Once again, the emulation of the EERD and ICS registers in e1000.c is
incorrect. Nobody has noticed this before because none of the Intel-written
e1000 drivers use these registers, and all of the independently written open
source drivers copy Intel's example, so they don't use them either.
Regardless, these registers are documented in the programmer's manuals, and
their emulated behavior doesn't match the verified behavior of real hardware,
so any software that does use them doesn't function correctly.
-Bill
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When a VM state change handler changes VM state, other VM state change
handlers can see the state transitions out of order.
bmdma_map(), scsi_disk_init() and virtio_blk_init() install VM state
change handlers to restart DMA. These handlers can vm_stop() by
running into a write error on a drive with werror=stop. This throws
the VM state change handler callback into disarray. Here's an example
case I observed:
0. The virtual IDE drive goes south. All future writes return errors.
1. Something encounters a write error, and duly stops the VM with
vm_stop().
2. vm_stop() calls vm_state_notify(0).
3. vm_state_notify() runs the callbacks in list vm_change_state_head.
It contains ide_dma_restart_cb() installed by bmdma_map(). It also
contains audio_vm_change_state_handler() installed by audio_init().
4. audio_vm_change_state_handler() stops audio stuff.
5. User continues VM with monitor command "c". This runs vm_start().
6. vm_start() calls vm_state_notify(1).
7. vm_state_notify() runs the callbacks in vm_change_state_head.
8. ide_dma_restart_cb() happens to come first. It does its work, runs
into a write error, and duly stops the VM with vm_stop().
9. vm_stop() runs vm_state_notify(0).
10. vm_state_notify() runs the callbacks in vm_change_state_head.
11. audio_vm_change_state_handler() stops audio stuff. Which isn't
running.
12. vm_stop() finishes, ide_dma_restart_cb() finishes, step 7's
vm_state_notify() resumes running handlers.
13. audio_vm_change_state_handler() starts audio stuff. Oopsie.
Fix this by moving the actual write from each VM state change handler
into a new bottom half (suggested by Gleb Natapov).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These are now unused.
However, perhaps the idea is that when we add -device, they will be
useful? In that case, we should add virtio-net-pci-0-10 too.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have the pc-0.10 machine type now which does exactly the same
thing.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I don't think it's critical to do this, but it's
best to keep uninit and error recovery consistent.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Follow on patch will use it to determine the size of the MADT and
other BIOS tables.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch addresses the problems found by Andriy Gapon:
- The code was incorrectly overwriting the high order 32
bits of the timer and hpet config registers. This didn't show up
in testing because linux and windows use hpet in legacy mode,
where the high order 32 bits (advertising available interrupts)
of the timer config register are ignored, and the high order 32
bits of the hpet config register are reserved and unused.
- The mask for level-triggered interrupts was off by a bit. (hpet
doesn't currently support level-triggered interrupts).
In addition, I removed some unused #defines, and corrected the ioapic
interrupt values advertised. I'd set this up early in hpet development
and never went back to correct it, and no bugs resulted since linux and
windows use hpet in legacy mode where available interrupts are ignored.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Demo QemuOpts in action ;)
Implementing a alternative way to specify the filename should be
just a few lines of code now once we decided how the cmd line syntax
should look like.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
cleanup pretty simliar to the drives_table removal patch:
- drop the table and make a linked list out of it.
- pass around struct pointers instead of table indices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
First step cleaning up the drives handling. This one does nothing but
removing drives_table[], still it became seriously big.
drive_get_index() is gone and is replaced by drives_get() which hands
out DriveInfo pointers instead of a table index. This needs adaption in
*tons* of places all over.
The drives are now maintained as linked list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Hook i44fx pcihost into sysbus.
Convert Host bridge and ISA bridge pci devices to qdev.
Tag as no-user.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch implements a parser and qdev tree walker for bus paths and
adds qdev_device_add on top of this.
A bus path can be:
(1) full path, i.e. /i440FX-pcihost/pci.0/lsi/scsi.0
(2) bus name, i.e. "scsi.0". Best used together with id= to make
sure this is unique.
(3) relative path starting with a bus name, i.e. "pci.0/lsi/scsi.0"
For the (common) case of a single child bus being attached to a device
it is enougth to specify the device only, i.e. "pci.0/lsi" will be
accepted too.
qdev_device_add() adds devices and accepts bus= parameters to find the
bus the device should be attached to. Without bus= being specified it
takes the first bus it finds where the device can be attached to (i.e.
first pci bus for pci devices, ...).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Create a default bus name if none is passed to qbus_create().
If the parent device has DeviceState->id set it will be used to create
the bus name,. i.e. -device lsi,id=foo will give you a scsi bus named
"foo.0".
If there is no id BusInfo->name (lowercased) will be used instead, i.e.
-device lsi will give you a scsi bus named "scsi.0".
A scsi adapter with two scsi busses would have "scsi.0" and "scsi.1" or
"$id.0" and "$id.1" busses. The numbers of the child busses are per
device, i.e. when adding two lsi adapters both will have a "*.0" child
bus.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So we can parse "$slot.$fn" strings into devfn numbers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The pc-0.11 type allows users of qemu-0.11 to use a machine type which
they know will remain compatible when the upgrade to qemu-0.12.
Management tools may choose to canonicalize the 'pc' machine type to
'pc-0.11' so that if the 'pc' alias changes target in future versions
of qemu, the machine type used will remain compatible.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add an 'alias' field to QEMUMachine and display it in the output of
'qemu -M ?' with an '(aliased to foo)' suffix.
Aliases can change targets in newer versions of qemu, so management tools
may choose canonicalize machine types to ensure that if a user chooses an
alias, that the actual machine type used will remain compatible in
future.
This is intended to mimic a symlink to a machine description file.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
My self-built PPC kernel doesn't fit in the region reserved for
the kernel, so I can't use -kernel with it.
Let's just extend the region.
Signed-off-by: Alexander Graf <agraf@suse.de>
When giving KVM a slot of a size not on page boundary, it chokes. So let's
just round up the VGA BIOS size so nobody complains anymore and we don't need
to implement sub-page slots.
Required for booting a PPC guest in KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
This is a backport from qemu-kvm. Just instead of using kvm's specific
notification mechanism, we use qemu_notify_event()
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch requires "Handle BH's queued by AIO completions in
qemu_aio_flush()" to work reliably. The combination of those two
patches survived 300+ migrations with heavy IO load running in the
guest.
Signed-off-by: Nolan Leake <nolan <at> sigbus.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I used the following command to enable debugging:
perl -p -i -e 's/^\/\/#define DEBUG/#define DEBUG/g' * */* */*/*
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Hi!
Attached patch uses qemu_isxdigit() instead of isxdigit().
Fixes build warning on NetBSD.
Signed-off-by: Christoph Egger <Christoph.Egger@amd.com>
--
---to satisfy European Law for business letters:
Advanced Micro Devices GmbH
Karl-Hammerschmidt-Str. 34, 85609 Dornach b. Muenchen
Geschaeftsfuehrer: Thomas M. McCoy, Giuliano Meroni
Sitz: Dornach, Gemeinde Aschheim, Landkreis Muenchen
Registergericht Muenchen, HRB Nr. 43632
On some Sparc32 machines, fdc is located above 4G limit, so uint32_t is not
appropriate type for io_base.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The sequence of reading from eeprom is "offset by one" moved because of a false
detection of a clock cycle after an eeprom reset. Keeping the last clock value
after a reset keeps it in sync.
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add class property to virtio-console-pci allowing to specify the PCI class.
Add compat property to pc-0.10 to set the old PCI class.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add class property to virtio-blk-pci allowing to specify the PCI class.
Add compat property to pc-0.10 to set the old PCI class.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add id field to DeviceState. Make "info qtree" print it.
This helps users and management apps identifying devices in monitor
output, which is especially useful with otherwise identical devices
such as two virtio disks.
This patch doesn't add a way to set the id, followup patches will do.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
no_user: prevent users from adding certain devices.
desc: description of the device.
alias: to allow user friendly shortcuts on the command line, i.e.
-device usbmouse instead of -device "QEMU USB Mouse" or
-device lsi instead of -device lsi53c895a
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This add support for switching devices into a compatibility mode
using device properties. Machine types can have a list of properties
for specific devices attached to allow the easy creation of machine
types compatible to older qemu versions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently only common PS2 state is initialized, leaving keyboard and
mouse specific state to contain stale values.
Signed-off-by: Dinesh Subhraveti <dineshs@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Without this, after system reset, hpet does not detect transition from
non-legacy to legacy mode.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Here is a patch I had sent twice to the list 2 years ago.
Hopefuly this time someone will be interested
It adds support for passing vga mode to linux kernel through
vga= option in -append
Signed-off-by: Pascal Terjan <pterjan@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Disable the lengthy BIOS prompt for selecting a boot device by default,
but let the user reenable it via '-boot menu=on'.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Will be used by '-boot once=...', and should also help in other use
cases.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move registration function for the boot_set callback handler and provide
qemu_boot_set so that it can also be used outside the monitor code.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a pc-0-10 machine type to allow a pc machine to be created with
virtio block and console devices compatibility with qemu-0.10.x.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We're using PCI_CLASS_DISPLAY_OTHER now, but qemu-kvm.git is using
PCI_CLASS_OTHERS because:
"As a PCI_CLASS_DISPLAY_OTHER, it reduces primary display somehow on
Windows XP (possibly Windows disables acceleration since it fails
to find a driver)."
While this is valid, many versions of X will get confused by it.
Class major number of 0 gets treated as a possibly prehistoric VGA
device, and then the autoconfig logic gets confused trying to figure
out whether the virtio console or the pv vga device are the real VGA.
We should really set a proper class ID. 0x0780 (serial / other) seems
most appropriate. This shouldn't require any kernel changes, the
modalias for virtio looks like:
alias: pci:v00001AF4d*sv*sd*bc*sc*i*
so won't care what the base class or subclass are.
It shows up in the guest as:
00:05.0 Communication controller: Qumranet, Inc. Virtio console
A new qdev type is introduced to allow devices using the old class
to be created for compatibility with qemu-0.10.x.
Reported-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Windows virtio driver cannot pass DTM (certification) tests while the
storage class is PCI_CLASS_STORAGE_UNKNOWN.
A new qdev type is introduced to allow devices using the old class
to be created for compatibility with qemu-0.10.x.
Reported-by: Dor Laor <dlaor@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Use parameter 'next' to fix the hdecr case.
Also pass 'next' by value instead of pointer (more easy to read and no
performance issue for an always_inline function).
Signed-off-by: Tristan Gingold <gingold@adacore.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Allocate irq just before passing it to pci bridge initialization
and actually use it to initialize pci bridge.
Signed-off-by: igor.v.kovalenko@gmail.com
--
Kind regards,
Igor V. Kovalenko
For the sake of consistency. I pulled in the wrong patches from Gerd when
he did the qdev conversion.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Usage of msi vectors is controlled by the guest and so needs to be
restored on load. Do this for msi vectors used by the virtio device.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
MSIX present bit is tested incorrectly, and only happens to work because
the bit we are testing is 0x1. Add braces to fix this.
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Clean up msix vector usage state on load. Since guest might have control
over it through the device, the device will have to load this state from
file.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes a possible endianness issue in the usb-ohci hw module.
hcca.frame and ohci->frame_number are 16bit, so use cpu_to_le16().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
control vector is saved/restored by virtio-pci,
it does not belong in virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes segfault reported by Kevin Wolf,
and simplifies the code in msix_save.
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Otherwise if you hot remove an eepro100 NIC and then migrate,
you get:
Unknown savevm section or instance 'eeprom' 0
on the destination side.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
destroy_nic() requires that NICInfo::private by a PCIDevice pointer,
but then goes on to require that the same pointer matches
VLANClientState::opaque.
That is no longer the case for virtio-net since qdev and wasn't
previously the case for rtl8139, ne2k_pci or eepro100.
Make the situation a lot more clear by maintaining a VLANClientState
pointer in NICInfo.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* fix secondary bus setup.
* use base->name instead of "FIXME" for device name.
Yes, the device name is redundant. Only for drivers converted
to qdev already though. Once all drivers are converted we can
and should kill it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The only purpose DeviceType serves is creating a linked list of
DeviceInfo structs. This removes DeviceType and add a next field to
DeviceInfo instead, so the DeviceInfo structs can be changed that way.
Elimitates a pointless extra level of indirection.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
BusInfo is filled with name and size (pretty much like I did for
DeviceInfo as well). There is also a function pointer to print
bus-specific device information to the monitor. sysbus is hooked
up there, I've also added a print function for PCI.
Device creation is slightly modified as well: The device type search
loop now also checks the bus type while scanning the list instead of
complaining thereafter in case of a mismatch. This effectively gives
each bus a private namespace for device names.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paul Brook <paul@codesourcery.com>
Makes pci_qdev_register take a PCIDeviceInfo struct instead of a bunch
of parameters. Also adds config_read and config_write callbacks to
PCIDeviceInfo, so drivers needing these can be converted to the qdev
device API too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We want to do (at least) two things to the virtio-balloon device:
suppress it, and control its PCI address. Option -no-virtio-balloon
lets us do only the former. To get the latter, replace
-no-virtio-balloon with
-balloon none disable balloon device
-balloon virtio[,addr=str]
enable virtio balloon device (default)
Syntax suggested by Anthony Liguori.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
At this point, this refactoring looks like overkill. But we will need it
for CPU hotplugging, and qemu-kvm already carries it. Merging it early
would help qemu-kvm when rebasing against upstream.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
During startup and after reset we have to synchronize user space to the
in-kernel KVM state. Namely, we need to transfer the VCPU registers when
they change due to VCPU as well as APIC reset.
This patch refactors the required hooks so that kvm_init_vcpu registers
its own per-VCPU reset handler and adds a cpu_synchronize_state to the
APIC reset. That way we no longer depend on the new reset order (and can
drop this disliked interface again) and we can even drop a KVM hook in
main().
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The "pci_addr=" prefix currently required by pci_add/remove and
drive_add has no practical use. Drop it, but still silently accept it
for backward compatibility.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch implements support for Multiboot on x86 for -kernel.
Multiboot is a "new" approach to get rid of different bootloaders, providing
a unified interface for the kernel. It supports command line options and
kernel modules.
The two probably best known projects using multiboot are Xen and GNU Hurd.
This implementation should be mostly feature-complete. It is missing VBE
extensions, but as no system uses them currently it does not really hurt.
To use multiboot, specify the kernel as -kernel option. Modules should be given
as -initrd options, seperated by a comma (,). -append also works.
Please bear in mind that grub also does gzip decompression, which qemu does
not do yet. To run existing images, please ungzip them first.
The guest multiboot loader code is implemented as option rom using int 19.
Parts of the work are based on efforts by Rene Rebe, who originally ported
my code to int 19.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Multiboot passes options to the option rom using the fw_cfg device.
Right now, that device is local to the bochs_bios_init function.
Let's change that and expose it, so everyone may put data in there.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
For multiboot support, we need bochs_bios_init to happen before
load_linux, so we get the fw_cfg device.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce qemu_find_vlan_client_by_name for VLANClientState lookup based
on VLAN ID and client name. This is useful for monitor commands.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
[brought forward to current qemu-kvm.git]
This patch implements the missing qemu logic to
interpret a '-drive .. serial=XYZ ..' flag for
a virtio_blk device.
The serial number string is contained in a
skeletal IDENTIFY DEVICE data structure and
this structure is made available to the guest
virtio_blk driver via pci i/o region 0.
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add an option to specify the number of MSI-X vectors for PCI NIC cards. This
can also be used to disable MSI-X, for compatibility with old qemu. This
option currently only affects virtio cards.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Request up to 3 vectors in virtio-net. Actual bindings might supply
less.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add pci_get/set_byte to keep *_word and *_long access functions company.
They are unused for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement bindings for virtio save/load. Use them in virtio pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This enables actual support for MSI-X in virtio PCI.
First user will be virtio-net.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Extend virtio to support many interrupt vectors, and rearrange code in
preparation for multi-vector support (mostly move reset out to bindings,
because we will have to reset the vectors in transport-specific code).
Actual bindings in pci, and use in net, to follow.
Load and save are not connected to bindings yet, so they are left
stubbed out for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement MSI support in APIC. Note that MSI and MMIO APIC registers
are at the same memory location, but actually not on the global bus: MSI
is on PCI bus, APIC is connected directly to the CPU. We map them on the
global bus at the same address which happens to work because MSI
registers are reserved in APIC MMIO and vice versa.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add functions implementing MSI-X support. First user will be virtio-pci.
Note that platform must set a flag to declare MSI supported: this
is a safety measure to avoid breaking platforms which should support
MSI-X but currently lack this in the interrupt controller emulation.
For PC this will be set by APIC.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add "cmask" table of constant register masks: if a bit is not writeable
and is set in cmask table, this bit is checked on load. An attempt to
load an image that would change such a register causes load to fail.
Use this table to make sure that load does not modify registers that
guest can not change (directly or indirectly).
Note: we can't just assume that read-only registers never change,
because the guest could change a register indirectly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add routines to manage PCI capability list. First user will be MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add inline routines for convenient access to pci devices
with correct (little) endianness. Will be used by MSI-X support.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change much of hw/pci to use symbolic constants and a table-driven
design: add a mask table with writable bits set and readonly bits unset.
Detect change by comparing original and new registers.
This makes it easy to support capabilities where read-only/writeable
bit layout differs between devices, depending on capabilities present.
As a result, writing a single byte in BAR registers now works as
it should. Writing to upper limit registers in the bridge
also works as it should. Code is also shorter.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
APIC reset handler already resets cpu, no need to reset it twice.
Also register cpu_reset handler directly to make it impossible to
add additional code to main_cpu_reset() by mistake.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make drive_init() accept addr=, put the value into struct DriveInfo.
Use it in all the places that create virtio-blk-pci devices:
pc_init1(), bamboo_init(), mpc8544ds_init().
Don't support addr= in third argument of monitor command pci_add and
second argument of drive_add, because that clashes with their first
arguments. Admittedly unelegant.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Simply pass the PCI address through qemu_pci_hot_add_nic() to
pci_nic_init() and through qemu_pci_hot_add_storage() to pci_create().
Before, pci_device_hot_add() passed along the PCI bus to use, and
ignored any user-specified slot.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make net_client_init() accept addr=, put the value into struct
NICinfo. Use it in pci_nic_init(), and remove arguments bus and
devfn.
Don't support addr= in third argument of monitor command pci_add,
because that clashes with its first argument. Admittedly unelegant.
Machines "malta" and "r2d" have a default NIC with a well-known PCI
address. Deal with that the same way as the NIC model: make
pci_nic_init() take an optional default to be used when the user
doesn't specify one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
use NULL instead of 0 for pci_register_device() argument
for consistency. Any other caller uses NULL.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When virtio-net was merged in from qemu-kvm.git, the VNET_HDR related
features were dropped from the code.
However, VIRTIO_NET_F_MRG_RXBUF appears to have accidentally been
dropped too. Re-instate that now.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
introruce piix4_device_hot_add() for piix4 specific code
and make qemu_system_device_hot_add() generic.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This should fix compilation problem in case of CONFIG_USER_ONLY.
Currently INIT/SIPI is handled in the context of CPU that sends IPI.
This patch changes this to handle them like all other events in a main
cpu exec loop. When KVM will gain thread per vcpu capability it will
be much more clear to handle those event by cpu thread itself and not
modify one cpu's state from the context of the other.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Support a new feature flag for indirect ring entries. These are ring
entries which point to a table of buffer descriptors.
The idea here is to increase the ring capacity by allowing a larger
effective ring size whereby the ring size dictates the number of
requests that may be outstanding, rather than the size of those
requests.
This should be most effective in the case of block I/O where we can
potentially benefit by concurrently dispatching a large number of
large requests. Even in the simple case of single segment block
requests, this results in a threefold increase in ring capacity.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change the vring descriptor helpers to take the physical
address of the descriptor table rather than a virtqueue.
This is needed in order to allow these helpers to be used
with an indirect descriptor table.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The code how it is today, is totally painful to read and keep.
To begin with, the code is duplicated with the option rom loading
code that linux_boot and vga are already using.
This patch introduces a "bootable" state in NICInfo structure,
that we can use to keep track of whether or not a given nic should
be bootable, avoiding the introduction of yet another global state.
With that in hands, we move the code in vl.c to hw/pc.c, and use
the already existing infra structure to load those option roms.
Error checking code suggested by Mark McLoughlin
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also zero pci_irq_levels on reset to avoid stuck irq after reset.
Based on 15a1956af9 by Gleb Natapov.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Also zero pci_irq_levels on reset to avoid stuck irq after reset.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Yaniv Kamay <ykamay@redhat.com>
The device is not reset on system reset currently.
Without this patch RHEL4.8 hangs after reboot if -usbdevice table
is in use.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This reverts commit 3dcd219f09.
It is incorrect to call qemu_irq functions (or any other functions that
access other device state) during savevm/loadvm.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
vga_screen_dump_blank() was not generating a valid PPM file: the width of the
image made no sense (why it was multiplied by sizeof(uint32_t)?), and there was
only one sample per pixel, instead of three.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Section 10.8.25 ("START/STOP UNIT Command") of SFF-8020i states that
if the device is locked we should refuse to eject if the device is
locked.
ASC_MEDIA_REMOVAL_PREVENTED is the appropriate return in this case.
In order to stop itself from ejecting the media it is running from,
Fedora's installer (anaconda) requires the CDROMEJECT ioctl() to fail
if the drive has been previously locked.
See also https://bugzilla.redhat.com/501412
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This function is used to manage a PCI BAR, so make the more generic
pci_register_io_region() available to other uses.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
On reset:
Periodic Interrupt Enable (PIE) bit is cleared to zero
Alarm Interrupt Enable (AIE) bit is cleared to zero
Update ended Interrupt Flag (UF) bit is cleared to zero
Interrupt Request status Flag (IRQF) bit is cleared to zero
Periodic Interrupt Flag (PF) bit is cleared to zero
Alarm Interrupt Flag (AF) bit is cleared to zero
Square Wave output Enable (SQWE) zero
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Variable akitapda_machine is only used locally,
so the static attribute avoids a compiler warning.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
(patch is on top of "Apic creation should not depend on pci" series)
Currently cpu_index is used as cpu apic id on x86. This is incorrect
since apic ids not have to be continuous (they can also encode cpu
hierarchy information). This patch uses cpuid_apic_id for initial apic id
value. For now cpuid_apic_id is set to be equal to cpu_index so behaviour
is fully backward compatible, but it allows us to add qemu option to
provide other values for cpu apic id.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This new option may be used to disable the virtio-balloon device.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
SDL header files can be included in two different ways:
* like this: #include <SDL/SDL.h>
* like this: #include <SDL.h>
The 1st alternative is simple and works in many cases.
The 2nd alternative needs sdl-config to get the
correct compiler flags. It is the recommended way
to write SDL includes and standard for QEMU.
The patch fixes two non-standard SDL includes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Needed for savevm/loadvm + migration: In that case the queue might
already have packets on (re-)connect. The guest wouldn't notify us
because notifications are only sent when stuffing a packet into an
empty queue.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Rationale: move device information from code to data structures.
v2: Adapt the drivers missed in the first version.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* net-queue: (28 commits)
virtio-net: Increase filter and control limits
virtio-net: Add new RX filter controls
virtio-net: MAC filter optimization
virtio-net: Fix MAC filter overflow handling
virtio-net: reorganize receive_filter()
virtio-net: Use a byte to store RX mode flags
virtio-net: Add version_id 7 placeholder for vnet header support
virtio-net: implement rx packet queueing
net: make use of async packet sending API in tap client
net: add qemu_send_packet_async()
net: split out packet queueing and flushing into separate functions
net: return status from qemu_deliver_packet()
net: add return value to packet receive handler
net: pass VLANClientState* as first arg to receive handlers
net: re-name vc->fd_read() to vc->receive()
net: add fd_readv() handler to qemu_new_vlan_client() args
net: only read from tapfd when we can send
net: vlan clients with no fd_can_read() can always receive
net: move the tap buffer into TAPState
net: factor tap_read_packet() out of tap_send()
...
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Increase the size of the perfect filter table and control queue depth.
This should give us more headroom in the MAC filter and is known to be
needed by at least one guest user. Increasing the control queue depth
allows a guest to feed several commands back to back if they so desire
rather than using the send and wait approach Linux uses.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Add a few new RX modes to better control the receive_filter. These
are all fairly obvious features that hardware could provide.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
The MAC filter table is received from the guest as two separate
buffers, one with unicast entries, the other with multicast
entries. If we track the index dividing the two sets, we can
avoid searching the part of the table with the wrong type of
entries.
We could store this index as part of the save image, but its
trivially easy to discover it on load.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Overloading the promisc and allmulti flags for indicating filter
table overflow makes it difficult to track the actual requested
operating mode. Split these out into separate flags.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Reorganize receive_filter to better handle the split between
unicast and multicast filtering. This allows us to skip the
broadcast check on unicast packets and leads to more opportunities
for optimization.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
There's no need to save 4 bytes for promisc and allmulti.
Use one byte each just to avoid the overhead of a bitmap.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
If we don't have room to receive a packet, we return zero
from virtio_net_receive() and call qemu_flush_queued_packets()
as soon as space becomes available.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
VLANClientState's fd_read() handler doesn't read from file
descriptors, it adds a buffer to the client's receive queue.
Re-name the handlers to make things a little less confusing.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
This, apparently, is the style we prefer - all VLANClientState
should be an argument to qemu_new_vlan_client().
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
As host network devices can also be instantiated via the monitor, errors
should then be reported to the related monitor instead of stderr. This
requires larger refactoring, so this patch starts small with introducing
a helper to catch both cases and convert net_client_init as well as
net_slirp_redir.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Record device property types, and provide a list of properties at device
registration time.
Add a "device" property type that holds a reference to annother device.
Signed-off-by: Paul Brook <paul@codesourcery.com>
The ARMv7-M NVIC device pokes itself into the CPU state. Now we have a
proper device model we can have the CPU/SoC code do this.
Signed-off-by: Paul Brook <paul@codesourcery.com>
All,
I've recently been playing around with migration via exec. Unfortunately,
when starting the incoming qemu process with "-incoming exec:cmd", it suffers
the same problem that -incoming tcp used to suffer; namely, that you can't
interact with the monitor until after the migration has happened. This causes
problems for libvirt usage of -incoming exec, since libvirt expects to be able
to access the monitor ahead of time. This fairly simple patch allows you to
access the monitor both before and after the migration has completed using exec.
(note: developed/tested with qemu-kvm, but applies perfectly fine to qemu)
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When a reset is requested, the current e1000 emulation never clears the
reset bit which may cause a driver to hang. This patch masks the reset
bit out when setting the control registert, so the reset is immediately
completed.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This setup was designed by petalogix and is supported by upstream linux.
The design targets a xilinx spartan-3a-1800 dsp board with MMU.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
We have both IRQ sinks and GPIO inputs. These are in principle exactly
the same thing, so remove the former.
Signed-off-by: Paul Brook <paul@codesourcery.com>
"struct timeval last" caused a compilation error with mingw32
(missing header for struct timeval).
It is unused, so it was possible to remove it.
Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Implement and use a common device bus state. The main side-effect is
that creating a bus and attaching it to a parent device are no longer
separate operations. For legacy code we allow a NULL parent, but that
should go away eventually.
Also tweak creation code to veriry theat a device in on the right bus.
Signed-off-by: Paul Brook <paul@codesourcery.com>
After creating an automated regression test to test the sysrq
responses while running a linux image in qemu, I found that the
simulated uart was eating the character right after the sysrq about
75% of the time.
The problem is that the qemu sets the LSR_DR (data ready) bit on a
serial break. The automated tests can send a break and the sysrq
character quickly enough that the qemu serial fifo has a real
character available. When there is valid character in the fifo, it
gets consumed by the serial driver in the guest OS.
The real hardware also appears to set the LSR_DR but always appears to
have a null byte in this condition. This patch changes the qemu
behavior to match the tested characteristics of a real 16550 chip.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Implement the serial break via usb serial.
The second data byte in ftdi status packet contains the break status.
The values were already defined in usb-serial.c so it was a matter of
making use of the event_trigger to form a urb to send over to the host
controller with the serial break status set.
This was tested against a linux development image which enables sysrq
via a serial break on the ftdi usb console.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
kvm_physical_sync_dirty_bitmap() takes the end address as second
argument, not the region size. Moverover, the kvm API should not be used
directly here, but cpu_physical_sync_dirty_bitmap().
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch converts the current callers of qemu_fopen_ops().
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
f80f9ec changed the order that machines are registered which had the effect of
changing the default machine. This changeset introduces a new is_default field
so that machine types can declare that they are the default for an architecture.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
My previous commit, f92f8afebe, broke -vnc (spotted by Glauber Costa). This
is because it's necessary to tell when the no special display parameters have
been passed and default to SDL or VNC appropriately.
This refactors the display selection logic to be less complicated which has
the effect of fixing the regression mentioned above.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
initrd must be kept on the memory area below 4g. By not doing this,
we're seeing guests break while using -initrd and values of -mem
superior to 4096.
Signed-off-by: Glauber Costa <glommer@redhat.com>
The only target dependency for most hardware is sizeof(target_phys_addr_t).
Build these files into a convenience library, and use that instead of
building for every target.
Remove and poison various target specific macros to avoid bogus target
dependencies creeping back in.
Big/Little endian is not handled because devices should not know or care
about this to start with.
Signed-off-by: Paul Brook <paul@codesourcery.com>
If the target only has a 32-bit physical address space then
the code to map >4G ram breaks horribly, and causes compiler warnings.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Instead of exporting a custom structure to represent different
interrupt types, just export the irq array and have the top
elements point to the NMI lines.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Include assert.h from qemu-common.h and remove other direct uses.
cpu-all.h still need to include it because of the dyngen-exec.h hacks
Signed-off-by: Paul Brook <paul@codesourcery.com>
The vga_ram_size argument to machine init functions always has the same
value, and is ignored by many machines (including SPARC32 which has an
obsolete ifdef for VGA_RAM_SIZE).
Remove it and push VGA_RAM_SIZE into vga_int.h.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Now we can safely call AUD_init multiple times we can push it down to
individual audio devices, rather than having to pass it from the board
init.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Failure to initialize the audio subsystem is not handled consistently.
Where it is handled it has guest visible effects, which is wrong.
We already have a "nosound" audio driver as a last resort, so trying to
proceed without an audio backend seems pointless.
Also protect against multiple calls to AUD_init so that this can be
pushed down into individual devices.
Signed-off-by: Paul Brook <paul@codesourcery.com>
All VGA devices share a common field subset; currently they do so by
a macro which defines the common fields inline their state structures,
relying on the the common state being placed at offset 0 in the structure.
This makes refactoring the code difficult and requires a lot of error prone
casts.
Replace the macro by a new VGACommonState structure, and the casts by
regular field access and container_of() for upcasts.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_register_device already mallocs the pci config space buffer filled
with zeroes.
Doing this again breaks some default config space writes like
setting the subsystem vendor id and subsystem device id.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The linux loader is just an option rom like any other, just with
some special requirements. Right now, our option rom resetting
mechanism is not being applied to it. As a result, users using
-kernel will not be able to successfully reboot their machines
This patch fixes it by saving all the data we generated in
the load_linux() function, to be used later by the option rom
resetting mechanism.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently, boot options are not preserved across a system reset.
option roms can modify themselves, or can for instance restore the real
int 0x19 vector after they tried to boot from it.
To properly do that, we need a reset handler registered to deal with option
roms. This patch is based on current version on qemu-kvm.git
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Trivial build warning/fixes when the local DEBUG define is enabled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The pci_register_device() call in PCI nic initialization routines can
fail. Handle this failure and propagate a meaningful error message to
the user instead of generating a SEGV.
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to PnP specification, Appendix B, Option ROMs
that support DDIM (device driver initialization model) should
have their memory space writeable.
KVM deviates from us here, by removing the IO_MEM_ROM flag,
to allow for PCI option ROMs (they require DDIM). However,
there's absolutely no reason we can't do the same.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The inhdr is at the end of the S/G list, not the beginning.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Here is an updated hardware watchdog patch, which should fix
everything that was raised about the previous version ...
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
[had the qemu list address wrong the first time, reply to this message,
not the previous if you were on Cc]
Add support for SG_IO passthru (packet commands) to the virtio-blk
backend. Conceptually based on an older patch from Hannes Reinecke
but largely rewritten to match the code structure and layering in
virtio-blk.
Note that currently we issue the hose SG_IO synchronously. We could
easily switch to async I/O, but that would required either bloating
the VirtIOBlockReq by the size of struct sg_io_hdr or an additional
memory allocation for each SG_IO request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
page0 and friends are ram addresses; a smaller size will overflow and
cause a segfault or random corruption.
Change them to ram_addr_t.
Signed-off-by: Avi Kivity <avi@redhat.com>
