for accessing the correct
data within arrays of vector elements of size 1, 2 and 4, accounting
for host endianness. We don't provide any macros for elements of
size 8 because there the host endianness doesn't matter. However,
this does result in awkwardness where we need to pass empty arguments
to macros, because checkpatch complains about them. The empty
argument is a little confusing for humans to read as well.
Add H8() and H1_8() macros and use them where we were previously
passing empty arguments to macros.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614151007.4545-2-peter.maydell@linaro.org
Message-id: 20210610132505.5827-1-peter.maydell@linaro.org
Adds the pca954x muxes expected.
Tested: Booted quanta-q71l image to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20210608202522.2677850-4-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds comments to the board init to identify missing i2c devices.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20210608202522.2677850-2-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The test was off-by-one, because tag_last points to the
last byte of the tag to check, thus tag_last - prev_page
will equal TARGET_PAGE_SIZE when we use the first byte
of the next page.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/403
Reported-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210612195707.840217-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit da6d674e50 we split the NVIC code out from the GIC.
This allowed us to specify the NVIC's default value for the num-irq
property (64) in the usual way in its property list, and we deleted
the previous hack where we updated the value in the state struct in
the instance init function. Remove a stale comment about that hack
which we forgot to delete at that time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614161243.14211-1-peter.maydell@linaro.org
Add a comment and i2c method that describes the board layout.
Tested: firmware booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Brandon Kim <brandonkim@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210608193605.2611114-3-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fprintf+assert has been in place since the beginning.
It is after to the fp_access_check, so we need to move the
check up. Fold that in to the pairwise filter.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210604183506.916654-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The default of this switch is truly unreachable.
The switch selector is 3 bits, and all 8 cases are present.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210604183506.916654-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fprintf+assert has been in place since the beginning.
It is prior to the fp_access_check, so we're still good to
raise sigill here.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/381
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210604183506.916654-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 382c7160d1 ("hw/intc/arm_gicv3_cpuif: Fix EOIR write access
check logic") added an assert_not_reached() if the guest writes the EOIR
register while no interrupt is active.
It turns out some software does this: EDK2, in
GicV3ExitBootServicesEvent(), unconditionally write EOIR for all
interrupts that it manages. This now causes QEMU to abort when running
UEFI on a VM with GICv3. Although it is UNPREDICTABLE behavior and EDK2
does need fixing, the punishment seems a little harsh, especially since
icc_eoir_write() already tolerates writes of nonexistent interrupt
numbers. Display a guest error and tolerate spurious EOIR writes.
Fixes: 382c7160d1 ("hw/intc/arm_gicv3_cpuif: Fix EOIR write access check logic")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210604130352.1887560-1-jean-philippe@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=APsS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/berrange-gitlab/tags/misc-fixes-pull-request' into staging
Merge misc patches
# gpg: Signature made Mon 14 Jun 2021 15:14:48 BST
# gpg: using RSA key DAF3A6FDB26B62912D0E8E3FBE86EBB415104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>" [full]
# gpg: aka "Daniel P. Berrange <berrange@redhat.com>" [full]
# Primary key fingerprint: DAF3 A6FD B26B 6291 2D0E 8E3F BE86 EBB4 1510 4FDF
* remotes/berrange-gitlab/tags/misc-fixes-pull-request:
usb/dev-mtp: use GDateTime for formatting timestamp for objects
block: use GDateTime for formatting timestamp when dumping snapshot info
migration: use GDateTime for formatting timestamp in snapshot names
block: remove duplicate trace.h include
block: add trace point when fdatasync fails
block: preserve errno from fdatasync failures
softmmu: add trace point when bdrv_flush_all fails
migration: add trace point when vm_stop_force_state fails
sasl: remove comment about obsolete kerberos versions
docs: recommend SCRAM-SHA-256 SASL mech instead of SHA-1 variant
docs: document usage of the authorization framework
docs: document how to pass secret data to QEMU
docs: add table of contents to QAPI references
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GDateTime APIs provided by GLib avoid portability pitfalls, such
as some platforms where 'struct timeval.tv_sec' field is still 'long'
instead of 'time_t'. When combined with automatic cleanup, GDateTime
often results in simpler code too.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The GDateTime APIs provided by GLib avoid portability pitfalls, such
as some platforms where 'struct timeval.tv_sec' field is still 'long'
instead of 'time_t'. When combined with automatic cleanup, GDateTime
often results in simpler code too.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The GDateTime APIs provided by GLib avoid portability pitfalls, such
as some platforms where 'struct timeval.tv_sec' field is still 'long'
instead of 'time_t'. When combined with automatic cleanup, GDateTime
often results in simpler code too.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
A flush failure is a critical failure scenario for some operations.
For example, it will prevent migration from completing, as it will
make vm_stop() report an error. Thus it is important to have a
trace point present for debugging.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
When fdatasync() fails on a file backend we set a flag that
short-circuits any future attempts to call fdatasync(). The
first failure returns the true errno, but the later short-
circuited calls return a generic EIO. The latter is unhelpful
because fdatasync() can return a variety of errnos, including
EACCESS.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The VM stop process has to flush outstanding I/O and this is a critical
failure scenario that is hard to diagnose. Add a probe point that
records the flush return code.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
This is a critical failure scenario for migration that is hard to
diagnose from existing probes. Most likely it is caused by an error
from bdrv_flush(), but we're not logging the errno anywhere, hence
this new probe.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
This is not relevant to any OS distro that QEMU currently targets.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The SHA-256 variant better meats modern security expectations.
Also warn that the password file is storing entries in clear
text.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The authorization framework provides a way to control access to network
services after a client has been authenticated. This documents how to
actually use it.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The QAPI reference docs for the guest agent, storage daemon and QMP are
all rather long and hard to navigate unless you already know the name of
the command and can do full text search for it.
A table of contents in each doc will help people locate stuff much more
easily.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Message-Id: <20210601125143.191165-1-luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Typo in the conversion to FloatParts64.
Fixes: 572c4d862f
Fixes: Coverity CID 1457457
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210607223812.110596-1-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit 5e8892db93 fixed several function signatures but tcg_out_op for
arm is missing. This patch fixes it as well.
Signed-off-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210610224450.23425-1-jziviani@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
At some point during the development of tcg_constant_*, I changed
my mind about whether such temps should be able to be passed to
tcg_temp_free_*. The final version committed allows this, but the
commentary was not updated to match.
Fixes: c0522136ad
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Introduce a function to remove everything emitted
since a given point.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These variables belong to the jit side, not the user side.
Since tcg_init_ctx is no longer used outside of tcg/, move
the declaration to tcg-internal.h.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There's a change in mprotect() behaviour [1] in the latest macOS
on M1 and it's not yet clear if it's going to be fixed by Apple.
In this case, instead of changing permissions of N guard pages,
we change permissions of N rwx regions. The same number of
syscalls are required either way.
[1] https://gist.github.com/hikalium/75ae822466ee4da13cbbe486498a191f
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Do not handle protections on a case-by-case basis in the
various alloc_code_gen_buffer instances; do it within a
single loop in tcg_region_init.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
If qemu_get_host_physmem returns an odd number of pages,
then physmem / 8 will not be a multiple of the page size.
The following was observed on a gitlab runner:
ERROR qtest-arm/boot-serial-test - Bail out!
ERROR:../util/osdep.c:80:qemu_mprotect__osdep: \
assertion failed: (!(size & ~qemu_real_host_page_mask))
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For --enable-tcg-interpreter on Windows, we will need this.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move the call out of the N versions of alloc_code_gen_buffer
and into tcg_region_init.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Change the interface from a boolean error indication to a
negative error vs a non-negative protection. For the moment
this is only interface change, not making use of the new data.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Do not mess around with setting values within tcg_init_ctx.
Put the values into 'region' directly, which is where they
will live for the lifetime of the program.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Shortly, the full code_gen_buffer will only be visible
to region.c, so move in_code_gen_buffer out-of-line.
Move the debugging versions of tcg_splitwx_to_{rx,rw}
to region.c as well, so that the compiler gets to see
the implementation of in_code_gen_buffer.
This leaves exactly one use of in_code_gen_buffer outside
of region.c, in cpu_restore_state. Which, being on the
exception path, is not performance critical.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Return output buffer and size via output pointer arguments,
rather than returning size via tcg_ctx->code_gen_buffer_size.
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
