Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the Kconfig file is in disorder. Let's sort the options.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The name SIFIVE is too vague to convey the required component of
MSI_NONBROKEN. Let's drop the option, and select MSI_NONBROKEN in
each machine instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Every RISC-V machine needs riscv_hart hence there is no need to
have a dedicated Kconfig option for it. Drop the Kconfig option
and always build riscv_hart.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates one Cadence SDHCI controller.
On the Icicle Kit board, one eMMC chip and an external SD card
connect to this controller depending on different configuration.
As QEMU does not support eMMC yet, we just emulate the SD card
configuration. To test this, the Hart Software Services (HSS)
should choose the SD card configuration:
$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es
The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp
Note the generated SD card image should be resized before use:
$ qemu-img resize /path/to/sdcard.img 4G
Launch QEMU with the following command:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board
wires 4 of them out. Let's connect all 5 MMUARTs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is the initial commit of the Ibex UART device. Serial TX is
working, while RX has been implemeneted but untested.
This is based on the documentation from:
https://docs.opentitan.org/hw/ip/uart/doc/
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
This adds a barebone OpenTitan machine to QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
We extend QEMU RISC-V virt machine by adding Goldfish RTC device
to it. This will allow Guest Linux to sync it's local date/time
with Host date/time via RTC device.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add the CFI01 PFlash to the RISC-V virt board. This is the same PFlash
from the ARM Virt board and the implementation is based on the ARM Virt
board. This allows users to specify flash files from the command line.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use create_unimplemented_device() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-enable PCI_DEVICES for RISC-V.
The patch is based on other <arch>/Kconfig.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: 82a230d5a3 ("riscv-softmmu.mak: replace CONFIG_* with Kconfig "select" directives")
Message-Id: <20190311091256.18385-1-david.abdurachmanov@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>