Add CP0_Config3 and CP0_Config5 to DisasContext structure. This is
needed for implementing availability control of various instructions.
Reviewed-by: "Aleksandar Markovic <amarkovic@wavecomp.com>"
Signed-off-by: "Aleksandar Markovic <amarkovic@wavecomp.com>"
Add emulation of various nanoMIPS load and store instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Implement emulation of nanoMIPS EXTW instruction. EXTW instruction
is similar to the MIPS r6 ALIGN instruction, except that it counts
the other way and in bits instead of bytes. We therefore generalise
gen_align() function into a new gen_align_bits() function (which
counts in bits instead of bytes and optimises when bits = size of
the word), and implement gen_align() and a new gen_ext() based on
that. Since we need to know the word size to check for when the
number of bits == the word size, the opc argument is replaced with
a wordsz argument (either 32 or 64).
Signed-off-by: James Hogan <james.hogan@mips.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Added a helper for ROTX based on the pseudocode from the
architecture spec. This instraction was not present in previous
MIPS instruction sets.
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add emulation of nanoMIPS instructions situated in pool p_lsx, and
emulation of LSA instruction as well.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of misc nanoMIPS instructions situated in pool32axf.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of nanoMIPS instructions that are situated in pool32a0.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of basic floating point arithmetic for nanoMIPS.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of LI48, ADDIU48, ADDIUGP48, ADDIUPC48, LWPC48, and
SWPC48 instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of nanoMIPS instructions MOVE.P and MOVE.PREV.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of SIGRIE, SYSCALL, BREAK, SDBBP, ADDIU, ADDIUPC,
ADDIUGP.W, LWGP, SWGP, ORI, XORI, ANDI, and other instructions.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of SAVE16 and RESTORE.JRC16 instructions. Routines
gen_save(), gen_restore(), and gen_adjust_sp() are provided to support
this feature.
This patch at the same time provides function gen_op_addr_addi(). This
function will be used in emulation of some other nanoMIPS instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of NOT16, AND16, XOR16, OR16 instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of misc nanoMIPS 16-bit instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of nanoMIPS 16-bit shift instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of nanoMIPS 16-bit branch instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add emulation of nanoMIPS 16-bit arithmetic instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add some basic utility functions and macros for nanoMIPS decoding
engine.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add empty body and invocation of decode_nanomips_opc() if the bit
ISA_NANOMIPS32 is set in ctx->insn_flags.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Only if Config3.ISA is 3 (microMIPS), the mode should be switched in
cpu_state_reset(). Config3.ISA is 1 for nanoMIPS processors, and no mode
change should happen.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Add nanoMIPS opcodes for DSP ASE instruction pools and instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add nanoMIPS opcodes. nanoMIPS instruction are organized by so-called
instruction pools. Each pool contains a set of opcodes, that in turn
can be instruction opcodes or instruction pool opcodes.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
Add ISA_NANOMIPS32 and CPU_NANOMIPS32 preprocessor constants.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Stefan Markovic <smarkovic@wavecomp.com>
-----BEGIN PGP SIGNATURE-----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=2bke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/check/20180822' into staging
check/next for 20180822
# gpg: Signature made Wed 22 Aug 2018 09:03:40 BST
# gpg: using RSA key F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/check/20180822:
check: Only test tpm devices when they are compiled in
check: Only test usb-ehci when it is compiled in
check: Only test usb-uhci devices when they are compiled in
check: Only test usb-ohci when it is compiled in
check: Only test nvme when it is compiled in
check: Only test pvpanic when it is compiled in
check: Only test wdt_ib700 when it is compiled in
check: Only test sdhci when it is compiled in
check: Only test i82801b11 when it is compiled in
check: Only test ioh3420 when it is compiled in
check: Only test ipack when it is compiled in
check: Only test hda when it is compiled in
check: Only test ac97 when it is compiled in
check: Only test es1370 when it is compiled in
check: Only test rtl8139 when it is compiled in
check: Only test pcnet when it is compiled in
check: Only test eepro100 when it is compiled in
check: Only test ne2000 when it is compiled in
check: Only test vmxnet3 when it is compiled in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix rounding errors in scaling float-to-int and int-to-float operations
* Connect virtualization-related IRQs and memory regions of GICv2
in boards that use Cortex-A7 or Cortex-A15
* Support taking exceptions to AArch32 Hyp mode
* Clear CPSR.IL and CPSR.J on 32-bit exception entry
(a minor bug fix that won't affect non-buggy guest code)
* mps2-an505: Implement various missing devices:
dual timer, watchdogs, counters in the FPGAIO registers,
some missing ID/control registers, TrustZone Master Security
Controllers, PL081 DMA controllers, PL022 SPI controllers
* correct ID register values for mps2-an385, -an511, -an505
* fix some hardcoded tabs in untouched backwaters of the
target/arm codebase
* raspi: Refactor framebuffer property handling code and implement
support for the virtual framebuffer/viewport
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4kLg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180824-1' into staging
target-arm queue:
* Fix rounding errors in scaling float-to-int and int-to-float operations
* Connect virtualization-related IRQs and memory regions of GICv2
in boards that use Cortex-A7 or Cortex-A15
* Support taking exceptions to AArch32 Hyp mode
* Clear CPSR.IL and CPSR.J on 32-bit exception entry
(a minor bug fix that won't affect non-buggy guest code)
* mps2-an505: Implement various missing devices:
dual timer, watchdogs, counters in the FPGAIO registers,
some missing ID/control registers, TrustZone Master Security
Controllers, PL081 DMA controllers, PL022 SPI controllers
* correct ID register values for mps2-an385, -an511, -an505
* fix some hardcoded tabs in untouched backwaters of the
target/arm codebase
* raspi: Refactor framebuffer property handling code and implement
support for the virtual framebuffer/viewport
# gpg: Signature made Fri 24 Aug 2018 13:19:04 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180824-1: (52 commits)
hw/arm/mps2: Fix ID register errors on AN511 and AN385
hw/display/bcm2835_fb: Validate bcm2835_fb_mbox_push() config
hw/display/bcm2835_fb: Validate config settings
hw/display/bcm2835_fb: Fix handling of virtual framebuffer
hw/display/bcm2835_fb: Abstract out calculation of pitch, size
hw/display/bcm2835_fb: Reset resolution, etc correctly
hw/display/bcm2835_fb: Drop unused size and pitch fields
hw/misc/bcm2835_property: Track fb settings using BCM2835FBConfig
hw/misc/bcm2835_fb: Move config fields to their own struct
target/arm: Remove a handful of stray tabs
target/arm: Untabify iwmmxt_helper.c
target/arm: Untabify translate.c
hw/arm/mps2-tz: Fix MPS2 SCC config register values
hw/arm/mps2-tz: Instantiate SPI controllers
hw/ssi/pl022: Correct wrong DMACR and ICR handling
hw/ssi/pl022: Correct wrong value for PL022_INT_RT
hw/ssi/pl022: Use DeviceState::realize rather than SysBusDevice::init
hw/ssi/pl022: Don't directly call vmstate_register()
hw/ssi/pl022: Set up reset function in class init
hw/ssi/pl022: Allow use as embedded-struct device
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix MPS2 SCC config register values for the mps2-an511
and mps2-an385 boards:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be the board number in hex, not decimal
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180823175225.22612-1-peter.maydell@linaro.org
Refactor bcm2835_fb_mbox_push() to work by calling
bcm2835_fb_validate_config() and bcm2835_fb_reconfigure(),
so that config set this way is also validated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-9-peter.maydell@linaro.org
Validate the config settings that the guest tries to set.
The wiki page documentation is not really accurate here:
generally rather than failing requests to set bad parameters,
the hardware will just clip them to something sensible.
Validate the most important parameters: sizes and
the viewport offsets. This prevents the framebuffer
code from trying to read out-of-range memory.
In the property handling code, we validate the new parameters every
time we encounter a tag that sets them. This means we validate the
config multiple times if the request includes multiple config-setting
tags, but the code would require significant restructuring to do a
validation only once but still return the clipped settings for
get-parameter tags and the buffer allocation tag.
Validation of settings made via the older bcm2835_fb_mbox_push()
function will be done in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-8-peter.maydell@linaro.org
The raspi framebuffir in bcm2835_fb supports the definition
of a virtual "viewport", which is smaller than the full
physical framebuffer size and at an adjustable offset within
it. Only the viewport area is sent to the screen. This allows
the guest to do things like double buffering, or scrolling
by adjusting the viewport origin. Currently QEMU doesn't
implement this at all.
Add support for this feature:
* the property mailbox code needs to distinguish the
virtual width/height from the physical width/height
* the framebuffer code needs to do something with the
virtual width/height/origin information
Note that the wiki documentation on the semantics of the
virtual and physical height and width has it the wrong way
around -- the virtual size is the size of the allocated
buffer, and the physical size is the size of the display,
so the virtual size is always the same as or larger than
the physical.
If the viewport size is set smaller than the physical
screen size, we ignore the viewport settings completely
and just display the physical screen area.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-7-peter.maydell@linaro.org
Abstract out the calculation of the pitch and size of the
framebuffer into functions that operate on the BCM2835FBConfig
struct -- these are about to get a little more complicated
when we add support for virtual and physical sizes differing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-6-peter.maydell@linaro.org
The bcm2835_fb's initial resolution and other parameters are set
via QOM properties. We should reset to those initial values on
device reset, which means we need to save the QOM property
values somewhere that they are not overwritten by guest
changes to the framebuffer configuration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-5-peter.maydell@linaro.org
The BCM2835FBState struct has a 'pitch' field which is a
cached copy of xres * (bpp >> 3), and a 'size' field which is
a cached copy of pitch * yres. However we don't actually do
anything with these fields; delete them. We retain the
now-unused slots in the VMState struct for migration
compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-4-peter.maydell@linaro.org
Refactor the fb property setting code so that rather than
using a set of pointers to local variables to track
whether a config value has been updated in the current
mbox and if so what its new value is, we just copy
all the current settings of the fb at the start, and
then update that copy as we go along, before asking
the fb to switch to it at the end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-3-peter.maydell@linaro.org
The handling of framebuffer properties in the bcm2835_property code
is a bit clumsy, because for each of the many fb related properties
we try to track the value we're about to set and whether we're going
to be setting a value, and then we hand all the new values off
to the framebuffer via a function which takes them all as separate
arguments. It would be simpler if the property code could easily
copy all the framebuffer's current settings, update them with
the new specified values and then ask the framebuffer to switch
to the new set.
As the first part of this refactoring, pull all the fb config
settings fields in BCM2835FBState out into their own struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814144436.679-2-peter.maydell@linaro.org
Following the bulk conversion of the iwMMXt code, there are
just a handful of hard coded tabs in target/arm; fix them.
This is a whitespace-only patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180821165215.29069-4-peter.maydell@linaro.org
Untabify the arm iwmmxt_helper.c. This affects only the iwMMXt code.
We've never touched that code in years, so it's not going to get
fixed up by our "change when touched" process, and a bulk change is
not going to be too disruptive.
This commit was produced using Emacs "untabify" (plus one
by-hand removal of a space to fix a checkpatch nit); it is
a whitespace-only change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180821165215.29069-3-peter.maydell@linaro.org
Untabify the arm translate.c. This affects only some lines,
mostly comments, in the iwMMXt code. We've never touched
that code in years, so it's not going to get fixed up
by our "change when touched" process, and a bulk change
is not going to be too disruptive.
This commit was produced using Emacs "untabify"; it is
a whitespace-only change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180821165215.29069-2-peter.maydell@linaro.org
Some of the config register values we were setting for the MPS2 SCC
weren't correct:
* the SCC_AID bits [23:20] specify the FPGA build target board revision,
and the SCC_CFG4 register specifies the actual board revision, so
these should have matching values. Claim to be board revision C,
consistently -- we had the revision in the wrong part of SCC_AID.
* SCC_ID bits [15:4] should be 0x505, not decimal 505
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-23-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The SPI controllers in the MPS2 AN505 board are PL022s.
We have a model of the PL022, so create these devices.
We don't currently model the LCD controller that sits behind
one of the PL022s; the others are intended to control devices
that sit on the FPGA's general purpose SPI connector or
"shield" expansion connectors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-22-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In the PL022, register offset 0x20 is the ICR, a write-only
interrupt-clear register. Register offset 0x24 is DMACR, the DMA
control register. We were incorrectly implementing (a stub version
of) DMACR at 0x20, and not implementing anything at 0x24. Fix this
bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-21-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL022 interrupt registers have bits allocated as:
0: ROR (receive overrun)
1: RT (receive timeout)
2: RX (receive FIFO half full or less)
3: TX (transmit FIFO half full or less)
A cut and paste error meant we had the wrong value for
the PL022_INT_RT constant. This bug doesn't affect device
behaviour, because we don't implement the receive timeout
feature and so never set that interrupt bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-20-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move from the legacy SysBusDevice::init method to using
DeviceState::realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-19-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Use the DeviceState vmsd pointer rather than calling vmstate_register()
directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-18-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the PL022 calls pl022_reset() from its class init
function. Make it register a DeviceState reset method instead,
so that we reset the device on system reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-17-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl022's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
While we're adding the new file to MAINTAINERS, add
also the .c file, which was missing an entry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-16-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The AN505 FPGA image includes four PL081 DMA controllers, each
of which is gated by a Master Security Controller that allows
the guest to prevent a non-secure DMA controller from accessing
memory that is used by secure guest code. Create and wire
up these devices.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-15-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit doesn't have any MSCs itself but it does need
some wiring to connect the external signals from MSCs
in the outer board model up to the registers and the
NVIC IRQ line.
We also need to expose a MemoryRegion corresponding to
the AHB bus, so that MSCs in the outer board model can
use that as their downstream port. (In the FPGA this is
the "AHB Slave Expansion" ports shown in the block
diagram in the AN505 documentation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-14-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IoTKit does not have any Master Security Contollers itself,
but it does provide registers in the secure privilege control
block which allow control of MSCs in the external system.
Add support for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-13-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>