When emulating various SSE4.1 instructions such as pinsrd, the address
of a memory operand is computed without allowing for the 8-bit
immediate operand located after the memory operand, meaning that the
memory operand uses the wrong address in the case where it is
rip-relative. This patch adds the required rip_offset setting for
those instructions, so fixing some GCC test failures (13 in the gcc
testsuite in my GCC 6-based testing) when testing with a default CPU
setting enabling those instructions.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Message-Id: <alpine.DEB.2.20.1708080041391.28702@digraph.polyomino.org.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RDHWR CC reads the CPU timer like MFC0 CP0_Count, so with icount enabled
it must set can_do_io while it calls the helper to avoid the "Bad icount
read" error. It should also break out of the translation loop to ensure
that timer interrupts are immediately handled.
Fixes: 2e70f6efa8 ("Add instruction counter.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
DMTC0 CP0_Cause does a redundant gen_io_start() and gen_io_end() pair,
even though this is done for all DMTC0 operations outside of the switch
statement. Remove these redundant calls.
Fixes: 5dc5d9f055 ("mips: more fixes to the MIPS interrupt glue logic")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Commit e350d8ca3a ("target/mips: optimize indirect branches") made
indirect branches able to directly find the next TB and jump straight to
it without breaking out of translated code and going around the main
execution loop. This breaks the assumption in target/mips/translate.c
that BS_STOP is sufficient to cause pending interrupts to be handled,
since interrupts are only checked in the main loop.
Fix a few of these assumptions by using gen_save_pc to update the saved
PC and using BS_EXCP instead of BS_STOP:
- [D]MFC0 CP0_Count may trigger a timer interrupt which should be
immediately handled.
- [D]MTC0 CP0_Cause may trigger an interrupt (but in fact translation
was only even being stopped in the DMTC0 case).
- [D]MTC0 CP0_<any> when icount is used is assumed could potentially
cause interrupts.
- EI may trigger an interrupt which was pending. I specifically hit
this case when running KVM nested in mipsel-softmmu. A timer
interrupt while the 2nd guest was executing is caught by KVM which
switches back to the normal Linux exception base and re-enables
interrupts with EI. Since the above commit QEMU doesn't leave
translated code until the nested KVM has already restored the KVM
exception base and returned to the 2nd guest, at which point it is
too late to check for pending interrupts and it gets stuck in an
infinite loop of unhandled interrupts.
Something similar was needed for ARM in commit b29fd33db5
("target/arm: use DISAS_EXIT for eret handling").
Fixes: e350d8ca3a ("target/mips: optimize indirect branches")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Richard Henderson <rth@twiddle.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
PFN0 and PFN1 have to be masked out with PageMask_Mask.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[Yongbok Kim:
Added commit message]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
MIPS KVM trap & emulate guest kernels have a different segment layout
compared with traditional MIPS kernels, to allow both the user and
kernel code to run from the user address segment without repeatedly
trapping to KVM.
QEMU currently supports this layout only for KVM, but its sometimes
useful to be able to run these kernels in QEMU on a PC, so enable it for
TCG too.
This also paves the way for MIPS KVM VZ support (which uses the normal
virtual memory layout) by abstracting whether user mode kernel segments
are in use.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
[Yongbok Kim:
minor change]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Improve the segment definitions used by get_physical_address() to yield
target_ulong types, e.g. 0xffffffff80000000 instead of 0x80000000. This
is in preparation for enabling emulation of MIPS KVM T&E segments in TCG
MIPS targets, which unlike KVM could potentially have 64-bit
target_ulong. In such a case the offset guest KSEG0 address ends up at
e.g. 0x000000008xxxxxxx instead of 0xffffffff8xxxxxxx.
This also allows the casts to int32_t that force sign extension to be
removed, which removes any confusion due to relational comparison of
unsigned (target_ulong) and signed (int32_t) types.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Writing to the MIPS DESAVE register (and now the KScratch registers)
will stop translation, supposedly due to risk of execution mode
switches. However these registers are basically RW scratch registers
with no side effects so there is no risk of them triggering execution
mode changes.
Drop the bstate = BS_STOP for these registers for both mtc0 and dmtc0.
Fixes: 7a387fffce ("Add MIPS32R2 instructions, and generally straighten out the instruction decoding. This is also the first percent towards MIPS64 support.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
qemu call kvm_get_vcpu_events, and kernel return sipi_vector always
0, never valid when reporting to user space. But when qemu calls
kvm_put_vcpu_events will make sipi_vector in kernel be 0. This will
accidently modify sipi_vector when sipi_vector in kernel is not 0.
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Reviewed-by: Liu Yi <liu.yi24@zte.com.cn>
Message-Id: <1500047256-8911-1-git-send-email-peng.hao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The PMSAv7 region number register is migrated for R profile
cores using the cpreg scheme, but M profile doesn't use
cpregs, and so we weren't migrating the MPU_RNR register state
at all. Fix that by adding a migration subsection for the
M profile case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-6-git-send-email-peter.maydell@linaro.org
When the PMSAv7 implementation was originally added it was for R profile
CPUs only, and reset was handled using the cpreg .resetfn hooks.
Unfortunately for M profile cores this doesn't work, because they do
not register any cpregs. Move the reset handling into arm_cpu_reset(),
where it will work for both R profile and M profile cores.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-5-git-send-email-peter.maydell@linaro.org
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
For an M profile v7PMSA, the system space (0xe0000000 - 0xffffffff) can
never be executable, even if the guest tries to set the MPU registers
up that way. Enforce this restriction.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-3-git-send-email-peter.maydell@linaro.org
The M profile PMSAv7 specification says that if the address being looked
up is in the PPB region (0xe0000000 - 0xe00fffff) then we do not use
the MPU regions but always use the default memory map. Implement this
(we were previously behaving like an R profile PMSAv7, which does not
special case this).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-2-git-send-email-peter.maydell@linaro.org
Correct off-by-one bug in the PSMAv7 MPU tracing where it would print
a write access as "reading", an insn fetch as "writing", and a read
access as "execute".
Since we have an MMUAccessType enum now, we can make the code clearer
in the process by using that rather than the raw 0/1/2 values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1500906792-18010-1-git-send-email-peter.maydell@linaro.org
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Starting Qemu with "qemu-system-tricore -nographic -M tricore_testboard -S"
and entering "x 0" at the monitor prompt leads to Segmentation fault.
This happens because tricore_cpu_get_phys_page_debug() is not implemented
yet, this is a temporary workaround to avoid the crash.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The instruction is 4 bytes long.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170721125609.11117-2-david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When commit 0bacd8b304 ('i386: Don't set CPUClass::cpu_def on
"max" model') removed the CPUClass::cpu_def field, we kept using
the x86_cpu_load_def() helper directly in max_x86_cpu_initfn(),
emulating the previous behavior when CPUClass::cpu_def was set.
However, x86_cpu_load_def() is intended to help initialization of
CPU models from the builtin_x86_defs table, and does lots of
other steps that are not necessary for "max".
One of the things x86_cpu_load_def() do is to set the properties
listed at tcg_default_props/kvm_default_props. We must not do
that on the "max" CPU model, otherwise under KVM we will
incorrectly report all KVM features as always available, and the
"svm" feature as always unavailable. The latter caused the bug
reported at:
https://bugzilla.redhat.com/show_bug.cgi?id=1467599
("Unable to start domain: the CPU is incompatible with host CPU:
Host CPU does not provide required features: svm")
Replace x86_cpu_load_def() with simple object_property_set*()
calls. In addition to fixing the above bug, this makes the KVM
branch in max_x86_cpu_initfn() very similar to the existing TCG
branch.
For reference, the full list of steps performed by
x86_cpu_load_def() is:
* Setting min-level and min-xlevel. Already done by
max_x86_cpu_initfn().
* Setting family/model/stepping/model-id. Done by the code added
to max_x86_cpu_initfn() in this patch.
* Copying def->features. Wrong because "-cpu max" features need to
be calculated at realize time. This was not a problem in the
current code because host_cpudef.features was all zeroes.
* x86_cpu_apply_props() calls. This causes the bug above, and
shouldn't be done.
* Setting CPUID_EXT_HYPERVISOR. Not needed because it is already
reported by x86_cpu_get_supported_feature_word(), and because
"-cpu max" features need to be calculated at realize time.
* Setting CPU vendor to host CPU vendor if on KVM mode.
Redundant, because max_x86_cpu_initfn() already sets it to the
host CPU vendor.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170712162058.10538-5-ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Document cpu_x86_fill_model_id() and define CPUID_MODEL_ID_SZ to
help callers use the right buffer size.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170712162058.10538-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing code duplicated the logic in host_vendor_fms(), so
reuse the helper function instead.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170712162058.10538-3-ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When initiating a program check interruption by calling program_interrupt
the instruction length (ilen) of the current instruction is supplied as
the third parameter.
On s390x all the IO instructions are of instruction format S and their
ilen is 4. The calls to program_interrupt (introduced by commits
7b18aad543 ("s390: Add channel I/O instructions.", 2013-01-24) and
61bf0dcb2e ("s390x/ioinst: Add missing alignment checks for IO
instructions", 2013-06-21)) however use ilen == 2.
This is probably due to a confusion between ilen which specifies the
instruction length in bytes and ILC which does the same but in halfwords.
If kvm_enabled() this does not actually matter, because the ilen
parameter of program_interrupt is effectively unused.
Let's provide the correct ilen to program_interrupt.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: 7b18aad543 ("s390: Add channel I/O instructions.")
Fixes: 61bf0dcb2e ("s390x/ioinst: Add missing alignment checks for IO instructions")
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170724143452.55534-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Adding some CONFIG_TCG tests to be finally able to compile QEMU
on s390x also without TCG.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1500886370-14572-6-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
These functions can not be compiled with --disable-tcg. But since we
need the other functions from helper.c in the non-tcg build, we can also
not simply remove helper.c from the non-tcg builds. Thus the problematic
functions have to be moved into a separate new file instead that we
can later omit in the non-tcg builds.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1500886370-14572-5-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
misc_helper.c won't be compiled with --disable-tcg anymore, but we
still need the program_interrupt() function in that case. Move it
to interrupt.c instead, and refactor it to re-use the code from
trigger_pgm_exception() (for TCG) and enter_pgmcheck() (for KVM,
which now got renamed to kvm_s390_program_interrupt() for
clarity).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1500886370-14572-4-git-send-email-thuth@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
misc_helper.c won't be compiled with --disable-tcg anymore, but we
still need the diag helpers in KVM builds, too, so move the helper
functions to a separate file.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1500886370-14572-3-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
translate.c can not be compiled with --disable-tcg, but we need
the s390_cpu_dump_state() in KVM-only builds, too. So let's move
that function to helper.c instead, which will also be compiled
when --disable-tcg has been specified.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1500886370-14572-2-git-send-email-thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There are certain features that we put into base models, but that are
not relevant for the actual search. The most famous example are
MSA subfunctions that might be disabled on certain real hardware out
there.
While the kvm host model detection will usually detect the correct model
on such machines (as it will in the common case not pass features to check
for into s390_find_cpu_def()), baselining will fall back to a quite old
model just because some MSA subfunctions are missing.
Let's improve that by ignoring lack of these features while performing
the search for a base model.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170720123721.12366-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Using ordinary bitmap operations to set/test bits does not work properly
on architectures !s390x. Let's drop (test|set)_bit_inv and introduce
(test|set)_be_bit instead. These functions work on uint8_t array, not on
unsigned longs arrays and are for now only used in the context of
CPU features.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170720123721.12366-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We'll have to do the same for TCG, so let's just move it in there.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170720123721.12366-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Unused and broken, let's just get rid of it.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170720123721.12366-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The SIE_KSS feature will allow a guest to use KSS for a nested guest.
To create a nested guest the SIE_F2 facility is still necessary.
Since SIE_F2 is not part of the default model it does not make
a lot of sense to provide the SIE_KSS feature in the default model.
Let's also create a dependency check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Message-Id: <1500550051-7821-2-git-send-email-borntraeger@de.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Fix a TCG temporary leak in the new aarch64 rev16 handling.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make visit_type_null() take an @obj argument like its buddies. This
helps keep the next commit simple.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Changes:
* Add Enhanced Virtual Addressing (EVA) support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)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=qlJH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/yongbok/tags/mips-20170721' into staging
MIPS patches 2017-07-21
Changes:
* Add Enhanced Virtual Addressing (EVA) support
# gpg: Signature made Fri 21 Jul 2017 03:25:15 BST
# gpg: using RSA key 0x2238EB86D5F797C2
# gpg: Good signature from "Yongbok Kim <yongbok.kim@imgtec.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8600 4CF5 3415 A5D9 4CFA 2B5C 2238 EB86 D5F7 97C2
* remotes/yongbok/tags/mips-20170721:
target/mips: Enable CP0_EBase.WG on MIPS64 CPUs
target/mips: Add EVA support to P5600
target/mips: Implement segmentation control
target/mips: Add segmentation control registers
target/mips: Add an MMU mode for ERL
target/mips: Abstract mmu_idx from hflags
target/mips: Check memory permissions with mem_idx
target/mips: Decode microMIPS EVA load & store instructions
target/mips: Decode MIPS32 EVA load & store instructions
target/mips: Prepare loads/stores for EVA
target/mips: Add CP0_Ebase.WG (write gate) support
target/mips: Weaken TLB flush on UX,SX,KX,ASID changes
target/mips: Fix TLBWI shadow flush for EHINV,XI,RI
target/mips: Fix MIPS64 MFC0 UserLocal on BE host
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On NetBSD, where tolower() and toupper() are implemented using an
array lookup, the compiler warns if you pass a plain 'char'
to these functions:
gdbstub.c:914:13: warning: array subscript has type 'char'
This reflects the fact that toupper() and tolower() give
undefined behaviour if they are passed a value that isn't
a valid 'unsigned char' or EOF.
We have qemu_tolower() and qemu_toupper() to avoid this problem;
use them.
(The use in scsi-generic.c does not trigger the warning because
it passes a uint8_t; we switch it anyway, for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> for the s390 part.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1500568290-7966-1-git-send-email-peter.maydell@linaro.org
Enable the CP0_EBase.WG (write gate) on the I6400 and MIPS64R2-generic
CPUs. This allows 64-bit guests to run KVM itself, which uses
CP0_EBase.WG to point CP0_EBase at XKPhys.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Add the Enhanced Virtual Addressing (EVA) feature to the P5600 core
configuration, along with the related Segmentation Control (SC) feature
and writable CP0_EBase.WG bit.
This allows it to run Malta EVA kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Implement the optional segmentation control feature in the virtual to
physical address translation code.
The fixed legacy segment and xkphys handling is replaced with a dynamic
layout based on the segmentation control registers (which should be set
up even when the feature is not exposed to the guest).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
cosmetic changes]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The optional segmentation control registers CP0_SegCtl0, CP0_SegCtl1 &
CP0_SegCtl2 control the behaviour and required privilege of the legacy
virtual memory segments.
Add them to the CP0 interface so they can be read and written when
CP0_Config3.SC=1, and initialise them to describe the standard legacy
layout so they can be used in future patches regardless of whether they
are exposed to the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The segmentation control feature allows a legacy memory segment to
become unmapped uncached at error level (according to CP0_Status.ERL),
and in fact the user segment is already treated in this way by QEMU.
Add a new MMU mode for this state so that QEMU's mappings don't persist
between ERL=0 and ERL=1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
[yongbok.kim@imgtec.com:
cosmetic changes]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The MIPS mmu_idx is sometimes calculated from hflags without an env
pointer available as cpu_mmu_index() requires.
Create a common hflags_mmu_index() for the purpose of this calculation
which can operate on any hflags, not just with an env pointer, and
update cpu_mmu_index() itself and gen_intermediate_code() to use it.
Also update debug_post_eret() and helper_mtc0_status() to log the MMU
mode with the status change (SM, UM, or nothing for kernel mode) based
on cpu_mmu_index() rather than directly testing hflags.
This will also allow the logic to be more easily updated when a new MMU
mode is added.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
When performing virtual to physical address translation, check the
required privilege level based on the mem_idx rather than the mode in
the hflags. This will allow EVA loads & stores to operate safely only on
user memory from kernel mode.
For the cases where the mmu_idx doesn't need to be overridden
(mips_cpu_get_phys_page_debug() and cpu_mips_translate_address()), we
calculate the required mmu_idx using cpu_mmu_index(). Note that this
only tests the MIPS_HFLAG_KSU bits rather than MIPS_HFLAG_MODE, so we
don't test the debug mode hflag MIPS_HFLAG_DM any longer. This should be
fine as get_physical_address() only compares against MIPS_HFLAG_UM and
MIPS_HFLAG_SM, neither of which should get set by compute_hflags() when
MIPS_HFLAG_DM is set.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Implement decoding of microMIPS EVA load and store instruction groups in
the POOL31C pool. These use the same gen_ld(), gen_st(), gen_st_cond()
helpers as the MIPS32 decoding, passing the equivalent MIPS32 opcodes as
opc.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Implement decoding of MIPS32 EVA loads and stores. These access the user
address space from kernel mode when implemented, so for each instruction
we need to check that EVA is available from Config5.EVA & check for
sufficient COP0 privilege (with the new check_eva()), and then override
the mem_idx used for the operation.
Unfortunately some Loongson 2E instructions use overlapping encodings,
so we must be careful not to prevent those from being decoded when EVA
is absent.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
