This adds the documentation to describe what is supported for the
'microchip-icicle-kit' machine, and how to boot the machine in QEMU.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per SST25VF016B datasheet [1], SST flash requires a dummy byte after
the address bytes. Note only SPI mode is supported by SST flashes.
[1] http://ww1.microchip.com/downloads/en/devicedoc/s71271_04.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210306060152.7250-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current two-stage lookup detection in riscv_cpu_do_interrupt falls
short of its purpose, as all it checks is whether two-stage address
translation either via the hypervisor-load store instructions or the
MPRV feature would be allowed.
What we really need instead is whether two-stage address translation was
active when the exception was raised. However, in riscv_cpu_do_interrupt
we do not have the information to reliably detect this. Therefore, when
we raise a memory fault exception we have to record whether two-stage
address translation is active.
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210319141459.1196741-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The previous implementation was broken in many ways:
- Used mideleg instead of hideleg to mask accesses
- Used MIP_VSSIP instead of VS_MODE_INTERRUPTS to mask writes to vsie
- Did not shift between S bits and VS bits (VSEIP <-> SEIP, ...)
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210311094738.1376795-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current condition for the use of background registers only
considers the hypervisor load and store instructions,
but not accesses from M mode via MSTATUS_MPRV+MPV.
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210311103036.1401073-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210311094902.1377593-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
According to the specification the "field SPVP of hstatus controls the
privilege level of the access" for the hypervisor virtual-machine load
and store instructions HLV, HLVX and HSV.
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210311103005.1400718-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If PMP permission of any address has been changed by updating PMP entry,
flush all TLB pages to prevent from getting old permission.
Signed-off-by: Jim Shu <cwshu@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1613916082-19528-4-git-send-email-cwshu@andestech.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Like MMU translation, add qemu log of PMP permission checking for
debugging.
Signed-off-by: Jim Shu <cwshu@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1613916082-19528-3-git-send-email-cwshu@andestech.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, PMP permission checking of TLB page is bypassed if TLB hits
Fix it by propagating PMP permission to TLB page permission.
PMP permission checking also use MMU-style API to change TLB permission
and size.
Signed-off-by: Jim Shu <cwshu@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1613916082-19528-2-git-send-email-cwshu@andestech.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Not disabling the UART leads to QEMU overwriting the UART receive buffer with
the newest received byte. The rx_level variable is added to allow the use of
the existing OpenTitan driver libraries.
Signed-off-by: Alexander Wagner <alexander.wagner@ulal.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210309152130.13038-1-alexander.wagner@ulal.de
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
vs() should return -RISCV_EXCP_ILLEGAL_INST instead of -1 if rvv feature
is not enabled.
If -1 is returned, exception will be raised and cs->exception_index will
be set to the negative return value. The exception will then be treated
as an instruction access fault instead of illegal instruction fault.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210223065935.20208-1-frank.chang@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Coverity reported (CID 1450831) an array overrun in
gen_mxu_D16MAX_D16MIN():
1103 } else if (unlikely((XRb == 0) || (XRa == 0))) {
....
1112 if (opc == OPC_MXU_D16MAX) {
1113 tcg_gen_smax_i32(mxu_gpr[XRa - 1], t0, t1);
1114 } else {
1115 tcg_gen_smin_i32(mxu_gpr[XRa - 1], t0, t1);
1116 }
>>> Overrunning array "mxu_gpr" of 15 8-byte elements at element
index 4294967295 (byte offset 34359738367) using index "XRa - 1U"
(which evaluates to 4294967295).
This happens because the code is confused about which of XRa, XRb and
XRc is the output, and which are the inputs. XRa is the output, but
most of the conditions separating out different special cases are
written as if XRc is the output, with the result that we can end up
in the code path that assumes XRa is non-0 even when it is zero.
Fix the erroneous code, bringing it in to line with the structure
used in functions like gen_mxu_S32MAX_S32MIN() and
gen_mxu_Q8MAX_Q8MIN().
Fixes: CID 1450831
Fixes: bb84cbf385
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210316131353.4533-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Version: GnuPG v1
iQEcBAABAgAGBQJgWGTMAAoJEO8Ells5jWIRLUQIAJ6xxOKldqyo9n9N2vP+6O1J
lLSC0NT2d0ACptl/8o+KKlf9z2n7o/SKykLUXwCjgLeT2xTKhJ+p8tPOXJ4gns3D
U3GGc20gUkuGwNl0g2Rr2Yz4EJXlxx5Sl9LJz9quyx0Yp0SV8fYgQpj3mLgRye6T
hbVSDnQiSyo1iSx+Q/Qc6+Gr4a+sV4pExhrVP1n61JFCB95DUMNqjBsHv+urowHh
WCN9JbHuiZRHeIGIZujJxzMrh8jlP4pPFIrXvsdwHm/xJlVTgMXFvfIjfi3IrYWU
NbI0PluSfPbeAB8V+aPb9386K4UFpEEHJipIm+4HSVpVsAuoRVnEVoIWGubXfWo=
=9Tij
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 22 Mar 2021 09:35:08 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net/eth: Add an assert() and invert if() statement to simplify code
net/eth: Read ip6_ext_hdr_routing buffer before accessing it
net/eth: Check iovec has enough data earlier
net/eth: Check size earlier in _eth_get_rss_ex_dst_addr()
net/eth: Better describe _eth_get_rss_ex_dst_addr's offset argument
net/eth: Simplify _eth_get_rss_ex_dst_addr()
net/eth: Use correct in6_address offset in _eth_get_rss_ex_dst_addr()
net/colo-compare.c: Optimize removal of secondary packet
net/colo-compare.c: Fix memory leak for non-tcp packet
hw/net: virtio-net: Initialize nc->do_not_pad to true
net: Pad short frames to minimum size before sending from SLiRP/TAP
net: Add a 'do_not_pad" to NetClientState
net: eth: Add a helper to pad a short Ethernet frame
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To simplify the function body, invert the if() statement, returning
earlier.
Since we already checked there is enough data in the iovec buffer,
simply add an assert() call to consume the bytes_read variable.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We want to check fields from ip6_ext_hdr_routing structure
and if correct read the full in6_address. Let's directly check
if our iovec contains enough data for everything, else return
early.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The 'offset' argument represents the offset to the ip6_ext_hdr
header, rename it as 'ext_hdr_offset'.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The length field is already contained in the ip6_ext_hdr structure.
Check it direcly in eth_parse_ipv6_hdr() before calling
_eth_get_rss_ex_dst_addr(), which gets a bit simplified.
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The in6_address comes after the ip6_ext_hdr_routing header,
not after the ip6_ext_hdr one. Fix the offset.
Cc: qemu-stable@nongnu.org
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Fixes: eb700029c7 ("net_pkt: Extend packet abstraction as required by e1000e functionality")
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
g_queue_remove needs to look up the list entry first, but we
already have it as result and can remove it directly with
g_queue_delete_link.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Additional to removing the packet from the secondary queue,
we also need to free it.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
For virtio-net, there is no need to pad the Ethernet frame size to
60 bytes before sending to it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The minimum Ethernet frame length is 60 bytes. For short frames with
smaller length like ARP packets (only 42 bytes), on a real world NIC
it can choose either padding its length to the minimum required 60
bytes, or sending it out directly to the wire. Such behavior can be
hardcoded or controled by a register bit. Similarly on the receive
path, NICs can choose either dropping such short frames directly or
handing them over to software to handle.
On the other hand, for the network backends like SLiRP/TAP, they
don't expose a way to control the short frame behavior. As of today
they just send/receive data from/to the other end connected to them,
which means any sized packet is acceptable. So they can send and
receive short frames without any problem. It is observed that ARP
packets sent from SLiRP/TAP are 42 bytes, and SLiRP/TAP just send
these ARP packets to the other end which might be a NIC model that
does not allow short frames to pass through.
To provide better compatibility, for packets sent from QEMU network
backends like SLiRP/TAP, we change to pad short frames before sending
it out to the other end, if the other end does not forbid it via the
nc->do_not_pad flag. This ensures a backend as an Ethernet sender
does not violate the spec. But with this change, the behavior of
dropping short frames from SLiRP/TAP interfaces in the NIC model
cannot be emulated because it always receives a packet that is spec
complaint. The capability of sending short frames from NIC models is
still supported and short frames can still pass through SLiRP/TAP.
This commit should be able to fix the issue as reported with some
NIC models before, that ARP requests get dropped, preventing the
guest from becoming visible on the network. It was workarounded in
these NIC models on the receive path, that when a short frame is
received, it is padded up to 60 bytes.
The following 2 commits seem to be the one to workaround this issue
in e1000 and vmxenet3 before, and should probably be reverted.
commit 78aeb23ede ("e1000: Pad short frames to minimum size (60 bytes)")
commit 40a87c6c9b ("vmxnet3: Pad short frames to minimum size (60 bytes)")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds a flag in NetClientState, so that a net client can tell
its peer that the packets do not need to be padded to the minimum
size of an Ethernet frame (60 bytes) before sending to it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a helper to pad a short Ethernet frame to the minimum required
length, which can be used by backends' code.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
FreeBSD 12.1 has reached end of life. Use 12.2 instead so that FreeBSD's
project's packages will work. Update which timezone to pick. Work around a QEMU
bug that incorrectly raises an exception on a CRC32 instruction with the FPU
disabled. The qemu bug is described here:
https://www.mail-archive.com/qemu-devel@nongnu.org/msg784158.html
Signed-off-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20210307155654.993-2-imp@bsdimp.com>
[thuth: Disable gnutls to work-around a problem with libtasn1]
Signed-off-by: Thomas Huth <thuth@redhat.com>
sun is a macro on these systems, thus renaming the variables on the
client and server.
Signed-off-by: David Carlier <devnexen@gmail.com>
Message-Id: <CA+XhMqzHPG5ezqY-YxbA+tMoadA3VDFWBX8_LaLC5YsQOMrz+A@mail.gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
local directive make the configure fails on these systems.
Signed-off-by: David Carlier <devnexen@gmail.com>
Message-Id: <CA+XhMqy95D8X-QvBcEfL=a-Rkgy6aJtheskkqZwQkreru+T_Wg@mail.gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When building qemu with GCC 11, test-block-iothread produces the following
warning:
../tests/unit/test-block-iothread.c:148:11: error: ‘buf’ may be used
uninitialized [-Werror=maybe-uninitialized]
This is caused by buf[512] left uninitialized and passed to
bdrv_save_vmstate() that expects a const uint8_t *, so the compiler
assumes it will be read and expects the parameter to be initialized.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210319112218.49609-1-eesposit@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
With the recent move of the unit tests to tests/unit directory some
instructions under the "Unit tests" section became imprecise, which
are fixed by this change.
Fixes: da668aa15b ("tests: Move unit tests into a separate directory")
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-Id: <20210318174407.2299930-1-wainersm@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Policy "crash" calls abort() when deprecated input is received.
Bugs in integration tests may mask the error from policy "reject".
Provide a larger hammer: crash outright. Masking that seems unlikely.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-12-armbru@redhat.com>
This policy rejects deprecated input, and thus permits "testing the
future". Implement it for QMP command arguments: reject commands with
deprecated ones. Example: when QEMU is run with -compat
deprecated-input=reject, then
{"execute": "eject", "arguments": {"device": "cd"}}
fails like this
{"error": {"class": "GenericError", "desc": "Deprecated parameter 'device' disabled by policy"}}
When the deprecated parameter is removed, the error will change to
{"error": {"class": "GenericError", "desc": "Parameter 'device' is unexpected"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-11-armbru@redhat.com>
This policy rejects deprecated input, and thus permits "testing the
future". Implement it for QMP commands: make deprecated ones fail.
Example: when QEMU is run with -compat deprecated-input=reject, then
{"execute": "query-cpus"}
fails like this
{"error": {"class": "CommandNotFound", "desc": "Deprecated command query-cpus disabled by policy"}}
When the deprecated command is removed, the error will change to
{"error": {"class": "CommandNotFound", "desc": "The command query-cpus has not been found"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-10-armbru@redhat.com>
Without this stub, the next commit fails to link. I suspect the real
cause is 947e47448d "monitor: Use getter/setter functions for
cur_mon".
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-9-armbru@redhat.com>
This policy suppresses deprecated bits in output, and thus permits
"testing the future". Implement it for QMP command query-qmp-schema:
suppress information on deprecated commands, events and object type
members, i.e. anything that has the special feature flag "deprecated".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-8-armbru@redhat.com>
QMP commands return their response as a generated QAPI type, which the
monitor core converts to JSON via QObject.
query-qmp-schema's response is the generated introspection data. This
is a QLitObject since commit 7d0f982bfb "qapi: generate a literal
qobject for introspection", v2.12). Before, it was a string. Instead
of converting QLitObject / string -> QObject -> QAPI type
SchemaInfoList -> QObject -> JSON, we take a shortcut: the command is
'gen': false, so it can return the QObject instead of the QAPI type.
Slightly simpler and more efficient.
The next commit will filter the response for output policy, and this
is easier in the SchemaInfoList representation. Drop the shortcut.
This replaces the manual command registration by a generated one. The
manual registration makes the command available before the machine is
built by passing flag QCO_ALLOW_PRECONFIG. To keep it available
there, we need need to add 'allow-preconfig': true to its definition
in the schema.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-7-armbru@redhat.com>
This policy suppresses deprecated bits in output, and thus permits
"testing the future". Implement it for QMP event data: suppress
deprecated members.
No QMP event data is deprecated right now.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-6-armbru@redhat.com>
This policy suppresses deprecated bits in output, and thus permits
"testing the future". Implement it for QMP events: suppress
deprecated ones.
No QMP event is deprecated right now.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-5-armbru@redhat.com>
This policy suppresses deprecated bits in output, and thus permits
"testing the future". Implement it for QMP command results. Example:
when QEMU is run with -compat deprecated-output=hide, then
{"execute": "query-cpus-fast"}
yields
{"return": [{"thread-id": 9805, "props": {"core-id": 0, "thread-id": 0, "socket-id": 0}, "qom-path": "/machine/unattached/device[0]", "cpu-index": 0, "target": "x86_64"}]}
instead of
{"return": [{"arch": "x86", "thread-id": 22436, "props": {"core-id": 0, "thread-id": 0, "socket-id": 0}, "qom-path": "/machine/unattached/device[0]", "cpu-index": 0, "target": "x86_64"}]}
Note the suppression of deprecated member "arch".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-4-armbru@redhat.com>
