Similar to the SMBus io registers there is a power management io range
that is set via similar base address reg and enable bit. Some handling
of this was already there but with several problems: using the wrong
registers and bits, wrong size range, not acually updating mapping and
handling reset correctly, nor emulating any of the actual io
registers. Some of these errors are fixed up here.
After this patch we use the correct base address register, enable bit
and region size and allow guests to map/unmap this region, but we
still don't emulate any of the registers in this range.
PMD notes regarding the Configuration Space Power Management Registers:
- 0x40 General Configuration 0
- 0x41 General Configuration 1
. Bit 7: I/O Enable for ACPI I/O Base
- 0x48 Power Mgmt I/O Base
. Bit 0: Always set
. Bits 7-15: Power Management I/O Register Base Address
(this explains the change 0xffc0 -> 0xff80)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 4/4, added notes]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reset the registers in the DeviceReset() handler which is called
on each device reset, not in DeviceRealize() which is called once.
Bit 0 of 'Power Mgmt I/O Base' register (offset 0x48) is always set.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch, this is part 3/4 (move to reset), document]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Section "Offset 4B-48 – Power Management I/O Base" describes:
Port Address for the base of the 128-byte Power
Management I/O Register block.
Correct the vt82c686-pm I/O region size.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 2/4, reduced size to 128B]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Previously just an empty RAM region was mapped on realize, now we add
an empty io range logging access instead. I think the pm timer should
be hooked up here but not sure guests need it. PMON on fuloong2e sets
a base address but does not seem to enable region; the pegasos2
firmware pokes some regs but continues anyway so don't know if
anything would make use of these facilities. Therefore this is just a
clean up of previous state for now and not intending to fully
implement missing functionality which could be done later if some
guests need it.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cff9b2442d3e2e1cfbdcbc2dfbb559031b4b1cc1.1610223397.git.balaton@eik.bme.hu>
[PMD: Split original patch, this is part 1/4
(make 'vt82c686-pm' an I/O tracing region)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The base address of the SMBus io ports and its enabled status is set
by registers in the PCI config space but this was not correctly
emulated. Instead the SMBus registers were mapped on realize to the
base address set by a property to the address expected by fuloong2e
firmware.
Fix the base and config register handling to more closely model
hardware which allows to remove the property and allows the guest to
control this mapping. Do all this in reset instead of realize so it's
correctly updated on reset.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <f2ca2ad5f08ba8cee07afd9d67b4e75cda21db09.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move lines around so that object definitions become consecutive and
not scattered around. This brings functions belonging to an object
together so it's clearer what is defined and what parts belong to
which object.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <9f942989dba46fc1c23b881f6cb135948f818c2f.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The superio memory region holds the io space index/data registers used
to access the superio config registers that are implemented in struct
SuperIOConfig. To keep these related things together move the memory
region to SuperIOConfig and rename it accordingly.
Also remove the unused "data" member of SuperIOConfig which is not
needed as we store actual data values in the regs array.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <dc3c4e7632716ca73c10506bd02ee93b39c28705.1610223397.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We have handy functions to access GPR. Use gen_store_gpr() for
Move From HI/LO Register and gen_load_gpr() for Move To opcodes.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210214175912.732946-8-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210214175912.732946-7-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
TCG displays the upper halve registers with the same name
as their lower halves. Rename the upper halves with the
'[hi]' suffix.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210214175912.732946-6-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The cpu::mmr[] array contains the upper halves of 128-bit GPR
registers. While they are only used by the R5900 CPU, the
concept is generic and could be used by another MIPS implementation.
Rename 'cpu::mmr' as 'cpu::gpr_hi' and make them global.
When the code is similar to the GPR lower halves, move it
close by.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210214175912.732946-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We will access the cpu_HI/LO registers outside of translate.c.
Make them publicly accessible.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210214175912.732946-4-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Commit 83be6b5412 ("Fix MSA instructions LD.<B|H|W|D> on big endian
host") introduced use of typedef/prototypes declared in "tcg/tcg.h"
without including it. This was not a problem because "tcg/tcg.h" is
pulled in by "exec/cpu_ldst.h". To be able to remove this header
there, we first need to include it here in op_helper.c, else we get:
[222/337] Compiling C object libqemu-mips-softmmu.fa.p/target_mips_msa_helper.c.o
target/mips/msa_helper.c: In function ‘helper_msa_ld_b’:
target/mips/msa_helper.c:8214:9: error: unknown type name ‘TCGMemOpIdx’
8214 | TCGMemOpIdx oi = make_memop_idx(MO_TE | DF | MO_UNALN, \
| ^~~~~~~~~~~
target/mips/msa_helper.c:8224:5: note: in expansion of macro ‘MEMOP_IDX’
8224 | MEMOP_IDX(DF_BYTE)
| ^~~~~~~~~
target/mips/msa_helper.c:8214:26: error: implicit declaration of function ‘make_memop_idx’ [-Werror=implicit-function-declaration]
8214 | TCGMemOpIdx oi = make_memop_idx(MO_TE | DF | MO_UNALN, \
| ^~~~~~~~~~~~~~
target/mips/msa_helper.c:8227:18: error: implicit declaration of function ‘helper_ret_ldub_mmu’ [-Werror=implicit-function-declaration]
8227 | pwd->b[0] = helper_ret_ldub_mmu(env, addr + (0 << DF_BYTE), oi, GETPC());
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210207232310.2505283-4-f4bug@amsat.org>
As the 'rw' argument is unused, remove it.
Reported-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210220202026.2305667-1-f4bug@amsat.org>
get_seg_physical_address() calls CPUMIPSTLBContext::map_address()
handlers passing a MMUAccessType type. Update the prototype
handlers to take a MMUAccessType argument, as it is stricter than
an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-14-f4bug@amsat.org>
get_physical_address() calls get_seg_physical_address() and
get_segctl_physical_address() passing a MMUAccessType type.
Let the prototypes use it as argument, as it is stricter than
an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-13-f4bug@amsat.org>
All these functions:
- mips_cpu_get_phys_page_debug()
- cpu_mips_translate_address()
- mips_cpu_tlb_fill()
- page_table_walk_refill()
- walk_directory()
call get_physical_address() passing a MMUAccessType type. Let the
prototype use it as argument, as it is stricter than an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-12-f4bug@amsat.org>
Both mips_cpu_tlb_fill() and cpu_mips_translate_address() pass
MMUAccessType to raise_mmu_exception(). Let the prototype use it
as argument, as it is stricter than an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-11-f4bug@amsat.org>
The single caller, do_translate_address(), passes MMUAccessType
to cpu_mips_translate_address(). Let the prototype use it as
argument, as it is stricter than an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-10-f4bug@amsat.org>
The single caller, HELPER_LD_ATOMIC(), passes MMUAccessType to
do_translate_address(). Let the prototype use it as argument,
as it is stricter than an integer.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-9-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-7-f4bug@amsat.org>
Remove these confusing and unused definitions.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-6-f4bug@amsat.org>
get_physical_address() doesn't use the 'access_type' argument,
remove it to simplify.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-5-f4bug@amsat.org>
get_segctl_physical_address() doesn't use the 'access_type' argument,
remove it to simplify.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-4-f4bug@amsat.org>
get_seg_physical_address() doesn't use the 'access_type' argument,
remove it to simplify.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-3-f4bug@amsat.org>
TLB map_address() handlers don't use the 'access_type' argument,
remove it to simplify.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20210128144125.3696119-2-f4bug@amsat.org>
Similarly to commits ae82adc8e29..7f93879e444, use the
translator_ld*() API introduced in commit 409c1a0bf0
to fetch the code on the MIPS target.
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210125105818.2707067-1-f4bug@amsat.org>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Translate embedded assembly into IO writes which is more
readable.
Also hardcode cm_base at boot time instead of reading from CP0.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-5-jiaxun.yang@flygoat.com>
[PMD: Kept code comments]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here boston)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace embedded binary with generated code.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201215064507.30148-2-jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Split original patch as one for each machine (here fuloong2e)]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the loongson3 defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210122122404.11970-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmAxAc0SHGxhdXJlbnRA
dml2aWVyLmV1AAoJEPMMOL0/L748FmsQAJWZ+WEGVpVqfL5SzNQaZEgrmAULUwvB
sXWmtM33jtdiNfn+3MsMNSh+KgJWadzvtrH/2K1vL7jPBoesfizrF5a7obwfy6cR
EDrUGrPuShr78UBFDreoxwAWfVG5sWNjilkirIavuuB9UsrfnSfeH5Us6gpY7WtW
CisXazLJ5g5avWtCpQ7uowSvuU44IrWgfdNISKG3ZnUD5Zj3SDCXL5nRIB97uj4I
xQxQ9LVdxn4eZ6hLxgciW4jqrQ3pQQmJDSLCtxQXSzuH6NAibdCzADkuyBIkQJdj
K56r1hDKEN48LZtSriCt3kJSbeM07JF53DIGuX48jY4HOEBWWH810MWJ6QMvPqmR
K9AUZNSY5tnfRJAL9Doy9fU7/VJG+OfO5y18UOB50OQcNN8lFnTbEEoFVdh9TACY
pi7dJPKuCi5eKQWgBMhu26Zf03Shq8SVbWZaigF3+QRS4cfkKimSX/1Mguyes8va
TryY3WVL9IcVQYE9S8nIdfTUJEKgDg8i8PmKAYa8aUj9c6X843wqur08chANTlB/
nyPIQaXJe3wldaK87pgoPk8NeaCaSAWBndpC+bXn0rDHcn585VX1VdGbekBi+hYM
6nYQEJhWHjImQmiowvF7x9Qe/obPpu5vyfreRWnXTPWZATHGxw8l9qfT23Xz/k2o
KrEkuf8ibR3n
=ipHI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging
Pull request trivial patches 20210220
# gpg: Signature made Sat 20 Feb 2021 12:34:21 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.0-pull-request:
MAINTAINERS: Fix default-configs/ entries
target/avr/cpu: Use device_class_set_parent_realize()
hw/scsi/megasas: Remove pointless parenthesis
u2f-passthru: put it into the 'misc' category
tpm: put some tpm devices into the correct category
nvdimm: put it into the 'storage' category
vmmouse: put it into the 'input' category
virtio-pmem: put it into the 'storage' category
MAINTAINERS: add my github tree URL
Fix SPDX-License-Identifier typos
hw/block/fdc: Remove the check_media_rate property
hw/i386/xen: Remove dead code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change generated automatically using the Coccinelle
patch included in commit bf85388169 ("qdev: use
device_class_set_parent_realize/unrealize/reset()")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210201080348.438095-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the u2f-passthru device is not set, put it into the 'misc'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20201130083630.2520597-10-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some tpm devices have no category, put them into the correct category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20201130083630.2520597-8-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the nvdimm device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-5-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the vmmouse device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-4-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The category of the virtio-pmem device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Message-Id: <20201130083630.2520597-3-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
I already used this github URL for PRs before and will continue to use it in
foreseeable future.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <E1l5rYG-0005sv-87@lizzy.crudebyte.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several SPDX headers contain "SPDX-License-Identifer" (note the
missing "i" before "er"); fix these typos.
Signed-off-by: Ryan Finnie <ryan@finnie.org>
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210201200147.211914-1-ryan@finnie.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This was only required for the pc-1.0 and earlier machine types.
Now that these have been removed, we can also drop the corresponding
code from the FDC device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20210203171832.483176-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'drivers_blacklisted' is never accessed, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210202155644.998812-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There is new interest in the SD/MMC device emulation, so it
would be good to have more than only one maintainer / reviewer
for it.
Bin Meng proved by his contributions a deep understanding of the
SD cards internals, so let's add him to the corresponding section
in the MAINTAINERS file.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210216132841.1121653-1-f4bug@amsat.org>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>