Instead require either mulu2_i32 or muluh_i32. The code in tcg-op.h
already supports looking for both. Previous incomplete conversion?
Signed-off-by: Richard Henderson <rth@twiddle.net>
Step two in the transition, adding the new ldst opcodes. Keep the old
opcodes around until all backends support the new opcodes.
Signed-off-by: Richard Henderson <rth@twiddle.net>
* 'tcg-next' of git://github.com/rth7680/qemu: (29 commits)
tcg-i386: Make use of zero-extended memory helper routines
tcg: Introduce zero and sign-extended versions of load helpers
exec: Split softmmu_defs.h
target: Include softmmu_exec.h where forgotten
exec: Rename USUFFIX to LSUFFIX
tcg-i386: Don't perform GETPC adjustment in TCG code
exec: Reorganize the GETRA/GETPC macros
configure: Allow x32 as a host
tcg-i386: Adjust tcg_out_tlb_load for x32
tcg-i386: Use intptr_t appropriately
tcg: Fix jit debug for x32
tcg: Use appropriate types in tcg_reg_alloc_call
tcg: Change tcg_out_ld/st offset to intptr_t
tcg: Change tcg_gen_exit_tb argument to uintptr_t
tcg: Use uintptr_t in TCGHelperInfo
tcg: Change relocation offsets to intptr_t
tcg: Change memory offsets to intptr_t
tcg: Change frame pointer offsets to intptr_t
tcg: Define TCG_ptr properly
tcg: Define TCG_TYPE_PTR properly
...
On MIPS ext8s and ext16s ops are implemented with a dedicated
instruction only on MIPS32R2, otherwise the same kind of implementation
than at TCG level (shift left followed by shift right) is used.
Change that by only implementing the ext8s and ext16s ops on MIPS32R2 so
that optimizations can be done by the optimizer. Use an inline version to
avoid having to test again for MIPS32R2 instructions. Keep the shift
implementation for the ld/st routines.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that TCG supports enabling and disabling ops at runtime, it's
possible to detect the available host instructions at runtime, and
enable the corresponding ops accordingly.
Unfortunately it's not easy to probe for available instructions on
MIPS, the information is partially available in /proc/cpuinfo, and
not available in AUXV. This patch therefore probes for the instructions
by trying to execute them and by catching a possible SIGILL signal.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With the optimization in tcg_liveness_analysis,
we can avoid the MFLO when it is unused.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use them in places where mulu2 and muls2 are used.
Optimize mulx2 with dead low part to mulxh.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
There are several hosts with only a "div" insn. Remainder is computed
manually from the quotient and inputs. We can do this generically.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
GUEST_BASE support is now supported by all TCG backends, and is
now mandatory. Drop the now-pointless TCG_TARGET_HAS_GUEST_BASE
define (set by every backend) and the error if it is unset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Fix the MIPS32(R2) cpu detection so that it also works with
-march=octeon. Thanks to Andrew Pinski for the hint.
Cc: Andrew Pinski <apinski@cavium.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
movcond operation can be implemented on MIPS32 Release 2 using the MOVN,
MOVZ, SLT and SLTU instructions.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
deposit operations can be optimized on MIPS32 Release 2 using the INS
instruction.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
rotr operations can be optimized on MIPS32 Release 2 using the ROTR and
ROTRV instructions. Also implemented rotl operations by subtracting the
shift from 32.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
bswap operations can be optimized on MIPS32 Release 2 using the ROTR,
WSBH and SEH instructions. We can't use the non-R2 code to implement the
ops due to registers constraints, so don't define the corresponding
TCG_TARGET_HAS_bswap* values.
Also bswap16* operations are supposed to be called with the 16 high bits
zeroed. This is the case everywhere (including for TCG by definition)
except when called from the store helper. Remove the AND instructions from
bswap16* and move it there.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implemented with setcond if the target does not provide
the optional opcode.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that CONFIG_TCG_PASS_AREG0 is enabled for all targets,
remove dead code and support for !CONFIG_TCG_PASS_AREG0 case.
Remove dyngen-exec.h and all references to it. Although included by
hw/spapr_hcall.c, it does not seem to use it.
Remove unused HELPER_CFLAGS.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The TCG targets i386 and tci needed a change of the function
prototype for w64.
This change is currently not needed for the other TCG targets,
but it can be applied to avoid code differences.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Most targets did not name the enum; tci used TCGRegister.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is now declared for all tcg targets in tcg.h,
so the tcg target specific declarations are redundant.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By always defining these symbols, we can eliminate a lot of ifdefs.
To allow this to be checked reliably, the semantics of the
TCG_TARGET_HAS_* macros must be changed from def/undef to true/false.
This allows even more ifdefs to be removed, converting them into
C if statements.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use the correct header in the TCG MIPS code to find cacheflush() on OpenBSD
to fix compilation of the MIPS host support for OpenBSD/mips64 based architecures.
Signed-off-by: Brad Smith <brad@comstyle.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Register fp (frame pointer) is a bad choice for compilations
without optimisation, because the compiler makes heavy use
of this register (so the resulting code crashes).
Register s0 had been used for TCG_AREG1 in earlier releases,
but was no longer used and is now free for TCG_AREG0.
The resulting code works for compilations without
optimisation (tested with qemu mips in qemu mips
on x86 host).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Based on a patch from Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
A few words about design choices:
* Two registers, at and t0, are reserved for TCG internal use. They are
useful for bswap and 64-bit ops.
* Most ops supports a constant argument with value 0, which is actually
mapped to the zero register.
* While the at register is available for constant loading, ops only
support a limited range of constants. TCG does a better job doing the
register allocation and constant loading by itself. There are plenty of
registers available anyway.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
