The previous code section uses a 'first < 0' test and returns. Therefore,
there is no need to test the 'first' variable against '>= 0' afterwards.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the v8M security extension, there should be two systick
devices, which use separate banked systick exceptions. The
register interface is banked in the same way as for other
banked registers, including the existence of an NS alias
region for secure code to access the nonsecure timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-3-git-send-email-peter.maydell@linaro.org
Generalize nvic_sysreg_ns_ops so that we can pass it an
arbitrary MemoryRegion which it will use as the underlying
register implementation to apply the NS-alias behaviour
to. We'll want this so we can do the same with systick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-2-git-send-email-peter.maydell@linaro.org
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the very beginning, post_load() was called from common
reset. This is not standard and obliged to discriminate the
reset case from the restore case using the iidr value.
Let's get rid of that call.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix an incorrect mask expression in the handling of v7M MPU_RBAR
reads that meant that we would always report the ADDR field as zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1509732813-22957-1-git-send-email-peter.maydell@linaro.org
Remove the last few DPRINTFs from hw/intc/ioapic.c and turn
them into tracing. In one case it's a new trace, in the others
it's just adding a parameter to the existing traces.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171102180310.24760-1-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using the emulated XICS, the 'info pic' monitor command shows:
CPU 0 XIRR=ff000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10040060340
1000 MSI 05 00
1001 MSI 05 00
1002 MSI 05 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI 05 00
1009 MSI 05 00
100a MSI 05 00
100b MSI 05 00
100c MSI 05 00
but when using the in-kernel XICS with the very same guest, we get:
CPU 0 XIRR=00000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10032e00340
1000 MSI ff 00
1001 MSI ff 00
1002 MSI ff 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI ff 00
1009 MSI ff 00
100a MSI ff 00
100b MSI ff 00
100c MSI ff 00
ie, all irqs are masked and XIRR is null, while we should get the
same output as with the emulated XICS.
If the guest is then migrated, 'info pic' shows the expected values
on both source and destination.
The problem is that QEMU doesn't synchronize with KVM before printing
the XICS state. Migration happens to fix the output because it enforces
synchronization with KVM.
To fix the invalid output of 'info pic', this patch introduces a new
synchronize_state operation for both ICPStateClass and ICSStateClass.
The ICP operation relies on run_on_cpu() in order to kick the vCPU
and avoid sleeping on KVM_GET_ONE_REG.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS is not fully properly reset at the moment. Caches are
not emptied.
After a reset, in case we attempt to save the state before
the bound devices have registered their MSIs and after the
1st level table has been allocated by the ITS driver
(device BASER is valid), the first level entries are still
invalid. If the device cache is not empty (devices registered
before the reset), vgic_its_save_device_tables fails with -EINVAL.
This causes a QEMU abort().
Cc: qemu-stable@nongnu.org
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The commit cddafd8f35 ("hw/intc/arm_gicv3_its: Implement state save
/restore") breaks the backward compatibility with the older kernels
where vITS save/restore support is not available. The vmstate function
vm_change_state_handler() should not be registered if the running kernel
doesn't support ITS save/restore feature. Otherwise VM instance will be
killed whenever vmstate callback function is invoked.
Observed a virtual machine shutdown with QEMU-2.10+linux-4.11 when testing
the reboot command "virsh reboot <domain> --mode acpi" instead of reboot.
KVM Error: 'KVM_SET_DEVICE_ATTR failed: Group 4 attr 0x00000000000001'
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1509712671-16299-1-git-send-email-shankerd@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add OpenRISC Multicore PIC which handles inter processor interrupts
(IPI) between cores. In OpenRISC all device interrupts are routed to
each core enabling this device to be simple.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
This calculation of the first exception vector in
the ITNS<n> register being accessed:
int startvec = 32 * (offset - 0x380) + NVIC_FIRST_IRQ;
is incorrect, because offset is in bytes, so we only want
to multiply by 8.
Spotted by Coverity (CID 1381484, CID 1381488), though it is
not correct that it actually overflows the buffer, because
we have a 'startvec + i < s->num_irq' guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507650856-11718-1-git-send-email-peter.maydell@linaro.org
Coverity points out that we forgot the 'break' for
the SAU_CTRL write case (CID1381683). This has
no actual visible consequences because it happens
that the following case is effectively a no-op.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1507742676-9908-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
When we added support for the new SHCSR bits in v8M in commit
437d59c17e the code to support writing to the new HARDFAULTPENDED
bit was accidentally only added for non-secure writes; the
secure banked version of the bit should also be writable.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-21-git-send-email-peter.maydell@linaro.org
Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Reset for devices does not include an automatic clear of the
device state (unlike CPU state, where most of the state
structure is cleared to zero). Add some missing initialization
of NVIC state that meant that the device was left in the wrong
state if the guest did a warm reset.
(In particular, since we were resetting the computed state like
s->exception_prio but not all the state it was computed
from like s->vectors[x].active, the NVIC wound up in an
inconsistent state that could later trigger assertion failures.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1506092407-26985-2-git-send-email-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=/+LV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170927a' into staging
Migration pull 2017-09-27
# gpg: Signature made Wed 27 Sep 2017 14:56:23 BST
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170927a:
migration: Route more error paths
migration: Route errors up through vmstate_save
migration: wire vmstate_save_state errors up to vmstate_subsection_save
migration: Check field save returns
migration: check pre_save return in vmstate_save_state
migration: pre_save return int
migration: disable auto-converge during bulk block migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Apple uses an IBM MPIC2A without timers, it has 64 sources.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq()
to handle banked exceptions:
* acknowledge needs to use the correct vector, which may be
in sec_vectors[]
* acknowledge needs to return to its caller whether the
exception should be taken to secure or non-secure state
* complete needs its caller to tell it whether the exception
being completed is a secure one or not
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org
Handle banking of SHCSR: some register bits are banked between
Secure and Non-Secure, and some are only accessible to Secure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-19-git-send-email-peter.maydell@linaro.org
The ICSR NVIC register is banked for v8M. This doesn't
require any new state, but it does mean that some bits
are controlled by BFHNFNMINS and some bits must work
with the correct banked exception. There is also a new
in v8M PENDNMICLR bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-18-git-send-email-peter.maydell@linaro.org
Now that we have a banked FAULTMASK register and banked exceptions,
we can implement the correct check in cpu_mmu_index() for whether
the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes
handlers which have requested a negative execution priority to run
with the MPU disabled. In v8M the test has to check this for the
current security state and so takes account of banking.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org
Update nvic_exec_prio() to support the v8M changes:
* BASEPRI, FAULTMASK and PRIMASK are all banked
* AIRCR.PRIS can affect NS priorities
* AIRCR.BFHFNMINS affects FAULTMASK behaviour
These changes mean that it's no longer possible to
definitely say that if FAULTMASK is set it overrides
PRIMASK, and if PRIMASK is set it overrides BASEPRI
(since if PRIMASK_NS is set and AIRCR.PRIS is set then
whether that 0x80 priority should take effect or the
priority in BASEPRI_S depends on the value of BASEPRI_S,
for instance). So we switch to the same approach used
by the pseudocode of working through BASEPRI, PRIMASK
and FAULTMASK and overriding the previous values if
needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-16-git-send-email-peter.maydell@linaro.org
If AIRCR.BFHFNMINS is clear, then although NonSecure HardFault
can still be pended via SHCSR.HARDFAULTPENDED it mustn't actually
preempt execution. The simple way to achieve this is to clear the
enable bit for it, since the enable bit isn't guest visible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-15-git-send-email-peter.maydell@linaro.org
In v7M, the fixed-priority exceptions are:
Reset: -3
NMI: -2
HardFault: -1
In v8M, this changes because Secure HardFault may need
to be prioritised above NMI:
Reset: -4
Secure HardFault if AIRCR.BFHFNMINS == 1: -3
NMI: -2
Secure HardFault if AIRCR.BFHFNMINS == 0: -1
NonSecure HardFault: -1
Make these changes, including support for changing the
priority of Secure HardFault as AIRCR.BFHFNMINS changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-14-git-send-email-peter.maydell@linaro.org
When escalating to HardFault, we must go into Lockup if we
can't take the synchronous HardFault because the current
execution priority is already at or below the priority of
HardFault. In v7M HF is always priority -1 so a simple < 0
comparison sufficed; in v8M the priority of HardFault can
vary depending on whether it is a Secure or NonSecure
HardFault, so we must check against the priority of the
HardFault exception vector we're about to use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-13-git-send-email-peter.maydell@linaro.org
In armv7m_nvic_set_pending() we have to compare the
priority of an exception against the execution priority
to decide whether it needs to be escalated to HardFault.
In the specification this is a comparison against the
exception's group priority; for v7M we implemented it
as a comparison against the raw exception priority
because the two comparisons will always give the
same answer. For v8M the existence of AIRCR.PRIS and
the possibility of different PRIGROUP values for secure
and nonsecure exceptions means we need to explicitly
calculate the vector's group priority for this check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-12-git-send-email-peter.maydell@linaro.org
Make the set_prio() function take a bool indicating
whether to pend the secure or non-secure version of a banked
interrupt, and use this to implement the correct banking
semantics for the SHPR registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-11-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
Update the nvic_recompute_state() code to handle the security
extension and its associated banked registers.
Code that uses the resulting cached state (ie the irq
acknowledge and complete code) will be updated in a later
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-9-git-send-email-peter.maydell@linaro.org
For v8M, the NVIC has a new set of registers per interrupt,
NVIC_ITNS<n>. These determine whether the interrupt targets Secure
or Non-secure state. Implement the register read/write code for
these, and make them cause NVIC_IABR, NVIC_ICER, NVIC_ISER,
NVIC_ICPR, NVIC_IPR and NVIC_ISPR to RAZ/WI for non-secure
accesses to fields corresponding to interrupts which are
configured to target secure state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-8-git-send-email-peter.maydell@linaro.org
Update the code in nvic_rettobase() so that it checks the
sec_vectors[] array as well as the vectors[] array if needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-7-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
Instead of looking up the pending priority
in nvic_pending_prio(), cache it in a new state struct
field. The calculation of the pending priority given
the interrupt number is more complicated in v8M with
the security extension, so the caching will be worthwhile.
This changes nvic_pending_prio() from returning a full
(group + subpriority) priority value to returning a group
priority. This doesn't require changes to its callsites
because we use it only in comparisons of the form
execution_prio > nvic_pending_prio()
and execution priority is always a group priority, so
a test (exec prio > full prio) is true if and only if
(execprio > group_prio).
(Architecturally the expected comparison is with the
group priority for this sort of "would we preempt" test;
we were only doing a test with a full priority as an
optimisation to avoid the mask, which is possible
precisely because the two comparisons always give the
same answer.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-5-git-send-email-peter.maydell@linaro.org
With banked exceptions, just the exception number in
s->vectpending is no longer sufficient to uniquely identify
the pending exception. Add a vectpending_is_s_banked bool
which is true if the exception is using the sec_vectors[]
array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1505240046-11454-4-git-send-email-peter.maydell@linaro.org
For the v8M security extension, some exceptions must be banked
between security states. Add the new vecinfo array which holds
the state for the banked exceptions and migrate it if the
CPU the NVIC is attached to implements the security extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
-----BEGIN PGP SIGNATURE-----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=GAd3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20170915' into staging
ppc patch queue 2017-09-15
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
# gpg: Signature made Fri 15 Sep 2017 04:50:00 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20170915:
ppc/kvm: use kvm_vm_check_extension() in kvmppc_is_pr()
spapr_events: use QTAILQ_FOREACH_SAFE() in spapr_clear_pending_events()
spapr_cpu_core: cleaning up qdev_get_machine() calls
spapr_pci: don't create 64-bit MMIO window if we don't need to
spapr_pci: convert sprintf() to g_strdup_printf()
spapr_cpu_core: fail gracefully with non-pseries machine types
xics: fix several error leaks
vfio, spapr: Fix levels calculation
spapr_pci: handle FDT creation errors with _FDT()
spapr_pci: use the common _FDT() helper
spapr: fix CAS-generated reset
ppc/xive: fix OV5_XIVE_EXPLOIT bits
spapr: only update SDR1 once per-cpu during CAS
spapr_pci: use g_strdup_printf()
spapr_pci: drop useless check in spapr_populate_pci_child_dt()
spapr_pci: drop useless check in spapr_phb_vfio_get_loc_code()
hw/ppc/spapr.c: cleaning up qdev_get_machine() calls
net: Add SunGEM device emulation as found on Apple UniNorth
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If object_property_get_link() fails then it allocates an error, which
must be freed before returning. The error_get_pretty() function is
merely an accessor to the error message and doesn't free anything.
The error.h header indicates how to do it right:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In several places we were unconditionally applying the
nvic_gprio_mask() to a priority value. This is incorrect
if the priority is one of the fixed negative priority
values (for NMI and HardFault), so don't do it.
This bug would have caused both NMI and HardFault to be
considered as the same priority and so NMI wouldn't
correctly preempt HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505137930-13255-5-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
For v8M the range 0xe002e000..0xe002efff is an alias region which
for secure accesses behaves like a NonSecure access to the main
SCS region. (For nonsecure accesses including when the security
extension is not implemented, it is RAZ/WI.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-11-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
Fix the following warning:
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: warning: logical not is only applied to the left hand side of this bitwise operator [-Wlogical-not-parentheses]
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^ ~
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses after the '!' to evaluate the bitwise operator first
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses around left hand side expression to silence this warning
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
This logic error meant we were not setting the PTZ
bit when we should -- luckily as the comment suggests
this wouldn't have had any effects beyond making GIC
initialization take a little longer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Message-id: 20170829173226.7625-1-bobby.prani@gmail.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARMv7M architecture specifies that most of the addresses in the
PPB region (which includes the NVIC, systick and system registers)
are not accessible to unprivileged accesses, which should
BusFault with a few exceptions:
* the STIR is configurably user-accessible
* the ITM (which we don't implement at all) is always
user-accessible
Implement this by switching the register access functions
to the _with_attrs scheme that lets us distinguish user
mode accesses.
This allows us to pull the handling of the CCR.USERSETMPEND
flag up to the level where we can make it generate a BusFault
as it should for non-permitted accesses.
Note that until the core ARM CPU code implements turning
MEMTX_ERROR into a BusFault the registers will continue to
act as RAZ/WI to user accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-16-git-send-email-peter.maydell@linaro.org
The armv7m_nvic.h header file was accidentally placed in
include/hw/arm; move it to include/hw/intc to match where
its corresponding .c file lives.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-15-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
Remove an out of date comment which says there's only one
item in the NVIC container region -- we put systick into its
own device object a while back and so now there are two
things in the container.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-6-git-send-email-peter.maydell@linaro.org
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During migration we should transfer ais states to the target guest.
This patch introduces a subsection to kvm_s390_flic_vmstate and new
vmsd for qemu_flic. The ais states need to be migrated only when
ais is supported.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
zPCI instructions and facilities are available since IBM zEnterprise
EC12. To support z/PCI in QEMU we enable zpci, aen and ais facilities
starting with zEC12 GA1. And we always set zpci and aen bits in max cpu
model. Later they might be switched off due to applied real cpu model.
For ais bit, we only provide it in the full cpu model beginning with
zEC12 and defer its enablement in the default cpu model to a later point
in time. At the same time, disable them for 2.9 and older machines.
Because of introducing AIS facility, we could check if it's enabled to
initialize flic->ais_supported with the real value.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Although we have recently vmstatified the migration of some css
infrastructure, for some css entities there is still state to be
migrated left, because the focus was keeping migration stream
compatibility (that is basically everything as-is).
Let us add vmstate helpers and extend existing vmstate descriptions so
that we have everything we need. Let us guard the added state via
css_migration_enabled, so we keep the compatible behavior if css
migration is disabled.
Let's also annotate the bits which do not need to be migrated for better
readability.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170711145441.33925-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's introduce a specialized way to inject adapter interrupts that,
unlike the common interrupt injection method, allows to take the
characteristics of the adapter into account.
For adapters subject to AIS facility:
- for non-kvm case, we handle the suppression for a given ISC in QEMU.
- for kvm case, we pass adapter id to kvm to do airq injection.
Add add tracepoint for suppressed airq and suppressing airq.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to emulate the adapter interruption suppression (AIS)
facility properly, the guest needs to be able to modify the AIS mask.
Interrupt suppression will be handled via the flic (for kvm, via a
recently introduced kernel backend; for !kvm, in the flic code), so
let's introduce a method to change the mode via the flic interface.
We introduce the 'simm' and 'nimm' fields to QEMUS390FLICState
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Co-authored-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit f6f4ce4211 ("s390x: add property adapter_routes_max_batch",
2016-12-09) introduces a common realize (intended to be common for all
the subclasses) for flic, but fails to make sure the kvm-flic which had
its own is actually calling this common realize.
This omission fortunately does not result in a grave problem. The common
realize was only supposed to catch a possible programming mistake by
validating a value of a property set via the compat machine macros. Since
there was no programming mistake we don't need this fixed for stable.
Let's fix this problem by making sure kvm flic honors the realize of its
parent class.
Let us also improve on the error message we would hypothetically emit
when the validation fails.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: f6f4ce4211 ("s390x: add property adapter_routes_max_batch")
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
From the moment it was introduced by commit a2875e6f98 ("s390x/kvm:
implement floating-interrupt controller device", 2013-07-16) the kvm-flic
is not making realize fail properly in case it's impossible to create the
KVM device which basically serves as a backend and is absolutely
essential for having an operational kvm-flic.
Let's fix this by making sure we do proper error propagation in realize.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: a2875e6f98 "s390x/kvm: implement floating-interrupt controller device"
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's vmstatify virtio_ccw_save_config and virtio_ccw_load_config for
flexibility (extending using subsections) and for fun.
To achieve this we need to hack the config_vector, which is VirtIODevice
(that is common virtio) state, in the middle of the VirtioCcwDevice state
representation. This is somewhat ugly, but we have no choice because the
stream format needs to be preserved.
Almost no changes in behavior. Exception is everything that comes with
vmstate like extra bookkeeping about what's in the stream, and maybe some
extra checks and better error reporting.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170703213414.94298-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Previously QEMU open-pic implemented the 4 open-pic timers including
all timer registers, but the timers did not "count" or generate any
interrupts. The patch makes the timers both count and generate
interrupts. The timer clock frequency is fixed at 25MHZ.
--
Responding to V2 patch comments.
- Simplify clock frequency logic and commentary.
- Remove camelCase variables.
- Timer objects now created at init rather than lazily.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICPState objects are currently registered to vmstate as qdev objects.
Their instance ids are hence computed automatically in the migration code,
and thus depends on the order the CPU cores were plugged.
If the destination had its CPU cores plugged in a different order than the
source, then ICPState objects will have different instance_ids and load
the wrong state.
Since CPU objects have a reliable cpu_index which is already used as
instance_id in vmstate, let's use it for ICPState as well.
Please note that this doesn't break migration. Older machine types used to
allocate and realize all ICPState objects at machine init time, for the whole
lifetime of the machine. The qdev instance ids are thus 0,1,2... nr_servers
and happen to map to the vCPU indexes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In some cases a failing VMSTATE_*_EQUAL does not mean we detected a bug,
but it's actually the best we can do. Especially in these cases a verbose
error message is required.
Let's introduce infrastructure for specifying a error hint to be used if
equal check fails. Let's do this by adding a parameter to the _EQUAL
macros called _err_hint. Also change all current users to pass NULL as
last parameter so nothing changes for them.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170623144823.42936-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
TYPE_ARM_CPU's property "mp-affinity" is defined with
DEFINE_PROP_UINT64().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-35-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The getter and setter of TYPE_APIC_COMMON property "id" are
apic_common_get_id() and apic_common_set_id().
apic_common_get_id() reads either APICCommonState member uint32_t
initial_apic_id or uint8_t id into an int64_t local variable. It then
passes this variable to visit_type_int().
apic_common_set_id() uses visit_type_int() to read the value into a
local variable, which it then assigns both to initial_apic_id and id.
While the state backing the property is two unsigned members, 8 and 32
bits wide, the actual visitor is 64 bits signed.
Change getter and setter to use visit_type_uint32(). Then everything's
uint32_t, except for @id.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-19-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We change the restoration priority of both the GICv3 and ITS. The
GICv3 must be restored before the ITS and the ITS needs to be restored
before PCIe devices since it translates their MSI transactions.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 1497023553-18411-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the flush of the LPI pending bits into the
redistributor pending tables. This happens on VM stop.
There is no explicit restore as the tables are implicitly sync'ed
on ITS table restore and on LPI enable at redistributor level.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We need to handle both registers and ITS tables. While
register handling is standard, ITS table handling is more
challenging since the kernel API is devised so that the
tables are flushed into guest RAM and not in vmstate buffers.
Flushing the ITS tables on device pre_save() is too late
since the guest RAM is already saved at this point.
Table flushing needs to happen when we are sure the vcpus
are stopped and before the last dirty page saving. The
right point is RUN_STATE_FINISH_MIGRATE but sometimes the
VM gets stopped before migration launch so let's simply
flush the tables each time the VM gets stopped.
For regular ITS registers we just can use vmstate pre_save()
and post_load() callbacks.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-3-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In some circumstances, we don't want to abort if the
kvm_device_access fails. This will be the case during ITS
migration, in case the ITS table save/restore fails because
the guest did not program the vITS correctly. So let's pass an
error object to the function and return the ioctl value. New
callers will be able to make a decision upon this returned
value.
Existing callers pass &error_abort which will cause the
function to abort on failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 1497023553-18411-2-git-send-email-eric.auger@redhat.com
[PMM: wrapped long line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The static array of interrupt combiner mappings is not modified so it
can be made const for code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are to SysBusDevice variables in exynos4210_gic_realize()
function: one for the device itself and second for arm_gic device. Add
a prefix "gic" to the second one so it will be easier to understand the
code.
While at it, put local uninitialized 'i' variable at the end, next to
other uninitialized ones.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cpu_setup() handler is only implemented by xics_kvm, where it really
does a typical "realize" job. Moreover, the realize() handler is called
shortly after cpu_setup(), on the same path.
This patch converts xics_kvm to implement realize() instead of cpu_setup().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Until recently, spapr used to allocate ICPState objects for the lifetime
of the machine. They would only be associated to vCPUs in xics_cpu_setup()
when plugging a CPU core.
Now that ICPState objects have the same lifecycle as vCPUs, it is
possible to associate them during realization.
This patch hence open-codes xics_cpu_setup() in icp_realize(). The vCPU
is passed as a property. Note that vCPU now needs to be realized first
for the IRQs to be allocated. It also needs to resetted before ICPState
realization in order to synchronize with KVM.
Since ICPState objects are freed when unrealized, xics_cpu_destroy() isn't
needed anymore and can be safely dropped.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It makes more sense to pass an IPCState * to handlers of ICPStateClass
instead of a DeviceState *, if only to benefit from compile time type
checking. The same goes with ICSStateClass.
While here, we also change the declaration of ICPStateClass in xics.h
for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These properties are part of the XICS API. They deserve to appear
explicitely in the XICS header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Taking into account that qemu_set_irq() returns immediatly if its first
argument is NULL, icp_kvm_reset() largely duplicates icp_reset().
This patch introduces a reset() handler, so that the common logic can
be implemented in icp_reset() only.
While there we can also drop icp_kvm_realize() and icp_kvm_unrealize(). This
causes icp-kvm to be realized in icp_realize(), which sets icp->xics, but
it has no impact.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If EL3 is not implemented (ie only one security state) then the
one and only ICC_BPR1 register behaves like the Non-secure
ICC_BPR1 in an EL3-present configuration. In particular, its
reset value is GIC_MIN_BPR_NS, not GIC_MIN_BPR.
Correct the erroneous reset value; this fixes a problem where
we might hit the assert added in commit a89ff39ee9.
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1496849369-30282-1-git-send-email-peter.maydell@linaro.org
openpic_tmr_read() is incorrectly computing register offset of the
TCCR, TBCR, TVPR, and TDR registers when accessing the open pic timer
registers. Specifically the offset of timer registers for
openpic_tmr_read() is not accounting for the timer frequency reporting
register (TFFR) which is the first register in the "tmr" memory
region.
openpic_tmr_write() *is* correctly computing the offset by adding
0x10f0 to the address prior to computing the register index. This
patch instead subtracts 0x10 in both the read and write routines and
eliminates some other gratuitous differences between the functions.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----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=tEkM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20170601' into staging
migration/next for 20170601
# gpg: Signature made Thu 01 Jun 2017 17:51:04 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20170601:
migration: Move include/migration/block.h into migration/
migration: Export ram.c functions in its own file
migration: Create include for migration snapshots
migration: Export rdma.c functions in its own file
migration: Export tls.c functions in its own file
migration: Export socket.c functions in its own file
migration: Export fd.c functions in its own file
migration: Export exec.c functions in its own file
migration: Split qemu-file.h
migration: Remove unneeded includes of migration/vmstate.h
migration: shut src return path unconditionally
migration: fix leak of src file on dst
migration: Remove section_id parameter from vmstate_load
migration: loadvm handlers are not used
migration: Use savevm_handlers instead of loadvm copy
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M series MPU is almost the same as the already implemented R
profile MPU (v7 PMSA). So all we need to implement here is the MPU
register interface in the system register space.
This implementation has the same restriction as the R profile MPU
that it doesn't permit regions to be sized down smaller than 1K.
We also do not yet implement support for MPU_CTRL.HFNMIENA; this
bit should if zero disable use of the MPU when running HardFault,
NMI or with FAULTMASK set to 1 (ie at an execution priority of
less than zero) -- if the MPU is enabled we don't treat these
cases any differently.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Message-id: 1493122030-32191-13-git-send-email-peter.maydell@linaro.org
[PMM: Keep all the bits in mpu_ctrl field, rather than
using SCTLR bits for them; drop broken HFNMIENA support;
various cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
