In ARMv8 the 32 bit coprocessor ID register space is tidied up to
remove the wildcarded aliases of the MIDR and the RAZ behaviour
for the unassigned space where crm = 3..7. Make sure we don't
expose thes wildcards for v8 cores. This means we need to have
a specific implementation for REVIDR, an IMPDEF register which
may be the same as the MIDR (and which we always implement as such).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the ISR_EL1 register. This is actually present in
ARMv7 as well but was previously unimplemented. It is a
read-only register that indicates whether interrupts are
currently pending.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the ACTLR (auxiliary control
register). Note that QEMU internally tends to call this
AUXCR for historical reasons.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement AArch64 view of the CONTEXTIDR register.
We tighten up the condition when we flush the TLB on a CONTEXTIDR
write to avoid needlessly flushing the TLB every time on a 64
bit system (and also on a 32 bit system using LPAE, as a bonus).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
All the AArch32 ID registers are visible from AArch64
(in addition to the AArch64-specific ID_AA64* registers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For ARMv8 there are two changes to the MVFR media feature registers:
* there is a new MVFR2 which is accessible from 32 bit code
* 64 bit code accesses these via the usual sysreg instructions
rather than with a floating-point specific instruction
Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Move arm_log_exception() into internals.h so we can use it from
helper-a64.c for the AArch64 exception entry code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 SPSR_EL1. For compatibility with how KVM
handles SPSRs and with the architectural mapping between AArch32
and AArch64, we put this in the banked_spsr[] array in the slot
that is used for SVC in AArch32. This means we need to extend the
array from uint32_t to uint64_t, which requires some reworking
of the 32 bit KVM save/restore code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement handling for the AArch64 SP_EL0 system register.
This holds the EL0 stack pointer, and is only accessible when
it's not being used as the stack pointer, ie when we're in EL1
and EL1 is using its own stack pointer. We also provide a
definition of the SP_EL1 register; this isn't guest visible
as a system register for an implementation like QEMU which
doesn't provide EL2 or EL3; however it is useful for ensuring
the underlying state is migrated.
We need to update the state fields in the CPU state whenever
we switch stack pointers; this happens when we take an exception
and also when SPSEL is used to change the bit in PSTATE which
indicates which stack pointer EL1 should use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Add the AArch64 ELR_EL1 register.
Note that this does not live in env->cp15: for KVM migration
compatibility we need to migrate it separately rather than
as part of the system registers, because the KVM-to-userspace
interface puts it in the struct kvm_regs rather than making
them visible via the ONE_REG ioctls.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement AArch64 views of ESR_EL1 and FAR_EL1, and make the 32 bit
DFSR, DFAR, IFAR share state with them as architecturally specified.
The IFSR doesn't share state with any AArch64 register visible at EL1,
so just rename the state field without widening it to 64 bits.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: Minor tweaks; fix some bugs involving inconsistencies between
use of offsetof() or offsetoflow32() and struct field width]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The ARM946 model currently uses the c5_data and c5_insn fields in the CPU
state struct to store the contents of its access permission registers.
This is confusing and a good source of bugs because for all the MMU-based
CPUs those fields are fault status and fault address registers, which
behave completely differently; they just happen to use the same cpreg
encoding. Split them out to use their own fields instead.
These registers are only present in PMSAv5 MPU systems (of which the
ARM946 is our only current example); PMSAv6 and PMSAv7 (which we have
no implementations of) handle access permissions differently. We name
the new state fields accordingly.
Note that this change fixes a bug where a data abort or prefetch abort
on the ARM946 would accidentally corrupt the access permission registers
because the interrupt handling code assumed the c5_data and c5_insn
fields were always fault status registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the DC ZVA instruction, which clears a block of memory.
The fast path obtains a pointer to the underlying RAM via the TCG TLB
data structure so we can do a direct memset(), with fallback to a
simple byte-store loop in the slow path.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Suppress the ID_AA64DFR0_EL1 PMUVer field, even if the CPU specific
value claims that it exists. QEMU doesn't currently implement it,
and not advertising it prevents the guest from trying to use it
and getting UNDEFs on unimplemented registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
---
This is arguably a hack, but otherwise Linux tries to prod
half a dozen PMU sysregs.
Add support for v8 page table walks. This supports stage 1 translations
for 4KB, 16KB and 64KB page sizes starting with 0 or 1 level.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: fix style nits, fold in 16/64K page support patch, use
arm_el_is_aa64() to decide whether to do 64 bit page table walk]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Set up the required syndrome information when we detect an MMU fault.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: split out from exception handling patch, tweaked to bring
in line with how we create other kinds of syndrome information]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For AArch32 exceptions, the only information provided about
the cause of an exception is the individual exception type (data
abort, undef, etc), which we store in cs->exception_index. For
AArch64, the CPU provides much more detail about the cause of
the exception, which can be found in the syndrome register.
Create a set of fields in CPUARMState which must be filled in
whenever an exception is raised, so that exception entry can
correctly fill in the syndrome register for the guest.
This includes the information which in AArch32 appears in
the DFAR and IFAR (fault address registers) and the DFSR
and IFSR (fault status registers) for data aborts and
prefetch aborts, since if we end up taking the MMU fault
to AArch64 rather than AArch32 this will need to end up
in different system registers.
This patch does a refactoring which moves the setting of the
AArch32 DFAR/DFSR/IFAR/IFSR from the point where the exception
is raised to the point where it is taken. (This is no change
for cores with an MMU, retains the existing clearly incorrect
behaviour for ARM946 of trashing the MP access permissions
registers which share the c5_data and c5_insn state fields,
and has no effect for v7M because we don't implement its
MPU fault status or address registers.)
As a side effect of the cleanup we fix a bug in the AArch64
linux-user mode code where we were passing a 64 bit fault
address through the 32 bit c6_data/c6_insn fields: it now
goes via the always-64-bit exception.vaddress.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the DAIF system register which is a view of the
DAIF bits in PSTATE. To avoid needing a readfn, we widen
the daif field in CPUARMState to uint64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Currently cpu.h defines a mixture of functions and types needed by
the rest of QEMU and those needed only by files within target-arm/.
Split the latter out into a new header so they aren't needlessly
exposed further than required.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
This adds support for [UF]RSQRTE instructions. It utilises the existing
NEON helpers with some changes. The changes include an explicit passing
of fpstatus (so the correct one is used between arm32 and aarch64),
denormilzation, more correct error handling and also proper scaling of
the fraction going into the estimate.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-25-git-send-email-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement URECPE and FRECPE instructions in both scalar and vector forms.
The actual reciprocal estimate function is shared with the A32/T32 Neon
code. However in A64 we aren't using the Neon "standard FPSCR value"
so extra checks are necessary to handle non-squashed denormal inputs
which can never happen for A32/T32. Calling conventions for the helpers
are thus modified to pass the fpst directly; we mark the helpers as
TCG_CALL_NO_RWG since we're changing the declarations anyway.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-21-git-send-email-peter.maydell@linaro.org
Now that the PMCR writefn makes timer accesses, its reginfo needs
the ARM_CP_IO flag, so that icount mode works correctly. (Fixes
the bug accidentally introduced in commit 7c2cb42b).
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1394908291-16546-1-git-send-email-peter.maydell@linaro.org
Codespell found and fixed these new typos:
* doesnt -> doesn't
* funtion -> function
* perfomance -> performance
* remaing -> remaining
A coding style issue (line too long) was fixed manually.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
All targets using it gain the ability to set -cpu name,key=value,...
options via the default TYPE_CPU CPUClass::parse_features() implementation.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commits ab1da85791,
fdfba1a298,
2c17449b30 added usages of ENV_GET_CPU()
macro to target-specific code.
Use arm_env_get_cpu() instead and enforce separating variable
declarations.
Cc: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commit 4cc35614a moved the exception mask bits out of env->uncached_cpsr
and into env->daif. However the env->daif contents are AArch64 style
mask bits, which include not just the AArch32 AIF bits but also the
new D bit (masks debug exceptions). This means that when reconstructing
the AArch32 CPSR value we must not allow the D bit in env->daif to get
into the CPSR, because the corresponding bit in the CPSR is E, the
endianness bit.
This bug didn't affect execution under TCG because we don't implement
endianness-swapping and so simply ignored the E bit; however it meant
that kernel booting under KVM failed, because KVM does honour the E bit.
Reported-by: Alexey Ignatov <lexszero@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for AArch32 CRC32 and CRC32C instructions added in ARMv8
and add a CPU feature flag to enable these instructions.
The CRC32-C implementation used is the built-in qemu implementation
and The CRC-32 implementation is from zlib. This requires adding zlib
to LIBS to ensure it is linked for the linux-user binary.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1393411566-24104-3-git-send-email-will.newton@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the AArch64 view of the CPACR. The AArch64
CPACR is defined to have a lot of RES0 bits, but since
the architecture defines that RES0 bits may be implemented
as reads-as-written and we know that a v8 CPU will have
no registered coprocessors for cp0..cp13 we can safely
implement the whole register this way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
To avoid complication in code that otherwise would not need to
care about whether EL1 is AArch32 or AArch64, we should store
the interrupt mask bits (CPSR.AIF in AArch32 and PSTATE.DAIF
in AArch64) in one place consistently regardless of EL1's mode.
Since AArch64 has an extra enable bit (D for debug exceptions)
which isn't visible in AArch32, this means we need to keep
the enables in env->pstate. (This is also consistent with the
general approach we're taking that we handle 32 bit CPUs as
being like AArch64/ARMv8 CPUs but which only run in 32 bit mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Define a dummy version of the AArch64 OSLAR_EL1 system register
which just ignores writes. Linux will always write to this (it
is the OS lock used for debugging), but we don't support debug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
In AArch64 the breakpoint and watchpoint registers are mandatory, so the
kernel always accesses them on bootup. Implement dummy versions, which
read as written but have no actual effect.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64-specific ID and feature registers. Although
many of these are currently not used by the architecture (and so
always zero for all implementations), we define the full set of
fields in the ARMCPU struct for symmetry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 MPIDR system register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TTBR* registers. For v7 these were already 64 bits
to handle LPAE, but implemented as two separate uint32_t fields.
Combine them into a single uint64_t which can be used for all purposes.
Since this requires touching every use, take the opportunity to rename
the field to the architectural name.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the A64 view of the VBAR system register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TCR_EL1, which is the 64 bit view of
the AArch32 TTBCR. (The uses of the bits in the register are
completely different, but in any given situation the CPU will
always interpret them one way or the other. In fact for QEMU EL1
is always 64 bit, but we share the state field because this
is the correct mapping to permit a future implementation of EL2.)
We also make the AArch64 view the 'master' as far as migration
and reset is concerned.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the system control register SCTLR_EL1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 memory attribute registers. Since QEMU doesn't
model caches it does not need to care about memory attributes at all,
and we can simply make these read-as-written.
We did not previously implement the AArch32 versions of the MAIR
registers, which went unnoticed because of the overbroad TLB_LOCKDOWN
reginfo definition; provide them now to keep the 64<->32 register
relationship clear.
We already provided AMAIR registers for 32 bit as simple RAZ/WI;
extend that to provide a 64 bit RAZ/WI AMAIR_EL1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
We don't support letting the guest do debug, but Linux prods the
monitor debug system control register anyway, so implement a dummy
RAZ/WI version.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TLB invalidate operations. This is
the full set of TLBI ops defined for a CPU which doesn't
implement EL2 or EL3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement all the AArch64 cache invalidate and clean ops
(which are all NOPs since QEMU doesn't emulate the cache).
The only remaining unimplemented cache op is DC ZVA.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the MIDR system register
(for AArch64 it is a simple constant, unlike the complicated
mess that TI925 imposes on the 32-bit view).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Make the cache ID system registers (CLIDR, CSSELR, CCSIDR, CTR)
visible to AArch64. These are mostly simple 64-bit extensions of the
existing 32 bit system registers and so can share reginfo definitions.
CTR needs to have a split definition, but we can clean up the
temporary user-mode implementation in favour of using the CPU-specified
reset value, and implement the system-mode-required semantics of
restricting its EL0 accessibility if SCTLR.UCT is not set.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The raw read and write functions were using the ARM_CP_64BIT flag in
ri->type to determine whether to treat the register's state field as
uint32_t or uint64_t; however AArch64 register info structs don't use
that flag. Abstract out the "how big is the field?" test into a
function and fix it to work for AArch64 registers. For this to work
we must ensure that the reginfo structs put into the hashtable have
the correct state field for their use, not the placeholder STATE_BOTH.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In ARMv5 level 2 page table descriptors, each 4K or 64K page is split into
four subpages, each of which can have different access permission settings,
which are specified by four two-bit fields in the l2 descriptor. A
long-standing cut-and-paste error meant we were using the wrong bits in
the virtual address to select the access-permission field for 4K pages.
The error has presumably not been noticed before because most guests don't
make use of the ability to set the access permissions differently for
each 1K subpage: if the guest gives the whole page the same access
permissions it doesn't matter which of the 4 AP fields we select.
(The whole issue is irrelevant for ARMv7 CPUs anyway because subpages
aren't supported there.)
Reported-by: Vivek Rai <Vivek.Rai@emulex.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1392667690-8731-1-git-send-email-peter.maydell@linaro.org
Correct some obviously nonsensical bit manipulation spotted by Coverity
when constructing the short-form PAR value for ATS operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1392659525-8335-1-git-send-email-peter.maydell@linaro.org
The write_raw_cp_reg's value argument should be a uint64_t, since
that's what all its callers hand it and what all the functions it
calls take. A (harmless) typo meant we were accidentally declaring
it as int64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The read_raw_cp_reg and write_raw_cp_reg functions can now never
fail (in fact they should never have failed previously unless
there was a bug in a reginfo that meant no raw accessor was
provided for a might-trap register). This allows us to clean up
their prototypes so the write function returns void and the
read function returns the value read, which in turn lets us
simplify the callers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
All cpreg read and write functions now return 0, so we can clean up
their prototypes:
* write functions return void
* read functions return the value rather than taking a pointer
to write the value to
This is a fairly mechanical change which makes only the bare
minimum set of changes to the callers of read and write functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Convert the remaining miscellaneous cases of reginfo read/write
functions returning EXCP_UDEF to use an accessfn instead:
TEEHBR, and the ATS address-translation operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the reginfo structs for the generic timer registers
to use access functions rather than returning EXCP_UDEF from
their read handlers. In some cases this allows us to remove
a read handler completely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Convert the performance monitor reginfo definitions to use
an accessfn rather than returning EXCP_UDEF from read and
write functions. This also allows us to fix a couple of XXX
cases where we weren't imposing the access restrictions on
RAZ/WI or constant registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM946 has 8 PRBS (protection region base and size) registers.
Currently we implement these with a CP_ANY reginfo; however this
underdecodes (since there are 16 possible values of CRm but only
8 registers) and we catch the invalid values in the read and
write functions. However this causes issues with migration since
we only migrate the first of a wildcard register set, so we only
migrate c6_region[0]. It also makes it awkward to pull reginfo
access checks out into their own function.
Avoid all these problems by just defining separate reginfo structs
for each of the 8 registers; this also lets us avoid having any
read or write functions and will result in more efficient direct
field accesses from generated code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SCTLR bits S and R (8 and 9) only exist in ARMv6 and earlier.
In ARMv7 these bits RAZ, and in ARMv8 they are reassigned. Guard
the use of them in check_ap() so that we don't get incorrect results
for ARMv8 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The SCTLR is full of bits for enabling or disabling various things, and so
there are many places in the code which check if certain bits are set.
Define some named constants for the SCTLR bits so these checks are easier
to read.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This helper sets the rounding mode in the standard_fp_status word to
allow NEON instructions to modify the rounding mode whilst using the
standard FPSCR values for everything else.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function will be needed for AArch32 ARMv8 support, so move it to
helper.c where it can be used by both targets. Also moves the code out
of line, but as it is quite a large function I don't believe this
should be a significant performance impact.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for FCVT between half, single and double precision.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This patch adds support for those instructions in the "Floating-point
data-processing (1 source)" group which are simple 32-bit-to-32-bit
or 64-bit-to-64-bit operations (ie everything except FCVT between
single/double/half precision).
We put the new round-to-int helpers in helper.c because they will
also be used by the new ARMv8 A32/T32 rounding instructions.
Signed-off-by: Alexander Graf <agraf@suse.de>
[WN: Commit message tweak, merged single and double precision patches,
updated to new infrastructure.]
Signed-off-by: Will Newton <will.newton@linaro.org>
[PMM: reworked decode, split FCVT out into their own patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This patch adds emulation for the instruction group labeled
"Floating-point <-> fixed-point conversions" in the ARM ARM.
Namely this includes the instructions SCVTF, UCVTF, FCVTZS, FCVTZU
(scalar, fixed-point).
Signed-off-by: Alexander Graf <agraf@suse.de>
[WN: Commit message tweak, rebased, updated to new infrastructure.
Applied bug fixes from Michael Matz and Janne Grunau.]
Signed-off-by: Will Newton <will.newton@linaro.org>
[PMM: significant cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Define the full set of floating point to fixed point conversion
helpers required to support AArch64.
Signed-off-by: Will Newton <will.newton@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The VFP fixed point conversion helpers first call float_scalbn and
then convert the result to an integer. This scalbn operation may
set floating point exception flags for:
* overflow & inexact (if it overflows to infinity)
* input denormal squashed to zero
* output denormal squashed to zero
Of these, we only care about the input-denormal flag, since
the output of the whole scale-and-convert operation will be
an integer (so squashed-output-denormal and overflow don't
apply). Suppress the others by saving the pre-scalb exception
flags and only copying across a potential input-denormal flag.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The VFP conversion helpers for A32 round to zero as this is the only
rounding mode supported. Rename these helpers to make it clear that
they round to zero and are not suitable for use in the AArch64 code.
Signed-off-by: Will Newton <will.newton@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Make the VFP_CONV_FIX helpers a little more flexible in
preparation for the A64 uses. This requires two changes:
* use the correct softfloat conversion function based on itype
rather than always the int32 one; this is possible now that
softfloat provides int16 versions and necessary for the
future conversion-to-int64 A64 variants. This also allows
us to drop the awkward 'sign' macro argument.
* split the 'fsz' argument which currently controls both
width of the input float type and width of the output
integer type into two; this will allow us to specify the
A64 64-bit-int-to-single conversion function, where the
two widths are different.
We can also drop the (itype##_t) cast now that softfloat
guarantees that all the itype##_to_float* functions take
an integer argument of exactly the correct type.
Signed-off-by: Will Newton <will.newton@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
There is an inline duplication of the raw_read and raw_write function
bodies. Fix by just calling raw_read/raw_write instead.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: e69281b7e1462b346cb313cf0b89eedc0568125f.1388649290.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use c13_context field instead of c13_fcse for CONTEXTIDR register
definition.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1387521191-15350-1-git-send-email-s.fedorov@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When setting rounding modes we currently just hardcode the numeric values
for rounding modes in a big switch statement.
With AArch64 support coming, we will need to refer to these rounding modes
at different places throughout the code though, so let's better give them
names so we don't get confused by accident.
Signed-off-by: Alexander Graf <agraf@suse.de>
[WN: Commit message tweak, use names from ARM ARM.]
Signed-off-by: Will Newton <will.newton@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Use the VFP_BINOP macro to provide helpers for min, max, minnum
and maxnum, rather than hand-rolling them. (The float64 max
version is not used by A32 but will be needed for A64.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The common pattern for system registers in a 64-bit capable ARM
CPU is that when in AArch32 the cp15 register is a view of the
bottom 32 bits of the 64-bit AArch64 system register; writes in
AArch32 leave the top half unchanged. The most natural way to
model this is to have the state field in the CPU struct be a
64 bit value, and simply have the AArch32 TCG code operate on
a pointer to its lower half.
For aarch64-linux-user the only registers we need to share like
this are the thread-local-storage ones. Widen their fields to
64 bits and provide the 64 bit reginfo struct to make them
visible in AArch64 state. Note that minor cleanup of the AArch64
system register encoding space means We can share the TPIDR_EL1
reginfo but need split encodings for TPIDR_EL0 and TPIDRRO_EL0.
Since we're touching almost every line in QEMU that uses the
c13_tls* fields in this patch anyway, we take the opportunity
to rename them in line with the standard ARM architectural names
for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement an initial minimal set of EL0-visible system registers:
* NZCV
* FPCR
* FPSR
* CTR_EL0
* DCZID_EL0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The cpregs APIs used by the decoder (get_arm_cp_reginfo() and
cp_access_ok()) currently take either a CPUARMState* or an ARMCPU*.
This is problematic for the A64 decoder, which doesn't pass the
environment pointer around everywhere the way the 32 bit decoder
does. Adjust the parameters these functions take so that we can
copy only the relevant info from the CPUARMState into the
DisasContext and then use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Update the generic cpreg support code to also handle AArch64:
AArch64-visible registers coexist in the same hash table with
AArch32-visible ones, with a bit in the hash key distinguishing
them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
define_one_arm_cp_reg_with_opaque() has a set of nested loops which
insert a cpreg entry into the hashtable for each of the possible
opc/crn/crm values allowed by wildcard specifications. We're about
to add an extra loop to this nesting, so pull the core of the loop
(which adds a single entry to the hashtable) out into its own
function for clarity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Register the aarch64-fpu XML and implement the necessary
read/write handlers so we can support reading and writing
of FP registers in the gdb stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Some processors (notably A9 within Highbank) define and use the
CP15 configuration base address (CBAR). This is vendor specific
so its best implemented as a CPU property (otherwise we would need
vendor specific child classes for every ARM implementation).
This patch prepares support for converting CBAR reset value to
a CPU property by moving the CP registration out of the CPU
init fn, as registration will need to happen at realize time
to pick up any property updates. The easiest way to do this
is via definition of a new ARM_FEATURE to flag the existence
of the register.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 9f697ef1e2ee60a3b9ef971a7f3bc3fa6752a9b7.1387160489.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cp15.c15 space is implementation defined. Currently there is a
dummy placeholder register RAZing it. Allow overriding of this RAZ
so implementations of specific registers can take precedence.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ed1bacec56dae00cb398c798f8240e8e685f949c.1387160489.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current implementation is not accurate according to ARMv7-AR reference
manual. See "B4.1.153 TTBCR, Translation Table Base Control Register,
VMSA | TTBCR format when using the Long-descriptor translation table
format". When LPAE feature is supported, EAE, bit[31] selects
translation descriptor format and, therefore, TTBCR format.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1386657709-23399-1-git-send-email-s.fedorov@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for the ARMv8 floating point VMAXNM and VMINNM
instructions.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1386158099-9239-6-git-send-email-will.newton@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement '-cpu host' for ARM when we're using KVM, broadly
in line with other KVM-supporting architectures.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-11-git-send-email-peter.maydell@linaro.org
Both KVM and TCG populate the cpreg_list with 64 bit register IDs,
but in the TCG side the cpreg_list is sorted using the 32 bit ID
version while in the kvm side the 64 bit ID version is used. This
patch makes the sorting of the cpreg_list consistent between KVM and
TCG.
Signed-off-by: Alvise Rigo <a.rigo@virtualopensystems.com>
Message-id: 1381513125-26802-1-git-send-email-a.rigo@virtualopensystems.com
[PMM: fixed indent, coding style and commit message formatting]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added Vector Base Address remapping on ARM v7.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[PMM: removed spurious mask of value with 1<<31]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since this is only read in cpu_copy() and linux-user has a global
cpu_model, drop the field from generic code.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Avoid the undefined behaviour of "1 << 31" by using 1U to make
the shift be of an unsigned value rather than shifting into the
sign bit of a signed integer. For consistency, we make all the
CPSR_* constants unsigned, though the only one which triggers
undefined behaviour is CPSR_N.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1378391908-22137-3-git-send-email-peter.maydell@linaro.org
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The ARMv7 architecture specifies a 'generic timer' which is implemented
via cp15 registers. Newer kernels will prefer to use this rather than
a devboard-level timer. Implement the generic timer for TCG; for KVM
we will already use the hardware's virtualized timer for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1376065080-26661-4-git-send-email-peter.maydell@linaro.org
Extend the raw_read() and raw_write() helper accessors so that
they can be used for 64 bit registers as well as 32 bit registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 1376065080-26661-2-git-send-email-peter.maydell@linaro.org
The 'int' loglevel for recording interrupts and exceptions
requires support in the target-specific code. Implement
it for ARM. This improves debug logging in some situations
that were otherwise pretty opaque, such as when we fault
trying to execute at an exception vector address, which
would otherwise cause an infinite loop of taking exceptions
without any indication in the debug log of what was going on.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1375700771-21665-1-git-send-email-peter.maydell@linaro.org
