The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting directly into a kernel, bypassing the boot loader, the CPU and
UART clocks are not set up correctly. This makes the system appear very
slow, and causes the initrd boot test to fail when optimization is off.
The UART clock must run at 24 MHz. The default 25 MHz reference clock
cannot achieve this, so switch to PLL2/2 @ 480 MHz, which works
perfectly with the default /20 divider.
The CPU clock should run at 800 MHz, so switch it to PLL1/2. PLL1 runs
at 800 MHz by default, so we need to double the feedback divider as well
to make it run at 1600 MHz (so PLL1/2 runs at 800 MHz).
We don't bother checking for PLL lock because we know our emulated PLLs
lock instantly.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-13-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements a device model for the NPCM7xx SPI flash controller.
Direct reads and writes, and user-mode transactions have been tested in
various modes. Protection features are not implemented yet.
All the FIU instances are available in the SoC's address space,
regardless of whether or not they're connected to actual flash chips.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-11-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This just implements the bare minimum to cause the boot block to skip
memory initialization.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-10-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports reading and writing OTP fuses and keys. Only fuse reading
has been tested. Protection is not implemented.
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-9-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
