Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 'uart-out' clock from the CPRMAN to the PL011 instance.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Those reset values have been extracted from a Raspberry Pi 3 model B
v1.2, using the 2020-08-20 version of raspios. The dump was done using
the debugfs interface of the CPRMAN driver in Linux (under
'/sys/kernel/debug/clk'). Each exposed clock tree stage (PLLs, channels
and muxes) can be observed by reading the 'regdump' file (e.g.
'plla/regdump').
Those values are set by the Raspberry Pi firmware at boot time (Linux
expects them to be set when it boots up).
Some stages are not exposed by the Linux driver (e.g. the PLL B). For
those, the reset values are unknown and left to 0 which implies a
disabled output.
Once booted in QEMU, the final clock tree is very similar to the one
visible on real hardware. The differences come from some unimplemented
devices for which the driver simply disable the corresponding clock.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This simple mux sits between the PLL channels and the DSI0E and DSI0P
clock muxes. This mux selects between PLLA-DSI0 and PLLD-DSI0 channel
and outputs the selected signal to source number 4 of DSI0E/P clock
muxes. It is controlled by the cm_dsi0hsck register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A clock mux can be configured to select one of its 10 sources through
the CM_CTL register. It also embeds yet another clock divider, composed
of an integer part and a fractional part. The number of bits of each
part is mux dependent.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The clock multiplexers are the last clock stage in the CPRMAN. Each mux
outputs one clock signal that goes out of the CPRMAN to the SoC
peripherals.
Each mux has at most 10 sources. The sources 0 to 3 are common to all
muxes. They are:
0. ground (no clock signal)
1. the main oscillator (xosc)
2. "test debug 0" clock
3. "test debug 1" clock
Test debug 0 and 1 are actual clock muxes that can be used as sources to
other muxes (for debug purpose).
Sources 4 to 9 are mux specific and can be unpopulated (grounded). Those
sources are fed by the PLL channels outputs.
One corner case exists for DSI0E and DSI0P muxes. They have their source
number 4 connected to an intermediate multiplexer that can select
between PLLA-DSI0 and PLLD-DSI0 channel. This multiplexer is called
DSI0HSCK and is not a clock mux as such. It is really a simple mux from
the hardware point of view (see https://elinux.org/The_Undocumented_Pi).
This mux is not implemented in this commit.
Note that there is some muxes for which sources are unknown (because of
a lack of documentation). For those cases all the sources are connected
to ground in this implementation.
Each clock mux output is exported by the CPRMAN at the qdev level,
adding the suffix '-out' to the mux name to form the output clock name.
(E.g. the 'uart' mux sees its output exported as 'uart-out' at the
CPRMAN level.)
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A PLL channel is able to further divide the generated PLL frequency.
The divider is given in the CTRL_A2W register. Some channels have an
additional fixed divider which is always applied to the signal.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PLLs are composed of multiple channels. Each channel outputs one clock
signal. They are modeled as one device taking the PLL generated clock as
input, and outputting a new clock.
A channel shares the CM register with its parent PLL, and has its own
A2W_CTRL register. A write to the CM register will trigger an update of
the PLL and all its channels, while a write to an A2W_CTRL channel
register will update the required channel only.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN PLLs generate a clock based on a prescaler, a multiplier and
a divider. The prescaler doubles the parent (xosc) frequency, then the
multiplier/divider are applied. The multiplier has an integer and a
fractional part.
This commit also implements the CPRMAN CM_LOCK register. This register
reports which PLL is currently locked. We consider a PLL has being
locked as soon as it is enabled (on real hardware, there is a delay
after turning a PLL on, for it to stabilize).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 5 PLLs in the CPRMAN, namely PLL A, C, D, H and B. All of them
take the xosc clock as input and produce a new clock.
This commit adds a skeleton implementation for the PLLs as sub-devices
of the CPRMAN. The PLLs are instantiated and connected internally to the
main oscillator.
Each PLL has 6 registers : CM, A2W_CTRL, A2W_ANA[0,1,2,3], A2W_FRAC. A
write to any of them triggers a call to the (not yet implemented)
pll_update function.
If the main oscillator changes frequency, an update is also triggered.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN (clock controller) was mapped at the watchdog/power manager
address. It was also split into two unimplemented peripherals (CM and
A2W) but this is really the same one, as shown by this extract of the
Raspberry Pi 3 Linux device tree:
watchdog@7e100000 {
compatible = "brcm,bcm2835-pm\0brcm,bcm2835-pm-wdt";
[...]
reg = <0x7e100000 0x114 0x7e00a000 0x24>;
[...]
};
[...]
cprman@7e101000 {
compatible = "brcm,bcm2835-cprman";
[...]
reg = <0x7e101000 0x2000>;
[...]
};
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nanosecond unit greatly limits the dynamic range we can display in
clock value traces, for values in the order of 1GHz and more. The
internal representation can go way beyond this value and it is quite
common for today's clocks to be within those ranges.
For example, a frequency between 500MHz+ and 1GHz will be displayed as
1ns. Beyond 1GHz, it will show up as 0ns.
Replace nanosecond periods traces with frequencies in the Hz unit
to have more dynamic range in the trace output.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use of 0x%d - make up our mind as 0x%x
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201014193355.53074-1-dgilbert@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi 3A+ is a stripped down version of the 3B:
- 512 MiB of RAM instead of 1 GiB
- no on-board ethernet chipset
Add it as it is a closer match to what we model.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Similarly to the Pi A, the Pi Zero uses a BCM2835 SoC (ARMv6Z core).
The only difference between the revision 1.2 and 1.3 is the latter
exposes a CSI camera connector. As we do not implement the Unicam
peripheral, there is no point in exposing a camera connector :)
Therefore we choose to model the 1.2 revision.
Example booting the machine using content from [*]:
$ qemu-system-arm -M raspi0 -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-zero.dtb \
-append 'printk.time=0 earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Zero
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi A is almost the first machine released.
It uses a BCM2835 SoC which includes a ARMv6Z core.
Example booting the machine using content from [*]
(we use the device tree from the B model):
$ qemu-system-arm -M raspi1ap -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-b-plus.dtb \
-append 'earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Model B+
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The realize() function is clearly composed of two parts,
each described by a comment:
void realize()
{
/* common peripherals from bcm2835 */
...
/* bcm2836 interrupt controller (and mailboxes, etc.) */
...
}
Split the two part, so we can reuse the common part with other
SoCs from this family.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It makes no sense to set enabled-cpus=0 on single core SoCs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 has only one core. Introduce the core_count field to
be able to use values different than BCM283X_NCPUS (4).
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove usage of TypeInfo::class_data. Instead fill the fields in
the corresponding class_init().
So far all children use the same values for almost all fields,
but we are going to add the BCM2711/BCM2838 SoC for the raspi4
machine which use different fields.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No code out of bcm2836.c uses (or requires) the BCM283XInfo
declarations. Move it locally to the C source file.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure the vSMMUv3 will be restored before all PCIe devices so that DMA
translation can work properly during migration.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20201019091508.197-1-yuzenghui@huawei.com
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows us to reuse npcm7xx_timer_pause for the watchdog timer.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch sets min_cpus field for xlnx-versal-virt platform,
because it always creates XLNX_VERSAL_NR_ACPUS cpus even with
-smp 1 command line option.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 160343854912.8460.17915238517799132371.stgit@pasha-ThinkPad-X280
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When compiling with -Werror=implicit-fallthrough, gcc complains about
missing fallthrough annotations in this file. Looking at the code,
the fallthrough is very likely intended here, so add some comments
to silence the compiler warnings.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201020105938.23209-1-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The note test requires gcc 10 for -mbranch-protection=standard.
The mmap test uses PROT_BTI and does not require special compiler support.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the new generic support for NT_GNU_PROPERTY_TYPE_0.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-12-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is generic support, with the code disabled for all targets.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is slightly clearer than just using strerror, though
the different forms produced by error_setg_file_open and
error_setg_errno isn't entirely convenient.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-10-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a bit clearer than open-coding some of this
with a bare c string.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-9-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For BTI, we need to know if the executable is static or dynamic,
which means looking for PT_INTERP earlier.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The second loop uses a loop induction variable, and the first
does not. Transform the first to match the second, to simplify
a following patch moving code between them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-7-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixing this now will clarify following patches.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-6-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix an unlikely memory leak in load_elf_image().
Fixes: bf858897b7 ("linux-user: Re-use load_elf_image for the main binary.")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-5-richard.henderson@linaro.org
Message-Id: <20201003174944.1972444-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are all of the defines required to parse
GNU_PROPERTY_AARCH64_FEATURE_1_AND, copied from binutils.
Other missing defines related to other GNU program headers
and notes are elided for now.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Transform the prot bit to a qemu internal page bit, and save
it in the page tables.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The kernel sets btype for the signal handler as if for a call.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
-----BEGIN PGP SIGNATURE-----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=ZpMy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-10-26' into staging
* qtest fixes (e.g. memory leaks)
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
# gpg: Signature made Mon 26 Oct 2020 09:34:04 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-10-26: (31 commits)
tests/acceptance: Use .ppm extention for Portable PixMap files
tests/acceptance: Remove unused import
test/docker/dockerfiles: Add missing packages for acceptance tests
tests/acceptance: Enable AVOCADO_ALLOW_UNTRUSTED_CODE in the gitlab-CI
test/acceptance: Remove the CONTINUOUS_INTEGRATION tags
tests/acceptance/ppc_prep_40p: Fix the URL to the NetBSD-4.0 archive
scripts/oss-fuzz: ignore the generic-fuzz target
scripts/oss-fuzz: use hardlinks instead of copying
fuzz: register predefined generic-fuzz configs
fuzz: add generic-fuzz configs for oss-fuzz
fuzz: add an "opaque" to the FuzzTarget struct
fuzz: Add instructions for using generic-fuzz
scripts/oss-fuzz: Add crash trace minimization script
scripts/oss-fuzz: Add script to reorder a generic-fuzzer trace
fuzz: add a crossover function to generic-fuzzer
fuzz: add a DISABLE_PCI op to generic-fuzzer
fuzz: Add support for custom crossover functions
fuzz: Add fuzzer callbacks to DMA-read functions
fuzz: Declare DMA Read callback function
fuzz: Add DMA support to the generic-fuzzer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
