If a machine is started with ic-mode=xive but the guest only knows
about XICS, eg. an RHEL 7.6 guest, the kernel panics. This is
expected but a bit unfortunate since the crash doesn't provide
much information for the end user to guess what's happening.
Detect that during CAS and exit QEMU with a proper error message
instead, like it is already done for the MMU.
Even if this is less likely to happen, the opposite case of a guest
that only knows about XIVE would certainly fail all the same if the
machine is started with ic-mode=xics.
Also, the only valid values a guest can pass in byte 23 of OV5 during
CAS are 0b00 (XIVE legacy mode) and 0b01 (XIVE exploitation mode). Any
other value is a bug, at least with the current spec. Again, it does
not seem right to let the guest go on without a precise idea of the
interrupt mode it asked for.
Handle these cases as well.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155793986451.464434.12887933000007255549.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ibm,purr and ibm,spurr device tree properties are used to indicate
that the processor implements the Processor Utilisation of Resources
Register (PURR) and Scaled Processor Utilisation of Resources Registers
(SPURR), respectively. Each property has a single value which represents
the level of architecture supported. A value of 1 for ibm,purr means
support for the version of the PURR defined in book 3 in version 2.02 of
the architecture. A value of 1 for ibm,spurr means support for the
version of the SPURR defined in version 2.05 of the architecture.
Add these properties for all processors for which the PURR and SPURR
registers are generated.
Fixes: 0da6f3fef9 "spapr: Reorganize CPU dt generation code"
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190506014803.21299-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
AIX 5.1 expects the base year to be 1900. Adjust accordingly.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190505152839.18650-4-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The MC146818 RTC was incorrectly added to the i82378 chipset in
commit a04ff94097. In the next commit (506b7ddf88) the PReP
machine use the i82378.
Since the MC146818 is specific to the PReP machine, move its use
there.
Fixes: a04ff94097
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190505152839.18650-3-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190505152839.18650-2-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As explained in commit aff39be0ed97:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-2-philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Implement fw_cfg_arch_key_name(), which returns the name of a
ppc-specific key.
The fw_cfg device is used by the machine using OpenBIOS:
- 40p
- mac99 (oldworld)
- g3beige (newworld)
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190422195020.1494-6-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=RpAK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190426' into staging
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With MT-TCG, we are now running translation in a racy way, thus
we need to mimic hardware when it comes to updating the R and
C bits, by doing byte stores.
The current "store_hpte" abstraction is ill suited for this, we
replace it with two separate callbacks for setting R and C.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
LSI mapping in spapr currently open-codes standard PCI swizzling. It thus
duplicates the code of pci_swizzle_map_irq_fn().
Expose the swizzling formula so that it can be used with a slot number
when building the device tree. Simply drop pci_spapr_map_irq() and call
pci_swizzle_map_irq_fn() instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184841.8446.13959787238854054119.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the changelog of 298a971024, SpaprPhbState::dtbusname was
introduced to "make it easier to relate the guest and qemu views of memory
to each other", hence its name.
Use it when creating the PHB node to avoid code duplication.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184292.8446.8225650773162648595.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_ics_create() is only called once. Merge it in spapr_irq_init_xics()
and simplify a bit the error handling by using 'error_fatal' .
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190321144914.19934-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Removing RTAS handlers will become necessary when the new pseries
machine supporting multiple interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190321144914.19934-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 47973a2dbf we split the last generic chipset out of
the PC board, but missed to remove the i8042 keyboard controller.
This omission was later fixed in commit 7cb00357c1, but here we
forgot to remove the "i8042.h" include. Do it now.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316201528.9140-1-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVIDIA V100 GPUs have on-board RAM which is mapped into the host memory
space and accessible as normal RAM via an NVLink bus. The VFIO-PCI driver
implements special regions for such GPUs and emulates an NVLink bridge.
NVLink2-enabled POWER9 CPUs also provide address translation services
which includes an ATS shootdown (ATSD) register exported via the NVLink
bridge device.
This adds a quirk to VFIO to map the GPU memory and create an MR;
the new MR is stored in a PCI device as a QOM link. The sPAPR PCI uses
this to get the MR and map it to the system address space.
Another quirk does the same for ATSD.
This adds additional steps to sPAPR PHB setup:
1. Search for specific GPUs and NPUs, collect findings in
sPAPRPHBState::nvgpus, manage system address space mappings;
2. Add device-specific properties such as "ibm,npu", "ibm,gpu",
"memory-block", "link-speed" to advertise the NVLink2 function to
the guest;
3. Add "mmio-atsd" to vPHB to advertise the ATSD capability;
4. Add new memory blocks (with extra "linux,memory-usable" to prevent
the guest OS from accessing the new memory until it is onlined) and
npuphb# nodes representing an NPU unit for every vPHB as the GPU driver
uses it for link discovery.
This allocates space for GPU RAM and ATSD like we do for MMIOs by
adding 2 new parameters to the phb_placement() hook. Older machine types
set these to zero.
This puts new memory nodes in a separate NUMA node to as the GPU RAM
needs to be configured equally distant from any other node in the system.
Unlike the host setup which assigns numa ids from 255 downwards, this
adds new NUMA nodes after the user configures nodes or from 1 if none
were configured.
This adds requirement similar to EEH - one IOMMU group per vPHB.
The reason for this is that ATSD registers belong to a physical NPU
so they cannot invalidate translations on GPUs attached to another NPU.
It is guaranteed by the host platform as it does not mix NVLink bridges
or GPUs from different NPU in the same IOMMU group. If more than one
IOMMU group is detected on a vPHB, this disables ATSD support for that
vPHB and prints a warning.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for vfio portions]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190312082103.130561-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Rename qemu_getrampagesize() to qemu_minrampagesize(). While at it,
properly rename find_max_supported_pagesize() to
find_min_backend_pagesize().
s390x is actually interested into the maximum ram pagesize, so
introduce and use qemu_maxrampagesize().
Add a TODO, indicating that looking at any mapped memory backends is not
100% correct in some cases.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190417113143.5551-3-david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Recent commit 5cf0d326a0 fixed a regression which was preventing the
guest to access the extended config space of a PCIe device. This was
done by introducing a new PCI bus subtype for PAPR. The original fix
was causing PCI busses to be named "spapr-pci-host-bridge-root-bus.N"
instead of "pci.N", which was making upper layers unhappy of course.
This got worked around by hardcoding the PCI bus name to "pci.0", but
this only works for the default PHB. And we're now hitting:
# qemu-system-ppc64 \
-device spapr-pci-host-bridge,index=1 \
-device e1000e,bus=pci.0 \
-device e1000e,bus=pci.1
qemu-system-ppc64: -device e1000e,bus=pci.1: Bus 'pci.1' not found
David already posted some patches [1] to control PCI extended config
space accesses with a new flag in the base PCI bus class instead of
subtyping. These patches are a bit more intrusive though, and
are targetted for 4.1.
When no name is passed to pci_register_bus(), the core device code
generates a lowercase name based on the QOM typename. The typename
for the base PCI bus class is "PCI", hence the "pci.0", "pci.1"
bus names. Rename the type of the PAPR PCI bus to "pci", so that
the QOM code can generate proper names. This is a hack but it is
enough to fix the regression. And all this will be reworked properly
in 4.1.
[1] https://patchwork.ozlabs.org/project/qemu-devel/list/?series=100486
Fixes: 5cf0d326a0
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155500034416.646888.1307366522340665522.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PAPR PHB acts as a legacy PCI bus but it allows PCIe extended
config space accesses anyway (for pseries-2.9 and newer machine
types).
Introduce a specific PCI bus subtype to inform the common PCI code
about that.
Fixes: c2077e2ca0
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155414130834.574858.16502276132110219890.stgit@bahia.lan>
[dwg: Apply fix so we don't rename the default pci bus, breaking everything]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On non-P9 machines, the XIVE interrupt mode is not advertised, see
spapr_dt_ov5_platform_support(). Add a couple of checks on the machine
configuration to filter bogus setups and prevent OS failures :
Interrupt modes
CPU/Compat XICS XIVE dual
P8/P8 OK QEMU failure (1) OK (3)
P9/P8 OK QEMU failure (2) OK (3)
P9/P9 OK OK OK
(1) CPU exception model is incompatible with XIVE and the presenters
will fail to realize.
(2) CPU exception model is compatible with XIVE, but the XIVE CAS
advertisement is dropped when in POWER8 mode. So we could ended up
booting with the XIVE DT properties but without the HCALLs. Avoid
confusing Linux with such settings and fail under QEMU.
(3) force XICS in machine init
Remove the check on XIVE-only machines in spapr_machine_init(), which
has now become redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190328100044.11408-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
27461d69a0 "ppc: add host-serial and host-model machine attributes
(CVE-2019-8934)" introduced 'host-serial' and 'host-model' machine
properties for spapr to explicitly control the values advertised to the
guest in device tree properties with the same names.
The previous behaviour on KVM was to unconditionally populate the device
tree with the real host serial number and model, which leaks possibly
sensitive information about the host to the guest.
To maintain compatibility for old machine types, we allowed those props
to be set to "passthrough" to take the value from the host as before. Or
they could be set to "none" to explicitly omit the device tree items.
Special casing specific values on what's otherwise a user supplied string
is very ugly. So, this patch simplifies things by implementing the
backwards compatibility in a different way: we have a machine class flag
set for the older machines, and we only load the host values into the
device tree if A) they're not set by the user and B) we have that flag set.
This does mean that the "passthrough" functionality is no longer available
with the current machine type. That's ok though: if a user or management
layer really wants the information passed through they can read it
themselves (OpenStack Nova already does something similar for x86).
It also means the user can't explicitly ask for the values to be omitted
on the old machine types. I think that's an acceptable trade-off: if you
care enough about not leaking the host information you can either move to
the new machine type, or use a dummy value for the properties.
For the new machine type, this also removes an odd inconsistency
between running on a POWER and non-POWER (or non-Linux) hosts: if the
host information couldn't be read from where we expect (in the host's
device tree as exposed by Linux), we'd fallback to omitting the guest
device tree items.
While we're there, improve some poorly worded comments, and the help text
for the properties.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
We use PPC_SEGMENT_64B in various places to guard code that is specific
to 64-bit server processors compliant with arch 2.x. Consolidate the
logic in a helper macro with an explicit name.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155327783157.1283071.3747129891004927299.stgit@bahia.lan>
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When virtio-vga was added, the intention was to only support it for
those machines where the firmware does not know about virtio-gpu,
and supported VGA legacy hardware before virtio-{gpu,vga} were
introduced.
The Kconfig switch however enabled virtio-vga for all machines with
a PCI bus, and libvirt then prefers it even on hardware where
virtio-gpu would be preferrable. At least for now, only enable
virtio-vga for PC, hppa and pSeries machines, as was the case
before Kconfig dependencies were introduced.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes when configuring with CONFIG_PCI_DEVICES=n:
$ qemu-system-ppc64 -bios /dev/null -M bamboo
qemu-system-ppc64: Unsupported NIC model: e1000
Fixes: 7c28b925b7
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190316200818.8265-9-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is only needed through I82378, which also selects it.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PSI registers are 64-bit.
Spotted by Coverity: CID 1399704
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155248884690.893204.5428179144527749023.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Detected by Coverity: CID 1399702
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155248884129.893204.2293309859485638162.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
176dccee "target/ppc/spapr: Clear partition table entry when allocating
hash table" reworked the H_REGISTER_PROCESS_TABLE hypercall, but
unfortunately due to a small error no longer correctly sets the LPCR[GTSE]
bit which allows the guest to directly execute (some types of) tlbie (TLB
flush) instructions without involving the hypervisor.
We got away with this, initially, because POWER9 did not have hypervisor
mode enabled in its msr_mask, which meant we didn't actually run hypervisor
privilege checks in TCG at all. However, da874d90 "target/ppc: add HV
support for POWER9" turned on HV support on POWER9 for the benefit of the
powernv machine type.
This exposed the earlier bug in H_REGISTER_PROCESS_TABLE, and causes guests
which rely on LPCR[GTSE] (i.e. basically all of them) to crash during early
boot when their first tlbie instruction causes an unexpected trap.
Fixes: 176dccee target/ppc/spapr: Clear partition table entry when allocating hash table
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Cleber Rosa <crosa@redhat.com>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Activate only stop0 and stop1 levels. We should not need more levels
when under QEMU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To improve OPAL/skiboot support. We don't need to strictly model these
XSCOM accesses.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new class attribute to define XSCOM operations per CPU
family and add a couple of XSCOM addresses controlling the power
management states of the core on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV LPC Controller exposes different sets of registers for
each of the functional units it encompasses, among which the OPB
(On-Chip Peripheral Bus) Master and Arbitrer and the LPC HOST
Controller.
The mapping addresses of each register range are correct but the sizes
are too large. Fix the sizes and define the OPB Arbitrer range to fill
the gap between the OPB Master registers and the LPC HOST Controller
registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>