The GIC spec states that only interrupts with higher priority
than the value in the GICC_PMR priority mask register are
passed through to the processor. We were incorrectly allowing
through interrupts with a priority equal to the specified
value: correct the comparison operation to match the spec.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@samsung.com>
Fix the code in the secondary CPU boot stubs so that it correctly
initialises the GIC rather than relying on bugs or implementation
dependent aspects of the QEMU GIC implementation:
* set the GIC_PMR.Priority field to all-ones, so that all
interrupts are passed through. The default of all-zeroes
means all interrupts are masked, and QEMU only booted because
of a bug in the priority masking in our GIC implementation.
* add a barrier after GIC setup and before WFI to ensure that
GIC config is complete before we go into a possible low power
state. This isn't needed with the software GIC model but could
be required when using KVM and executing this code on the
real hardware CPU.
Note that of the three secondary stub implementations, only
the common generic one needs to support both v6 and v7 DSB
encodings; highbank and exynos4210 will always be v7 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@samsung.com>
There are QEMUMachines that have neither IF_IDE nor IF_SCSI as a
default/standard interface to their block devices / drives. Therefore,
this patch introduces a new field default_block_type per QEMUMachine
struct. The prior use_scsi field becomes thereby obsolete and is
replaced through .default_block_type = IF_SCSI.
This patch also changes the default for s390x to IF_VIRTIO and
removes an early hack that converts IF_IDE drives.
Other parties have already claimed interest (e.g. IF_SD for exynos)
To create a sane default, for machines that dont specify a
default_block_type, this patch makes IF_IDE = 0 and IF_NONE = 1.
I checked all users of IF_NONE (blockdev.c and ww/device-hotplug.c)
as well as IF_IDE and it seems that it is ok to change the defines -
in other words, I found no obvious (to me) assumption in the code
regarding IF_NONE==0. IF_NONE is only set if there is an
explicit if=none. Without if=* the interface becomes IF_DEFAULT.
I would suggest to have some additional care, e.g. by letting
this patch sit some days in the block tree.
Based on an initial patch from Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Igor Mitsyanko <i.mitsyanko@samsung.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Igor Mitsyanko <i.mitsyanko@samsung.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For the virtio-blk device (via virtio-pci) the property "config-wce" is
defined in two places. First, it's defined from the
DEFINE_VIRTIO_BLK_FEATURES macro, second it's defined directly in
virtio-pci, just two lines above the call to that macro.
The direct definition in virtio-pci.c is broken, since it operates on the
'config_wce' field of VirtIOBlkConf, which is never used anywhere else.
Therefore, this patch removes both the extra property definition and the
redundant field it works on.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Paul 'Rusty' Russell <rusty@rustcorp.com.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
kvm_irqchip_in_kernel() has an architecture specific meaning, so
we shouldn't be using it to determine whether to enabled KVM INTx
bypass. kvm_irqfds_enabled() seems most appropriate. Also use this
to protect our other call to kvm_check_extension() as that explodes
when KVM isn't enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org
* afaerber/qom-cpu:
target-i386: Postpone cpuid_level update to realize time
target-i386: Use define for cpuid vendor string size
target-i386: Separate feature string parsing from CPU model lookup
target-i386/cpu.c: Coding style fixes
qdev: qdev_create(): use error_report() instead of hw_error()
sysemu.h: Include qemu-types.h instead of qemu-common.h
Create qemu-types.h for struct typedefs
qlist.h: Do not include qemu-common.h
qga/channel-posix.c: Include headers it needs
qapi/qmp-registry.c: Include headers it needs
ui/vnc-palette.c: Include headers it needs
user: Rename qemu-types.h to qemu-user-types.h
user: Move *-user/qemu-types.h to main directory
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/acpi.1:
acpi: drop debug port
q35: update lpc pci config space according to configured devices
apci: switch piix4 pci hotplug to memory api
acpi: remove acpi_gpe_blk
apci: switch piix4 gpe to memory api
acpi: fix piix4 smbus mapping
acpi: switch smbus to memory api
acpi: cleanup ich9 memory region
apci: switch ich9 smi to memory api
apci: switch ich9 gpe to memory api
acpi: cleanup vt82c686 memory region
acpi: cleanup piix4 memory region
apci: switch evt to memory api
apci: switch cnt to memory api
apci: switch timer to memory api
apci: switch vt82c686 to memory api
apci: switch ich9 to memory api
apci: switch piix4 to memory api
Conflicts:
hw/lpc_ich9.c
Resolved merge conflict due to apm_init adding an argument.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.74:
usb-tablet: Allow connecting to ehci
ehci: Lower timer freq when the periodic schedule is idle
usb: Allow overriding of usb_desc at the device level
usb: Don't allow USB_RET_ASYNC for interrupt packets
usb: Call wakeup when data becomes available for all devices with int eps
add pc-1.4
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* 'master' of git.qemu-project.org:/pub/git/qemu:
target-mips: Fix incorrect shift for SHILO and SHILOV
target-mips: Fix incorrect code and test for INSV
xilinx_uartlite: Accept input after rx FIFO pop
xilinx_uartlite: suppress "cannot receive message"
xilinx_axienet: Implement R_IS behaviour
Harmless, because we the error inevitably leads to another, fatal one
in pc_system_flash_init(): PC system firmware (pflash) not available.
Fix it anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
These spelling bugs were found by codespell:
supressing -> suppressing
transfered -> transferred
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
pci_drive_hot_add() parameter type has the wrong type: int instead of
BlockInterfaceType. It's actually redundant, so we can just drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
I'm guessing this is a hangover from a previous coreification of the mptimer
sub-module. This field is completely unused - removed.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some debug printfs for SD are coming up in stdout. Redirected them to stderr
instead.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
hw_error() is specific for fatal hardware emulation errors, not for
internal errors related to the qdev object/class abstraction or object
initialization.
Replace it with an error_report() call, followed by abort().
This will also help reduce dependencies of the qdev code (as hw_error()
is from cpus.o, and depends on the CPU list from exec.o).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Instead of keeping all those struct typedefs in qemu-common.h, move it
to a header that can be safely included by other headers, containing
only the struct typedefs and not pulling in other dependencies.
Also, move some of the qdev-core.h typedefs to the new file, too, so
other headers don't need to include qdev-core.h only because of
DeviceState and other typedefs.
This will help us remove qemu-common.h dependencies from some headers
later.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The device return false from the can receive function when the FIFO is
full. This mean the device should check for buffered input whenever a byte is
popped from the FIFO.
Reported-by: Jason Wu <huanyu@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
This message is not an error condition, its just informing the user that
the device is corking the uart traffic to not drop characters.
Reported-by: Jason Wu <huanyu@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
The interrupt status register R_IS is the standard clear-on-write behaviour.
This was unimplemented and defaulting to updating the register to the written
value. Implemented clear-on-write.
Reported-by: Jason Wu <huanyu@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Replace all register_ioport_*() with the new Memory API functions.
This permits to use the new Memory stuff like listeners.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
[AF: Rebased onto hwaddr]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace all register_ioport_*() with portio_*() or a MemoryRegion.
This permits to use the new Memory stuff like listeners.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
[AF: Rebased onto hwaddr]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace all register_ioport_*() with a MemoryRegion.
This permits to use the new Memory stuff like listeners.
For more flexibility, the IO address space is passed as an argument.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
[AF: Rebased onto serial split]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace all register_ioport_*() with the new Memory API.
This permits to use the new Memory stuff like listeners.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
[AF: Rebased onto hwaddr]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace all register_ioport_*() with a MemoryRegion.
This permits to use the new Memory stuff like listeners.
Moreover, the PCI device is added as an argument for apm_init(),
so we can register IO inside the PCI IO address space.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
[AF: Rebased onto hwaddr and q35]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This function permits to retrieve ISA IO address space.
It will be usefull when we need to pass IO address space as argument.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Our ehci code has is capable of significantly lowering the wakeup rate
for the hcd emulation while the device is idle. It is possible to add
similar code ot the uhci emulation, but that simply is not there atm,
and there is no reason why a (virtual) usb-tablet can not be a USB-2 device.
Making usb-hid devices connect to the emulated ehci controller instead
of the emulated uhci controller on vms which have both lowers the cpuload
for a fully idle vm from 20% to 2-3% (on my laptop).
An alternative implementation to using a property to select the tablet
type, would be simply making it a new device type, ie usb-tablet2, but the
downside of that is that this will require libvirt changes to be available
through libvirt at all, and then management tools changes to become the
default for new vms, where as using a property will automatically get
any pc-1.3 type vms the lower cpuload.
[ kraxel: adapt compat property for post-1.3 merge ]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
tablet compat fixup
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Lower the timer freq if no iso schedule packets complete for 64 frames in
a row.
We can safely do this, without adding latency, because:
1) If there is isoc traffic this will never trigger
2) For async handled interrupt packets (only usb-host), the completion handler
will immediately schedule the frame_timer from a bh
3) All devices using NAK to signal no data for interrupt endpoints now use
wakeup, which will immediately schedule the frame_timer from a bh
The advantage of this is that when we only have interrupt packets in the
periodic schedule, async_stepdown can do its work and significantly lower
the frequency at which the frame_timer runs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This allows devices to present a different set of descriptors based on
device properties.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It is tempting to use USB_RET_ASYNC for interrupt packets, rather then the
current NAK + polling approach, but this causes issues for migration, as
an async completed packet will not getting written back to guest memory until
the next poll time, and if a migration happens in between it will get lost!
Make an exception for host devices, because:
1) host-linux actually uses async completion for interrupt endpoints
2) host devices don't migrate anyways
Ideally we would convert host-linux.c to handle (input) interrupt endpoints in
a buffered manner like it does for isoc endpoints, keeping multiple urbs
submitted to ensure the devices timing requirements are met, as well as making
its interrupt ep handling the same as other usb-devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is necessary for proper interaction with the xhci controller, and it
will allow other hcds to lower there frame timer while waiting for interrupt
data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
I'm pretty sure this isn't needed any more. I think this predates the
switch to seabios, and the seabios DSDT table has a DBUG() aml macro
which writes stuff to the seabios debug port (0x402).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The e1000_receive function for the e1000 needs to discard packets longer than
1522 bytes if the SBP and LPE flags are disabled. The linux driver assumes
this behavior and allocates memory based on this assumption.
Signed-off-by: Michael Contreras <michael@inetric.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kwolf/for-anthony:
coroutine-sigaltstack.c: Use stack_t, not struct sigaltstack
stream: fix ratelimit_set_speed
atapi: make change media detection for guests easier
Documentation: Update image format information
Documentation: Update block cache mode information
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.73:
ehci-sysbus: Attach DMA context.
usb: fail usbdevice_create() when there is no USB bus
usb: tag usb host adapters as not hotpluggable.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If you have a guest with a media in the optical drive and you change
it, the windows guest cannot properly recognize this media change.
Windows needs to detect sense "NOT_READY with ASC_MEDIUM_NOT_PRESENT"
before we send sense "UNIT_ATTENTION with ASC_MEDIUM_MAY_HAVE_CHANGED".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 0d8d769085 introduced
a regression in virtio-net performance because it looks
into the ring aggressively while we really only care
about a single packet worth of buffers.
Reported as bugzilla 1066055 in launchpad.
To fix, add parameters limiting lookahead, and
use in virtqueue_avail_bytes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Edivaldo de Araujo Pereira <edivaldoapereira@yahoo.com.br>
Tested-by: Edivaldo de Araujo Pereira <edivaldoapereira@yahoo.com.br>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We are currently checking for an exact type match. Use QOM dynamic_cast to
check for a compatible type instead.
Cc: Konrad Frederic <fred.konrad@greensocs.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
---
v1 -> v2:
- also add cast to qbus_find_recursive (Peter)
- simplify by doing object_dynamic_cast instead of messing with classes
This was left as NULL on the initial merge due to debate on the mailing list on
how to handle DMA contexts for sysbus devices. Patch
9e11908f12 was later merged to fix OHCI. This is the,
equivalent fix for sysbus EHCI.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Report an error instead of segfaulting when attaching a USB device to a
machine with no USB busses:
$ qemu-system-arm -machine vexpress-a9 \
-sd Fedora-17-armhfp-vexpress-mmcblk0.img \
-kernel vmlinuz-3.4.2-3.fc17.armv7hl \
-initrd initramfs-3.4.2-3.fc17.armv7hl.img \
-usbdevice disk:format=raw:test.img
Note that the vexpress-a9 machine does not have a USB host controller.
Reported-by: David Abdurachmanov <David.Abdurachmanov@cern.ch>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Hotplugging them simply doesn't work, so tag them accordingly to
avoid users trying and then crashing qemu.
For xhci there is nothing fundamental which prevents hotplug from
working, we'll "only" need a exit() function which cleans up
everything properly. That isn't for 1.3 though.
For ehci+uhci+ohci hotplug can't be supported until qemu gains the
capability to hotplug multifunction pci devices.
https://bugzilla.redhat.com/show_bug.cgi?id=879096
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The devram memslot stays active when qxl enters UNDEFINED mode (i.e, no
primary surface). If migration has occurred while the device is in
UNDEFINED stae, the memslots have to be reloaded at the destination.
Fixes rhbz#874574
Signed-off-by: Yonit Halperin <yhalperi@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* bonzini/scsi-next:
virtio-scsi: Fix subtle (guest) endian bug
virtio-scsi: Fix some endian bugs with virtio-scsi
iscsi: do not assume device is zero initialized
iscsi: fix deadlock during login
iscsi: fix segfault in url parsing
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* agraf/s390-for-upstream-1.3:
sclp: Fix uninitialized var in handle_write_event_buf().
s390: Fix ram_size updating in machine init
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-scsi config space is, by specification, in guest endian (which
is ill-defined, but there you go). In virtio_scsi_get_config() we set up
all the fields in there, using stl_raw(). Which is a problem for the
max_channel and max_target fields, which are 16-bit, not 32-bit. For
little-endian targets we get away with it by accident, since the first
two bytes will still be correct, and the extra two bytes written (with
zeroes) will be overwritten correctly by the next store.
But for big-endian guests, this means the max_target field ends up as zero,
which means the guest will only recognize a single disk on the virtio-scsi
bus. This patch fixes the problem.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul 'Rusty' Russell <rusty@rustcorp.com.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The virtio-scsi specification does not specify the correct endianness for
fields in the request structure. It's therefore best to assume that it is
"guest native" endian since that's the (stupid and poorly defined) norm in
virtio.
However, the qemu device for virtio-scsi has no byteswaps at all, and so
will break if the guest has different endianness from the host. This patch
fixes it by adding tswap() calls for the sense_len and resid fields in
the request structure. In theory status_qualifier needs swaps as well,
but that field is never actually touched. The tag field is a uint64_t, but
since its value is completely arbitrary, it might as well be uint8_t[8]
and so it does not need swapping.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul 'Rusty' Russell <rusty@rustcorp.com.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This bug occurs when the SET flag of Register B is enabled. When an RTC
data register (i.e. any of the ten time/calender CMOS bytes) is set, the
data is (as expected) correctly stored in the cmos_data array. However,
since the SET flag is enabled, the function rtc_set_time is not invoked.
As a result, the field base_rtc in RTCState remains uninitialized. This
causes a problem on subsequent writes which can end up overwriting data.
To see this, consider writing data to Register A after having written
data to any of the RTC data registers; the following figure illustrates
the call stack for the Register A write operation:
+- cmos_io_port_write
+-- check_update_timer
+---- get_next_alarm
+------ rtc_update_time
In rtc_update_time, get_guest_rtc calculates the wrong time and
overwrites the previously written RTC data register values.
Signed-off-by: Alex Horn <alex.horn@cs.ox.ac.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
g_assert_cmpint is not available on glib 2.12, which is the minimum
version required to build QEMU (we only require 2.16 to run tests,
since that is the first version including GTester). Do not use it
in hardware models, use a normal assertion instead.
This fixes the buildbot failure for default_x86_64_rhel5.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix typos, whitespace and update comments to match current
implementation.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Disable the rate-limit timer on device remove (e.g. hot-unplug).
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If we got fewer bytes from the backend than requested, don't poke the
backend for more bytes; the guest will ask for more (or if the guest has
already asked for more, the backend knows about it via handle_input()).
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Popping an elem from the vq just to find out its length causes problems
with save/load later on. Use the new virtqueue_get_avail_bytes()
function instead, saves us the complexity in the migration code, as well
as makes the migration endian-safe.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It used a wrong struct type name since its introduction in
8f04ee0882 (isa: pic: convert to QEMU
Object Model), apparently it is unused so far.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All conditional deallocation can now be done with object_delete.
Remove the @qom_allocated and @glib_allocated fields; replace the latter
with a direct assignment of the @free function pointer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add an ObjectClass method that is done at object_unparent time. It
should remove any backlinks to the object in the composition tree,
so that object_delete will be able to drop the last reference and
free the object.
Use it for qdev buses.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some gcc versions rightly complain about a possibly unitialized rc,
so let's move setting it before the QTAILQ_FOREACH().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The global variable 'ram_size' is hidden by the local variable
declaration in s390_init(). Since we want to update the global
ram size in certain cases we must not use a local ram_size
variable.
- This fixes booting with unusual ram sizes like -m 67001
- This changes behaviour back to the situation before commit
5f072e1f30
(create struct for machine initialization arguments)
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
In one of the recent reworks to the XICS code, a bug was introduced where
we use the wrong sense and allocate level interrupts instead of message
interrupts for PCI MSIs. This patch fixes it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pass qemu_sglist_init the global dma_context_memory rather than a NULL
pointer; this fixes a segfault in dma_memory_map() when the guest
starts using DMA.
Reported-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 0d93692 (qdev: Convert busses to QEMU Object Model, 2012-05-02)
removed a check on the type of the bus where a SCSI disk is hotplugged.
However, hot-plugging to the wrong kind of device now causes a crash
due to either a NULL pointer dereference (avoided by the previous patch)
or a failed QOM cast.
Instead, in this case we need to use object_dynamic_cast and check for
the result, similar to what was done before that commit.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avoid passing a non-PCI IRQ to ich9_gsi_to_pirq. It's wrong and triggers
an assertion.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Same as for i44fx: KVM does not support SMM yet. Signal it initialized
to Seabios to avoid failures.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the dmi-to-pci i82801b11 bridge chip. This is the pci bridge chip
that q35 uses on its host bus for PCI bus arbitration.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pc q35 based chipset emulator to support pci express natively. Based on
Anthony Liguori's suggestion, the machine name is 'q35-next', with an alias
of 'q35'. At this point, there are no compatibility guarantees. When the
chipset stabilizes more, we will begin to version the machine names.
Major features which still need to be added:
-Migration support (mostly around ahci)
-ACPI hotplug support (pcie hotplug support is working)
-Passthrough support
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add support for the ich9 smbus chip.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add support for the ICH9 LPC chip.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Lay the groundwork for subsequent ich9 support.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Factor out smram/pam logic for use by other chipsets, namely q35
at this point.
Note: Should be factored out into a generic North Bridge Class.
[jbaron@redhat.com: changes for updated memory API]
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename: kvm_piix3_gsi_handlei() -> kvm_pc_gsi_handler()
kvm_piix3_setup_irq_routing() -> kvm_pc_setup_irq_routing()
This is in preparation for other users, namely q35 at this time.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move ioapic_init() from pc_piix.c to pc.c, to make it a common function.
Rename ioapic_init() -> ioapic_init_gsi().
Move to pc.h so q35 can use them as well.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Factor out pc nic initialization.
This simplifies the pc initialization and will reduce the code
duplication of q35 pc initialization.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.72:
usb-redir: Don't handle interrupt output packets async
usb-redir: Split usb_handle_interrupt_data into separate in/out functions
usb-smartcard-reader: Properly NAK interrupt eps when we've no events
usb-bt: Return NAK instead of STALL when interrupt ep has no data
uhci: Fix double unlink
uhci: Don't allow the guest to set port-enabled when there is no dev connected
uhci: Add a completions_only flag for async completions
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead report them as successfully completed directly on submission, this
has 2 advantages:
1) This matches the timing of interrupt output packets on real hardware,
with the previous async handling, if an ep has an interval of say 500 ms,
then there would be 500+ ms between the submission and the guest seeing the
completion, as we wont do the write back until the qh gets polled again. And
in the mean time the guest may very well have timed out, as the guest can
reasonable expect a much quicker completion.
2) This fixes interrupt output packets potentially getting send twice
surrounding a migration. As we delay the writeback to guest memory until
the qh gets polled again, there is a window between completion and writeback
where migration can happen, in this case the destination will not know
about the completion, and it will execute the packet *again*
But it does also come with a disadvantage:
1) If the actual interrupt out to the real usb device fails, there is no
way to report this back to the guest.
This patch assumes however that interrupt outs in practice never fail, as
they are only used by specialized drivers, which are unlikely to issue illegal
requests (unlike general class drivers which often issue requests which some
devices don't implement). And that thus the advantages outway the disadvantage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When we've no data to return from the interrupt endpoint, return NAK rather
then a 0 length packet.
CC: Alon Levy <alevy@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
I noticed this while making all devices with interrupt endpoints properly
do wakeup. While at it also add wakeup support.
Note that I've not tested this, but returning STALL for an interrupt ep
which has no data is cleary the wrong thing to do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
uhci_async_cancel() already does a uhci_async_unlink().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It is possible for device disconnect and the guest trying to reset the port
(because of USB xact errors prior to the disconnect getting signaled) to race,
when we hit this race, the guest will write the port-control register with its
pre-disconnect value + the reset bit set, after which we have a disconnected
device with its port-enabled bit set in its port-control register, which
is no good :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a completions_only flag, and set this when running process_frame for async
completion handling, this fixes 2 issues in a single patch:
1) It makes sure async completed packets get written to guest mem immediately,
even if all the bandwidth for the frame was consumed from the timer run
process_frame. This is necessary as delaying their writeback to the next frame
can cause the completion to get lost on migration.
2) The calling of process_frame from a bh on async completion causes iso
tds to get server more often they should, messing up usb sound class device
timing. By only processing completed packets, the iso tds get skipped fixing
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When failing a request because the length of the regions described by
the PRDT was too short for the requested number of sectors, the IDE
emulation forgot to update the status register, so that the device would
keep the BSY flag set indefinitely.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Without this, s->nsector can become negative and badness happens (trying
to malloc huge amount of memory and glib calls abort())
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* kwolf/for-anthony: (26 commits)
qemu-io: Use bdrv_drain_all instead of qemu_aio_flush
megasas: Use bdrv_drain_all instead of qemu_aio_flush
vmdk: Fix data corruption bug in WRITE and READ handling
fdc: remove last usage of FD_STATE_SEEK
fdc: fix typo in zero constant
fdc: remove double affectation of FD_MSR_CMDBUSY flag
fdc-tests: add tests for VERIFY command
fdc: implement VERIFY command
fdc-test: Check READ ID
fdc: fix false FD_SR0_SEEK
fdc: fix FD_SR0_SEEK for initial seek on DMA transfers
fdc: fix FD_SR0_SEEK for non-DMA transfers and multi sectors transfers
fdc: use status0 field instead of a local variable
fdc-test: add tests for non-DMA READ command
fdc-test: insert media before fuzzing registers
fdc-test: split test_media_change() test, so insert part can be reused
fdc: Remove status0 parameter from fdctrl_set_fifo()
aio: rename AIOPool to AIOCBInfo
aio: use g_slice_alloc() for AIOCB pooling
aio: switch aiocb_size type int -> size_t
...
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.71:
usb-host: fix splitted transfers
usb-host: update tracing
usb-redir: Set default debug level to warning
usb-redir: Only add actually in flight packets to the in flight queue
ehci: handle dma errors
ehci: keep the frame timer running in case the guest asked for frame list rollover interrupts
ehci: Don't verify the next pointer for periodic qh-s and qtd-s
ehci: Better detection for qtd-s linked in circles
ehci: Fixup q->qtdaddr after cancelling an already completed packet
ehci: Don't access packet after freeing it
usb: host-linux: Ignore parsing errors of the device descriptors
usb-host: scan for usb devices when the vm starts
usb: Fix (another) bug in usb_packet_map() for IOMMU handling
fix live migration
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* afaerber/qom-cpu:
target-i386: Add Haswell CPU model
target-i386/cpu: Add new Opteron CPU model
target-i386/cpu: Name new CPUID bits
qapi-types.h: Don't include qemu-common.h
osdep: Move qemu_{open,close}() prototypes
qemu-config.h: Include headers it needs
vnc-palette.h: Include <stdbool.h>
qemu-fsdev-dummy.c: Include module.h
qdev: Split up header so it can be used in cpu.h
Move qemu_irq typedef out of qemu-common.h
qemu-common.h: Comment about usage rules
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* qemu-kvm/uq/master:
kvm: Actually remove software breakpoints from list on cleanup
acpi_piix4: fix migration of gpe fields
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows you to specify:
$ qemu -device virtio-rng-pci
And things will Just Work with a reasonable default.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds parameters to virtio-rng-pci to allow rate limiting the entropy a
guest receives. An example command line:
$ qemu -device virtio-rng-pci,max-bytes=1024,period=1000
Would limit entropy collection to 1Kb/s.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The Linux kernel already has a virtio-rng driver, this is the device
implementation.
When the guest asks for entropy from the virtio hwrng, it puts a buffer
in the vq. We then put entropy into that buffer, and push it back to
the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
---
aliguori: converted to new RngBackend interface
aliguori: remove entropy needed event
aliguori: fix migration
Now that we have separate status and length fields in USBPacket
update the completion tracepoint to log both.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The previous default of 0 means that even errors and warnings would not
get printed, which is really not a good default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Packets which are queued up, but not yet handed over to the device, are
*not* in flight.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Starting with commit 1c380f9460 dma
transfers can actually fail. This patch makes ehci keep track
of the busmaster bit in pci config space, by setting/clearing the
dma_context pointer. Attempts to dma without context will result
in raising HSE (Host System Error) interrupt and stopping the host
controller.
This patch fixes WinXP not booting with a usb stick attached to ehci.
Root cause is seabios activating ehci so you can boot from the stick,
and WinXP clearing the busmaster bit before resetting the host
controller, leading to ehci actually trying dma while it is disabled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
While testing the move to async packet handling for interrupt endpoints I
noticed that Windows-XP likes to play tricks with the next pointer for
periodic qh-s, so we should not fail qh / qtd verification when it changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Windows links interrupt qtd-s in circles, which means that when interrupt
endpoints return USB_RET_ASYNC, combined with the recent
"ehci: Retry to fill the queue while waiting for td completion" patch,
we keep adding the tds to the queue over and over again, as we detect the
circle from fill_queue, but we call it over and over again ...
This patch fixes this by changing the circle detection to also detect
circling into tds already queued up previously.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This avoids the q->qtdaddr == p->qtdaddr asserts we have triggering, when
a queue contains multiple completed packages when we cancel the queue.
I triggered this with windows7 + async interrupt endpoint handling (*)
+ not detecting circles in ehci_fill_queue() properly, which makes the qtd
validation in ehci_fill_queue fail, causing cancellation of the queue on every
mouse event ...
*) Which is not going upstream as it will cause loss of interrupt events on
migration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ehci_state_writeback() will free the packet, so we should not access
the packet after calling ehci_state_writeback().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The Linux is more tolerant here as well: Just stop parsing the device
descriptors when an error is detected but do not reset what was found
so far. This allows to run buggy devices with partially invalid
descriptors.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bochs dispi interface traditionally uses port 0x1ce as 16bit index
register and port 0x1cf as 16bit data register. The later is unaligned,
and probably for that reason the the data register was moved to 0x1d0
for non-x86 archs.
This patch makes the data register available at 0x1d0 on x86 too. The
old x86 location is kept for compatibility reasons, so both 0x1cf and
0x1d0 can be used as data register on x86.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit a844ed842d leads to usb-host
detecting devices not right after qemu startup because the guest
isn't running yet. Instead they are found on the first of the
regular usb device poll runs. Which is too late for seabios to see
them, so booting from usb sticks fails.
Fix this by adding a vm state change handler which triggers a device
scan when the vm is started.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Elements in qemu SGLists can cross IOMMU page boundaries. So, in commit
39c138c842 "usb: Fix usb_packet_map() in the
presence of IOMMUs", I changed usb_packet_map() to split up each SGList
element on IOMMU page boundaries and each resulting piece of qemu's memory
space separately to the iovec the usb code uses internally.
That was correct in concept, but the patch has a bug. The 'base' variable
correctly steps through the dma address of each piece, but then we call
the dma_memory_map() function on the base address of the whole SGList
element every time.
This patch fixes at least one problem using XHCI on the pseries guest
machine. It didn't affect OHCI because that doesn't use usb_packet_map().
In theory it also affects EHCI, but we haven't observed that in practice.
I think the transfers were small enough on EHCI that they never crossed an
IOMMU page boundary in practice.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 1c380f9460 breaks live migration.
DMA stops working for ehci (and probably for any pci device) after
restoring the guest because the bus master region never gets enabled.
Add code doing that after loading the pci config space from vmstate.
Cc: Avi Kivity <avi@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Alexander Larsson found irq injection to Windows guests stopped after a
migration. The symptom was the mouse stopped working.
Reproduction steps are:
1. On src, start qemu with a virtio-serial port without any backend
2. On dest, start qemu with a virtio-serial port with a backend
3. Migrate.
Upon migration, the older code detected the change in backend connection
status, and sent a notification to the guest. However, it's not
guaranteed that the apic is ready to inject irqs into the guest, and the
irq line remained high, resulting in any future interrupts going
unnoticed by the guest as well.
Add a new timer based on vm_clock for 1 ns in the future from post_load
to do the event send in case host_connected differs between migration
source and target.
RHBZ: 867366
Signed-off-by: Alon Levy <alevy@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com> # verbose commit log
According to the MIPS Malta Developement Platform User's Manual, the
i8259 interrupt controller is supposed to be connected to the hardware
IRQ0, and the CBUS UART to the hardware interrupt 2.
In QEMU they are both connected to hardware interrupt 0, the CBUS UART
interrupt being wrong. This patch fixes that. It should be noted that
the irq array in QEMU includes the software interrupts, hence
env->irq[2] is the first hardware interrupt.
Cc: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Header file dependency is a frickin' nightmare right now. cpu.h tends
to get included in our 'include everything' header files but qdev also
needs to include those headers mainly for qdev-properties since it knows
about CharDriverState and friends.
We can solve this for now by splitting out qdev.h along the same lines
that we previously split the C file. Then cpu.h just needs to include
qdev-core.h.
hw/qdev.h is split into following new headers:
hw/qdev-core.h
hw/qdev-properties.h
hw/qdev-monitor.h
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
[ehabkost: re-add DEFINE_PROP_PCI_HOST_DEVADDR, that was removed on the
original patch (by mistake, I guess)]
[ehabkost: kill qdev_prop_set_vlan() declaration]
[ehabkost: moved get_fw_dev_path() comment to the original location
(I don't know why it was moved)]
[ehabkost: removed qdev_exists() declaration]
[ehabkost: keep using 'QemuOpts' instead of 'struct QemuOpts', as
qdev-core.h includes qemu-option.h]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
It's necessary for making CPU child of DEVICE without
causing circular header deps.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[ehabkost: re-added the typedef to hw/irq.h after rebasing]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Migrate 16 bytes for en/sts fields (which is the correct size),
increase version to 3, and document how to support incoming
migration from qemu-kvm 1.2.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Calling qemu_aio_flush() directly can hang when combined with I/O
throttling.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Replace it by directly setting FD_SR0_SEEK if required
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
FD_MSR_CMDBUSY flag is already set in fdctrl_write_data(), just
before calling the command handler (fdctrl_start_transfer() here).
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VERIFY command is like a READ command, except that read data is not
transfered by DMA.
As DMA engine is not used, so we have to start data transfer ourselves.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Do not always set FD_SR0_SEEK, as callers already set it if needed.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
fdctrl_start_transfer() used to set FD_SR0_SEEK no matter if
there actually was a seek or not. This is obviously wrong.
fdctrl_start_transfer() has this information because it performs
the initial seek itself.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On non-DMA transfers, fdctrl_stop_transfer() used to set FD_SR0_SEEK
no matter if there actually was a seek or not. This is obviously wrong.
fdctrl_seek_to_next_sect() has this information because it performs
the seek itself.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It decided whether an interrupt is triggered. Only one caller made use
of this functionality, so move the code there.
In this one caller, the interrupt must actually be triggered
unconditionally, like it was before commit 2fee0088. For example, a
successful read without an implied seek can result in st0 = 0, but still
triggers the interrupt.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Now that AIOPool no longer keeps a freelist, it isn't really a "pool"
anymore. Rename it to AIOCBInfo and make it const since it no longer
needs to be modified.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* bonzini/scsi-next:
virtio-scsi: use dma_context_memory
dma: Define dma_context_memory and use in sysbus-ohci
megasas: Correct target/lun mapping
scsi-disk: flush cache after disabling it
megasas: do not include block_int.h
scsi: remove superfluous call to scsi_device_set_ua
virtio-scsi: factor checks for VIRTIO_SCSI_S_DRIVER_OK when reporting events
scsi: do not return short responses for emulated commands
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.70:
ehci: fix migration
xhci: Fix some DMA host endian bugs
usb/combined-packet: Move freeing of combined to usb_combined_packet_remove()
xhci: Add support for packets with both data and an error status
ehci: Add support for packets with both data and an error status
ehci: Get rid of the magical PROC_ERR status
usb-redir: Allow packets to have both data and an error-status
usb: split packet result into actual_length + status
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This makes use of the new level irqfd support enabling bypass of qemu
userspace both on INTx injection and unmask. This significantly
boosts the performance of devices making use of legacy interrupts (ex.
~60% better netperf TCP_RR scores for an e1000e assigned to a Linux
guest and booted with pci=nomsi). This also avoids flipping mmaps on
and off to simulate EOIs, so greatly improves performance of device
access in addition to interrupt latency.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Until address_space_rw was introduced, NULL was accepted as a
placeholder for DMA with no IOMMU (to address_space_memory).
This does not work anymore, and dma_context_memory needs to
be specified explicitly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Define a new global dma_context_memory which is a DMAContext corresponding
to the global address_space_memory AddressSpace. This can be used by
sysbus peripherals like sysbus-ohci which need to do DMA.
In particular, use it in the sysbus-ohci device, which fixes a
segfault when attempting to use that device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The structure to reference a logical drive has an unused field,
which can be used to carry the lun ID. This enabled seabios to
establish the proper target/LUN mapping.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SBC says that "if an application client changes the WCE bit from one to
zero via a MODE SELECT command, then the device server shall write
any data in volatile cache to non-volatile medium before completing
the command".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The inquiry command, for the case of VPD=1, was returning short
responses; the number of returned bytes was just the number of bytes
in the request, without padding to the specified allocation length
with zero bytes. This is usually harmless, but it is a violation
of the SCSI specification.
To fix this, always pad with zero bytes to r->cmd.xfer in
scsi_disk_emulate_command, and return at most r->buflen bytes
(the size of the buffer for command data) rather than at most
buflen bytes (the number of bytes that was filled in).
Before this patch, "strace sg_inq -p0x83 /dev/sda" would report a
non-zero resid value. After this patch, it reports resid=0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Keep saving display surface parameters at init and using these cached
values instead of getting them when needed. Not sure why this is
needed (maybe due to the interaction with the vga device) but not
doing this broke the Xorg vmware driver at least.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Since 0b57e287, cpu_memory_rw_debug already triggers a TB invalidation.
As it doesn't (and cannot) set is_cpu_write_access=1 but "consumes" the
currently executed TB, the tb_invalidate_phys_page_range call from
patch_instruction didn't work anymore.
Fix this by open-coding the required bits to restore the CPU state from
the current TB position before patching and resume execution on the
patched instruction afterward.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The xhci device does correct endian switches on the results of some DMAs
but not all. In particular, there are many DMAs of what are essentially
arrays of 32-bit integers which never get byteswapped. This causes them
to be interpreted incorrectly on big-endian hosts, since (as per the xhci
spec) these arrays are always little-endian in guest memory.
This patch adds some helper functions to fix these bugs. This may not be
all the endian bugs in the xhci code, but it's certainly some of them and
the Linux guest xhci driver certainly gets further with these fixes.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Instead make ehci_execute and ehci_fill_queue return the again value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since with the ehci and xhci controllers a single packet can be larger
then maxpacketsize, it is possible for the result of a single packet
to be both having transferred some data as well as the transfer to have
an error.
An example would be an input transfer from a bulk endpoint successfully
receiving 1 or more maxpacketsize packets from the device, followed
by a packet signalling halt.
While already touching all the devices and controllers handle_packet /
handle_data / handle_control code, also change the return type of
these functions to void, solely storing the status in the packet. To
make the code paths for regular versus async packet handling more
uniform.
This patch unfortunately is somewhat invasive, since makeing the qemu
usb core deal with this requires changes everywhere. This patch only
prepares the usb core for this, all the hcd / device changes are done
in such a way that there are no functional changes.
This patch has been tested with uhci and ehci hcds, together with usb-audio,
usb-hid and usb-storage devices, as well as with usb-redir redirection
with a wide variety of real devices.
Note that there is usually no need to directly set packet->actual_length
form devices handle_data callback, as that is done by usb_packet_copy()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Register displaychangelistener last, after spice is fully initialized,
otherwise we may hit NULL pointer dereferences when qemu starts calling
our callbacks.
Commit e250d949fe triggers this bug.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When entering vga mode the display size likely changes,
notify all displaychangelisteners about this.
Probably went unnoticed for a while as one if the first
things the guest does after leaving qxl native mode and
entering qxl vga mode is to set the vga video mode. But
there is still a small window where qemu can operate on
stale data, leading to crashes now and then.
https://bugzilla.redhat.com/show_bug.cgi?id=865767
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Due to usage of pixman for rendering on all spice surfaces we have
pixman's requirement that the stride be word aligned. A guest not
honoring that can crash spice and qemu with it due to failure to create
a surface (in spice-server). Avoid this early on in primary surface
creation and offscreen surface creation.
Recently windows guests got odd width support which triggers a non word
aligned primary surface in 16bit color depth. Off screen surfaces have
always been word aligned, but doesn't hurt to check them here too.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Postpone stopping the dirty log to the point where the command fifo is
configured to allow drivers which don't use the fifo to work too.
(Without this the picture rendered into the vram never got to the
screen and the DIRECT_VRAM option meant to support this case was
removed a year ago.)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
According to the documentation drivers using this device should read
FB_SIZE before enabling the device to know what memory to map. This
would not work if we return 0 before enabled. The docs also mention
reading SVGA_REG_DEPTH but not writing it. (Only SVGA_REG_BITS_PER_PIXEL
can be written but we don't really support that either.)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Removed info from vmsvga_state that is available from elsewhere and
thus was duplicated here unnecessarily.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* 'trivial-patches' of git://github.com/stefanha/qemu:
pc: Drop redundant test for ROM memory region
exec: make some functions static
target-ppc: make some functions static
ppc: add missing static
vnc: add missing static
vl.c: add missing static
target-sparc: make do_unaligned_access static
m68k: Return semihosting errno values correctly
cadence_uart: More debug information
Conflicts:
target-m68k/m68k-semi.c
Console cleanup series renamed dpy_resize and dpy_update all over the
tree, but hw/xenfb.c was forgotten. Update it too so it builds again.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* kraxel/usb.69: (31 commits)
usb-redir: Allow redirecting super speed devices to high speed controllers
usb-redir: Allow to attach USB 2.0 devices to 1.1 host controller
usb-redir: Use reject rather the disconnect on bad ep info
usb-redir: Add an usbredir_setup_usb_eps() helper function
usb-redir: Add support for input pipelining
usb-redir: Add support for 32 bits bulk packet length
combined-packet: Add a workaround for Linux usbfs + live migration
usb: Add packet combining functions
uhci: Don't crash on device disconnect
uhci: Add a uhci_handle_td_error() helper function
usb/ehci-pci: add helper to create ich9 usb controllers
usb/ehci-pci: add ich9 00:1a.* variant
usb/ehci-pci: dynamic type generation
uhci: add ich9 00:1a.* variants
uhci: stick irq routing info into UHCIInfo too.
uhci: dynamic type generation
xilinx_zynq: add USB controllers
usb/ehci: add sysbus variant
usb/ehci: split into multiple source files
usb/ehci: Guard definition of EHCI_DEBUG
...
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just a few lines above, we already initialize rom_memory accordingly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add more helpful debug information to the cadence UART.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* stefanha/net:
e1000: pre-initialize RAH/RAL registers
net: Reject non-netdevs in qmp_netdev_del()
net: use "socket" model name for UDP sockets
e1000: drop check_rxov, always treat RX ring with RDH == RDT as empty
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* qemu-kvm/uq/master: (28 commits)
update-linux-headers.sh: Handle new kernel uapi/ directories
target-i386: kvm_cpu_fill_host: use GET_SUPPORTED_CPUID
target-i386: cpu: make -cpu host/check/enforce code KVM-specific
target-i386: make cpu_x86_fill_host() void
Emulate qemu-kvms -no-kvm option
Issue warning when deprecated -tdf option is used
Issue warning when deprecated drive parameter boot=on|off is used
Use global properties to emulate -no-kvm-pit-reinjection
Issue warning when deprecated -no-kvm-pit is used
Use machine options to emulate -no-kvm-irqchip
cirrus_vga: allow configurable vram size
target-i386: Add missing kvm cpuid feature name
i386: cpu: add missing CPUID[EAX=7,ECX=0] flag names
i386: kvm: filter CPUID leaf 7 based on GET_SUPPORTED_CPUID, too
i386: kvm: reformat filter_features_for_kvm() code
i386: kvm: filter CPUID feature words earlier, on cpu.c
i386: kvm: mask cpuid_ext4_features bits earlier
i386: kvm: mask cpuid_kvm_features earlier
i386: kvm: x2apic is not supported without in-kernel irqchip
i386: kvm: set CPUID_EXT_TSC_DEADLINE_TIMER on kvm_arch_get_supported_cpuid()
...
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
To avoid continually having to bump the initrd load address
to account for larger kernel images, put the initrd halfway
through RAM. This allows large kernels on new boards with lots
of RAM to work OK, without breaking existing usecases for
boards with only 32MB of RAM.
Note that this change fixes in passing a bug where we were
passing an overly large max_size to load_image_targphys()
for the initrd, which meant that we wouldn't correctly refuse
to load an enormous initrd that didn't actually fit into RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Igor Mitsyanko <i.mitsyanko@samsung.com>
Tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* 'ppc-for-upstream' of git://repo.or.cz/qemu/agraf:
pseries: Cleanup duplications of ics_valid_irq() code
pseries: Clean up inconsistent variable name in xics.c
target-ppc: Extend FPU state for newer POWER CPUs
target-ppc: Rework storage of VPA registration state
Revert "PPC: pseries: Remove hack for PIO window"
* 'arm-devs.for-upstream' of git://git.linaro.org/people/pmaydell/qemu-arm: (28 commits)
hw/sd.c: add SD card save/load support
vmstate: Add support for saving/loading bitmaps
hw/sd.c: Fix erase for high capacity cards
pflash_cfi01: Fix debug mode printfery
pflash_cfi0x: QOMified
pflash_cfi01: remove unused total_len field
pflash_cfi0x: remove unused base field
hw/versatile_i2c: Use LOG_GUEST_ERROR
hw/arm_l2x0: Use LOG_GUEST_ERROR
hw/arm_sysctl: Use LOG_GUEST_ERROR
hw/armv7m_nvic: Use LOG_GUEST_ERROR and LOG_UNIMP
hw/arm_timer: Use LOG_GUEST_ERROR and LOG_UNIMP
hw/arm_gic: Use LOG_GUEST_ERROR
hw/arm11mpcore: Use LOG_GUEST_ERROR rather than hw_error()
hw/pl190: Use LOG_UNIMP rather than hw_error()
hw/pl110: Use LOG_GUEST_ERROR rather than hw_error()
hw/pl080: Use LOG_GUEST_ERROR and LOG_UNIMP
hw/pl061: Use LOG_GUEST_ERROR
hw/pl050: Use LOG_GUEST_ERROR
hw/exynos4_boards: Don't prematurely explode QEMUMachineInitArgs
...
This follows the logic of host-linux: If a 2.0 device has no ISO
endpoint and no interrupt endpoint with a packet size > 64, we can
attach it also to an 1.1 host controller. In case the redir server does
not report endpoint sizes, play safe and remove the 1.1 compatibility as
well. Moreover, if we detect a conflicting change in the configuration
after the device was already attached, it will be disconnected
immediately.
HdG: Several small cleanups and fixes
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
So that the client gets a notification about us disconnecting the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Older versions (anything but the latest) of Linux usbfs + libusb(x),
will submit larger (bulk) transfers split into multiple 16k submissions,
which means that rather then all tds getting linked into the queue in
one atomic operarion they get linked in a bunch at a time, which could
cause problems if:
1) We scan the queue while libusb is in the middle of submitting a split
bulk transfer
2) While this bulk transfer is pending we migrate to another host.
The problem is that after 2, the new host will rescan the queue and
combine the packets in one large transfer, where as 1) has caused the
original host to see them as 2 transfers. This patch fixes this by stopping
combinging if we detect a 16k transfer with its int_req flag set.
This should not adversely effect performance for other cases as:
1) Linux never sets the interrupt flag on packets other then the last
2) Windows does set the in_req flag on each td, but will submit large
transfers in 20k tds thus never triggering the check
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
